diff mbox series

[v2,05/10] phy: add A3700 UTMI PHY driver

Message ID 20190111133133.24803-6-miquel.raynal@bootlin.com (mailing list archive)
State New, archived
Headers show
Series A3700 USB S2RAM support | expand

Commit Message

Miquel Raynal Jan. 11, 2019, 1:31 p.m. UTC 
Marvell Armada 3700 SoC has two USB controllers, each of them being
wired to an internal UTMI PHY. Add a driver to control them.

Igal Liberman worked on supporting the PHY, I took the while 'register
configuration' from his work and rewrote almost entirely the
driver/bindings around it.

Co-developed-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Igal Liberman <igall@marvell.com>
---
 drivers/phy/marvell/Kconfig                |   9 +
 drivers/phy/marvell/Makefile               |   1 +
 drivers/phy/marvell/phy-mvebu-a3700-utmi.c | 297 +++++++++++++++++++++
 3 files changed, 307 insertions(+)
 create mode 100644 drivers/phy/marvell/phy-mvebu-a3700-utmi.c

Comments

Chunfeng Yun (云春峰) Jan. 15, 2019, 2:40 a.m. UTC | #1 
Hi,
On Fri, 2019-01-11 at 14:31 +0100, Miquel Raynal wrote:
> Marvell Armada 3700 SoC has two USB controllers, each of them being
> wired to an internal UTMI PHY. Add a driver to control them.
> 
> Igal Liberman worked on supporting the PHY, I took the while 'register
> configuration' from his work and rewrote almost entirely the
> driver/bindings around it.
> 
> Co-developed-by: Igal Liberman <igall@marvell.com>
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> Signed-off-by: Igal Liberman <igall@marvell.com>
> ---
>  drivers/phy/marvell/Kconfig                |   9 +
>  drivers/phy/marvell/Makefile               |   1 +
>  drivers/phy/marvell/phy-mvebu-a3700-utmi.c | 297 +++++++++++++++++++++
>  3 files changed, 307 insertions(+)
>  create mode 100644 drivers/phy/marvell/phy-mvebu-a3700-utmi.c
> 
> diff --git a/drivers/phy/marvell/Kconfig b/drivers/phy/marvell/Kconfig
> index 9c90c0408ea3..b8e9dd38ad0d 100644
> --- a/drivers/phy/marvell/Kconfig
> +++ b/drivers/phy/marvell/Kconfig
> @@ -33,6 +33,15 @@ config PHY_MVEBU_A3700_COMPHY
>  	  shared serdes PHYs on Marvell Armada 3700. Its serdes lanes can be
>  	  used by various controllers: Ethernet, SATA, USB3, PCIe.
>  
> +config PHY_MVEBU_A3700_UTMI
> +	tristate "Marvell A3700 UTMI driver"
> +	depends on ARCH_MVEBU || COMPILE_TEST
> +	depends on OF
> +	default y
> +	select GENERIC_PHY
> +	help
> +	  Enable this to support Marvell A3700 UTMI PHY driver.
> +
>  config PHY_MVEBU_CP110_COMPHY
>  	tristate "Marvell CP110 comphy driver"
>  	depends on ARCH_MVEBU || COMPILE_TEST
> diff --git a/drivers/phy/marvell/Makefile b/drivers/phy/marvell/Makefile
> index c13a0c8ab6f0..82f291cf59ee 100644
> --- a/drivers/phy/marvell/Makefile
> +++ b/drivers/phy/marvell/Makefile
> @@ -3,6 +3,7 @@ obj-$(CONFIG_ARMADA375_USBCLUSTER_PHY)	+= phy-armada375-usb2.o
>  obj-$(CONFIG_PHY_BERLIN_SATA)		+= phy-berlin-sata.o
>  obj-$(CONFIG_PHY_BERLIN_USB)		+= phy-berlin-usb.o
>  obj-$(CONFIG_PHY_MVEBU_A3700_COMPHY)	+= phy-mvebu-a3700-comphy.o
> +obj-$(CONFIG_PHY_MVEBU_A3700_UTMI)	+= phy-mvebu-a3700-utmi.o
>  obj-$(CONFIG_PHY_MVEBU_CP110_COMPHY)	+= phy-mvebu-cp110-comphy.o
>  obj-$(CONFIG_PHY_MVEBU_SATA)		+= phy-mvebu-sata.o
>  obj-$(CONFIG_PHY_PXA_28NM_HSIC)		+= phy-pxa-28nm-hsic.o
> diff --git a/drivers/phy/marvell/phy-mvebu-a3700-utmi.c b/drivers/phy/marvell/phy-mvebu-a3700-utmi.c
> new file mode 100644
> index 000000000000..97d8235d661d
> --- /dev/null
> +++ b/drivers/phy/marvell/phy-mvebu-a3700-utmi.c
> @@ -0,0 +1,297 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2018 Marvell
> + *
> + * Authors:
> + *   Evan Wang <xswang@marvell.com>
> + *   Miquèl Raynal <miquel.raynal@bootlin.com>
> + *
> + * Marvell A3700 UTMI PHY driver
> + */
> +
> +#include <linux/io.h>
> +#include <linux/iopoll.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +
> +/* Armada 3700 UTMI PHY registers */
> +#define USB2_PHY_PLL_CTRL_REG0			0x0
> +#define   PLL_REF_DIV_OFF			0
> +#define   PLL_REF_DIV_MASK			(0x7F << PLL_REF_DIV_OFF)
use GENMASK?
> +#define   PLL_REF_DIV_5				0x5
> +#define   PLL_FB_DIV_OFF			16
> +#define   PLL_FB_DIV_MASK			(0x1FF << PLL_FB_DIV_OFF)
> +#define   PLL_FB_DIV_96				96
> +#define   PLL_SEL_LPFR_OFF			28
> +#define   PLL_SEL_LPFR_MASK			(0x3 << PLL_SEL_LPFR_OFF)
> +#define   PLL_READY				BIT(31)
> +#define USB2_PHY_CAL_CTRL			0x8
> +#define   PHY_PLLCAL_DONE			BIT(31)
> +#define   PHY_IMPCAL_DONE			BIT(23)
> +#define USB2_RX_CHAN_CTRL1			0x18
> +#define   USB2PHY_SQCAL_DONE			BIT(31)
> +#define USB2_PHY_OTG_CTRL			0x34
> +#define   PHY_PU_OTG				BIT(4)
> +#define USB2_PHY_CHRGR_DETECT			0x38
> +#define   PHY_CDP_EN				BIT(2)
> +#define   PHY_DCP_EN				BIT(3)
> +#define   PHY_PD_EN				BIT(4)
> +#define   PHY_PU_CHRG_DTC			BIT(5)
> +#define   PHY_CDP_DM_AUTO			BIT(7)
> +#define   PHY_ENSWITCH_DP			BIT(12)
> +#define   PHY_ENSWITCH_DM			BIT(13)
> +
> +/* Armada 3700 USB miscellaneous registers */
> +#define USB2_PHY_CTRL(usb32)			(usb32 ? 0x20 : 0x4)
> +#define   RB_USB2PHY_PU				BIT(0)
> +#define   USB2_DP_PULLDN_DEV_MODE		BIT(5)
> +#define   USB2_DM_PULLDN_DEV_MODE		BIT(6)
> +#define   RB_USB2PHY_SUSPM(usb32)		(usb32 ? BIT(14) : BIT(7))
> +
> +#define PLL_LOCK_DELAY_US			10000
> +#define PLL_LOCK_TIMEOUT_US			1000000
> +
> +/**
> + * struct mvebu_a3700_utmi_caps - PHY capabilities
> + *
> + * @usb32: Flag indicating which PHY is in use (impacts the register map):
> + *           - The UTMI PHY wired to the USB3/USB2 controller (otg)
> + *           - The UTMI PHY wired to the USB2 controller (host only)
> + * @ops: PHY operations
> + */
> +struct mvebu_a3700_utmi_caps {
> +	int usb32;
> +	const struct phy_ops *ops;
> +};
> +
> +/**
> + * struct mvebu_a3700_utmi - PHY driver data
> + *
> + * @regs: PHY registers
> + * @usb_mis: Regmap with USB miscellaneous registers including PHY ones
> + * @caps: PHY capabilities
> + * @phy: PHY handle
> + */
> +struct mvebu_a3700_utmi {
> +	void __iomem *regs;
> +	struct regmap *usb_misc;
> +	const struct mvebu_a3700_utmi_caps *caps;
> +	struct phy *phy;
> +};
> +
> +static int mvebu_a3700_utmi_phy_power_on(struct phy *phy)
> +{
> +	struct mvebu_a3700_utmi *utmi = phy_get_drvdata(phy);
> +	struct device *dev = &phy->dev;
> +	int usb32 = utmi->caps->usb32;
> +	int ret = 0;
> +	u32 reg;
> +
> +	if (!utmi)
> +		return -ENODEV;
the check here may be not necessary
> +
> +	/*
> +	 * Setup PLL. 40MHz clock used to be the default, bein 25MHz now.
> +	 * See "PLL Settings for Typical REFCLK" table.
> +	 */
> +	reg = readl(utmi->regs + USB2_PHY_PLL_CTRL_REG0);
> +	reg &= ~(PLL_REF_DIV_MASK | PLL_FB_DIV_MASK | PLL_SEL_LPFR_MASK);
> +	reg |= (PLL_REF_DIV_5 << PLL_REF_DIV_OFF |
> +		PLL_FB_DIV_96 << PLL_FB_DIV_OFF);
> +	writel(reg, utmi->regs + USB2_PHY_PLL_CTRL_REG0);
> +
> +	/* Enable PHY pull up and disable USB2 suspend */
> +	regmap_update_bits(utmi->usb_misc, USB2_PHY_CTRL(usb32),
> +			   RB_USB2PHY_SUSPM(usb32) | RB_USB2PHY_PU,
> +			   RB_USB2PHY_SUSPM(usb32) | RB_USB2PHY_PU);
> +
> +	if (usb32) {
> +		/* Power up OTG module */
> +		reg = readl(utmi->regs + USB2_PHY_OTG_CTRL);
> +		reg |= PHY_PU_OTG;
> +		writel(reg, utmi->regs + USB2_PHY_OTG_CTRL);
> +
> +		/* Disable PHY charger detection */
> +		reg = readl(utmi->regs + USB2_PHY_CHRGR_DETECT);
> +		reg &= ~(PHY_CDP_EN | PHY_DCP_EN | PHY_PD_EN | PHY_PU_CHRG_DTC |
> +			 PHY_CDP_DM_AUTO | PHY_ENSWITCH_DP | PHY_ENSWITCH_DM);
> +		writel(reg, utmi->regs + USB2_PHY_CHRGR_DETECT);
> +
> +		/* Disable PHY DP/DM pull-down (used for device mode) */
> +		regmap_update_bits(utmi->usb_misc, USB2_PHY_CTRL(usb32),
> +				   USB2_DP_PULLDN_DEV_MODE |
> +				   USB2_DM_PULLDN_DEV_MODE, 0);
> +	}
> +
> +	/* Wait for PLL calibration */
> +	ret = readl_poll_timeout(utmi->regs + USB2_PHY_CAL_CTRL, reg,
> +				 reg & PHY_PLLCAL_DONE,
> +				 PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
> +	if (ret) {
> +		dev_err(dev, "Failed to end USB2 PLL calibration\n");
> +		return ret;
> +	}
> +
> +	/* Wait for impedance calibration */
> +	ret = readl_poll_timeout(utmi->regs + USB2_PHY_CAL_CTRL, reg,
> +				 reg & PHY_IMPCAL_DONE,
> +				 PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
> +	if (ret) {
> +		dev_err(dev, "Failed to end USB2 impedance calibration\n");
> +		return ret;
> +	}
> +
> +	/* Wait for squetch calibration */
> +	ret = readl_poll_timeout(utmi->regs + USB2_RX_CHAN_CTRL1, reg,
> +				 reg & USB2PHY_SQCAL_DONE,
> +				 PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
> +	if (ret) {
> +		dev_err(dev, "Failed to end USB2 unknown calibration\n");
> +		return ret;
> +	}
> +
> +	/* Wait for PLL to be locked */
> +	ret = readl_poll_timeout(utmi->regs + USB2_PHY_PLL_CTRL_REG0, reg,
> +				 reg & PLL_READY,
> +				 PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
> +	if (ret)
> +		dev_err(dev, "Failed to lock USB2 PLL\n");
> +
> +	return ret;
> +}
> +
> +static int mvebu_a3700_utmi_phy_power_off(struct phy *phy)
> +{
> +	struct mvebu_a3700_utmi *utmi = phy_get_drvdata(phy);
> +	int usb32 = utmi->caps->usb32;
> +	u32 reg;
> +
> +	if (!utmi)
> +		return -ENODEV;
> +
> +	/* Disable PHY pull-up and enable USB2 suspend */
> +	reg = readl(utmi->regs + USB2_PHY_CTRL(usb32));
> +	reg &= ~(RB_USB2PHY_PU | RB_USB2PHY_SUSPM(usb32));
> +	writel(reg, utmi->regs + USB2_PHY_CTRL(usb32));
> +
> +	/* Power down OTG module */
> +	if (usb32) {
> +		reg = readl(utmi->regs + USB2_PHY_OTG_CTRL);
> +		reg &= ~PHY_PU_OTG;
> +		writel(reg, utmi->regs + USB2_PHY_OTG_CTRL);
> +	}
> +
> +	return 0;
> +}
> +
> +static const struct phy_ops mvebu_a3700_utmi_phy_ops = {
> +	.power_on = mvebu_a3700_utmi_phy_power_on,
> +	.power_off = mvebu_a3700_utmi_phy_power_off,
> +	.owner = THIS_MODULE,
> +};
> +
> +static const struct mvebu_a3700_utmi_caps mvebu_a3700_utmi_otg_phy_caps = {
> +	.usb32 = true,
> +	.ops = &mvebu_a3700_utmi_phy_ops,
> +};
> +
> +static const struct mvebu_a3700_utmi_caps mvebu_a3700_utmi_host_phy_caps = {
> +	.usb32 = false,
> +	.ops = &mvebu_a3700_utmi_phy_ops,
> +};
> +
> +static const struct of_device_id mvebu_a3700_utmi_of_match[] = {
> +	{
> +		.compatible = "marvell,a3700-utmi-otg-phy",
> +		.data = &mvebu_a3700_utmi_otg_phy_caps,
> +	},
> +	{
> +		.compatible = "marvell,a3700-utmi-host-phy",
> +		.data = &mvebu_a3700_utmi_host_phy_caps,
> +	},
> +	{},
> +};
> +MODULE_DEVICE_TABLE(of, mvebu_a3700_utmi_of_match);
> +
> +static int mvebu_a3700_utmi_phy_probe(struct platform_device *pdev)
> +{
> +	const struct of_device_id *dev_id;
> +	struct device *dev = &pdev->dev;
> +	struct mvebu_a3700_utmi *utmi;
> +	struct phy_provider *provider;
> +	const struct phy_ops *ops;
> +	struct resource *res;
> +
> +	utmi = devm_kzalloc(dev, sizeof(*utmi), GFP_KERNEL);
> +	if (!utmi)
> +		return -ENOMEM;
> +
> +	/* Get UTMI memory region */
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	if (!res) {
> +		dev_err(dev, "Missing UTMI PHY memory resource\n");
> +		return -ENODEV;
> +	}
> +
> +	utmi->regs = devm_ioremap_resource(dev, res);
> +	if (IS_ERR(utmi->regs))
> +		return PTR_ERR(utmi->regs);
> +
> +	/* Get miscellaneous Host/PHY region */
> +	utmi->usb_misc = syscon_regmap_lookup_by_phandle(dev->of_node,
> +							 "marvell,usb-misc-reg");
> +	if (IS_ERR(utmi->usb_misc)) {
> +		dev_err(dev,
> +			"Missing USB misc purpose system controller\n");
> +		return PTR_ERR(utmi->usb_misc);
> +	}
> +
> +	/* Retrieve PHY capabilities */
> +	dev_id = of_match_device(mvebu_a3700_utmi_of_match, dev);
> +	if (!dev_id)
> +		return -EINVAL;
> +
> +	utmi->caps = dev_id->data;
a useful API to get @data: of_device_get_match_data()

