| Message ID | 1551781151-5562-3-git-send-email-l.luba@partner.samsung.com (mailing list archive) |
|---|---|
| State | Not Applicable |
| Headers | show |
| Series | [v5,1/8] clk: samsung: add needed IDs for DMC clocks in Exynos5420 | expand |
Hi Lukasz, You are missing some answer on v4 patch[1] and then send the patch without modification. On many times, I mentioned that please answer from the comment. Please check the comments from reviewers carefully without any lost. - [v4,2/8] clk: samsung: add new clocks for DMC for Exynos5422 SoC [1] https://lkml.org/lkml/2019/2/12/12 Please answer from the following comment. [Following comments on v4 patch] >>> + DIV(0, "dout_pclk_drex0", "dout_cclk_drex0", DIV_CDREX0, 28, 3), >> >> Before applied this patch, on line 809, DIV_CDREX0[28:30] was already >> defined with "dout_pclk_cdrex" gate clock name. > In my previous email, I have mentioned that the same bits > (8 combinations) are controlling 3 dividers, which re-branch to 3 edges > in the clock tree named: > CLKDIV_PCLK_CDREX, CLKDIV_PCLK_DREX0, CLKDIV_PCLK_DREX1. > It is in the Exynos5422_UM_REV0.10 documentation section: > 7.9.6.7 CLK_DIV_CDREX0 It is my missing point. I checked it on Exynos5422 TRM. I want to develop the clocks according to H/W clock. Please keep it without removal. Instead, It is very strange case. So, you need to add the detailed comment when defining the multiple clocks with same register/same bits. Also, in order to reduce the confusion of this strange case, IMO you better to define the three clocks at the nearby in this driver. (CLKDIV_PCLK_CDREX, CLKDIV_PCLK_DREX0, CLKDIV_PCLK_DREX1) If they are scattered, it is difficult for understanding why they are developed like this. On 19. 3. 5. 오후 7:19, Lukasz Luba wrote: > This patch provides support for clocks needed for Dynamic Memory Controller > in Exynos5422 SoC. It adds CDREX base register addresses, new DIV, MUX and > GATE entries. > > Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com> > --- > drivers/clk/samsung/clk-exynos5420.c | 54 +++++++++++++++++++++++++++++++++--- > 1 file changed, 50 insertions(+), 4 deletions(-) > > diff --git a/drivers/clk/samsung/clk-exynos5420.c b/drivers/clk/samsung/clk-exynos5420.c > index 34cce3c..6da5875 100644 > --- a/drivers/clk/samsung/clk-exynos5420.c > +++ b/drivers/clk/samsung/clk-exynos5420.c > @@ -134,6 +134,10 @@ > #define SRC_CDREX 0x20200 > #define DIV_CDREX0 0x20500 > #define DIV_CDREX1 0x20504 > +#define GATE_BUS_CDREX0 0x20700 > +#define GATE_BUS_CDREX1 0x20704 > +#define CDREX_PAUSE 0x2091c > +#define CDREX_LPDDR3PHY_CON3 0x20a20 > #define KPLL_LOCK 