| Message ID | 20190412203756.67329-1-venture@google.com (mailing list archive) |
|---|---|
| State | Accepted |
| Headers | show |
| Series | [v3] hwmon: (pmbus/ir38064): Add driver for Infineon IR38064 Voltage Regulator | expand |
On 4/12/19 1:37 PM, Patrick Venture wrote: > From: Maxim Sloyko <maxims@google.com> > > Add the pmbus driver for the Infineon ir38064 voltage regulator. > > VOUT_MODE is not supported by the device. The driver fakes linear16 > mode with exponent value -8. > > The device supports VOUT_PEAK, IOUT_PEAK, and TEMPERATURE_PEAK, however > this driver does not enable them. > I meant to add this into the driver as comment (where people can see it going forward). Never mind, I'll apply the patch and add it myself. Guenter > Signed-off-by: Maxim Sloyko <maxims@google.com> > Signed-off-by: Patrick Venture <venture@google.com> > --- > v3: > - Updated commit message to indicate behaviors. > v2: > - Cleaned up weird tabbing behavior in doc. > v1: > - Initial patchset. > --- > Documentation/hwmon/ir38064 | 64 +++++++++++++++++++++++++++++++++++ > drivers/hwmon/pmbus/Kconfig | 9 +++++ > drivers/hwmon/pmbus/Makefile | 1 + > drivers/hwmon/pmbus/ir38064.c | 60 ++++++++++++++++++++++++++++++++ > 4 files changed, 134 insertions(+) > create mode 100644 Documentation/hwmon/ir38064 > create mode 100644 drivers/hwmon/pmbus/ir38064.c > > diff --git a/Documentation/hwmon/ir38064 b/Documentation/hwmon/ir38064 > new file mode 100644 > index 0000000000000..618779a329da0 > --- /dev/null > +++ b/Documentation/hwmon/ir38064 > @@ -0,0 +1,64 @@ > +Kernel driver ir38064 > +===================== > + > +Supported chips: > + * Infineon IR38064 > + Prefix: 'ir38064' > + Addresses scanned: - > + Datasheet: Publicly available at the Infineon webiste > + https://www.infineon.com/dgdl/Infineon-IR38064MTRPBF-DS-v03_07-EN.pdf?fileId=5546d462584d1d4a0158db0d9efb67ca > + > +Datasheet is not publicly available. > + > + > +Authors: > + Maxim Sloyko <maxims@google.com> > + Patrick Venture <venture@google.com> > + > +Description > +----------- > + > +IR38064 is a Single-input Voltage, Synchronous Buck Regulator, DC-DC Converter. > + > +Usage Notes > +----------- > + > +This driver does not probe for PMBus devices. You will have to instantiate > +devices explicitly. > + > +Sysfs attributes > +---------------- > + > +curr1_label "iout1" > +curr1_input Measured output current > +curr1_crit Critical maximum current > +curr1_crit_alarm Current critical high alarm > +curr1_max Maximum current > +curr1_max_alarm Current high alarm > + > +in1_label "vin" > +in1_input Measured input voltage > +in1_crit Critical maximum input voltage > +in1_crit_alarm Input voltage critical high alarm > +in1_min Minimum input voltage > +in1_min_alarm Input voltage low alarm > + > +in2_label "vout1" > +in2_input Measured output voltage > +in2_lcrit Critical minimum output voltage > +in2_lcrit_alarm Output voltage critical low alarm > +in2_crit Critical maximum output voltage > +in2_crit_alarm Output voltage critical high alarm > +in2_max Maximum output voltage > +in2_max_alarm Output voltage high alarm > +in2_min Minimum output voltage > +in2_min_alarm Output voltage low alarm > + > +power1_label "pout1" > +power1_input Measured output power > + > +temp1_input Measured temperature > +temp1_crit Critical high temperature > +temp1_crit_alarm Chip temperature critical high alarm > +temp1_max Maximum temperature > +temp1_max_alarm Chip temperature high alarm > diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig > index 629cb45f8557a..de87abab990e5 100644 > --- a/drivers/hwmon/pmbus/Kconfig > +++ b/drivers/hwmon/pmbus/Kconfig > @@ -54,6 +54,15 @@ config SENSORS_IR35221 > This driver can also be built as a module. If so, the module will > be called ir35521. > > +config SENSORS_IR38064 > + tristate "Infineon IR38064" > + help > + If you say yes here you get hardware monitoring support for Infineon > + IR38064. > + > + This driver can also be built as a module. If so, the module will > + be called ir38064. > + > config SENSORS_LM25066 > tristate "National Semiconductor LM25066 and compatibles" > help > diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile > index ea0e39518c216..7d1fa6b3c8c93 100644 > --- a/drivers/hwmon/pmbus/Makefile > +++ b/drivers/hwmon/pmbus/Makefile > @@ -8,6 +8,7 @@ obj-$(CONFIG_SENSORS_PMBUS) += pmbus.o > obj-$(CONFIG_SENSORS_ADM1275) += adm1275.o > obj-$(CONFIG_SENSORS_IBM_CFFPS) += ibm-cffps.o > obj-$(CONFIG_SENSORS_IR35221) += ir35221.o > +obj-$(CONFIG_SENSORS_IR38064) += ir38064.o > obj-$(CONFIG_SENSORS_LM25066) += lm25066.o > obj-$(CONFIG_SENSORS_LTC2978) += ltc2978.o > obj-$(CONFIG_SENSORS_LTC3815) += ltc3815.o > diff --git a/drivers/hwmon/pmbus/ir38064.c b/drivers/hwmon/pmbus/ir38064.c > new file mode 100644 > index 0000000000000..4b957ebb6fa71 > --- /dev/null > +++ b/drivers/hwmon/pmbus/ir38064.c > @@ -0,0 +1,60 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * Hardware monitoring driver for Infineon IR38064 > + * > + * Copyright (c) 2017 Google Inc > + * > + */ > + > +#include <linux/err.h> > +#include <linux/i2c.h> > +#include <linux/init.h> > +#include <linux/kernel.h> > +#include <linux/module.h> > +#include "pmbus.h" > + > +static struct pmbus_driver_info ir38064_info = { > + .pages = 1, > + .format[PSC_VOLTAGE_IN] = linear, > + .format[PSC_VOLTAGE_OUT] = direct, > + .format[PSC_CURRENT_OUT] = linear, > + .format[PSC_POWER] = linear, > + .format[PSC_TEMPERATURE] = linear, > + .m[PSC_VOLTAGE_OUT] = 256, > + .b[PSC_VOLTAGE_OUT] = 0, > + .R[PSC_VOLTAGE_OUT] = 0, > + .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_STATUS_INPUT > + | PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP > + | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT > + | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT > + | PMBUS_HAVE_POUT, > +}; > + > +static int ir38064_probe(struct i2c_client *client, > + const struct i2c_device_id *id) > +{ > + return pmbus_do_probe(client, id, &ir38064_info); > +} > + > +static const struct i2c_device_id ir38064_id[] = { > + {"ir38064", 0}, > + {} > +}; > + > +MODULE_DEVICE_TABLE(i2c, ir38064_id); > + > +/* This is the driver that will be inserted */ > +static struct i2c_driver ir38064_driver = { > + .driver = { > + .name = "ir38064", > + }, > + .probe = ir38064_probe, > + .remove = pmbus_do_remove, > + .id_table = ir38064_id, > +}; > + > +module_i2c_driver(ir38064_driver); > + > +MODULE_AUTHOR("Maxim Sloyko <maxims@google.com>"); > +MODULE_DESCRIPTION("PMBus driver for Infineon IR38064"); > +MODULE_LICENSE("GPL"); >
On Fri, Apr 12, 2019 at 3:15 PM Guenter Roeck <linux@roeck-us.net> wrote: > > On 4/12/19 1:37 PM, Patrick Venture wrote: > > From: Maxim Sloyko <maxims@google.com> > > > > Add the pmbus driver for the Infineon ir38064 voltage regulator. > > > > VOUT_MODE is not supported by the device. The driver fakes linear16 > > mode with exponent value -8. > > > > The device supports VOUT_PEAK, IOUT_PEAK, and TEMPERATURE_PEAK, however > > this driver does not enable them. > > > > I meant to add this into the driver as comment (where people can see it > going forward). Never mind, I'll apply the patch and add it myself. Sorry, I definitely misunderstood your intent. Thanks for handling it. > > Guenter > > > Signed-off-by: Maxim Sloyko <maxims@google.com> > > Signed-off-by: Patrick Venture <venture@google.com> > > --- > > v3: > > - Updated commit message to indicate behaviors. > > v2: > > - Cleaned up weird tabbing behavior in doc. > > v1: > > - Initial patchset. > > --- > > Documentation/hwmon/ir38064 | 64 +++++++++++++++++++++++++++++++++++ > > drivers/hwmon/pmbus/Kconfig | 9 +++++ > > drivers/hwmon/pmbus/Makefile | 1 + > > drivers/hwmon/pmbus/ir38064.c | 60 ++++++++++++++++++++++++++++++++ > > 4 files changed, 134 insertions(+) > > create mode 100644 Documentation/hwmon/ir38064 > > create mode 100644 drivers/hwmon/pmbus/ir38064.c > > > > diff --git a/Documentation/hwmon/ir38064 b/Documentation/hwmon/ir38064 > > new file mode 100644 > > index 0000000000000..618779a329da0 > > --- /dev/null > > +++ b/Documentation/hwmon/ir38064 > > @@ -0,0 +1,64 @@ > > +Kernel driver ir38064 > > +===================== > > + > > +Supported chips: > > + * Infineon IR38064 > > + Prefix: 'ir38064' > > + Addresses scanned: - > > + Datasheet: Publicly available at the Infineon webiste > > + https://www.infineon.com/dgdl/Infineon-IR38064MTRPBF-DS-v03_07-EN.pdf?fileId=5546d462584d1d4a0158db0d9efb67ca > > + > > +Datasheet is not publicly available. > > + > > + > > +Authors: > > + Maxim Sloyko <maxims@google.com> > > + Patrick Venture <venture@google.com> > > + > > +Description > > +----------- > > + > > +IR38064 is a Single-input Voltage, Synchronous Buck Regulator, DC-DC Converter. > > + > > +Usage Notes > > +----------- > > + > > +This driver does not probe for PMBus devices. You will have to instantiate > > +devices explicitly. > > + > > +Sysfs attributes > > +---------------- > > + > > +curr1_label "iout1" > > +curr1_input Measured output current > > +curr1_crit Critical maximum current > > +curr1_crit_alarm Current critical high alarm > > +curr1_max Maximum current > > +curr1_max_alarm Current high alarm > > + > > +in1_label "vin" > > +in1_input Measured input voltage > > +in1_crit Critical maximum input voltage > > +in1_crit_alarm Input voltage critical high alarm > > +in1_min Minimum input voltage > > +in1_min_alarm Input voltage low alarm > > + > > +in2_label "vout1" > > +in2_input Measured output voltage > > +in2_lcrit Critical minimum output voltage > > +in2_lcrit_alarm Output voltage critical low alarm > > +in2_crit Critical maximum output voltage > > +in2_crit_alarm Output voltage critical high alarm > > +in2_max Maximum output voltage > > +in2_max_alarm Output voltage high alarm > > +in2_min Minimum output voltage > > +in2_min_alarm Output voltage low alarm > > + > > +power1_label "pout1" > > +power1_input Measured output power > > + > > +temp1_input Measured temperature > > +temp1_crit Critical high temperature > > +temp1_crit_alarm Chip temperature critical high alarm > > +temp1_max Maximum temperature > > +temp1_max_alarm Chip temperature high alarm > > diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig > > index 629cb45f8557a..de87abab990e5 100644 > > --- a/drivers/hwmon/pmbus/Kconfig > > +++ b/drivers/hwmon/pmbus/Kconfig > > @@ -54,6 +54,15 @@ config SENSORS_IR35221 > > This driver can also be built as a module. If so, the module will > > be called ir35521. > > > > +config SENSORS_IR38064 > > + tristate "Infineon IR38064" > > + help > > + If you say yes here you get hardware monitoring support for Infineon > > + IR38064. > > + > > + This driver can also be built as a module. If so, the module will > > + be called ir38064. > > + > > config SENSORS_LM25066 > > tristate "National Semiconductor LM25066 and compatibles" > > help > > diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile > > index ea0e39518c216..7d1fa6b3c8c93 100644 > > --- a/drivers/hwmon/pmbus/Makefile > > +++ b/drivers/hwmon/pmbus/Makefile > > @@ -8,6 +8,7 @@ obj-$(CONFIG_SENSORS_PMBUS) += pmbus.o > > obj-$(CONFIG_SENSORS_ADM1275) += adm1275.o > > obj-$(CONFIG_SENSORS_IBM_CFFPS) += ibm-cffps.o > > obj-$(CONFIG_SENSORS_IR35221) += ir35221.o > > +obj-$(CONFIG_SENSORS_IR38064) += ir38064.o > > obj-$(CONFIG_SENSORS_LM25066) += lm25066.o > > obj-$(CONFIG_SENSORS_LTC2978) += ltc2978.o > > obj-$(CONFIG_SENSORS_LTC3815) += ltc3815.o > > diff --git a/drivers/hwmon/pmbus/ir38064.c b/drivers/hwmon/pmbus/ir38064.c > > new file mode 100644 > > index 0000000000000..4b957ebb6fa71 > > --- /dev/null > > +++ b/drivers/hwmon/pmbus/ir38064.c > > @@ -0,0 +1,60 @@ > > +// SPDX-License-Identifier: GPL-2.0+ > > +/* > > + * Hardware monitoring driver for Infineon IR38064 > > + * > > + * Copyright (c) 2017 Google Inc > > + * > > + */ > > + > > +#include <linux/err.h> > > +#include <linux/i2c.h> > > +#include <linux/init.h> > > +#include <linux/kernel.h> > > +#include <linux/module.h> > > +#include "pmbus.h" > > + > > +static struct pmbus_driver_info ir38064_info = { > > + .pages = 1, > > + .format[PSC_VOLTAGE_IN] = linear, > > + .format[PSC_VOLTAGE_OUT] = direct, > > + .format[PSC_CURRENT_OUT] = linear, > > + .format[PSC_POWER] = linear, > > + .format[PSC_TEMPERATURE] = linear, > > + .m[PSC_VOLTAGE_OUT] = 256, > > + .b[PSC_VOLTAGE_OUT] = 0, > > + .R[PSC_VOLTAGE_OUT] = 0, > > + .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_STATUS_INPUT > > + | PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP > > + | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT > > + | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT > > + | PMBUS_HAVE_POUT, > > +}; > > + > > +static int ir38064_probe(struct i2c_client *client, > > + const struct i2c_device_id *id) > > +{ > > + return pmbus_do_probe(client, id, &ir38064_info); > > +} > > + > > +static const struct i2c_device_id ir38064_id[] = { > > + {"ir38064", 0}, > > + {} > > +}; > > + > > +MODULE_DEVICE_TABLE(i2c, ir38064_id); > > + > > +/* This is the driver that will be inserted */ > > +static struct i2c_driver ir38064_driver = { > > + .driver = { > > + .name = "ir38064", > > + }, > > + .probe = ir38064_probe, > > + .remove = pmbus_do_remove, > > + .id_table = ir38064_id, > > +}; > > + > > +module_i2c_driver(ir38064_driver); > > + > > +MODULE_AUTHOR("Maxim Sloyko <maxims@google.com>"); > > +MODULE_DESCRIPTION("PMBus driver for Infineon IR38064"); > > +MODULE_LICENSE("GPL"); > > >
diff --git a/Documentation/hwmon/ir38064 b/Documentation/hwmon/ir38064 new file mode 100644 index 0000000000000..618779a329da0 --- /dev/null +++ b/Documentation/hwmon/ir38064 @@ -0,0 +1,64 @@ +Kernel driver ir38064 +===================== + +Supported chips: + * Infineon IR38064 + Prefix: 'ir38064' + Addresses scanned: - + Datasheet: Publicly available at the Infineon webiste + https://www.infineon.com/dgdl/Infineon-IR38064MTRPBF-DS-v03_07-EN.pdf?fileId=5546d462584d1d4a0158db0d9efb67ca + +Datasheet is not publicly available. + + +Authors: + Maxim Sloyko <maxims@google.com> + Patrick Venture <venture@google.com> + +Description +----------- + +IR38064 is a Single-input Voltage, Synchronous Buck Regulator, DC-DC Converter. + +Usage Notes +----------- + +This driver does not probe for PMBus devices. You will have to instantiate +devices explicitly. + +Sysfs attributes +---------------- + +curr1_label "iout1" +curr1_input Measured output current +curr1_crit Critical maximum current +curr1_crit_alarm Current critical high alarm +curr1_max Maximum current +curr1_max_alarm Current high alarm + +in1_label "vin" +in1_input Measured input voltage +in1_crit Critical