| Message ID | 1549006693-11659-4-git-send-email-michael.kao@mediatek.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | Add Mediatek thermal dirver for mt8183 | expand |
On 01/02/2019 08:38, michael.kao@mediatek.com wrote: > From: Michael Kao <michael.kao@mediatek.com> > > Add calibration item in thermal_data to support > the project with different calibration coefficient. > > Signed-off-by: Michael Kao <michael.kao@mediatek.com> > --- > drivers/thermal/mtk_thermal.c | 19 ++++++++++++++++++- > 1 file changed, 18 insertions(+), 1 deletion(-) > > diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c > index 07f8ad7..45c6587 100644 > --- a/drivers/thermal/mtk_thermal.c > +++ b/drivers/thermal/mtk_thermal.c > @@ -105,6 +105,9 @@ > /* The number of sensing points per bank */ > #define MT8173_NUM_SENSORS_PER_ZONE 4 > > +/* The calibration coefficient of sensor */ > +#define MT8173_CALIBRATION 165 > + Calibration value is the same for all SoCs (including mt8183), we can define it once and use it in all mtk_thermal structs. Regards, Matthias > /* > * Layout of the fuses providing the calibration data > * These macros could be used for MT8173, MT2701, and MT2712. > @@ -147,6 +150,9 @@ enum { > /* The number of sensing points per bank */ > #define MT2701_NUM_SENSORS_PER_ZONE 3 > > +/* The calibration coefficient of sensor */ > +#define MT2701_CALIBRATION 165 > + > /* MT2712 thermal sensors */ > #define MT2712_TS1 0 > #define MT2712_TS2 1 > @@ -162,12 +168,18 @@ enum { > /* The number of sensing points per bank */ > #define MT2712_NUM_SENSORS_PER_ZONE 4 > > +/* The calibration coefficient of sensor */ > +#define MT2712_CALIBRATION 165 > + > #define MT7622_TEMP_AUXADC_CHANNEL 11 > #define MT7622_NUM_SENSORS 1 > #define MT7622_NUM_ZONES 1 > #define MT7622_NUM_SENSORS_PER_ZONE 1 > #define MT7622_TS1 0 > > +/* The calibration coefficient of sensor */ > +#define MT7622_CALIBRATION 165 > + > struct mtk_thermal; > > struct thermal_bank_cfg { > @@ -188,6 +200,7 @@ struct mtk_thermal_data { > const int *sensor_mux_values; > const int *msr; > const int *adcpnp; > + const int cali_val; > struct thermal_bank_cfg bank_data[]; > }; > > @@ -295,6 +308,7 @@ struct mtk_thermal { > .num_banks = MT8173_NUM_ZONES, > .num_sensors = MT8173_NUM_SENSORS, > .vts_index = mt8173_vts_index, > + .cali_val = MT8173_CALIBRATION, > .bank_data = { > { > .num_sensors = 2, > @@ -330,6 +344,7 @@ struct mtk_thermal { > .num_banks = 1, > .num_sensors = MT2701_NUM_SENSORS, > .vts_index = mt2701_vts_index, > + .cali_val = MT2701_CALIBRATION, > .bank_data = { > { > .num_sensors = 3, > @@ -356,6 +371,7 @@ struct mtk_thermal { > .num_banks = 1, > .num_sensors = MT2712_NUM_SENSORS, > .vts_index = mt2712_vts_index, > + .cali_val = MT2712_CALIBRATION, > .bank_data = { > { > .num_sensors = 4, > @@ -376,6 +392,7 @@ struct mtk_thermal { > .num_banks = MT7622_NUM_ZONES, > .num_sensors = MT7622_NUM_SENSORS, > .vts_index = mt7622_vts_index, > + .cali_val = MT7622_CALIBRATION, > .bank_data = { > { > .num_sensors = 1, > @@ -402,7 +419,7 @@ static int raw_to_mcelsius(struct mtk_thermal *mt, int sensno, s32 raw) > raw &= 0xfff; > > tmp = 203450520 << 3; > - tmp /= 165 + mt->o_slope; > + tmp /= mt->conf->cali_val + mt->o_slope; > tmp /= 10000 + mt->adc_ge; > tmp *= raw - mt->vts[sensno] - 3350; > tmp >>= 3; >