> +	ops = utmi->caps->ops;
> +
> +	/* Instantiate the PHY */
> +	utmi->phy = devm_phy_create(dev, NULL, ops);
> +	if (IS_ERR(utmi->phy)) {
> +		dev_err(dev, "Failed to create the UTMI PHY\n");
> +		return PTR_ERR(utmi->phy);
> +	}
> +
> +	phy_set_drvdata(utmi->phy, utmi);
> +
> +	/* Ensure the PHY is powered off */
> +	ops->power_off(utmi->phy);
> +
> +	provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> +
> +	return PTR_ERR_OR_ZERO(provider);
> +}
> +
> +static int mvebu_a3700_utmi_phy_remove(struct platform_device *pdev)
> +{
> +	return 0;
> +}
> +
> +static struct platform_driver mvebu_a3700_utmi_driver = {
> +	.probe	= mvebu_a3700_utmi_phy_probe,
> +	.remove = mvebu_a3700_utmi_phy_remove,
> +	.driver	= {
> +		.name		= "mvebu-a3700-utmi-phy",
> +		.owner		= THIS_MODULE,
> +		.of_match_table	= mvebu_a3700_utmi_of_match,
> +	 },
> +};
> +module_platform_driver(mvebu_a3700_utmi_driver);
> +
> +MODULE_AUTHOR("Evan Wang <xswang@marvell.com>");
> +MODULE_AUTHOR("Miquel Raynal <miquel.raynal@bootlin.com>");
> +MODULE_DESCRIPTION("Marvell EBU A3700 UTMI PHY driver");
> +MODULE_LICENSE("GPL");
Kishon Vijay Abraham I Jan. 16, 2019, 9:20 a.m. UTC | #2 
Hi,