maximum input voltage +in1_crit_alarm Input voltage critical high alarm +in1_min Minimum input voltage +in1_min_alarm Input voltage low alarm + +in2_label "vout1" +in2_input Measured output voltage +in2_lcrit Critical minimum output voltage +in2_lcrit_alarm Output voltage critical low alarm +in2_crit Critical maximum output voltage +in2_crit_alarm Output voltage critical high alarm +in2_max Maximum output voltage +in2_max_alarm Output voltage high alarm +in2_min Minimum output voltage +in2_min_alarm Output voltage low alarm + +power1_label "pout1" +power1_input Measured output power + +temp1_input Measured temperature +temp1_crit Critical high temperature +temp1_crit_alarm Chip temperature critical high alarm +temp1_max Maximum temperature +temp1_max_alarm Chip temperature high alarm diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig index 629cb45f8557a..de87abab990e5 100644 --- a/drivers/hwmon/pmbus/Kconfig +++ b/drivers/hwmon/pmbus/Kconfig @@ -54,6 +54,15 @@ config SENSORS_IR35221 This driver can also be built as a module. If so, the module will be called ir35521. +config SENSORS_IR38064 + tristate "Infineon IR38064" + help + If you say yes here you get hardware monitoring support for Infineon + IR38064. + + This driver can also be built as a module. If so, the module will + be called ir38064. + config SENSORS_LM25066 tristate "National Semiconductor LM25066 and compatibles" help diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile index ea0e39518c216..7d1fa6b3c8c93 100644 --- a/drivers/hwmon/pmbus/Makefile +++ b/drivers/hwmon/pmbus/Makefile @@ -8,6 +8,7 @@ obj-$(CONFIG_SENSORS_PMBUS) += pmbus.o obj-$(CONFIG_SENSORS_ADM1275) += adm1275.o obj-$(CONFIG_SENSORS_IBM_CFFPS) += ibm-cffps.o obj-$(CONFIG_SENSORS_IR35221) += ir35221.o +obj-$(CONFIG_SENSORS_IR38064) += ir38064.o obj-$(CONFIG_SENSORS_LM25066) += lm25066.o obj-$(CONFIG_SENSORS_LTC2978) += ltc2978.o obj-$(CONFIG_SENSORS_LTC3815) += ltc3815.o diff --git a/drivers/hwmon/pmbus/ir38064.c b/drivers/hwmon/pmbus/ir38064.c new file mode 100644 index 0000000000000..4b957ebb6fa71 --- /dev/null +++ b/drivers/hwmon/pmbus/ir38064.c @@ -0,0 +1,60 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Hardware monitoring driver for Infineon IR38064 + * + * Copyright (c) 2017 Google Inc + * + */ + +#include <linux/err.h> +#include <linux/i2c.h> +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include "pmbus.h" + +static struct pmbus_driver_info ir38064_info = { + .pages = 1, + .format[PSC_VOLTAGE_IN] = linear, + .format[PSC_VOLTAGE_OUT] = direct, + .format[PSC_CURRENT_OUT] = linear, + .format[PSC_POWER] = linear, + .format[PSC_TEMPERATURE] = linear, + .m[PSC_VOLTAGE_OUT] = 256, + .b[PSC_VOLTAGE_OUT] = 0, + .R[PSC_VOLTAGE_OUT] = 0, + .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_STATUS_INPUT + | PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP + | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT + | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT + | PMBUS_HAVE_POUT, +}; + +static int ir38064_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + return pmbus_do_probe(client, id, &ir38064_info); +} + +static const struct i2c_device_id ir38064_id[] = { + {"ir38064", 0}, + {} +}; + +MODULE_DEVICE_TABLE(i2c, ir38064_id); + +/* This is the driver that will be inserted */ +static struct i2c_driver ir38064_driver = { + .driver = { + .name = "ir38064", + }, + .probe = ir38064_probe, + .remove = pmbus_do_remove, + .id_table = ir38064_id, +}; + +module_i2c_driver(ir38064_driver); + +MODULE_AUTHOR("Maxim Sloyko <maxims@google.com>"); +MODULE_DESCRIPTION("PMBus driver for Infineon IR38064"); +MODULE_LICENSE("GPL");