Message ID | 20190217121513.22965-4-beagleboard@davidjohnsummers.uk (mailing list archive) |
---|---|
State | New, archived |
Headers | show |
Series | ARM: dts: rk3288 Tinker Board (S) updates | expand |
Hello Dave, For the Bluetooth I can confirm _RTS is required, quite a lot of work went into creating a userspace solution for the Tinker Board bluetooth for Armbian by myself and by Miouyouyou for a more generic mainline patchset. Without RTS the rtk_hciattach handshake fails. On Sun, Feb 17, 2019 at 7:17 AM David Summers <beagleboard@davidjohnsummers.uk> wrote: > > This patch is to add Bluetooth to the ASUS Tinker Board (S) device > tree. > > This patch is more contraversal - so probably view it as a request for > comments. > > The reason behind this, is this patch does not currently set Bluetooth > working on the these boards. The problem is that the > bluetooth/hci_h5.c driver, that is used for Realtek serial devices, > depends on ACPI. Unfortantly ACPI can not be enabled on armv7 machines > such as the TB(S). And so the kernel module for the RTL8723BS > Bluetooth can not be loaded. > > However this patch is believed to be an accurate description of the > Tinker Board (S) wiring. It is strongly based on the ASUS patch: > > https://github.com/TinkerBoard/debian_kernel/commit/6a3128ade33f758887048578ada61a4b7ab8e678 > > As the Bluetooth is connected via a UART and this is wired into uart0, > this has been described as a SerDev. > > The ASUS patch mentions the UART_CTS, but not the _RTS. Now as the > RTL8723BS has both CTS and RTS on the uart, it has been assumed both > are wired into uart0 on the cpu. > > The Bluetooth connection has several wake up pins both device and host > and a reset pin. The wiring of these has been described; however how > the kernel driver will use these isn't clear. E.g. should HOST_WAKE be > an interupt? > > The main reason for asking for comments, is that when it comes time to > make the changes to the bluetooth uart code, and add compatible flags, > robh has indicated that this will only be accepted with a valid > example. So the code below is that example. So I would like comments > that this approach is valid, which can be used when the later > submission comes. > > Signed-off-by: David Summers <beagleboard@davidjohnsummers.uk> > --- > arch/arm/boot/dts/rk3288-tinker.dtsi | 11 +++++++++++ > 1 file changed, 11 insertions(+) > > diff --git a/arch/arm/boot/dts/rk3288-tinker.dtsi b/arch/arm/boot/dts/rk3288-tinker.dtsi > index e1796f340eef..931b4c652fdc 100644 > --- a/arch/arm/boot/dts/rk3288-tinker.dtsi > +++ b/arch/arm/boot/dts/rk3288-tinker.dtsi > @@ -481,6 +481,17 @@ > > &uart0 { > status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&uart0_xfer>, <&uart0_cts>, <&uart0_rts>; > + > + bluetooth { > + clocks = <&rk808 RK808_CLKOUT1>; > + reset-gpios = <&gpio4 RK_PD5 GPIO_ACTIVE_LOW>; > + device-wake-gpios = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>; > + host-wake-gpios = <&gpio4 RK_PD7 GPIO_ACTIVE_HIGH>; > + vcc-18-supply = <&vcc_18>; > + vcc-io-supply = <&vcc_io>; > + }; > }; > > &uart1 { > -- > beagleboard@davidjohnsummers.uk > > > _______________________________________________ > Linux-rockchip mailing list > Linux-rockchip@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-rockchip