On 15/01/19 8:10 AM, Chunfeng Yun wrote:
> Hi,
> On Fri, 2019-01-11 at 14:31 +0100, Miquel Raynal wrote:
>> Marvell Armada 3700 SoC has two USB controllers, each of them being
>> wired to an internal UTMI PHY. Add a driver to control them.
>>
>> Igal Liberman worked on supporting the PHY, I took the while 'register
>> configuration' from his work and rewrote almost entirely the
>> driver/bindings around it.
>>
>> Co-developed-by: Igal Liberman <igall@marvell.com>
>> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
>> Signed-off-by: Igal Liberman <igall@marvell.com>
>> ---
>>  drivers/phy/marvell/Kconfig                |   9 +
>>  drivers/phy/marvell/Makefile               |   1 +
>>  drivers/phy/marvell/phy-mvebu-a3700-utmi.c | 297 +++++++++++++++++++++
>>  3 files changed, 307 insertions(+)
>>  create mode 100644 drivers/phy/marvell/phy-mvebu-a3700-utmi.c
>>
>> diff --git a/drivers/phy/marvell/Kconfig b/drivers/phy/marvell/Kconfig
>> index 9c90c0408ea3..b8e9dd38ad0d 100644
>> --- a/drivers/phy/marvell/Kconfig
>> +++ b/drivers/phy/marvell/Kconfig
>> @@ -33,6 +33,15 @@ config PHY_MVEBU_A3700_COMPHY
>>  	  shared serdes PHYs on Marvell Armada 3700. Its serdes lanes can be
>>  	  used by various controllers: Ethernet, SATA, USB3, PCIe.
>>  
>> +config PHY_MVEBU_A3700_UTMI
>> +	tristate "Marvell A3700 UTMI driver"
>> +	depends on ARCH_MVEBU || COMPILE_TEST
>> +	depends on OF
>> +	default y
>> +	select GENERIC_PHY
>> +	help
>> +	  Enable this to support Marvell A3700 UTMI PHY driver.
>> +
>>  config PHY_MVEBU_CP110_COMPHY
>>  	tristate "Marvell CP110 comphy driver"
>>  	depends on ARCH_MVEBU || COMPILE_TEST
>> diff --git a/drivers/phy/marvell/Makefile b/drivers/phy/marvell/Makefile
>> index c13a0c8ab6f0..82f291cf59ee 100644
>> --- a/drivers/phy/marvell/Makefile
>> +++ b/drivers/phy/marvell/Makefile
>> @@ -3,6 +3,7 @@ obj-$(CONFIG_ARMADA375_USBCLUSTER_PHY)	+= phy-armada375-usb2.o
>>  obj-$(CONFIG_PHY_BERLIN_SATA)		+= phy-berlin-sata.o
>>  obj-$(CONFIG_PHY_BERLIN_USB)		+= phy-berlin-usb.o
>>  obj-$(CONFIG_PHY_MVEBU_A3700_COMPHY)	+= phy-mvebu-a3700-comphy.o
>> +obj-$(CONFIG_PHY_MVEBU_A3700_UTMI)	+= phy-mvebu-a3700-utmi.o
>>  obj-$(CONFIG_PHY_MVEBU_CP110_COMPHY)	+= phy-mvebu-cp110-comphy.o
>>  obj-$(CONFIG_PHY_MVEBU_SATA)		+= phy-mvebu-sata.o
>>  obj-$(CONFIG_PHY_PXA_28NM_HSIC)		+= phy-pxa-28nm-hsic.o
>> diff --git a/drivers/phy/marvell/phy-mvebu-a3700-utmi.c b/drivers/phy/marvell/phy-mvebu-a3700-utmi.c
>> new file mode 100644
>> index 000000000000..97d8235d661d
>> --- /dev/null
>> +++ b/drivers/phy/marvell/phy-mvebu-a3700-utmi.c
>> @@ -0,0 +1,297 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Copyright (C) 2018 Marvell
>> + *
>> + * Authors:
>> + *   Evan Wang <xswang@marvell.com>
>> + *   Miquèl Raynal <miquel.raynal@bootlin.com>
>> + *
>> + * Marvell A3700 UTMI PHY driver
>> + */
>> +
>> +#include <linux/io.h>
>> +#include <linux/iopoll.h>
>> +#include <linux/mfd/syscon.h>
>> +#include <linux/module.h>
>> +#include <linux/of_device.h>
>> +#include <linux/phy/phy.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/regmap.h>
>> +
>> +/* Armada 3700 UTMI PHY registers */
>> +#define USB2_PHY_PLL_CTRL_REG0			0x0
>> +#define   PLL_REF_DIV_OFF			0
>> +#define   PLL_REF_DIV_MASK			(0x7F << PLL_REF_DIV_OFF)
> use GENMASK?
>> +#define   PLL_REF_DIV_5				0x5
>> +#define   PLL_FB_DIV_OFF			16
>> +#define   PLL_FB_DIV_MASK			(0x1FF << PLL_FB_DIV_OFF)
>> +#define   PLL_FB_DIV_96				96
>> +#define   PLL_SEL_LPFR_OFF			28
>> +#define   PLL_SEL_LPFR_MASK			(0x3 << PLL_SEL_LPFR_OFF)
>> +#define   PLL_READY				BIT(31)
>> +#define USB2_PHY_CAL_CTRL			0x8
>> +#define   PHY_PLLCAL_DONE			BIT(31)
>> +#define   PHY_IMPCAL_DONE			BIT(23)
>> +#define USB2_RX_CHAN_CTRL1			0x18
>> +#define   USB2PHY_SQCAL_DONE			BIT(31)
>> +#define USB2_PHY_OTG_CTRL			0x34
>> +#define   PHY_PU_OTG				BIT(4)
>> +#define USB2_PHY_CHRGR_DETECT			0x38
>> +#define   PHY_CDP_EN				BIT(2)
>> +#define   PHY_DCP_EN				BIT(3)
>> +#define   PHY_PD_EN				BIT(4)
>> +#define   PHY_PU_CHRG_DTC			BIT(5)
>> +#define   PHY_CDP_DM_AUTO			BIT(7)
>> +#define   PHY_ENSWITCH_DP			BIT(12)
>> +#define   PHY_ENSWITCH_DM			BIT(13)
>> +
>> +/* Armada 3700 USB miscellaneous registers */
>> +#define USB2_PHY_CTRL(usb32)			(usb32 ? 0x20 : 0x4)
>> +#define   RB_USB2PHY_PU				BIT(0)
>> +#define   USB2_DP_PULLDN_DEV_MODE		BIT(5)
>> +#define   USB2_DM_PULLDN_DEV_MODE		BIT(6)
>> +#define   RB_USB2PHY_SUSPM(usb32)		(usb32 ? BIT(14) : BIT(7))
>> +
>> +#define PLL_LOCK_DELAY_US			10000
>> +#define PLL_LOCK_TIMEOUT_US			1000000
>> +
>> +/**
>> + * struct mvebu_a3700_utmi_caps - PHY capabilities
>> + *
>> + * @usb32: Flag indicating which PHY is in use (impacts the register map):
>> + *           - The UTMI PHY wired to the USB3/USB2 controller (otg)
>> + *           - The UTMI PHY wired to the USB2 controller (host only)
>> + * @ops: PHY operations
>> + */
>> +struct mvebu_a3700_utmi_caps {
>> +	int usb32;
>> +	const struct phy_ops *ops;
>> +};
>> +
>> +/**
>> + * struct mvebu_a3700_utmi - PHY driver data
>> + *
>> + * @regs: PHY registers
>> + * @usb_mis: Regmap with USB miscellaneous registers including PHY ones
>> + * @caps: PHY capabilities
>> + * @phy: PHY handle
>> + */
>> +struct mvebu_a3700_utmi {
>> +	void __iomem *regs;
>> +	struct regmap *usb_misc;
>> +	const struct mvebu_a3700_utmi_caps *caps;
>> +	struct phy *phy;
>> +};
>> +
>> +static int mvebu_a3700_utmi_phy_power_on(struct phy *phy)
>> +{
>> +	struct mvebu_a3700_utmi *utmi = phy_get_drvdata(phy);
>> +	struct device *dev = &phy->dev;
>> +	int usb32 = utmi->caps->usb32;
>> +	int ret = 0;
>> +	u32 reg;
>> +
>> +	if (!utmi)
>> +		return -ENODEV;
> the check here may be not necessary

