diff mbox series

[17/19] aspeed/smc: add DMA calibration settings

Message ID 20190525151241.5017-18-clg@kaod.org (mailing list archive)
State New, archived
Headers show
Series aspeed: machine extensions and fixes | expand

Commit Message

Cédric Le Goater May 25, 2019, 3:12 p.m. UTC
When doing calibration, the SPI clock rate in the CE0 Control Register
and the read delay cycles in the Read Timing Compensation Register are
set using bit[11:4] of the DMA Control Register.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
---
 hw/ssi/aspeed_smc.c | 64 ++++++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 63 insertions(+), 1 deletion(-)

Comments

Joel Stanley June 12, 2019, 1:40 a.m. UTC | #1
On Sat, 25 May 2019 at 15:14, Cédric Le Goater <clg@kaod.org> wrote:
>
> When doing calibration, the SPI clock rate in the CE0 Control Register
> and the read delay cycles in the Read Timing Compensation Register are
> set using bit[11:4] of the DMA Control Register.
>
> Signed-off-by: Cédric Le Goater <clg@kaod.org>

Acked-by: Joel Stanley <joel@jms.id.au>
diff mbox series

Patch

diff --git a/hw/ssi/aspeed_smc.c b/hw/ssi/aspeed_smc.c
index b3c8e0a84f8b..406c30c60b3f 100644
--- a/hw/ssi/aspeed_smc.c
+++ b/hw/ssi/aspeed_smc.c
@@ -74,6 +74,10 @@ 
 #define   CTRL_CMD_MASK            0xff
 #define   CTRL_DUMMY_HIGH_SHIFT    14
 #define   CTRL_AST2400_SPI_4BYTE   (1 << 13)
+#define CE_CTRL_CLOCK_FREQ_SHIFT   8
+#define CE_CTRL_CLOCK_FREQ_MASK    0xf
+#define CE_CTRL_CLOCK_FREQ(div)                                         \
+    (((div) & CE_CTRL_CLOCK_FREQ_MASK) << CE_CTRL_CLOCK_FREQ_SHIFT)
 #define   CTRL_DUMMY_LOW_SHIFT     6 /* 2 bits [7:6] */
 #define   CTRL_CE_STOP_ACTIVE      (1 << 2)
 #define   CTRL_CMD_MODE_MASK       0x3
@@ -109,7 +113,7 @@ 
 #define   DMA_CTRL_DELAY_SHIFT  8
 #define   DMA_CTRL_FREQ_MASK    0xf
 #define   DMA_CTRL_FREQ_SHIFT   4
-#define   DMA_CTRL_MODE         (1 << 3)
+#define   DMA_CTRL_CALIB        (1 << 3)
 #define   DMA_CTRL_CKSUM        (1 << 2)
 #define   DMA_CTRL_WRITE        (1 << 1)
 #define   DMA_CTRL_ENABLE       (1 << 0)
@@ -808,6 +812,60 @@  static uint64_t aspeed_smc_read(void *opaque, hwaddr addr, unsigned int size)
     }
 }
 
+static uint8_t aspeed_smc_hclk_divisor(uint8_t hclk_mask)
+{
+    /* HCLK/1 .. HCLK/16 */
+    const uint8_t hclk_divisors[] = {
+        15, 7, 14, 6, 13, 5, 12, 4, 11, 3, 10, 2, 9, 1, 8, 0
+    };
+    int i;
+
+    for (i = 0; i < ARRAY_SIZE(hclk_divisors); i++) {
+        if (hclk_mask == hclk_divisors[i]) {
+            return i + 1;
+        }
+    }
+
+    qemu_log_mask(LOG_GUEST_ERROR, "invalid HCLK mask %x", hclk_mask);
+    return 0;
+}
+
+/*
+ * When doing calibration, the SPI clock rate in the CE0 Control
+ * Register and the read delay cycles in the Read Timing Compensation
+ * Register are set using bit[11:4] of the DMA Control Register.
+ */
+static void aspeed_smc_dma_calibration(AspeedSMCState *s)
+{
+    uint8_t delay =
+        (s->regs[R_DMA_CTRL] >> DMA_CTRL_DELAY_SHIFT) & DMA_CTRL_DELAY_MASK;
+    uint8_t hclk_mask =
+        (s->regs[R_DMA_CTRL] >> DMA_CTRL_FREQ_SHIFT) & DMA_CTRL_FREQ_MASK;
+    uint8_t hclk_div = aspeed_smc_hclk_divisor(hclk_mask);
+    uint32_t hclk_shift = (hclk_div - 1) << 2;
+    uint8_t cs;
+
+    /*
+     * The Read Timing Compensation Register values apply to all CS on
+     * the SPI bus and only HCLK/1 - HCLK/5 can have tunable delays
+     */
+    if (hclk_div && hclk_div < 6) {
+        s->regs[s->r_timings] &= ~(0xf << hclk_shift);
+        s->regs[s->r_timings] |= delay << hclk_shift;
+    }
+
+    /*
+     * TODO: compute the CS from the DMA address and the segment
+     * registers. This is not really a problem for now because the
+     * Timing Register values apply to all CS and software uses CS0 to
+     * do calibration.
+     */
+    cs = 0;
+    s->regs[s->r_ctrl0 + cs] &=
+        ~(CE_CTRL_CLOCK_FREQ_MASK << CE_CTRL_CLOCK_FREQ_SHIFT);
+    s->regs[s->r_ctrl0 + cs] |= CE_CTRL_CLOCK_FREQ(hclk_div);
+}
+
 /*
  * Accumulate the result of the reads to provide a checksum that will
  * be used to validate the read timing settings.
@@ -823,6 +881,10 @@  static void aspeed_smc_dma_checksum(AspeedSMCState *s)
         return;
     }
 
+    if (s->regs[R_DMA_CTRL] & DMA_CTRL_CALIB) {
+        aspeed_smc_dma_calibration(s);
+    }
+
     while (s->regs[R_DMA_LEN]) {
         result = address_space_read(&s->flash_as, s->regs[R_DMA_FLASH_ADDR],
                                     MEMTXATTRS_UNSPECIFIED,