Hi David, > David Summers <beagleboard@davidjohnsummers.uk> hat am 17. Februar 2019 um 13:15 geschrieben: > > > This patch is to add Bluetooth to the ASUS Tinker Board (S) device > tree. > > This patch is more contraversal - so probably view it as a request for > comments. > > The reason behind this, is this patch does not currently set Bluetooth > working on the these boards. The problem is that the > bluetooth/hci_h5.c driver, that is used for Realtek serial devices, > depends on ACPI. Unfortantly ACPI can not be enabled on armv7 machines > such as the TB(S). And so the kernel module for the RTL8723BS > Bluetooth can not be loaded. > > However this patch is believed to be an accurate description of the > Tinker Board (S) wiring. It is strongly based on the ASUS patch: > > https://github.com/TinkerBoard/debian_kernel/commit/6a3128ade33f758887048578ada61a4b7ab8e678 > > As the Bluetooth is connected via a UART and this is wired into uart0, > this has been described as a SerDev. > > The ASUS patch mentions the UART_CTS, but not the _RTS. Now as the > RTL8723BS has both CTS and RTS on the uart, it has been assumed both > are wired into uart0 on the cpu. which would be very strange, because we could use H4 instead of H5. > > The Bluetooth connection has several wake up pins both device and host > and a reset pin. The wiring of these has been described; however how > the kernel driver will use these isn't clear. E.g. should HOST_WAKE be > an interupt? > > The main reason for asking for comments, is that when it comes time to > make the changes to the bluetooth uart code, and add compatible flags, > robh has indicated that this will only be accepted with a valid > example. So the code below is that example. So I would like comments > that this approach is valid, which can be used when the later > submission comes. Asking for comment should be mark with RFC in the patch subject. > > Signed-off-by: David Summers <beagleboard@davidjohnsummers.uk> > --- > arch/arm/boot/dts/rk3288-tinker.dtsi | 11 +++++++++++ > 1 file changed, 11 insertions(+) > > diff --git a/arch/arm/boot/dts/rk3288-tinker.dtsi b/arch/arm/boot/dts/rk3288-tinker.dtsi > index e1796f340eef..931b4c652fdc 100644 > --- a/arch/arm/boot/dts/rk3288-tinker.dtsi > +++ b/arch/arm/boot/dts/rk3288-tinker.dtsi > @@ -481,6 +481,17 @@ > > &uart0 { > status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&uart0_xfer>, <&uart0_cts>, <&uart0_rts>; > + > + bluetooth { > + clocks = <&rk808 RK808_CLKOUT1>; As we already linked the RK808 clock in the sdio pwrseq, we shouldn't do this here again. > + reset-gpios = <&gpio4 RK_PD5 GPIO_ACTIVE_LOW>; reset-gpios isn't compatible to hci_h5, please use my preliminary dt-binding > + device-wake-gpios = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>; > + host-wake-gpios = <&gpio4 RK_PD7 GPIO_ACTIVE_HIGH>; AFAIK hci_h5 doesn't support host-wake yet. So if you want to keep for the future we should make a comment. > + vcc-18-supply = <&vcc_18>; > + vcc-io-supply = <&vcc_io>; Please drop these as the driver doesn't use it and it's already linked in the sdio pwrseq. Thanks Stefan > + }; [1] - https://gist.github.com/lategoodbye/79bac99d4f1158a719a48ea3c45eb7f1#file-0002-dt-bindings-add-support-for-realtek-bluetooth-serial-patch
On 17/02/2019 21:05, Stefan Wahren wrote: > Hi David, > >> David Summers <beagleboard@davidjohnsummers.uk> hat am 17. Februar 2019 um 13:15 geschrieben: >> >> >> This patch is to add Bluetooth to the ASUS Tinker Board (S) device >> tree. >> >> This patch is more contraversal - so probably view it as a request for >> comments. >> >> The reason behind this, is this patch does not currently set Bluetooth >> working on the these boards. The problem is that the >> bluetooth/hci_h5.c driver, that is used for Realtek serial devices, >> depends on ACPI. Unfortantly ACPI can not be enabled on armv7 machines >> such as the TB(S). And so the kernel module for the RTL8723BS >> Bluetooth can not be loaded. >> >> However this patch is believed to be an accurate description of the >> Tinker Board (S) wiring. It is strongly based on the ASUS patch: >> >> https://github.com/TinkerBoard/debian_kernel/commit/6a3128ade33f758887048578ada61a4b7ab8e678 >> >> As the Bluetooth is connected via a UART and this is wired into uart0, >> this has been