right. utmi is already referenced above.
>> +
>> +	/*
>> +	 * Setup PLL. 40MHz clock used to be the default, bein 25MHz now.
>> +	 * See "PLL Settings for Typical REFCLK" table.
>> +	 */
>> +	reg = readl(utmi->regs + USB2_PHY_PLL_CTRL_REG0);
>> +	reg &= ~(PLL_REF_DIV_MASK | PLL_FB_DIV_MASK | PLL_SEL_LPFR_MASK);
>> +	reg |= (PLL_REF_DIV_5 << PLL_REF_DIV_OFF |
>> +		PLL_FB_DIV_96 << PLL_FB_DIV_OFF);
>> +	writel(reg, utmi->regs + USB2_PHY_PLL_CTRL_REG0);
>> +
>> +	/* Enable PHY pull up and disable USB2 suspend */
>> +	regmap_update_bits(utmi->usb_misc, USB2_PHY_CTRL(usb32),
>> +			   RB_USB2PHY_SUSPM(usb32) | RB_USB2PHY_PU,
>> +			   RB_USB2PHY_SUSPM(usb32) | RB_USB2PHY_PU);
>> +
>> +	if (usb32) {
>> +		/* Power up OTG module */
>> +		reg = readl(utmi->regs + USB2_PHY_OTG_CTRL);
>> +		reg |= PHY_PU_OTG;
>> +		writel(reg, utmi->regs + USB2_PHY_OTG_CTRL);
>> +
>> +		/* Disable PHY charger detection */
>> +		reg = readl(utmi->regs + USB2_PHY_CHRGR_DETECT);
>> +		reg &= ~(PHY_CDP_EN | PHY_DCP_EN | PHY_PD_EN | PHY_PU_CHRG_DTC |
>> +			 PHY_CDP_DM_AUTO | PHY_ENSWITCH_DP | PHY_ENSWITCH_DM);
>> +		writel(reg, utmi->regs + USB2_PHY_CHRGR_DETECT);
>> +
>> +		/* Disable PHY DP/DM pull-down (used for device mode) */
>> +		regmap_update_bits(utmi->usb_misc, USB2_PHY_CTRL(usb32),
>> +				   USB2_DP_PULLDN_DEV_MODE |
>> +				   USB2_DM_PULLDN_DEV_MODE, 0);
>> +	}
>> +
>> +	/* Wait for PLL calibration */
>> +	ret = readl_poll_timeout(utmi->regs + USB2_PHY_CAL_CTRL, reg,
>> +				 reg & PHY_PLLCAL_DONE,
>> +				 PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
>> +	if (ret) {
>> +		dev_err(dev, "Failed to end USB2 PLL calibration\n");
>> +		return ret;
>> +	}
>> +
>> +	/* Wait for impedance calibration */
>> +	ret = readl_poll_timeout(utmi->regs + USB2_PHY_CAL_CTRL, reg,
>> +				 reg & PHY_IMPCAL_DONE,
>> +				 PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
>> +	if (ret) {
>> +		dev_err(dev, "Failed to end USB2 impedance calibration\n");
>> +		return ret;
>> +	}
>> +
>> +	/* Wait for squetch calibration */
>> +	ret = readl_poll_timeout(utmi->regs + USB2_RX_CHAN_CTRL1, reg,
>> +				 reg & USB2PHY_SQCAL_DONE,
>> +				 PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
>> +	if (ret) {
>> +		dev_err(dev, "Failed to end USB2 unknown calibration\n");
>> +		return ret;
>> +	}
>> +
>> +	/* Wait for PLL to be locked */
>> +	ret = readl_poll_timeout(utmi->regs + USB2_PHY_PLL_CTRL_REG0, reg,
>> +				 reg & PLL_READY,
>> +				 PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
>> +	if (ret)
>> +		dev_err(dev, "Failed to lock USB2 PLL\n");
>> +
>> +	return ret;
>> +}
>> +
>> +static int mvebu_a3700_utmi_phy_power_off(struct phy *phy)
>> +{
>> +	struct mvebu_a3700_utmi *utmi = phy_get_drvdata(phy);
>> +	int usb32 = utmi->caps->usb32;
>> +	u32 reg;
>> +
>> +	if (!utmi)
>> +		return -ENODEV;

here too, utmi is referenced above.
>> +
>> +	/* Disable PHY pull-up and enable USB2 suspend */
>> +	reg = readl(utmi->regs + USB2_PHY_CTRL(usb32));
>> +	reg &= ~(RB_USB2PHY_PU | RB_USB2PHY_SUSPM(usb32));
>> +	writel(reg, utmi->regs + USB2_PHY_CTRL(usb32));
>> +
>> +	/* Power down OTG module */
>> +	if (usb32) {
>> +		reg = readl(utmi->regs + USB2_PHY_OTG_CTRL);
>> +		reg &= ~PHY_PU_OTG;
>> +		writel(reg, utmi->regs + USB2_PHY_OTG_CTRL);
>> +	}
>> +
>> +	return 0;
>> +}
>> +
>> +static const struct phy_ops mvebu_a3700_utmi_phy_ops = {
>> +	.power_on = mvebu_a3700_utmi_phy_power_on,
>> +	.power_off = mvebu_a3700_utmi_phy_power_off,
>> +	.owner = THIS_MODULE,
>> +};
>> +
>> +static const struct mvebu_a3700_utmi_caps mvebu_a3700_utmi_otg_phy_caps = {
>> +	.usb32 = true,
>> +	.ops = &mvebu_a3700_utmi_phy_ops,
>> +};
>> +
>> +static const struct mvebu_a3700_utmi_caps mvebu_a3700_utmi_host_phy_caps = {
>> +	.usb32 = false,
>> +	.ops = &mvebu_a3700_utmi_phy_ops,
>> +};
>> +
>> +static const struct of_device_id mvebu_a3700_utmi_of_match[] = {
>> +	{
>> +		.compatible = "marvell,a3700-utmi-otg-phy",
>> +		.data = &mvebu_a3700_utmi_otg_phy_caps,
>> +	},
>> +	{
>> +		.compatible = "marvell,a3700-utmi-host-phy",
>> +		.data = &mvebu_a3700_utmi_host_phy_caps,
>> +	},
>> +	{},
>> +};
>> +MODULE_DEVICE_TABLE(of, mvebu_a3700_utmi_of_match);
>> +
>> +static int mvebu_a3700_utmi_phy_probe(struct platform_device *pdev)
>> +{
>> +	const struct of_device_id *dev_id;
>> +	struct device *dev = &pdev->dev;
>> +	struct mvebu_a3700_utmi *utmi;
>> +	struct phy_provider *provider;
>> +	const struct phy_ops *ops;
>> +	struct resource *res;
>> +
>> +	utmi = devm_kzalloc(dev, sizeof(*utmi), GFP_KERNEL);
>> +	if (!utmi)
>> +		return -ENOMEM;
>> +
>> +	/* Get UTMI memory region */
>> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> +	if (!res) {
>> +		dev_err(dev, "Missing UTMI PHY memory resource\n");
>> +		return -ENODEV;
>> +	}
>> +
>> +	utmi->regs = devm_ioremap_resource(dev, res);
>> +	if (IS_ERR(utmi->regs))
>> +		return PTR_ERR(utmi->regs);
>> +
>> +	/* Get miscellaneous Host/PHY region */
>> +	utmi->usb_misc = syscon_regmap_lookup_by_phandle(dev->of_node,
>> +							 "marvell,usb-misc-reg");
>> +	if (IS_ERR(utmi->usb_misc)) {
>> +		dev_err(dev,
>> +			"Missing USB misc purpose system controller\n");
>> +		return PTR_ERR(utmi->usb_misc);
>> +	}
>> +
>> +	/* Retrieve PHY capabilities */
>> +	dev_id = of_match_device(mvebu_a3700_utmi_of_match, dev);
>> +	if (!dev_id)
>> +		return -EINVAL;
>> +
>> +	utmi->caps = dev_id->data;
> a useful API to get @data: of_device_get_match_data()
> 
>> +	ops = utmi->caps->ops;
>> +
>> +	/* Instantiate the PHY */
>> +	utmi->phy = devm_phy_create(dev, NULL, ops);
>> +	if (IS_ERR(utmi->phy)) {
>> +		dev_err(dev, "Failed to create the UTMI PHY\n");
>> +		return PTR_ERR(utmi->phy);
>> +	}
>> +
>> +	phy_set_drvdata(utmi->phy, utmi);
>> +
>> +	/* Ensure the PHY is powered off */
>> +	ops->power_off(utmi->phy);
>> +
>> +	provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
>> +
>> +	return PTR_ERR_OR_ZERO(provider);
>> +}
>> +
>> +static int mvebu_a3700_utmi_phy_remove(struct platform_device *pdev)
>> +{
>> +	return 0;
>> +}

This empty remove function can be removed.

Thanks
Kishon

>> +
>> +static struct platform_driver mvebu_a3700_utmi_driver = {
>> +	.probe	= mvebu_a3700_utmi_phy_probe,
>> +	.remove = mvebu_a3700_utmi_phy_remove,
>> +	.driver	= {
>> +		.name		= "mvebu-a3700-utmi-phy",
>> +		.owner		= THIS_MODULE,
>> +		.of_match_table	= mvebu_a3700_utmi_of_match,
>> +	 },
>> +};
>> +module_platform_driver(mvebu_a3700_utmi_driver);
>> +
>> +MODULE_AUTHOR("Evan Wang <xswang@marvell.com>");
>> +MODULE_AUTHOR("Miquel Raynal <miquel.raynal@bootlin.com>");
>> +MODULE_DESCRIPTION("Marvell EBU A3700 UTMI PHY driver");
>> +MODULE_LICENSE("GPL");
> 
>
Gregory CLEMENT Jan. 18, 2019, 4:36 p.m. UTC | #3 
Hi Miquel,

I have only a few smallish remarks:

 On ven., janv. 11 2019, Miquel Raynal <miquel.raynal@bootlin.com> wrote:

> Marvell Armada 3700 SoC has two USB controllers, each of them being
> wired to an internal UTMI PHY. Add a driver to control them.
>
> Igal Liberman worked on supporting the PHY, I took the while 'register
> configuration' from his work and rewrote almost entirely the
> driver/bindings around it.
>
> Co-developed-by: Igal Liberman <igall@marvell.com>
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> Signed-off-by: Igal Liberman <igall@marvell.com>
> ---
[...]

> diff --git a/drivers/phy/marvell/phy-mvebu-a3700-utmi.c b/drivers/phy/marvell/phy-mvebu-a3700-utmi.c
> new file mode 100644
> index 000000000000..97d8235d661d
> --- /dev/null
> +++ b/drivers/phy/marvell/phy-mvebu-a3700-utmi.c
> @@ -0,0 +1,297 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2018 Marvell
> + *
> + * Authors:
> + *   Evan Wang <xswang@marvell.com>
> + *   Miquèl Raynal <miquel.raynal@bootlin.com>

If it is co-developed with Igal Liberman, shouldn't be added here too?
[...]

