| Message ID | 20190715182856.21688-17-jagan@amarulasolutions.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | ram: rk3399: Add rank detection | expand |
On 2019/7/16 上午2:28, Jagan Teki wrote: > Right now the rk3399 sdram driver assume that the board > has configured with 2 channels, so any possibility to > enable single channel on the same driver will encounter > channel #1 data training failure. > > Log: > U-Boot TPL board init > sdram_init: data training failed > rk3399_dmc_init DRAM init failed -5 > > So, add an algorithm that can capable to compute the active > or configured rank with associated channel like > a) do rank loop to compute the active rank, with associated > channel numbers > b) then, succeed the data training only for configured channel > c) preserve the rank for given channel > d) do channel loop for setting the active channel > e) if given rank is zero or inactive on the specific channel, > clear the timings for the associated channel > f) finally, return error if number of channels is zero > > Tested in NanoPI-NEO4 since it support single channel sdram > configuration. > > Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> > Signed-off-by: YouMin Chen <cym@rock-chips.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com> Thanks, - Kever > --- > drivers/ram/rockchip/sdram_rk3399.c | 110 ++++++++++++++++++++++------ > 1 file changed, 86 insertions(+), 24 deletions(-) > > diff --git a/drivers/ram/rockchip/sdram_rk3399.c b/drivers/ram/rockchip/sdram_rk3399.c > index 8bbacb5275..b83955f94e 100644 > --- a/drivers/ram/rockchip/sdram_rk3399.c > +++ b/drivers/ram/rockchip/sdram_rk3399.c > @@ -1254,13 +1254,52 @@ static unsigned char calculate_stride(struct rk3399_sdram_params *params) > return stride; > } > > +static void clear_channel_params(struct rk3399_sdram_params *params, u8 channel) > +{ > + params->ch[channel].cap_info.rank = 0; > + params->ch[channel].cap_info.col = 0; > + params->ch[channel].cap_info.bk = 0; > + params->ch[channel].cap_info.bw = 32; > + params->ch[channel].cap_info.dbw = 32; > + params->ch[channel].cap_info.row_3_4 = 0; > + params->ch[channel].cap_info.cs0_row = 0; > + params->ch[channel].cap_info.cs1_row = 0; > + params->ch[channel].cap_info.ddrconfig = 0; > +} > + > +static int pctl_init(struct dram_info *dram, struct rk3399_sdram_params *params) > +{ > + int channel; > + int ret; > + > + for (channel = 0; channel < 2; channel++) { > + const struct chan_info *chan = &dram->chan[channel]; > + struct rk3399_cru *cru = dram->cru; > + struct rk3399_ddr_publ_regs *publ = chan->publ; > + > + phy_pctrl_reset(cru, channel); > + phy_dll_bypass_set(publ, params->base.ddr_freq); > + > + ret = pctl_cfg(dram, chan, channel, params); > + if (ret < 0) { > + printf("%s: pctl config failed\n", __func__); > + return ret; > + } > + > + /* start to trigger initialization */ > + pctl_start(dram, channel); > + } > + > + return 0; > +} > + > static int sdram_init(struct dram_info *dram, > struct rk3399_sdram_params *params) > { > unsigned char dramtype = params->base.dramtype; > unsigned int ddr_freq = params->base.ddr_freq; > - struct rk3399_cru *cru = dram->cru; > - int channel; > + u32 training_flag = PI_READ_GATE_TRAINING; > + int channel, ch, rank; > int ret; > > debug("Starting SDRAM initialization...\n"); > @@ -1272,36 +1311,59 @@ static int sdram_init(struct dram_info *dram, > return -E2BIG; > } > > - for (channel = 0; channel < 2; channel++) { > - const struct chan_info *chan = &dram->chan[channel]; > - struct rk3399_ddr_publ_regs *publ = chan->publ; > + for (ch = 0; ch < 2; ch++) { > + params->ch[ch].cap_info.rank = 2; > + for (rank = 2; rank != 0; rank--) { > + ret = pctl_init(dram, params); > + if (ret < 0) { > + printf("%s: pctl init failed\n", __func__); > + return ret; > + } > > - phy_pctrl_reset(cru, channel); > - phy_dll_bypass_set(publ, ddr_freq); > + /* LPDDR2/LPDDR3 need to wait DAI complete, max 10us */ > + if (dramtype == LPDDR3) > + udelay(10); > > - if (channel >= params->base.num_channels) > - continue; > + params->ch[ch].cap_info.rank = rank; > > - ret = pctl_cfg(dram, chan, channel, params); > - if (ret < 0) { > - printf("%s: pctl config failed\n", __func__); > - return ret; > - } > + /* > + * LPDDR3 CA training msut be trigger before > + * other training. > + * DDR3 is not have CA training. > + */ > + if (params->base.dramtype == LPDDR3) > + training_flag |= PI_CA_TRAINING; > > - /* start to trigger initialization */ > - pctl_start(dram, channel); > + if (!