mbox series

[0/3] Add IMX290 CMOS image sensor support

Message ID 20190703190230.12392-1-manivannan.sadhasivam@linaro.org (mailing list archive)
Headers show
Series Add IMX290 CMOS image sensor support | expand

Message

Manivannan Sadhasivam July 3, 2019, 7:02 p.m. UTC 
Hello,

This patchset adds support for IMX290 CMOS image sensor from Sony.
Sensor can be programmed through I2C and 4-wire interface but the
current driver only supports I2C interface. Also, the sensor is
capable of outputting frames in following 3 interfaces:

* CMOS logic parallel SDR output
* Low voltage LVDS serial DDR output
* CSI-2 serial data output

But the current driver only supports CSI-2 output available from 4 lanes.
In the case of sensor resolution, driver only supports 1920x1080 and
1280x720 at mid data rate of 445.5 Mpbs.

The driver has been validated using Framos IMX290 module interfaced to
96Boards Dragonboard410c.

Thanks,
Mani

Manivannan Sadhasivam (3):
  dt-bindings: media: i2c: Add IMX290 CMOS sensor binding
  media: i2c: Add IMX290 CMOS image sensor driver
  MAINTAINERS: Add entry for IMX290 CMOS image sensor driver

 .../devicetree/bindings/media/i2c/imx290.txt  |  51 ++
 MAINTAINERS                                   |   8 +
 drivers/media/i2c/Kconfig                     |  11 +
 drivers/media/i2c/Makefile                    |   1 +
 drivers/media/i2c/imx290.c                    | 845 ++++++++++++++++++
 5 files changed, 916 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/i2c/imx290.txt
 create mode 100644 drivers/media/i2c/imx290.c

Comments

Manivannan Sadhasivam July 30, 2019, 4:12 a.m. UTC | #1 
On Thu, Jul 04, 2019 at 12:32:27AM +0530, Manivannan Sadhasivam wrote:
> Hello,
> 
> This patchset adds support for IMX290 CMOS image sensor from Sony.
> Sensor can be programmed through I2C and 4-wire interface but the
> current driver only supports I2C interface. Also, the sensor is
> capable of outputting frames in following 3 interfaces:
> 
> * CMOS logic parallel SDR output
> * Low voltage LVDS serial DDR output
> * CSI-2 serial data output
> 
> But the current driver only supports CSI-2 output available from 4 lanes.
> In the case of sensor resolution, driver only supports 1920x1080 and
> 1280x720 at mid data rate of 445.5 Mpbs.
> 
> The driver has been validated using Framos IMX290 module interfaced to
> 96Boards Dragonboard410c.
> 

Ping on the patchset!

Thanks,
Mani

> Thanks,
> Mani
> 
> Manivannan Sadhasivam (3):
>   dt-bindings: media: i2c: Add IMX290 CMOS sensor binding
>   media: i2c: Add IMX290 CMOS image sensor driver
>   MAINTAINERS: Add entry for IMX290 CMOS image sensor driver
> 
>  .../devicetree/bindings/media/i2c/imx290.txt  |  51 ++
>  MAINTAINERS                                   |   8 +
>  drivers/media/i2c/Kconfig                     |  11 +
>  drivers/media/i2c/Makefile                    |   1 +
>  drivers/media/i2c/imx290.c                    | 845 ++++++++++++++++++
>  5 files changed, 916 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/i2c/imx290.txt
>  create mode 100644 drivers/media/i2c/imx290.c
> 
> -- 
> 2.17.1
>