> +static int mvebu_a3700_utmi_phy_power_on(struct phy *phy)
> +{
> +	struct mvebu_a3700_utmi *utmi = phy_get_drvdata(phy);
> +	struct device *dev = &phy->dev;
> +	int usb32 = utmi->caps->usb32;
> +	int ret = 0;
> +	u32 reg;
> +
> +	if (!utmi)
> +		return -ENODEV;
> +
> +	/*
> +	 * Setup PLL. 40MHz clock used to be the default, bein 25MHz now.
                                                          bein?
> +	 * See "PLL Settings for Typical REFCLK" table.

[...]

> +
> +	/* Wait for squetch calibration */
                    squetch?

Gregory
Miquel Raynal Jan. 21, 2019, 10:24 a.m. UTC | #4 
Hi Gregory,

Gregory CLEMENT <gregory.clement@bootlin.com> wrote on Fri, 18 Jan 2019
17:36:36 +0100:

> Hi Miquel,
> 
> I have only a few smallish remarks:
> 
>  On ven., janv. 11 2019, Miquel Raynal <miquel.raynal@bootlin.com> wrote:
> 
> > Marvell Armada 3700 SoC has two USB controllers, each of them being
> > wired to an internal UTMI PHY. Add a driver to control them.
> >
> > Igal Liberman worked on supporting the PHY, I took the while 'register
> > configuration' from his work and rewrote almost entirely the
> > driver/bindings around it.
> >
> > Co-developed-by: Igal Liberman <igall@marvell.com>
> > Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> > Signed-off-by: Igal Liberman <igall@marvell.com>
> > ---  
> [...]
> 
> > diff --git a/drivers/phy/marvell/phy-mvebu-a3700-utmi.c b/drivers/phy/marvell/phy-mvebu-a3700-utmi.c
> > new file mode 100644
> > index 000000000000..97d8235d661d
> > --- /dev/null
> > +++ b/drivers/phy/marvell/phy-mvebu-a3700-utmi.c
> > @@ -0,0 +1,297 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Copyright (C) 2018 Marvell
> > + *
> > + * Authors:
> > + *   Evan Wang <xswang@marvell.com>
> > + *   Miquèl Raynal <miquel.raynal@bootlin.com>  
> 
> If it is co-developed with Igal Liberman, shouldn't be added here too?

In the original patch, the author in the commit log was Igal and the
MODULE_AUTHOR macro was saying Evan. I think the macro is wrong, I will
keep Igal.

> [...]
> 
> > +static int mvebu_a3700_utmi_phy_power_on(struct phy *phy)
> > +{
> > +	struct mvebu_a3700_utmi *utmi = phy_get_drvdata(phy);
> > +	struct device *dev = &phy->dev;
> > +	int usb32 = utmi->caps->usb32;
> > +	int ret = 0;
> > +	u32 reg;
> > +
> > +	if (!utmi)
> > +		return -ENODEV;
> > +
> > +	/*
> > +	 * Setup PLL. 40MHz clock used to be the default, bein 25MHz now.  
>                                                           bein?
> > +	 * See "PLL Settings for Typical REFCLK" table.  
> 
> [...]
> 
> > +
> > +	/* Wait for squetch calibration */  
>                     squetch?

Good catch. It's written "squelch" in the datasheet, but I don't know
what it means exactly.


Thanks,
Miquèl
Miquel Raynal Jan. 21, 2019, 10:37 a.m. UTC | #5 
Hi Kishon, Chunfeng,

Kishon Vijay Abraham I <kishon@ti.com> wrote on Wed, 16 Jan 2019
14:50:58 +0530:

> Hi,
> 
> On 15/01/19 8:10 AM, Chunfeng Yun wrote:
> > Hi,
> > On Fri, 2019-01-11 at 14:31 +0100, Miquel Raynal wrote:  
> >> Marvell Armada 3700 SoC has two USB controllers, each of them being
> >> wired to an internal UTMI PHY. Add a driver to control them.
> >>
> >> Igal Liberman worked on supporting the PHY, I took the while 'register
> >> configuration' from his work and rewrote almost entirely the
> >> driver/bindings around it.
> >>
> >> Co-developed-by: Igal Liberman <igall@marvell.com>
> >> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> >> Signed-off-by: Igal Liberman <igall@marvell.com>
> >> ---
> >>  drivers/phy/marvell/Kconfig                |   9 +
> >>  drivers/phy/marvell/Makefile               |   1 +
> >>  drivers/phy/marvell/phy-mvebu-a3700-utmi.c | 297 +++++++++++++++++++++
> >>  3 files changed, 307 insertions(+)
> >>  create mode 100644 drivers/phy/marvell/phy-mvebu-a3700-utmi.c
> >>
> >> diff --git a/drivers/phy/marvell/Kconfig b/drivers/phy/marvell/Kconfig
> >> index 9c90c0408ea3..b8e9dd38ad0d 100644
> >> --- a/drivers/phy/marvell/Kconfig
> >> +++ b/drivers/phy/marvell/Kconfig
> >> @@ -33,6 +33,15 @@ config PHY_MVEBU_A3700_COMPHY
> >>  	  shared serdes PHYs on Marvell Armada 3700. Its serdes lanes can be
> >>  	  used by various controllers: Ethernet, SATA, USB3, PCIe.
> >>  
> >> +config PHY_MVEBU_A3700_UTMI
> >> +	tristate "Marvell A3700 UTMI driver"
> >> +	depends on ARCH_MVEBU || COMPILE_TEST
> >> +	depends on OF
> >> +	default y
> >> +	select GENERIC_PHY
> >> +	help
> >> +	  Enable this to support Marvell A3700 UTMI PHY driver.
> >> +
> >>  config PHY_MVEBU_CP110_COMPHY
> >>  	tristate "Marvell CP110 comphy driver"
> >>  	depends on ARCH_MVEBU || COMPILE_TEST
> >> diff --git a/drivers/phy/marvell/Makefile b/drivers/phy/marvell/Makefile
> >> index c13a0c8ab6f0..82f291cf59ee 100644
> >> --- a/drivers/phy/marvell/Makefile
> >> +++ b/drivers/phy/marvell/Makefile
> >> @@ -3,6 +3,7 @@ obj-$(CONFIG_ARMADA375_USBCLUSTER_PHY)	+= phy-armada375-usb2.o
> >>  obj-$(CONFIG_PHY_BERLIN_SATA)		+= phy-berlin-sata.o
> >>  obj-$(CONFIG_PHY_BERLIN_USB)		+= phy-berlin-usb.o
> >>  obj-$(CONFIG_PHY_MVEBU_A3700_COMPHY)	+= phy-mvebu-a3700-comphy.o
> >> +obj-$(CONFIG_PHY_MVEBU_A3700_UTMI)	+= phy-mvebu-a3700-utmi.o
> >>  obj-$(CONFIG_PHY_MVEBU_CP110_COMPHY)	+= phy-mvebu-cp110-comphy.o
> >>  obj-$(CONFIG_PHY_MVEBU_SATA)		+= phy-mvebu-sata.o
> >>  obj-$(CONFIG_PHY_PXA_28NM_HSIC)		+= phy-pxa-28nm-hsic.o
> >> diff --git a/drivers/phy/marvell/phy-mvebu-a3700-utmi.c b/drivers/phy/marvell/phy-mvebu-a3700-utmi.c
> >> new file mode 100644
> >> index 000000000000..97d8235d661d
> >> --- /dev/null
> >> +++ b/drivers/phy/marvell/phy-mvebu-a3700-utmi.c
> >> @@ -0,0 +1,297 @@
> >> +// SPDX-License-Identifier: GPL-2.0
> >> +/*
> >> + * Copyright (C) 2018 Marvell
> >> + *
> >> + * Authors:
> >> + *   Evan Wang <xswang@marvell.com>
> >> + *   Miquèl Raynal <miquel.raynal@bootlin.com>
> >> + *
> >> + * Marvell A3700 UTMI PHY driver
> >> + */
> >> +
> >> +#include <linux/io.h>
> >> +#include <linux/iopoll.h>
> >> +#include <linux/mfd/syscon.h>
> >> +#include <linux/module.h>
> >> +#include <linux/of_device.h>
> >> +#include <linux/phy/phy.h>
> >> +#include <linux/platform_device.h>
> >> +#include <linux/regmap.h>
> >> +
> >> +/* Armada 3700 UTMI PHY registers */
> >> +#define USB2_PHY_PLL_CTRL_REG0			0x0
> >> +#define   PLL_REF_DIV_OFF			0
> >> +#define   PLL_REF_DIV_MASK			(0x7F << PLL_REF_DIV_OFF)  
> > use GENMASK?  