(data_training(&dram->chan[ch], ch, > + params, training_flag))) > + break; > + } > + /* Computed rank with associated channel number */ > + params->ch[ch].cap_info.rank = rank; > + } > > - /* LPDDR2/LPDDR3 need to wait DAI complete, max 10us */ > - if (dramtype == LPDDR3) > - udelay(10); > + params->base.num_channels = 0; > + for (channel = 0; channel < 2; channel++) { > + const struct chan_info *chan = &dram->chan[channel]; > + struct sdram_cap_info *cap_info = ¶ms->ch[channel].cap_info; > > - if (data_training(chan, channel, params, PI_FULL_TRAINING)) { > - printf("%s: data training failed\n", __func__); > - return -EIO; > + if (cap_info->rank == 0) { > + clear_channel_params(params, channel); > + continue; > + } else { > + params->base.num_channels++; > } > > - set_ddrconfig(chan, params, channel, > - params->ch[channel].cap_info.ddrconfig); > + debug("Channel "); > + debug(channel ? "1: " : "0: "); > + > + set_ddrconfig(chan, params, channel, cap_info->ddrconfig); > + } > + > + if (params->base.num_channels == 0) { > + printf("%s: ", __func__); > + printf(" - %dMHz failed!\n", params->base.ddr_freq); > + return -EINVAL; > } > > params->base.stride = calculate_stride(params);
Hi Jagan, I'm sure this patch have some problem with evb-rk3399, which I think make the ddr not init correctly and error happen in ATF. Please help to check the detail of this patch, you can send new version of this patch only to mailing list and I will replace it to older version. Thanks, - Kever On 2019/7/16 上午2:28, Jagan Teki wrote: > Right now the rk3399 sdram driver assume that the board > has configured with 2 channels, so any possibility to > enable single channel on the same driver will encounter > channel #1 data training failure. > > Log: > U-Boot TPL board init > sdram_init: data training failed > rk3399_dmc_init DRAM init failed -5 > > So, add an algorithm that can capable to compute the active > or configured rank with associated channel like > a) do rank loop to compute the active rank, with associated > channel numbers > b) then, succeed the data training only for configured channel > c) preserve the rank for given channel > d) do channel loop for setting the active channel > e) if given rank is zero or inactive on the specific channel, > clear the timings for the associated channel > f) finally, return error if number of channels is zero > > Tested in NanoPI-NEO4 since it support single channel sdram > configuration. > > Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> > Signed-off-by: YouMin Chen <cym@rock-chips.com> > --- > drivers/ram/rockchip/sdram_rk3399.c | 110 ++++++++++++++++++++++------ > 1 file changed, 86 insertions(+), 24 deletions(-) > > diff --git a/drivers/ram/rockchip/sdram_rk3399.c b/drivers/ram/rockchip/sdram_rk3399.c > index 8bbacb5275..b83955f94e 100644 > --- a/drivers/ram/rockchip/sdram_rk3399.c > +++ b/drivers/ram/rockchip/sdram_rk3399.c > @@ -1254,13 +1254,52 @@ static unsigned char calculate_stride(struct rk3399_sdram_params *params) > return stride; > } > > +static void clear_channel_params(struct rk3399_sdram_params *params, u8 channel) > +{ > + params->ch[channel].cap_info.rank = 0; > + params->ch[channel].cap_info.col = 0; > + params->ch[channel].cap_info.bk = 0; > + params->ch[channel].cap_info.bw = 32; > + params->ch[channel].cap_info.dbw = 32; > + params->ch[channel].cap_info.row_3_4 = 0; > + params->ch[channel].cap_info.cs0_row = 0; > + params->ch[channel].cap_info.cs1_row = 0; > + params->ch[channel].cap_info.ddrconfig = 0; > +} > + > +static int pctl_init(struct dram_info *dram, struct rk3399_sdram_params *params) > +{ > + int channel; > + int ret; > + > + for (channel = 0; channel < 2; channel++) { > + const struct chan_info *chan = &dram->chan[channel]; > + struct rk3399_cru *cru = dram->cru; > + struct rk3399_ddr_publ_regs *publ = chan->publ; > + > + phy_pctrl_reset(cru, channel); > + phy_dll_bypass_set(publ, params->base.ddr_freq); > + > + ret = pctl_cfg(dram, chan, channel, params); > + if (ret < 0) { > + printf("%s: pctl config failed\n", __func__); > + return ret; > + } > + > + /* start to trigger initialization */ > + pctl_start(dram, channel); > + } > + > + return 0; > +} > + > static int sdram_init(struct dram_info *dram, > struct rk3399_sdram_params *params) > { > unsigned char dramtype = params->base.dramtype; > unsigned int ddr_freq = params->base.ddr_freq; > - struct rk3399_cru *cru = dram->cru; > - int channel; > + u32 training_flag = PI_READ_GATE_TRAINING; > + int channel, ch, rank; > int ret; > > debug("Starting SDRAM initialization...