described as a SerDev. >> >> The ASUS patch mentions the UART_CTS, but not the _RTS. Now as the >> RTL8723BS has both CTS and RTS on the uart, it has been assumed both >> are wired into uart0 on the cpu. > which would be very strange, because we could use H4 instead of H5. Well the bluetooth maintainer said it was hci_h5. The device is BT4.0 and that under Volume 4 HCI, Part D - 2 wire UART Transport Layer, in section 11.2 says that Hardware flow control may be used. Also if you check what ASUS did: https://github.com/TinkerBoard/debian_kernel/commit/5106d9486cf1c2bad4f701611f51a526191c56ad They added H5 code to the hci_h4.c, seems strange but thats what they said they did. Now maybe the RTL8723BS could work with the UART Transport Layer, but that hasn't been done yet. 3 wire has some overhead, but it doesn't look like much. To my mind though it down to the bluetooth Maintainer - so CCing Marcel Holtmann in ... >> The Bluetooth connection has several wake up pins both device and host >> and a reset pin. The wiring of these has been described; however how >> the kernel driver will use these isn't clear. E.g. should HOST_WAKE be >> an interupt? >> >> The main reason for asking for comments, is that when it comes time to >> make the changes to the bluetooth uart code, and add compatible flags, >> robh has indicated that this will only be accepted with a valid >> example. So the code below is that example. So I would like comments >> that this approach is valid, which can be used when the later >> submission comes. > Asking for comment should be mark with RFC in the patch subject. OOps my mistake. >> Signed-off-by: David Summers <beagleboard@davidjohnsummers.uk> >> --- >> arch/arm/boot/dts/rk3288-tinker.dtsi | 11 +++++++++++ >> 1 file changed, 11 insertions(+) >> >> diff --git a/arch/arm/boot/dts/rk3288-tinker.dtsi b/arch/arm/boot/dts/rk3288-tinker.dtsi >> index e1796f340eef..931b4c652fdc 100644 >> --- a/arch/arm/boot/dts/rk3288-tinker.dtsi >> +++ b/arch/arm/boot/dts/rk3288-tinker.dtsi >> @@ -481,6 +481,17 @@ >> >> &uart0 { >> status = "okay"; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&uart0_xfer>, <&uart0_cts>, <&uart0_rts>; >> + >> + bluetooth { >> + clocks = <&rk808 RK808_CLKOUT1>; > As we already linked the RK808 clock in the sdio pwrseq, we shouldn't do this here again. > >> + reset-gpios = <&gpio4 RK_PD5 GPIO_ACTIVE_LOW>; > reset-gpios isn't compatible to hci_h5, please use my preliminary dt-binding > >> + device-wake-gpios = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>; >> + host-wake-gpios = <&gpio4 RK_PD7 GPIO_ACTIVE_HIGH>; > AFAIK hci_h5 doesn't support host-wake yet. So if you want to keep for the future we should make a comment. > >> + vcc-18-supply = <&vcc_18>; >> + vcc-io-supply = <&vcc_io>; > Please drop these as the driver doesn't use it and it's already linked in the sdio pwrseq. > > Thanks Stefan > >> + }; > [1] - https://gist.github.com/lategoodbye/79bac99d4f1158a719a48ea3c45eb7f1#file-0002-dt-bindings-add-support-for-realtek-bluetooth-serial-patch Sorry I disagree here. Last time I posted an example patch like this robh said clearly that these should give clocks, power, etc: https://www.spinics.net/lists/linux-bluetooth/msg78545.html https://www.spinics.net/lists/linux-bluetooth/msg78585.html <https://www.spinics.net/lists/linux-bluetooth/msg78585.html> and as he is maintainer he wins. I can understand Robs position, device tree are for describing hardware, they aren't primarily for helping code to load. Yes that is a second effect, its so it knows what is in the hardware. In this case what if someone wanted Bluetooth, but not WiFi - then the Bluetooth should know what power and clocks are needed. Now that the driver doesn't understand these things is secondary. Maybe that will be cured in future?