Ok

> >> +#define   PLL_REF_DIV_5				0x5
> >> +#define   PLL_FB_DIV_OFF			16
> >> +#define   PLL_FB_DIV_MASK			(0x1FF << PLL_FB_DIV_OFF)
> >> +#define   PLL_FB_DIV_96				96
> >> +#define   PLL_SEL_LPFR_OFF			28
> >> +#define   PLL_SEL_LPFR_MASK			(0x3 << PLL_SEL_LPFR_OFF)
> >> +#define   PLL_READY				BIT(31)
> >> +#define USB2_PHY_CAL_CTRL			0x8
> >> +#define   PHY_PLLCAL_DONE			BIT(31)
> >> +#define   PHY_IMPCAL_DONE			BIT(23)
> >> +#define USB2_RX_CHAN_CTRL1			0x18
> >> +#define   USB2PHY_SQCAL_DONE			BIT(31)
> >> +#define USB2_PHY_OTG_CTRL			0x34
> >> +#define   PHY_PU_OTG				BIT(4)
> >> +#define USB2_PHY_CHRGR_DETECT			0x38
> >> +#define   PHY_CDP_EN				BIT(2)
> >> +#define   PHY_DCP_EN				BIT(3)
> >> +#define   PHY_PD_EN				BIT(4)
> >> +#define   PHY_PU_CHRG_DTC			BIT(5)
> >> +#define   PHY_CDP_DM_AUTO			BIT(7)
> >> +#define   PHY_ENSWITCH_DP			BIT(12)
> >> +#define   PHY_ENSWITCH_DM			BIT(13)
> >> +
> >> +/* Armada 3700 USB miscellaneous registers */
> >> +#define USB2_PHY_CTRL(usb32)			(usb32 ? 0x20 : 0x4)
> >> +#define   RB_USB2PHY_PU				BIT(0)
> >> +#define   USB2_DP_PULLDN_DEV_MODE		BIT(5)
> >> +#define   USB2_DM_PULLDN_DEV_MODE		BIT(6)
> >> +#define   RB_USB2PHY_SUSPM(usb32)		(usb32 ? BIT(14) : BIT(7))
> >> +
> >> +#define PLL_LOCK_DELAY_US			10000
> >> +#define PLL_LOCK_TIMEOUT_US			1000000
> >> +
> >> +/**
> >> + * struct mvebu_a3700_utmi_caps - PHY capabilities
> >> + *
> >> + * @usb32: Flag indicating which PHY is in use (impacts the register map):
> >> + *           - The UTMI PHY wired to the USB3/USB2 controller (otg)
> >> + *           - The UTMI PHY wired to the USB2 controller (host only)
> >> + * @ops: PHY operations
> >> + */
> >> +struct mvebu_a3700_utmi_caps {
> >> +	int usb32;
> >> +	const struct phy_ops *ops;
> >> +};
> >> +
> >> +/**
> >> + * struct mvebu_a3700_utmi - PHY driver data
> >> + *
> >> + * @regs: PHY registers
> >> + * @usb_mis: Regmap with USB miscellaneous registers including PHY ones
> >> + * @caps: PHY capabilities
> >> + * @phy: PHY handle
> >> + */
> >> +struct mvebu_a3700_utmi {
> >> +	void __iomem *regs;
> >> +	struct regmap *usb_misc;
> >> +	const struct mvebu_a3700_utmi_caps *caps;
> >> +	struct phy *phy;
> >> +};
> >> +
> >> +static int mvebu_a3700_utmi_phy_power_on(struct phy *phy)
> >> +{
> >> +	struct mvebu_a3700_utmi *utmi = phy_get_drvdata(phy);
> >> +	struct device *dev = &phy->dev;
> >> +	int usb32 = utmi->caps->usb32;
> >> +	int ret = 0;
> >> +	u32 reg;
> >> +
> >> +	if (!utmi)
> >> +		return -ENODEV;  
> > the check here may be not necessary  
> 
> right. utmi is already referenced above.

Removed.

> >> +
> >> +	/*
> >> +	 * Setup PLL. 40MHz clock used to be the default, bein 25MHz now.
> >> +	 * See "PLL Settings for Typical REFCLK" table.
> >> +	 */
> >> +	reg = readl(utmi->regs + USB2_PHY_PLL_CTRL_REG0);
> >> +	reg &= ~(PLL_REF_DIV_MASK | PLL_FB_DIV_MASK | PLL_SEL_LPFR_MASK);
> >> +	reg |= (PLL_REF_DIV_5 << PLL_REF_DIV_OFF |
> >> +		PLL_FB_DIV_96 << PLL_FB_DIV_OFF);
> >> +	writel(reg, utmi->regs + USB2_PHY_PLL_CTRL_REG0);
> >> +
> >> +	/* Enable PHY pull up and disable USB2 suspend */
> >> +	regmap_update_bits(utmi->usb_misc, USB2_PHY_CTRL(usb32),
> >> +			   RB_USB2PHY_SUSPM(usb32) | RB_USB2PHY_PU,
> >> +			   RB_USB2PHY_SUSPM(usb32) | RB_USB2PHY_PU);
> >> +
> >> +	if (usb32) {
> >> +		/* Power up OTG module */
> >> +		reg = readl(utmi->regs + USB2_PHY_OTG_CTRL);
> >> +		reg |= PHY_PU_OTG;
> >> +		writel(reg, utmi->regs + USB2_PHY_OTG_CTRL);
> >> +
> >> +		/* Disable PHY charger detection */
> >> +		reg = readl(utmi->regs + USB2_PHY_CHRGR_DETECT);
> >> +		reg &= ~(PHY_CDP_EN | PHY_DCP_EN | PHY_PD_EN | PHY_PU_CHRG_DTC |
> >> +			 PHY_CDP_DM_AUTO | PHY_ENSWITCH_DP | PHY_ENSWITCH_DM);
> >> +		writel(reg, utmi->regs + USB2_PHY_CHRGR_DETECT);
> >> +
> >> +		/* Disable PHY DP/DM pull-down (used for device mode) */
> >> +		regmap_update_bits(utmi->usb_misc, USB2_PHY_CTRL(usb32),
> >> +				   USB2_DP_PULLDN_DEV_MODE |
> >> +				   USB2_DM_PULLDN_DEV_MODE, 0);
> >> +	}
> >> +
> >> +	/* Wait for PLL calibration */
> >> +	ret = readl_poll_timeout(utmi->regs + USB2_PHY_CAL_CTRL, reg,
> >> +				 reg & PHY_PLLCAL_DONE,
> >> +				 PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
> >> +	if (ret) {
> >> +		dev_err(dev, "Failed to end USB2 PLL calibration\n");
> >> +		return ret;
> >> +	}
> >> +
> >> +	/* Wait for impedance calibration */
> >> +	ret = readl_poll_timeout(utmi->regs + USB2_PHY_CAL_CTRL, reg,
> >> +				 reg & PHY_IMPCAL_DONE,
> >> +				 PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
> >> +	if (ret) {
> >> +		dev_err(dev, "Failed to end USB2 impedance calibration\n");
> >> +		return ret;
> >> +	}
> >> +
> >> +	/* Wait for squetch calibration */
> >> +	ret = readl_poll_timeout(utmi->regs + USB2_RX_CHAN_CTRL1, reg,
> >> +				 reg & USB2PHY_SQCAL_DONE,
> >> +				 PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
> >> +	if (ret) {
> >> +		dev_err(dev, "Failed to end USB2 unknown calibration\n");
> >> +		return ret;
> >> +	}
> >> +
> >> +	/* Wait for PLL to be locked */
> >> +	ret = readl_poll_timeout(utmi->regs + USB2_PHY_PLL_CTRL_REG0, reg,
> >> +				 reg & PLL_READY,
> >> +				 PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
> >> +	if (ret)
> >> +		dev_err(dev, "Failed to lock USB2 PLL\n");
> >> +
> >> +	return ret;
> >> +}
> >> +
> >> +static int mvebu_a3700_utmi_phy_power_off(struct phy *phy)
> >> +{
> >> +	struct mvebu_a3700_utmi *utmi = phy_get_drvdata(phy);
> >> +	int usb32 = utmi->caps->usb32;
> >> +	u32 reg;
> >> +
> >> +	if (!utmi)
> >> +		return -ENODEV;  
> 
> here too, utmi is referenced above.

Removed too.

> >> +
> >> +	/* Disable PHY pull-up and enable USB2 suspend */
> >> +	reg = readl(utmi->regs + USB2_PHY_CTRL(usb32));
> >> +	reg &= ~(RB_USB2PHY_PU | RB_USB2PHY_SUSPM(usb32));
> >> +	writel(reg, utmi->regs + USB2_PHY_CTRL(usb32));
> >> +
> >> +	/* Power down OTG module */
> >> +	if (usb32) {
> >> +		reg = readl(utmi->regs + USB2_PHY_OTG_CTRL);
> >> +		reg &= ~PHY_PU_OTG;
> >> +		writel(reg, utmi->regs + USB2_PHY_OTG_CTRL);
> >> +	}
> >> +
> >> +	return 0;
> >> +}
> >> +
> >> +static const struct phy_ops mvebu_a3700_utmi_phy_ops = {
> >> +	.power_on = mvebu_a3700_utmi_phy_power_on,
> >> +	.power_off = mvebu_a3700_utmi_phy_power_off,
> >> +	.owner = THIS_MODULE,
> >> +};
> >> +
> >> +static const struct mvebu_a3700_utmi_caps mvebu_a3700_utmi_otg_phy_caps = {
> >> +	.usb32 = true,
> >> +	.ops = &mvebu_a3700_utmi_phy_ops,
> >> +};
> >> +
> >> +static const struct mvebu_a3700_utmi_caps mvebu_a3700_utmi_host_phy_caps = {
> >> +	.usb32 = false,
> >> +	.ops = &mvebu_a3700_utmi_phy_ops,
> >> +};
> >> +
> >> +static const struct of_device_id mvebu_a3700_utmi_of_match[] = {
> >> +	{
> >> +		.compatible = "marvell,a3700-utmi-otg-phy",
> >> +		.data = &mvebu_a3700_utmi_otg_phy_caps,
> >> +	},
> >> +	{
> >> +		.compatible = "marvell,a3700-utmi-host-phy",
> >> +		.data = &mvebu_a3700_utmi_host_phy_caps,
> >> +	},
> >> +	{},
> >> +};
> >> +MODULE_DEVICE_TABLE(of, mvebu_a3700_utmi_of_match);
> >> +
> >> +static int mvebu_a3700_utmi_phy_probe(struct platform_device *pdev)
> >> +{
> >> +	const struct of_device_id *dev_id;
> >> +	struct device *dev = &pdev->dev;
> >> +	struct mvebu_a3700_utmi *utmi;
> >> +	struct phy_provider *provider;
> >> +	const struct phy_ops *ops;
> >> +	struct resource *res;
> >> +
> >> +	utmi = devm_kzalloc(dev, sizeof(*utmi), GFP_KERNEL);
> >> +	if (!utmi)
> >> +		return -ENOMEM;
> >> +
> >> +	/* Get UTMI memory region */
> >> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> >> +	if (!res) {
> >> +		dev_err(dev, "Missing UTMI PHY memory resource\n");
> >> +		return -ENODEV;
> >> +	}
> >> +
> >> +	utmi->regs = devm_ioremap_resource(dev, res);
> >> +	if (IS_ERR(utmi->regs))
> >> +		return PTR_ERR(utmi->regs);
> >> +
> >> +	/* Get miscellaneous Host/PHY region */
> >> +	utmi->usb_misc = syscon_regmap_lookup_by_phandle(dev->of_node,
> >> +							 "marvell,usb-misc-reg");
> >> +	if (IS_ERR(utmi->usb_misc)) {
> >> +		dev_err(dev,
> >> +			"Missing USB misc purpose system controller\n");
> >> +		return PTR_ERR(utmi->usb_misc);
> >> +	}
> >> +
> >> +	/* Retrieve PHY capabilities */
> >> +	dev_id = of_match_device(mvebu_a3700_utmi_of_match, dev);
> >> +	if (!dev_id)
> >> +		return -EINVAL;
> >> +
> >> +	utmi->caps = dev_id->data;  
> > a useful API to get @data: of_device_get_match_data()