On Mon, Feb 04, 2019 at 06:31:41PM +0100, Matthias Brugger wrote: > > > On 01/02/2019 08:38, michael.kao@mediatek.com wrote: > > From: Michael Kao <michael.kao@mediatek.com> > > > > Add calibration item in thermal_data to support > > the project with different calibration coefficient. > > > > Signed-off-by: Michael Kao <michael.kao@mediatek.com> > > --- > > drivers/thermal/mtk_thermal.c | 19 ++++++++++++++++++- > > 1 file changed, 18 insertions(+), 1 deletion(-) > > > > diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c > > index 07f8ad7..45c6587 100644 > > --- a/drivers/thermal/mtk_thermal.c > > +++ b/drivers/thermal/mtk_thermal.c > > @@ -105,6 +105,9 @@ > > /* The number of sensing points per bank */ > > #define MT8173_NUM_SENSORS_PER_ZONE 4 > > > > +/* The calibration coefficient of sensor */ > > +#define MT8173_CALIBRATION 165 > > + > > Calibration value is the same for all SoCs (including mt8183), we can define it > once and use it in all mtk_thermal structs. Well, on patch 7 we have: +#define MT8183_CALIBRATION 153 > > Regards, > Matthias > > > > /* > > * Layout of the fuses providing the calibration data > > * These macros could be used for MT8173, MT2701, and MT2712. > > @@ -147,6 +150,9 @@ enum { > > /* The number of sensing points per bank */ > > #define MT2701_NUM_SENSORS_PER_ZONE 3 > > > > +/* The calibration coefficient of sensor */ > > +#define MT2701_CALIBRATION 165 > > + > > /* MT2712 thermal sensors */ > > #define MT2712_TS1 0 > > #define MT2712_TS2 1 > > @@ -162,12 +168,18 @@ enum { > > /* The number of sensing points per bank */ > > #define MT2712_NUM_SENSORS_PER_ZONE 4 > > > > +/* The calibration coefficient of sensor */ > > +#define MT2712_CALIBRATION 165 > > + > > #define MT7622_TEMP_AUXADC_CHANNEL 11 > > #define MT7622_NUM_SENSORS 1 > > #define MT7622_NUM_ZONES 1 > > #define MT7622_NUM_SENSORS_PER_ZONE 1 > > #define MT7622_TS1 0 > > > > +/* The calibration coefficient of sensor */ > > +#define MT7622_CALIBRATION 165 > > + > > struct mtk_thermal; > > > > struct thermal_bank_cfg { > > @@ -188,6 +200,7 @@ struct mtk_thermal_data { > > const int *sensor_mux_values; > > const int *msr; > > const int *adcpnp; > > + const int cali_val; > > struct thermal_bank_cfg bank_data[]; > > }; > > > > @@ -295,6 +308,7 @@ struct mtk_thermal { > > .num_banks = MT8173_NUM_ZONES, > > .num_sensors = MT8173_NUM_SENSORS, > > .vts_index = mt8173_vts_index, > > + .cali_val = MT8173_CALIBRATION, > > .bank_data = { > > { > > .num_sensors = 2, > > @@ -330,6 +344,7 @@ struct mtk_thermal { > > .num_banks = 1, > > .num_sensors = MT2701_NUM_SENSORS, > > .vts_index = mt2701_vts_index, > > + .cali_val = MT2701_CALIBRATION, > > .bank_data = { > > { > > .num_sensors = 3, > > @@ -356,6 +371,7 @@ struct mtk_thermal { > > .num_banks = 1, > > .num_sensors = MT2712_NUM_SENSORS, > > .vts_index = mt2712_vts_index, > > + .cali_val = MT2712_CALIBRATION, > > .bank_data = { > > { > > .num_sensors = 4, > > @@ -376,6 +392,7 @@ struct mtk_thermal { > > .num_banks = MT7622_NUM_ZONES, > > .num_sensors = MT7622_NUM_SENSORS, > > .vts_index = mt7622_vts_index, > > + .cali_val = MT7622_CALIBRATION, > > .bank_data = { > > { > > .num_sensors = 1, > > @@ -402,7 +419,7 @@ static int raw_to_mcelsius(struct mtk_thermal *mt, int sensno, s32 raw) > > raw &= 0xfff; > > > > tmp = 203450520 << 3; > > - tmp /= 165 + mt->o_slope; > > + tmp /= mt->conf->cali_val + mt->o_slope; > > tmp /= 10000 + mt->adc_ge; > > tmp *= raw - mt->vts[sensno] - 3350; > > tmp >>= 3; > >
diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c index 07f8ad7..45c6587 100644 --- a/drivers/thermal/mtk_thermal.c +++ b/drivers/thermal/mtk_thermal.c @@ -105,6 +105,9 @@ /* The number of sensing points per bank */ #define MT8173_NUM_SENSORS_PER_ZONE 4 +/* The calibration coefficient of sensor */ +#define MT8173_CALIBRATION 165 + /* * Layout of the fuses providing the calibration data * These macros could be used for MT8173, MT2701, and MT2712. @@ -147,6 +150,9 @@ enum { /* The number of sensing points per bank */ #define MT2701_NUM_SENSORS_PER_ZONE 3 +/* The calibration coefficient of sensor */ +#define MT2701_CALIBRATION 165 + /* MT2712 thermal sensors */ #define MT2712_TS1 0 #define MT2712_TS2 1 @@ -162,12 +168,18 @@ enum { /* The number of sensing points per bank */ #define MT2712_NUM_SENSORS_PER_ZONE 4 +/* The calibration coefficient of sensor */ +#define MT2712_CALIBRATION 165 + #define MT7622_TEMP_AUXADC_CHANNEL 11 #define MT7622_NUM_SENSORS 1 #define MT7622_NUM_ZONES 1 #define MT7622_NUM_SENSORS_PER_ZONE 1 #define MT7622_TS1 0 +/* The calibration coefficient of sensor */ +#define MT7622_CALIBRATION 165 + struct mtk_thermal; struct thermal_bank_cfg { @@ -188,6 +200,7 @@ struct mtk_thermal_data { const int *sensor_mux_values; const int *msr; const int *adcpnp; + const int cali_val; struct thermal_bank_cfg bank_data[]; }; @@ -295,6 +308,7 @@ struct mtk_thermal { .num_banks = MT8173_NUM_ZONES, .num_sensors = MT8173_NUM_SENSORS, .vts_index = mt8173_vts_index, + .cali_val = MT8173_CALIBRATION, .bank_data = { { .num_sensors = 2, @@ -330,6 +344,7 @@ struct mtk_thermal { .num_banks = 1, .num_sensors = MT2701_NUM_SENSORS, .vts_index = mt2701_vts_index, + .cali_val = MT2701_CALIBRATION, .bank_data = { { .num_sensors = 3, @@ -356,6 +371,7 @@ struct mtk_thermal { .num_banks = 1, .num_sensors = MT2712_NUM_SENSORS, .vts_index = mt2712_vts_index, + .cali_val = MT2712_CALIBRATION, .bank_data = { { .num_sensors = 4, @@ -376,6 +392,7 @@ struct mtk_thermal { .num_banks = MT7622_NUM_ZONES, .num_sensors = MT7622_NUM_SENSORS, .vts_index = mt7622_vts_index, + .cali_val = MT7622_CALIBRATION, .bank_data = { { .num_sensors = 1, @@ -402,7 +419,7 @@ static int raw_to_mcelsius(struct mtk_thermal *mt, int sensno, s32 raw) raw &= 0xfff; tmp = 203450520 << 3; - tmp /= 165 + mt->o_slope; + tmp /= mt->conf->cali_val + mt->o_slope; tmp /= 10000 + mt->adc_ge; tmp *= raw - mt->vts[sensno] - 3350; tmp >>= 3;