Hi David, > David Summers <beagleboard@davidjohnsummers.uk> hat am 18. Februar 2019 um 21:47 geschrieben: > > > On 17/02/2019 21:05, Stefan Wahren wrote: > > Hi David, > > > >> David Summers <beagleboard@davidjohnsummers.uk> hat am 17. Februar 2019 um 13:15 geschrieben: > >> > >> +++ b/arch/arm/boot/dts/rk3288-tinker.dtsi > >> @@ -481,6 +481,17 @@ > >> > >> &uart0 { > >> status = "okay"; > >> + pinctrl-names = "default"; > >> + pinctrl-0 = <&uart0_xfer>, <&uart0_cts>, <&uart0_rts>; > >> + > >> + bluetooth { > >> + clocks = <&rk808 RK808_CLKOUT1>; > > As we already linked the RK808 clock in the sdio pwrseq, we shouldn't do this here again. > > > >> + reset-gpios = <&gpio4 RK_PD5 GPIO_ACTIVE_LOW>; > > reset-gpios isn't compatible to hci_h5, please use my preliminary dt-binding > > > >> + device-wake-gpios = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>; > >> + host-wake-gpios = <&gpio4 RK_PD7 GPIO_ACTIVE_HIGH>; > > AFAIK hci_h5 doesn't support host-wake yet. So if you want to keep for the future we should make a comment. > > > >> + vcc-18-supply = <&vcc_18>; > >> + vcc-io-supply = <&vcc_io>; > > Please drop these as the driver doesn't use it and it's already linked in the sdio pwrseq. > > > > Thanks Stefan > > > >> + }; > > [1] - https://gist.github.com/lategoodbye/79bac99d4f1158a719a48ea3c45eb7f1#file-0002-dt-bindings-add-support-for-realtek-bluetooth-serial-patch > > Sorry I disagree here. > > Last time I posted an example patch like this robh said clearly that > these should give clocks, power, etc: > > https://www.spinics.net/lists/linux-bluetooth/msg78545.html > https://www.spinics.net/lists/linux-bluetooth/msg78585.html > <https://www.spinics.net/lists/linux-bluetooth/msg78585.html> > > and as he is maintainer he wins. > > I can understand Robs position, device tree are for describing hardware, > they aren't primarily for helping code to load. Yes that is a second > effect, its so it knows what is in the hardware. In this case what if > someone wanted Bluetooth, but not WiFi - then the Bluetooth should know > what power and clocks are needed. Now that the driver doesn't understand > these things is secondary. Maybe that will be cured in future? > you need to consider to context of the discussion. The link pointed to a discussion about the dt-binding. A binding should describe all parts (even optional) of the hardware and that is the reason why i explained in Arch board that we need 3 parts for bluetooth (dt-binding, driver change and finally the dts change). Since you avoid that and send only the last part without compatibles causes confusion. We usually don't change DTS properties because it's considered as an ABI, which means we should do it properly in the first run. So lets make the step one (test bluetooth) and not step four ... Regards Stefan
Finally on the patch to give an outline description to Bluetooth on the Tinker Boards. Synthesis here is harder. On the one hand, it is non functioning - because although it describes the hardware, it has no compatible flag, and there is no current driver in the kernel. It should be said though there is a patch for a proposed driver: https://www.spinics.net/lists/linux-bluetooth/msg78661.html And if accepted this would give the compatible flag. So should this change wait until that is added? An alternative approach though arises from what Tony McKahan of Armbian writes "For the Bluetooth I can confirm _RTS is required" So this device tree segment is useful - it correctly describes the uart portion of the interface, and that is hard to determine from the ASUS dts. So this is useful information to capture. On the pinout information of the rtl8723. Two points: 1) information like clock, and voltage supplies, are formally hardware correct, but practically will probably never be applied via bluetooth. Instead its the wifi that brings this hardware up. So should these be supplied if unlikly to be used? I think they should as they formally describe the hardware. 2) Confusion over enable-gpios vs reset-gpios The second appeared on the bluetooth thread: https://www.spinics.net/lists/linux-bluetooth/msg78654.html should this be written: enable-gpios = <&gpio4 RK_PD5 GPIO_ACTIVE_LOW>; or reset-gpios = <&gpio4 RK_PD5 GPIO_ACTIVE_HIGH>; The datasheet (as available as it is): http://cit.odessa.ua/media/pdf/Intel-Compute-Stick/FN-Link_F23BDSM25-W1.pdf Says it is BT_RST - BT Reset IN but the current kernel driver hci_h5 says: https://github.com/torvalds/linux/blob/master/drivers/bluetooth/hci_h5.c#L989 { "enable-gpios", &btrtl_enable_gpios, 1 }, And RobH clearly has a view: https://www.spinics.net/lists/linux-bluetooth/msg79138.html So there is still some confusion. Guess its a question of it a partial hardware description, with possible faults, is better than no device tree description of the hardware? Any views? On 17/02/2019 12:15, David Summers wrote: > This