Nice one, I forgot about it.

> >   
> >> +	ops = utmi->caps->ops;
> >> +
> >> +	/* Instantiate the PHY */
> >> +	utmi->phy = devm_phy_create(dev, NULL, ops);
> >> +	if (IS_ERR(utmi->phy)) {
> >> +		dev_err(dev, "Failed to create the UTMI PHY\n");
> >> +		return PTR_ERR(utmi->phy);
> >> +	}
> >> +
> >> +	phy_set_drvdata(utmi->phy, utmi);
> >> +
> >> +	/* Ensure the PHY is powered off */
> >> +	ops->power_off(utmi->phy);
> >> +
> >> +	provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> >> +
> >> +	return PTR_ERR_OR_ZERO(provider);
> >> +}
> >> +
> >> +static int mvebu_a3700_utmi_phy_remove(struct platform_device *pdev)
> >> +{
> >> +	return 0;
> >> +}  
> 
> This empty remove function can be removed.

Sure.

> 
> Thanks
> Kishon
> 
> >> +
> >> +static struct platform_driver mvebu_a3700_utmi_driver = {
> >> +	.probe	= mvebu_a3700_utmi_phy_probe,
> >> +	.remove = mvebu_a3700_utmi_phy_remove,
> >> +	.driver	= {
> >> +		.name		= "mvebu-a3700-utmi-phy",
> >> +		.owner		= THIS_MODULE,
> >> +		.of_match_table	= mvebu_a3700_utmi_of_match,
> >> +	 },
> >> +};
> >> +module_platform_driver(mvebu_a3700_utmi_driver);
> >> +
> >> +MODULE_AUTHOR("Evan Wang <xswang@marvell.com>");
> >> +MODULE_AUTHOR("Miquel Raynal <miquel.raynal@bootlin.com>");
> >> +MODULE_DESCRIPTION("Marvell EBU A3700 UTMI PHY driver");
> >> +MODULE_LICENSE("GPL");  
> > 
> >   

Thanks for reviewing!
Miquèl
diff mbox series

Patch

diff --git a/drivers/phy/marvell/Kconfig b/drivers/phy/marvell/Kconfig
index 9c90c0408ea3..b8e9dd38ad0d 100644
--- a/drivers/phy/marvell/Kconfig
+++ b/drivers/phy/marvell/Kconfig
@@ -33,6 +33,15 @@  config PHY_MVEBU_A3700_COMPHY
 	  shared serdes PHYs on Marvell Armada 3700. Its serdes lanes can be
 	  used by various controllers: Ethernet, SATA, USB3, PCIe.
 