0x28000 > #define KPLL_CON0 0x28100 > #define SRC_KFC 0x28200 > @@ -248,6 +252,10 @@ static const unsigned long exynos5x_clk_regs[] __initconst = { > DIV_CDREX1, > SRC_KFC, > DIV_KFC0, > + GATE_BUS_CDREX0, > + GATE_BUS_CDREX1, > + CDREX_PAUSE, > + CDREX_LPDDR3PHY_CON3, > }; > > static const unsigned long exynos5800_clk_regs[] __initconst = { > @@ -425,6 +433,9 @@ PNAME(mout_group13_5800_p) = { "dout_osc_div", "mout_sw_aclkfl1_550_cam" }; > PNAME(mout_group14_5800_p) = { "dout_aclk550_cam", "dout_sclk_sw" }; > PNAME(mout_group15_5800_p) = { "dout_osc_div", "mout_sw_aclk550_cam" }; > PNAME(mout_group16_5800_p) = { "dout_osc_div", "mout_mau_epll_clk" }; > +PNAME(mout_mx_mspll_ccore_phy_p) = { "sclk_bpll", "mout_sclk_dpll", > + "mout_sclk_mpll", "ff_dout_spll2", > + "mout_sclk_spll", "mout_sclk_epll"}; > > /* fixed rate clocks generated outside the soc */ > static struct samsung_fixed_rate_clock > @@ -450,7 +461,7 @@ static const struct samsung_fixed_factor_clock > static const struct samsung_fixed_factor_clock > exynos5800_fixed_factor_clks[] __initconst = { > FFACTOR(0, "ff_dout_epll2", "mout_sclk_epll", 1, 2, 0), > - FFACTOR(0, "ff_dout_spll2", "mout_sclk_spll", 1, 2, 0), > + FFACTOR(CLK_FF_DOUT_SPLL2, "ff_dout_spll2", "mout_sclk_spll", 1, 2, 0), > }; > > static const struct samsung_mux_clock exynos5800_mux_clks[] __initconst = { > @@ -472,11 +483,14 @@ static const struct samsung_mux_clock exynos5800_mux_clks[] __initconst = { > MUX(0, "mout_aclk300_disp1", mout_group5_5800_p, SRC_TOP2, 24, 2), > MUX(0, "mout_aclk300_gscl", mout_group5_5800_p, SRC_TOP2, 28, 2), > > + MUX(CLK_MOUT_MX_MSPLL_CCORE_PHY, "mout_mx_mspll_ccore_phy", > + mout_mx_mspll_ccore_phy_p, SRC_TOP7, 0, 3), > + > MUX(CLK_MOUT_MX_MSPLL_CCORE, "mout_mx_mspll_ccore", > - mout_mx_mspll_ccore_p, SRC_TOP7, 16, 2), > + mout_mx_mspll_ccore_p, SRC_TOP7, 16, 3), > MUX_F(CLK_MOUT_MAU_EPLL, "mout_mau_epll_clk", mout_mau_epll_clk_5800_p, > SRC_TOP7, 20, 2, CLK_SET_RATE_PARENT, 0), > - MUX(0, "sclk_bpll", mout_bpll_p, SRC_TOP7, 24, 1), > + MUX(CLK_SCLK_BPLL, "sclk_bpll", mout_bpll_p, SRC_TOP7, 24, 1), > MUX(0, "mout_epll2", mout_epll2_5800_p, SRC_TOP7, 28, 1), > > MUX(0, "mout_aclk550_cam", mout_group3_5800_p, SRC_TOP8, 16, 3), > @@ -648,7 +662,7 @@ static const struct samsung_mux_clock exynos5x_mux_clks[] __initconst = { > > MUX(0, "mout_sclk_mpll", mout_mpll_p, SRC_TOP6, 0, 1), > MUX(CLK_MOUT_VPLL, "mout_sclk_vpll", mout_vpll_p, SRC_TOP6, 4, 1), > - MUX(0, "mout_sclk_spll", mout_spll_p, SRC_TOP6, 8, 1), > + MUX(CLK_MOUT_SCLK_SPLL, "mout_sclk_spll", mout_spll_p, SRC_TOP6, 8, 1), > MUX(0, "mout_sclk_ipll", mout_ipll_p, SRC_TOP6, 12, 1), > MUX(0, "mout_sclk_rpll", mout_rpll_p, SRC_TOP6, 16, 1), > MUX_F(CLK_MOUT_EPLL, "mout_sclk_epll", mout_epll_p, SRC_TOP6, 20, 1, > @@ -817,6 +831,8 @@ static const struct samsung_div_clock exynos5x_div_clks[] __initconst = { > DIV(CLK_DOUT_CLK2X_PHY0, "dout_clk2x_phy0", "dout_sclk_cdrex", > DIV_CDREX0, 3, 5), > > + DIV(0, "dout_pclk_drex0", "dout_cclk_drex0", DIV_CDREX0, 28, 3), > + > DIV(CLK_DOUT_PCLK_CORE_MEM, "dout_pclk_core_mem", "mout_mclk_cdrex", > DIV_CDREX1, 8, 3), > > @@ -1170,6 +1186,36 @@ static const struct samsung_gate_clock exynos5x_gate_clks[] __initconst = { > GATE_TOP_SCLK_ISP, 12, CLK_SET_RATE_PARENT, 0), > > GATE(CLK_G3D, "g3d", "mout_user_aclk_g3d", GATE_IP_G3D, 9, 0, 0), > + > + /* CDREX */ > + GATE(CLK_CLKM_PHY0, "clkm_phy0", "dout_sclk_cdrex", > + GATE_BUS_CDREX0, 0, 0, 0), > + GATE(CLK_CLKM_PHY1, "clkm_phy1", "dout_sclk_cdrex", > + GATE_BUS_CDREX0, 1, 0, 0), nitpick. Add the blank line because of clocks of the different register. > + GATE(0, "mx_mspll_ccore_phy", "mout_mx_mspll_ccore_phy", > + SRC_MASK_TOP7, 0, CLK_IGNORE_UNUSED, 0), > + > + GATE(CLK_ACLK_PPMU_DREX1_1, "aclk_ppmu_drex1_1", "dout_aclk_cdrex1", > + GATE_BUS_CDREX1, 12, CLK_IGNORE_UNUSED, 0), > + GATE(CLK_ACLK_PPMU_DREX1_0, "aclk_ppmu_drex1_0", "dout_aclk_cdrex1", > + GATE_BUS_CDREX1, 13, CLK_IGNORE_UNUSED, 0), > + GATE(CLK_ACLK_PPMU_DREX0_1, "aclk_ppmu_drex0_1", "dout_aclk_cdrex1", > + GATE_BUS_CDREX1, 14, CLK_IGNORE_UNUSED, 0), > + GATE(CLK_ACLK_PPMU_DREX0_0, "aclk_ppmu_drex0_0", "dout_aclk_cdrex1", > + GATE_BUS_CDREX1, 15, CLK_IGNORE_UNUSED, 0), > + > + GATE(CLK_PCLK_PPMU_DREX1_1, "pclk_ppmu_drex1_1", "dout_pclk_cdrex", > + GATE_BUS_CDREX1, 26, CLK_IGNORE_UNUSED, 0), > + GATE(CLK_PCLK_PPMU_DREX1_0, "pclk_ppmu_drex1_0", "dout_pclk_cdrex", > + GATE_BUS_CDREX1, 27, CLK_IGNORE_UNUSED, 0), > + GATE(CLK_PCLK_PPMU_DREX0_1, "pclk_ppmu_drex0_1", "dout_pclk_cdrex", > + GATE_BUS_CDREX1, 28, CLK_IGNORE_UNUSED, 0), > + GATE(CLK_PCLK_PPMU_DREX0_0, "pclk_ppmu_drex0_0", "dout_pclk_cdrex", > + GATE_BUS_CDREX1, 29, CLK_IGNORE_UNUSED, 0), > + > + GATE(CLK_CDREX_PAUSE, "clk_cdrex_pause", NULL, CDREX_PAUSE, 0, 0, 0), nitpick. Add the blank line because of clocks of the different register. > + GATE(CLK_CDREX_TIMING_SET, "clk_cdrex_timing_set", NULL, > + CDREX_LPDDR3PHY_CON3, 28, 0, 0), > }; > > static const struct samsung_div_clock exynos5x_disp_div_clks[] __initconst = { >