patch is to add Bluetooth to the ASUS Tinker Board (S) device > tree. > > This patch is more contraversal - so probably view it as a request for > comments. > > The reason behind this, is this patch does not currently set Bluetooth > working on the these boards. The problem is that the > bluetooth/hci_h5.c driver, that is used for Realtek serial devices, > depends on ACPI. Unfortantly ACPI can not be enabled on armv7 machines > such as the TB(S). And so the kernel module for the RTL8723BS > Bluetooth can not be loaded. > > However this patch is believed to be an accurate description of the > Tinker Board (S) wiring. It is strongly based on the ASUS patch: > > https://github.com/TinkerBoard/debian_kernel/commit/6a3128ade33f758887048578ada61a4b7ab8e678 > > As the Bluetooth is connected via a UART and this is wired into uart0, > this has been described as a SerDev. > > The ASUS patch mentions the UART_CTS, but not the _RTS. Now as the > RTL8723BS has both CTS and RTS on the uart, it has been assumed both > are wired into uart0 on the cpu. > > The Bluetooth connection has several wake up pins both device and host > and a reset pin. The wiring of these has been described; however how > the kernel driver will use these isn't clear. E.g. should HOST_WAKE be > an interupt? > > The main reason for asking for comments, is that when it comes time to > make the changes to the bluetooth uart code, and add compatible flags, > robh has indicated that this will only be accepted with a valid > example. So the code below is that example. So I would like comments > that this approach is valid, which can be used when the later > submission comes. > > Signed-off-by: David Summers <beagleboard@davidjohnsummers.uk> > --- > arch/arm/boot/dts/rk3288-tinker.dtsi | 11 +++++++++++ > 1 file changed, 11 insertions(+) > > diff --git a/arch/arm/boot/dts/rk3288-tinker.dtsi b/arch/arm/boot/dts/rk3288-tinker.dtsi > index e1796f340eef..931b4c652fdc 100644 > --- a/arch/arm/boot/dts/rk3288-tinker.dtsi > +++ b/arch/arm/boot/dts/rk3288-tinker.dtsi > @@ -481,6 +481,17 @@ > > &uart0 { > status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&uart0_xfer>, <&uart0_cts>, <&uart0_rts>; > + > + bluetooth { > + clocks = <&rk808 RK808_CLKOUT1>; > + reset-gpios = <&gpio4 RK_PD5 GPIO_ACTIVE_LOW>; > + device-wake-gpios = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>; > + host-wake-gpios = <&gpio4 RK_PD7 GPIO_ACTIVE_HIGH>; > + vcc-18-supply = <&vcc_18>; > + vcc-io-supply = <&vcc_io>; > + }; > }; > > &uart1 {
diff --git a/arch/arm/boot/dts/rk3288-tinker.dtsi b/arch/arm/boot/dts/rk3288-tinker.dtsi index e1796f340eef..931b4c652fdc 100644 --- a/arch/arm/boot/dts/rk3288-tinker.dtsi +++ b/arch/arm/boot/dts/rk3288-tinker.dtsi @@ -481,6 +481,17 @@ &uart0 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&uart0_xfer>, <&uart0_cts>, <&uart0_rts>; + + bluetooth { + clocks = <&rk808 RK808_CLKOUT1>; + reset-gpios = <&gpio4 RK_PD5 GPIO_ACTIVE_LOW>; + device-wake-gpios = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>; + host-wake-gpios = <&gpio4 RK_PD7 GPIO_ACTIVE_HIGH>; + vcc-18-supply = <&vcc_18>; + vcc-io-supply = <&vcc_io>; + }; }; &uart1 {
This patch is to add Bluetooth to the ASUS Tinker Board (S) device tree. This patch is more contraversal - so probably view it as a request for comments. The reason behind this, is this patch does not currently set Bluetooth working on the these boards. The problem is that the bluetooth/hci_h5.c driver, that is used for Realtek serial devices, depends on ACPI. Unfortantly ACPI can not be enabled on armv7 machines such as the TB(S). And so the kernel module for the RTL8723BS Bluetooth can not be loaded. However this patch is believed to be an accurate description of the Tinker Board (S) wiring. It is strongly based on the ASUS patch: https://github.com/TinkerBoard/debian_kernel/commit/6a3128ade33f758887048578ada61a4b7ab8e678 As the Bluetooth is connected via a UART and this is wired into uart0, this has been described as a SerDev. The ASUS patch mentions the UART_CTS, but not the _RTS. Now as the RTL8723BS has both CTS and RTS on the uart, it has been assumed both are wired into uart0 on the cpu. The Bluetooth connection has several wake up pins both device and host and a reset pin. The wiring of these has been described; however how the kernel driver will use these isn't clear. E.g. should HOST_WAKE be an interupt? The main reason for asking for comments, is that when it comes time to make the changes to the bluetooth uart code, and add compatible flags, robh has indicated that this will only be accepted with a valid example. So the code below is that example. So I would like comments that this approach is valid, which can be used when the later submission comes. Signed-off-by: David Summers <beagleboard@davidjohnsummers.uk> --- arch/arm/boot/dts/rk3288-tinker.dtsi | 11 +++++++++++ 1 file changed, 11 insertions(+)