\n"); > @@ -1272,36 +1311,59 @@ static int sdram_init(struct dram_info *dram, > return -E2BIG; > } > > - for (channel = 0; channel < 2; channel++) { > - const struct chan_info *chan = &dram->chan[channel]; > - struct rk3399_ddr_publ_regs *publ = chan->publ; > + for (ch = 0; ch < 2; ch++) { > + params->ch[ch].cap_info.rank = 2; > + for (rank = 2; rank != 0; rank--) { > + ret = pctl_init(dram, params); > + if (ret < 0) { > + printf("%s: pctl init failed\n", __func__); > + return ret; > + } > > - phy_pctrl_reset(cru, channel); > - phy_dll_bypass_set(publ, ddr_freq); > + /* LPDDR2/LPDDR3 need to wait DAI complete, max 10us */ > + if (dramtype == LPDDR3) > + udelay(10); > > - if (channel >= params->base.num_channels) > - continue; > + params->ch[ch].cap_info.rank = rank; > > - ret = pctl_cfg(dram, chan, channel, params); > - if (ret < 0) { > - printf("%s: pctl config failed\n", __func__); > - return ret; > - } > + /* > + * LPDDR3 CA training msut be trigger before > + * other training. > + * DDR3 is not have CA training. > + */ > + if (params->base.dramtype == LPDDR3) > + training_flag |= PI_CA_TRAINING; > > - /* start to trigger initialization */ > - pctl_start(dram, channel); > + if (!(data_training(&dram->chan[ch], ch, > + params, training_flag))) > + break; > + } > + /* Computed rank with associated channel number */ > + params->ch[ch].cap_info.rank = rank; > + } > > - /* LPDDR2/LPDDR3 need to wait DAI complete, max 10us */ > - if (dramtype == LPDDR3) > - udelay(10); > + params->base.num_channels = 0; > + for (channel = 0; channel < 2; channel++) { > + const struct chan_info *chan = &dram->chan[channel]; > + struct sdram_cap_info *cap_info = ¶ms->ch[channel].cap_info; > > - if (data_training(chan, channel, params, PI_FULL_TRAINING)) { > - printf("%s: data training failed\n", __func__); > - return -EIO; > + if (cap_info->rank == 0) { > + clear_channel_params(params, channel); > + continue; > + } else { > + params->base.num_channels++; > } > > - set_ddrconfig(chan, params, channel, > - params->ch[channel].cap_info.ddrconfig); > + debug("Channel "); > + debug(channel ? "1: " : "0: "); > + > + set_ddrconfig(chan, params, channel, cap_info->ddrconfig); > + } > + > + if (params->base.num_channels == 0) { > + printf("%s: ", __func__); > + printf(" - %dMHz failed!\n", params->base.ddr_freq); > + return -EINVAL; > } > > params->base.stride = calculate_stride(params);
Hi Kever, On Wed, Jul 17, 2019 at 6:23 PM Kever Yang <kever.yang@rock-chips.com> wrote: > > Hi Jagan, > > I'm sure this patch have some problem with evb-rk3399, which I > think make the ddr not init correctly and error happen in ATF. Would you help to share the log for this. I made test on Nanopi-m4 which has same ddr type as evb, LPDDR3 and it booted fine with mainline ATF (with PLAT=rk3399 bl31). Below is the log details. U-Boot TPL 2019.07-00145-gcb5756d9e2-dirty (Jul 18 2019 - 14:55:23) Channel 0: LPDDR3, 933MHz BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=32 Size=2048MB Channel 1: LPDDR3, 933MHz BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=32 Size=2048MB 256B stride Trying to boot from BOOTROM Returning to boot ROM... U-Boot SPL 2019.07-00145-gcb5756d9e2-dirty (Jul 18 2019 - 14:55:23 +0530) Trying to boot from MMC1 U-Boot 2019.07-00145-gcb5756d9e2-dirty (Jul 18 2019 - 14:55:23 +0530) Model: FriendlyElec NanoPi M4 DRAM: 3.9 GiB MMC: dwmmc@fe310000: 2, dwmmc@fe320000: 1, sdhci@fe330000: 0 Loading Environment from MMC... *** Warning - bad CRC, using default environment In: serial@ff1a0000 Out: serial@ff1a0000 Err: serial@ff1a0000 Model: FriendlyElec NanoPi M4 Let me know if have anything to add? Jagan.