diff --git a/drivers/clk/samsung/clk-exynos5420.c b/drivers/clk/samsung/clk-exynos5420.c index 34cce3c..6da5875 100644 --- a/drivers/clk/samsung/clk-exynos5420.c +++ b/drivers/clk/samsung/clk-exynos5420.c @@ -134,6 +134,10 @@ #define SRC_CDREX 0x20200 #define DIV_CDREX0 0x20500 #define DIV_CDREX1 0x20504 +#define GATE_BUS_CDREX0 0x20700 +#define GATE_BUS_CDREX1 0x20704 +#define CDREX_PAUSE 0x2091c +#define CDREX_LPDDR3PHY_CON3 0x20a20 #define KPLL_LOCK 0x28000 #define KPLL_CON0 0x28100 #define SRC_KFC 0x28200 @@ -248,6 +252,10 @@ static const unsigned long exynos5x_clk_regs[] __initconst = { DIV_CDREX1, SRC_KFC, DIV_KFC0, + GATE_BUS_CDREX0, + GATE_BUS_CDREX1, + CDREX_PAUSE, + CDREX_LPDDR3PHY_CON3, }; static const unsigned long exynos5800_clk_regs[] __initconst = { @@ -425,6 +433,9 @@ PNAME(mout_group13_5800_p) = { "dout_osc_div", "mout_sw_aclkfl1_550_cam" }; PNAME(mout_group14_5800_p) = { "dout_aclk550_cam", "dout_sclk_sw" }; PNAME(mout_group15_5800_p) = { "dout_osc_div", "mout_sw_aclk550_cam" }; PNAME(mout_group16_5800_p) = { "dout_osc_div", "mout_mau_epll_clk" }; +PNAME(mout_mx_mspll_ccore_phy_p) = { "sclk_bpll", "mout_sclk_dpll", + "mout_sclk_mpll", "ff_dout_spll2", + "mout_sclk_spll", "mout_sclk_epll"}; /* fixed rate clocks generated outside the soc */ static struct samsung_fixed_rate_clock @@ -450,7 +461,7 @@ static const struct samsung_fixed_factor_clock static const struct samsung_fixed_factor_clock exynos5800_fixed_factor_clks[] __initconst = { FFACTOR(0, "ff_dout_epll2", "mout_sclk_epll", 1, 2, 0), - FFACTOR(0, "ff_dout_spll2", "mout_sclk_spll", 1, 2, 0), + FFACTOR(CLK_FF_DOUT_SPLL2, "ff_dout_spll2", "mout_sclk_spll", 1, 2, 0), }; static const struct samsung_mux_clock exynos5800_mux_clks[] __initconst = { @@ -472,11 +483,14 @@ static const struct samsung_mux_clock exynos5800_mux_clks[] __initconst = { MUX(0, "mout_aclk300_disp1", mout_group5_5800_p, SRC_TOP2, 24, 2), MUX(0, "mout_aclk300_gscl", mout_group5_5800_p, SRC_TOP2, 28, 2), + MUX(CLK_MOUT_MX_MSPLL_CCORE_PHY, "mout_mx_mspll_ccore_phy", + mout_mx_mspll_ccore_phy_p, SRC_TOP7, 0, 3), + MUX(CLK_MOUT_MX_MSPLL_CCORE, "mout_mx_mspll_ccore", - mout_mx_mspll_ccore_p, SRC_TOP7, 16, 2), + mout_mx_mspll_ccore_p, SRC_TOP7, 16, 3), MUX_F(CLK_MOUT_MAU_EPLL, "mout_mau_epll_clk", mout_mau_epll_clk_5800_p, SRC_TOP7, 20, 2, CLK_SET_RATE_PARENT, 0), - MUX(0, "sclk_bpll", mout_bpll_p, SRC_TOP7, 24, 1), + MUX(CLK_SCLK_BPLL, "sclk_bpll", mout_bpll_p, SRC_TOP7, 24, 1), MUX(0, "mout_epll2", mout_epll2_5800_p, SRC_TOP7, 28, 1), MUX(0, "mout_aclk550_cam", mout_group3_5800_p, SRC_TOP8, 16, 3), @@ -648,7 +662,7 @@ static const struct samsung_mux_clock exynos5x_mux_clks[] __initconst = { MUX(0, "mout_sclk_mpll", mout_mpll_p, SRC_TOP6, 0, 1), MUX(CLK_MOUT_VPLL, "mout_sclk_vpll", mout_vpll_p, SRC_TOP6, 4, 1), - MUX(0, "mout_sclk_spll", mout_spll_p, SRC_TOP6, 8, 