+config PHY_MVEBU_A3700_UTMI
+	tristate "Marvell A3700 UTMI driver"
+	depends on ARCH_MVEBU || COMPILE_TEST
+	depends on OF
+	default y
+	select GENERIC_PHY
+	help
+	  Enable this to support Marvell A3700 UTMI PHY driver.
+
 config PHY_MVEBU_CP110_COMPHY
 	tristate "Marvell CP110 comphy driver"
 	depends on ARCH_MVEBU || COMPILE_TEST
diff --git a/drivers/phy/marvell/Makefile b/drivers/phy/marvell/Makefile
index c13a0c8ab6f0..82f291cf59ee 100644
--- a/drivers/phy/marvell/Makefile
+++ b/drivers/phy/marvell/Makefile
@@ -3,6 +3,7 @@  obj-$(CONFIG_ARMADA375_USBCLUSTER_PHY)	+= phy-armada375-usb2.o
 obj-$(CONFIG_PHY_BERLIN_SATA)		+= phy-berlin-sata.o
 obj-$(CONFIG_PHY_BERLIN_USB)		+= phy-berlin-usb.o
 obj-$(CONFIG_PHY_MVEBU_A3700_COMPHY)	+= phy-mvebu-a3700-comphy.o
+obj-$(CONFIG_PHY_MVEBU_A3700_UTMI)	+= phy-mvebu-a3700-utmi.o
 obj-$(CONFIG_PHY_MVEBU_CP110_COMPHY)	+= phy-mvebu-cp110-comphy.o
 obj-$(CONFIG_PHY_MVEBU_SATA)		+= phy-mvebu-sata.o
 obj-$(CONFIG_PHY_PXA_28NM_HSIC)		+= phy-pxa-28nm-hsic.o
diff --git a/drivers/phy/marvell/phy-mvebu-a3700-utmi.c b/drivers/phy/marvell/phy-mvebu-a3700-utmi.c
new file mode 100644
index 000000000000..97d8235d661d
--- /dev/null
+++ b/drivers/phy/marvell/phy-mvebu-a3700-utmi.c
@@ -0,0 +1,297 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2018 Marvell
+ *
+ * Authors:
+ *   Evan Wang <xswang@marvell.com>
+ *   Miquèl Raynal <miquel.raynal@bootlin.com>
+ *
+ * Marvell A3700 UTMI PHY driver
+ */
+
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+/* Armada 3700 UTMI PHY registers */
+#define USB2_PHY_PLL_CTRL_REG0			0x0
+#define   PLL_REF_DIV_OFF			0
+#define   PLL_REF_DIV_MASK			(0x7F << PLL_REF_DIV_OFF)
+#define   PLL_REF_DIV_5				0x5
+#define   PLL_FB_DIV_OFF			16
+#define   PLL_FB_DIV_MASK			(0x1FF << PLL_FB_DIV_OFF)
+#define   PLL_FB_DIV_96				96
+#define   PLL_SEL_LPFR_OFF			28
+#define   PLL_SEL_LPFR_MASK			(0x3 << PLL_SEL_LPFR_OFF)
+#define   PLL_READY				BIT(31)
+#define USB2_PHY_CAL_CTRL			0x8
+#define   PHY_PLLCAL_DONE			BIT(31)
+#define   PHY_IMPCAL_DONE			BIT(23)
+#define USB2_RX_CHAN_CTRL1			0x18
+#define   USB2PHY_SQCAL_DONE			BIT(31)
+#define USB2_PHY_OTG_CTRL			0x34
+#define   PHY_PU_OTG				BIT(4)
+#define USB2_PHY_CHRGR_DETECT			0x38
+#define   PHY_CDP_EN				BIT(2)
+#define   PHY_DCP_EN				BIT(3)
+#define   PHY_PD_EN				BIT(4)
+#define   PHY_PU_CHRG_DTC			BIT(5)
+#define   PHY_CDP_DM_AUTO			BIT(7)
+#define   PHY_ENSWITCH_DP			BIT(12)
+#define   PHY_ENSWITCH_DM			BIT(13)
+
+/* Armada 3700 USB miscellaneous registers */
+#define USB2_PHY_CTRL(usb32)			(usb32 ? 0x20 : 0x4)
+#define   RB_USB2PHY_PU				BIT(0)
+#define   USB2_DP_PULLDN_DEV_MODE		BIT(5)
+#define   USB2_DM_PULLDN_DEV_MODE		BIT(6)
+#define   RB_USB2PHY_SUSPM(usb32)		(usb32 ? BIT(14) : BIT(7))
+
+#define PLL_LOCK_DELAY_US			10000
+#define PLL_LOCK_TIMEOUT_US			1000000
+
+/**
+ * struct mvebu_a3700_utmi_caps - PHY capabilities
+ *
+ * @usb32: Flag indicating which PHY is in use (impacts the register map):
+ *           - The UTMI PHY wired to the USB3/USB2 controller (otg)
+ *           - The UTMI PHY wired to the USB2 controller (host only)
+ * @ops: PHY operations
+ */
+struct mvebu_a3700_utmi_caps {
+	int usb32;
+	const struct phy_ops *ops;
+};
+
+/**
+ * struct mvebu_a3700_utmi - PHY driver data
+ *
+ * @regs: PHY registers
+ * @usb_mis: Regmap with USB miscellaneous registers including PHY ones
+ * @caps: PHY capabilities
+ * @phy: PHY handle
+ */
+struct mvebu_a3700_utmi {
+	void __iomem *regs;
+	struct regmap *usb_misc;
+	const struct mvebu_a3700_utmi_caps *caps;
+	struct phy *phy;
+};
+
+static int mvebu_a3700_utmi_phy_power_on(struct phy *phy)
+{
+	struct mvebu_a3700_utmi *utmi = phy_get_drvdata(phy);
+	struct device *dev = &phy->dev;
+	int usb32 = utmi->caps->usb32;
+	int ret = 0;
+	u32 reg;
+
+	if (!utmi)
+		return -ENODEV;
+
+	/*
+	 * Setup PLL. 40MHz clock used to be the default, bein 25MHz now.
+	 * See "PLL Settings for Typical REFCLK" table.
+	 */
+	reg = readl(utmi->regs + USB2_PHY_PLL_CTRL_REG0);
+	reg &= ~(PLL_REF_DIV_MASK | PLL_FB_DIV_MASK | PLL_SEL_LPFR_MASK);
+	reg |= (PLL_REF_DIV_5 << PLL_REF_DIV_OFF |
+		PLL_FB_DIV_96 << PLL_FB_DIV_OFF);
+	writel(reg, utmi->regs + USB2_PHY_PLL_CTRL_REG0);
+
+	/* Enable PHY pull up and disable USB2 suspend */
+	regmap_update_bits(utmi->usb_misc, USB2_PHY_CTRL(usb32),
+			   RB_USB2PHY_SUSPM(usb32) | RB_USB2PHY_PU,
+			   RB_USB2PHY_SUSPM(usb32) | RB_USB2PHY_PU);
+
+	if (usb32) {
+		/* Power up OTG module */
+		reg = readl(utmi->regs + USB2_PHY_OTG_CTRL);
+		reg |= PHY_PU_OTG;
+		writel(reg, utmi->regs + USB2_PHY_OTG_CTRL);
+
+		/* Disable PHY charger detection */
+		reg = readl(utmi->regs + USB2_PHY_CHRGR_DETECT);
+		reg &= ~(PHY_CDP_EN | PHY_DCP_EN | PHY_PD_EN | PHY_PU_CHRG_DTC |
+			 PHY_CDP_DM_AUTO | PHY_ENSWITCH_DP | PHY_ENSWITCH_DM);
+		writel(reg, utmi->regs + USB2_PHY_CHRGR_DETECT);
+
+		/* Disable PHY DP/DM pull-down (used for device mode) */
+		regmap_update_bits(utmi->usb_misc, USB2_PHY_CTRL(usb32),
+				   USB2_DP_PULLDN_DEV_MODE |
+				   USB2_DM_PULLDN_DEV_MODE, 0);
+	}
+
+	/* Wait for PLL calibration */
+	ret = readl_poll_timeout(utmi->regs + USB2_PHY_CAL_CTRL, reg,
+				 reg & PHY_PLLCAL_DONE,
+				 PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
+	if (ret) {
+		dev_err(dev, "Failed to end USB2 PLL calibration\n");
+		return ret;
+	}
+
+	/* Wait for impedance calibration */
+	ret = readl_poll_timeout(utmi->regs + USB2_PHY_CAL_CTRL, reg,
+				 reg & PHY_IMPCAL_DONE,
+				 PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
+	if (ret) {
+		dev_err(dev, "Failed to end USB2 impedance calibration\n");
+		return ret;
+	}
+
+	/* Wait for squetch calibration */
+	ret = readl_poll_timeout(utmi->regs + USB2_RX_CHAN_CTRL1, reg,
+				 reg & USB2PHY_SQCAL_DONE,
+				 PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
+	if (ret) {
+		dev_err(dev, "Failed to end USB2 unknown calibration\n");
+		return ret;
+	}
+
+	/* Wait for PLL to be locked */
+	ret = readl_poll_timeout(utmi->regs + USB2_PHY_PLL_CTRL_REG0, reg,
+				 reg & PLL_READY,
+				 PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
+	if (ret)
+		dev_err(dev, "Failed to lock USB2 PLL\n");
+
+	return ret;
+}
+
+static int mvebu_a3700_utmi_phy_power_off(struct phy *phy)
+{
+	struct mvebu_a3700_utmi *utmi = phy_get_drvdata(phy);
+	int usb32 = utmi->caps->usb32;
+	u32 reg;
+
+	if (!utmi)
+		return -ENODEV;
+
+	/* Disable PHY pull-up and enable USB2 suspend */
+	reg = readl(utmi->regs + USB2_PHY_CTRL(usb32));
+	reg &= ~(RB_USB2PHY_PU | RB_USB2PHY_SUSPM(usb32));
+	writel(reg, utmi->regs + USB2_PHY_CTRL(usb32));
+
+	/* Power down OTG module */
+	if (usb32) {
+		reg = readl(utmi->regs + USB2_PHY_OTG_CTRL);
+		reg &= ~PHY_PU_OTG;
+		writel(reg, utmi->regs + USB2_PHY_OTG_CTRL);
+	}
+
+	return 0;
+}
+
+static const struct phy_ops mvebu_a3700_utmi_phy_ops = {
+	.power_on = mvebu_a3700_utmi_phy_power_on,
+	.power_off = mvebu_a3700_utmi_phy_power_off,
+	.owner = THIS_MODULE,
+};
+
+static const struct mvebu_a3700_utmi_caps mvebu_a3700_utmi_otg_phy_caps = {
+	.usb32 = true,
+	.ops = &mvebu_a3700_utmi_phy_ops,
+};
+
+static const struct mvebu_a3700_utmi_caps mvebu_a3700_utmi_host_phy_caps = {
+	.usb32 = false,
+	.ops = &mvebu_a3700_utmi_phy_ops,
+};
+
+static const struct of_device_id mvebu_a3700_utmi_of_match[] = {
+	{
+		.compatible = "marvell,a3700-utmi-otg-phy",
+		.data = &mvebu_a3700_utmi_otg_phy_caps,
+	},
+	{
+		.compatible = "marvell,a3700-utmi-host-phy",
+		.data = &mvebu_a3700_utmi_host_phy_caps,
+	},
+	{},
+};
+MODULE_DEVICE_TABLE(of, mvebu_a3700_utmi_of_match);
+
+static int mvebu_a3700_utmi_phy_probe(struct platform_device *pdev)
+{
+	const struct of_device_id *dev_id;
+	struct device *dev = &pdev->dev;
+	struct mvebu_a3700_utmi *utmi;
+	struct phy_provider *provider;
+	const struct phy_ops *ops;
+	struct resource *res;
+
+	utmi = devm_kzalloc(dev, sizeof(*utmi), GFP_KERNEL);
+	if (!utmi)
+		return -ENOMEM;
+
+	/* Get UTMI memory region */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(dev, "Missing UTMI PHY memory resource\n");
+		return -ENODEV;
+	}
+
+	utmi->regs = devm_ioremap_resource(dev, res);
+	if (IS_ERR(utmi->regs))
+		return PTR_ERR(utmi->regs);
+
+	/* Get miscellaneous Host/PHY region */
+	utmi->usb_misc = syscon_regmap_lookup_by_phandle(dev->of_node,
+							 "marvell,usb-misc-reg");
+	if (IS_ERR(utmi->usb_misc)) {
+		dev_err(dev,
+			"Missing USB misc purpose system controller\n");
+		return PTR_ERR(utmi->usb_misc);
+	}
+
+	/* Retrieve PHY capabilities */
+	dev_id = of_match_device(mvebu_a3700_utmi_of_match, dev);
+	if (!dev_id)
+		return -EINVAL;
+
+	utmi->caps = dev_id->data;
+	ops = utmi->caps->ops;
+
+	/* Instantiate the PHY */
+	utmi->phy = devm_phy_create(dev, NULL, ops);
+	if (IS_ERR(utmi->phy)) {
+		dev_err(dev, "Failed to create the UTMI PHY\n");
+		return PTR_ERR(utmi->phy);
+	}
+
+	phy_set_drvdata(utmi->phy, utmi);
+
+	/* Ensure the PHY is powered off */
+	ops->power_off(utmi->phy);
+
+	provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+	return PTR_ERR_OR_ZERO(provider);
+}
+
+static int mvebu_a3700_utmi_phy_remove(struct platform_device *pdev)
+{
+	return 0;
+}
+
+static struct platform_driver mvebu_a3700_utmi_driver = {
+	.probe	= mvebu_a3700_utmi_phy_probe,
+	.remove = mvebu_a3700_utmi_phy_remove,
+	.driver	= {
+		.name		= "mvebu-a3700-utmi-phy",
+		.owner		= THIS_MODULE,
+		.of_match_table	= mvebu_a3700_utmi_of_match,
+	 },
+};
+module_platform_driver(mvebu_a3700_utmi_driver);
+
+MODULE_AUTHOR("Evan Wang <xswang@marvell.com>");
+MODULE_AUTHOR("Miquel Raynal <miquel.raynal@bootlin.com>");
+MODULE_DESCRIPTION("Marvell EBU A3700 UTMI PHY driver");
+MODULE_LICENSE("GPL");