diff --git a/drivers/ram/rockchip/sdram_rk3399.c b/drivers/ram/rockchip/sdram_rk3399.c index 8bbacb5275..b83955f94e 100644 --- a/drivers/ram/rockchip/sdram_rk3399.c +++ b/drivers/ram/rockchip/sdram_rk3399.c @@ -1254,13 +1254,52 @@ static unsigned char calculate_stride(struct rk3399_sdram_params *params) return stride; } +static void clear_channel_params(struct rk3399_sdram_params *params, u8 channel) +{ + params->ch[channel].cap_info.rank = 0; + params->ch[channel].cap_info.col = 0; + params->ch[channel].cap_info.bk = 0; + params->ch[channel].cap_info.bw = 32; + params->ch[channel].cap_info.dbw = 32; + params->ch[channel].cap_info.row_3_4 = 0; + params->ch[channel].cap_info.cs0_row = 0; + params->ch[channel].cap_info.cs1_row = 0; + params->ch[channel].cap_info.ddrconfig = 0; +} + +static int pctl_init(struct dram_info *dram, struct rk3399_sdram_params *params) +{ + int channel; + int ret; + + for (channel = 0; channel < 2; channel++) { + const struct chan_info *chan = &dram->chan[channel]; + struct rk3399_cru *cru = dram->cru; + struct rk3399_ddr_publ_regs *publ = chan->publ; + + phy_pctrl_reset(cru, channel); + phy_dll_bypass_set(publ, params->base.ddr_freq); + + ret = pctl_cfg(dram, chan, channel, params); + if (ret < 0) { + printf("%s: pctl config failed\n", __func__); + return ret; + } + + /* start to trigger initialization */ + pctl_start(dram, channel); + } + + return 0; +} + static int sdram_init(struct dram_info *dram, struct rk3399_sdram_params *params) { unsigned char dramtype = params->base.dramtype; unsigned int ddr_freq = params->base.ddr_freq; - struct rk3399_cru *cru = dram->cru; - int channel; + u32 training_flag = PI_READ_GATE_TRAINING; + int channel, ch, rank; int ret; debug("Starting SDRAM initialization...\n"); @@ -1272,36 +1311,59 @@ static int sdram_init(struct dram_info *dram, return -E2BIG; } - for (channel = 0; channel < 2; channel++) { - const struct chan_info *chan = &dram->chan[channel]; - struct rk3399_ddr_publ_regs *publ = chan->publ; + for (ch = 0; ch < 2; ch++) { + params->ch[ch].cap_info.rank = 2; + for (rank = 2; rank != 0; rank--) { + ret = pctl_init(dram, params); + if (ret < 0) { + printf("%s: pctl init failed\n", __func__); + return ret; + } - phy_pctrl_reset(cru, channel); - phy_dll_bypass_set(publ, ddr_freq); + /* LPDDR2/LPDDR3 need to wait DAI complete, max 10us */ + if (dramtype == LPDDR3) + udelay(10); - if (channel >= params->base.num_channels) - continue; + params->ch[ch].cap_info.rank = rank; - ret = pctl_cfg(dram, chan, channel, params); - if (ret < 0) { - printf("%s: pctl config failed\n", __func__); - return ret; - } + /* + * LPDDR3 CA training msut be trigger before + * other training. + * DDR3 is not have CA training. + */ + if (params->base.dramtype == LPDDR3) + training_flag |= PI_CA_TRAINING; - /* start to trigger initialization */ - pctl_start(dram, channel); + if (!(data_training(&dram->chan[ch], ch, + params, training_flag))) + break; + } + /* Computed rank with associated channel number */ + params->ch[ch].cap_info.rank = rank; + } - /* LPDDR2/LPDDR3 need to wait DAI complete, max 10us */ - if (dramtype == LPDDR3) - udelay(10); + params->base.num_channels = 0; + for (channel = 0; channel < 2; channel++) { + const struct chan_info *chan = &dram->chan[channel]; + struct sdram_cap_info *cap_info = ¶ms->ch[channel].cap_info; - if (data_training(chan, channel, params, PI_FULL_TRAINING)) { - printf("%s: data training failed\n", __func__); - return -EIO; + if (cap_info->rank == 0) { + clear_channel_params(params, channel); + continue; + } else { + params->base.num_channels++; } - set_ddrconfig(chan, params, channel, - params->ch[channel].cap_info.ddrconfig); + debug("Channel "); + debug(channel ? "1: " : "0: "); + + set_ddrconfig(chan, params, channel, cap_info->ddrconfig); + } + + if (params->base.num_channels == 0) { + printf("%s: ", __func__); + printf(" - %dMHz failed!\n", params->base.ddr_freq); + return -EINVAL; } params->base.stride = calculate_stride(params);