1), + MUX(CLK_MOUT_SCLK_SPLL, "mout_sclk_spll", mout_spll_p, SRC_TOP6, 8, 1), MUX(0, "mout_sclk_ipll", mout_ipll_p, SRC_TOP6, 12, 1), MUX(0, "mout_sclk_rpll", mout_rpll_p, SRC_TOP6, 16, 1), MUX_F(CLK_MOUT_EPLL, "mout_sclk_epll", mout_epll_p, SRC_TOP6, 20, 1, @@ -817,6 +831,8 @@ static const struct samsung_div_clock exynos5x_div_clks[] __initconst = { DIV(CLK_DOUT_CLK2X_PHY0, "dout_clk2x_phy0", "dout_sclk_cdrex", DIV_CDREX0, 3, 5), + DIV(0, "dout_pclk_drex0", "dout_cclk_drex0", DIV_CDREX0, 28, 3), + DIV(CLK_DOUT_PCLK_CORE_MEM, "dout_pclk_core_mem", "mout_mclk_cdrex", DIV_CDREX1, 8, 3), @@ -1170,6 +1186,36 @@ static const struct samsung_gate_clock exynos5x_gate_clks[] __initconst = { GATE_TOP_SCLK_ISP, 12, CLK_SET_RATE_PARENT, 0), GATE(CLK_G3D, "g3d", "mout_user_aclk_g3d", GATE_IP_G3D, 9, 0, 0), + + /* CDREX */ + GATE(CLK_CLKM_PHY0, "clkm_phy0", "dout_sclk_cdrex", + GATE_BUS_CDREX0, 0, 0, 0), + GATE(CLK_CLKM_PHY1, "clkm_phy1", "dout_sclk_cdrex", + GATE_BUS_CDREX0, 1, 0, 0), + GATE(0, "mx_mspll_ccore_phy", "mout_mx_mspll_ccore_phy", + SRC_MASK_TOP7, 0, CLK_IGNORE_UNUSED, 0), + + GATE(CLK_ACLK_PPMU_DREX1_1, "aclk_ppmu_drex1_1", "dout_aclk_cdrex1", + GATE_BUS_CDREX1, 12, CLK_IGNORE_UNUSED, 0), + GATE(CLK_ACLK_PPMU_DREX1_0, "aclk_ppmu_drex1_0", "dout_aclk_cdrex1", + GATE_BUS_CDREX1, 13, CLK_IGNORE_UNUSED, 0), + GATE(CLK_ACLK_PPMU_DREX0_1, "aclk_ppmu_drex0_1", "dout_aclk_cdrex1", + GATE_BUS_CDREX1, 14, CLK_IGNORE_UNUSED, 0), + GATE(CLK_ACLK_PPMU_DREX0_0, "aclk_ppmu_drex0_0", "dout_aclk_cdrex1", + GATE_BUS_CDREX1, 15, CLK_IGNORE_UNUSED, 0), + + GATE(CLK_PCLK_PPMU_DREX1_1, "pclk_ppmu_drex1_1", "dout_pclk_cdrex", + GATE_BUS_CDREX1, 26, CLK_IGNORE_UNUSED, 0), + GATE(CLK_PCLK_PPMU_DREX1_0, "pclk_ppmu_drex1_0", "dout_pclk_cdrex", + GATE_BUS_CDREX1, 27, CLK_IGNORE_UNUSED, 0), + GATE(CLK_PCLK_PPMU_DREX0_1, "pclk_ppmu_drex0_1", "dout_pclk_cdrex", + GATE_BUS_CDREX1, 28, CLK_IGNORE_UNUSED, 0), + GATE(CLK_PCLK_PPMU_DREX0_0, "pclk_ppmu_drex0_0", "dout_pclk_cdrex", + GATE_BUS_CDREX1, 29, CLK_IGNORE_UNUSED, 0), + + GATE(CLK_CDREX_PAUSE, "clk_cdrex_pause", NULL, CDREX_PAUSE, 0, 0, 0), + GATE(CLK_CDREX_TIMING_SET, "clk_cdrex_timing_set", NULL, + CDREX_LPDDR3PHY_CON3, 28, 0, 0), }; static const struct samsung_div_clock exynos5x_disp_div_clks[] __initconst = {
This patch provides support for clocks needed for Dynamic Memory Controller in Exynos5422 SoC. It adds CDREX base register addresses, new DIV, MUX and GATE entries. Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com> --- drivers/clk/samsung/clk-exynos5420.c | 54 +++++++++++++++++++++++++++++++++--- 1 file changed, 50 insertions(+), 4 deletions(-)