| Message ID | 20190413165418.27880-6-megous@megous.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | Add support for Orange Pi 3 | expand |
On Sat, Apr 13, 2019 at 10:24 PM megous via linux-sunxi <linux-sunxi@googlegroups.com> wrote: > > From: Ondrej Jirman <megous@megous.com> > > Orange Pi 3 has two regulators that power the Realtek RTL8211E. According > to the phy datasheet, both regulators need to be enabled at the same time, > but we can only specify a single phy-supply in the DT. > > This can be achieved by making one regulator depedning on the other via > vin-supply. While it's not a technically correct description of the > hardware, it achieves the purpose. > > All values of RX/TX delay were tested exhaustively and a middle one of the > working values was chosen. > > Signed-off-by: Ondrej Jirman <megous@megous.com> > --- > .../dts/allwinner/sun50i-h6-orangepi-3.dts | 44 +++++++++++++++++++ > 1 file changed, 44 insertions(+) > > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts > index 17d496990108..6d6b1f66796d 100644 > --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts > @@ -15,6 +15,7 @@ > > aliases { > serial0 = &uart0; > + ethernet0 = &emac; > }; > > chosen { > @@ -44,6 +45,27 @@ > regulator-max-microvolt = <5000000>; > regulator-always-on; > }; > + > + /* > + * The board uses 2.5V RGMII signalling. Power sequence to enable > + * the phy is to enable GMAC-2V5 and GMAC-3V3 (aldo2) power rails > + * at the same time and to wait 100ms. > + */ > + reg_gmac_2v5: gmac-2v5 { > + compatible = "regulator-fixed"; > + regulator-name = "gmac-2v5"; > + regulator-min-microvolt = <2500000>; > + regulator-max-microvolt = <2500000>; > + startup-delay-us = <100000>; > + enable-active-high; > + gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */ > + > + /* The real parent of gmac-2v5 is reg_vcc5v, but we need to > + * enable two regulators to power the phy. This is one way > + * to achieve that. > + */ > + vin-supply = <®_aldo2>; /* GMAC-3V3 */ The actual output supply pin name is GMAC-3V which has an input of VCC3V3-MAC (ie aldo2), if we compatible to schematics better to use the same, IMHO.
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts index 17d496990108..6d6b1f66796d 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts @@ -15,6 +15,7 @@ aliases { serial0 = &uart0; + ethernet0 = &emac; }; chosen { @@ -44,6 +45,27 @@ regulator-max-microvolt = <5000000>; regulator-always-on; }; + + /* + * The board uses 2.5V RGMII signalling. Power sequence to enable + * the phy is to enable GMAC-2V5 and GMAC-3V3 (aldo2) power rails + * at the same time and to wait 100ms. + */ + reg_gmac_2v5: gmac-2v5 { + compatible = "regulator-fixed"; + regulator-name = "gmac-2v5"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + startup-delay-us = <100000>; + enable-active-high; + gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */ + + /* The real parent of gmac-2v5 is reg_vcc5v, but we need to + * enable two regulators to power the phy. This is one way + * to achieve that. + */ + vin-supply = <®_aldo2>; /* GMAC-3V3 */ + }; }; &cpu0 { @@ -58,6 +80,28 @@ status = "okay"; }; +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&ext_rgmii_pins>; + phy-mode = "rgmii"; + phy-handle = <&ext_rgmii_phy>; + phy-supply = <®_gmac_2v5>; + allwinner,rx-delay-ps = <1500>; + allwinner,tx-delay-ps = <700>; + status = "okay"; +}; + +&mdio { + ext_rgmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + + reset-gpios = <&pio 3 14 GPIO_ACTIVE_LOW>; /* PD14 */ + reset-assert-us = <15000>; + reset-deassert-us = <40000>; + }; +}; + &mmc0 { vmmc-supply = <®_cldo1>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */