diff mbox series

pinctrl: stmfx: update pinconf settings

Message ID 1564053416-32192-1-git-send-email-amelie.delaunay@st.com (mailing list archive)
State Mainlined
Commit a502b343ebd0eab38f3cb33fbb84011847cf5aac
Headers show
Series pinctrl: stmfx: update pinconf settings | expand

Commit Message

Amelie Delaunay July 25, 2019, 11:16 a.m. UTC 
From: Alexandre Torgue <alexandre.torgue@st.com>

According to the following tab (coming from STMFX datasheet), updates
have to done in stmfx_pinconf_set function:

-"type" has to be set when "bias" is configured as "pull-up or pull-down"
-PIN_CONFIG_DRIVE_PUSH_PULL should only be used when gpio is configured as
 output. There is so no need to check direction.

DIR | TYPE | PUPD | MFX GPIO configuration
----|------|------|---------------------------------------------------
1   | 1    | 1    | OUTPUT open drain with internal pull-up resistor
----|------|------|---------------------------------------------------
1   | 1    | 0    | OUTPUT open drain with internal pull-down resistor
----|------|------|---------------------------------------------------
1   | 0    | 0/1  | OUTPUT push pull no pull
----|------|------|---------------------------------------------------
0   | 1    | 1    | INPUT with internal pull-up resistor
----|------|------|---------------------------------------------------
0   | 1    | 0    | INPUT with internal pull-down resistor
----|------|------|---------------------------------------------------
0   | 0    | 1    | INPUT floating
----|------|------|---------------------------------------------------
0   | 0    | 0    | analog (GPIO not used, default setting)

Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
---
 drivers/pinctrl/pinctrl-stmfx.c | 24 ++++++++++++------------
 1 file changed, 12 insertions(+), 12 deletions(-)

Comments

Linus Walleij Aug. 5, 2019, 10:15 a.m. UTC | #1 
On Thu, Jul 25, 2019 at 1:16 PM Amelie Delaunay <amelie.delaunay@st.com> wrote:

> From: Alexandre Torgue <alexandre.torgue@st.com>
>
> According to the following tab (coming from STMFX datasheet), updates
> have to done in stmfx_pinconf_set function:
>
> -"type" has to be set when "bias" is configured as "pull-up or pull-down"
> -PIN_CONFIG_DRIVE_PUSH_PULL should only be used when gpio is configured as
>  output. There is so no need to check direction.
>
> DIR | TYPE | PUPD | MFX GPIO configuration
> ----|------|------|---------------------------------------------------
> 1   | 1    | 1    | OUTPUT open drain with internal pull-up resistor
> ----|------|------|---------------------------------------------------
> 1   | 1    | 0    | OUTPUT open drain with internal pull-down resistor
> ----|------|------|---------------------------------------------------
> 1   | 0    | 0/1  | OUTPUT push pull no pull
> ----|------|------|---------------------------------------------------
> 0   | 1    | 1    | INPUT with internal pull-up resistor
> ----|------|------|---------------------------------------------------
> 0   | 1    | 0    | INPUT with internal pull-down resistor
> ----|------|------|---------------------------------------------------
> 0   | 0    | 1    | INPUT floating
> ----|------|------|---------------------------------------------------
> 0   | 0    | 0    | analog (GPIO not used, default setting)
>
> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
> Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>

Patch applied.

Yours,
Linus Walleij
diff mbox series

Patch

diff --git a/drivers/pinctrl/pinctrl-stmfx.c b/drivers/pinctrl/pinctrl-stmfx.c
index d3332da..31b6e51 100644
--- a/drivers/pinctrl/pinctrl-stmfx.c
+++ b/drivers/pinctrl/pinctrl-stmfx.c
@@ -296,29 +296,29 @@  static int stmfx_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
 		switch (param) {
 		case PIN_CONFIG_BIAS_PULL_PIN_DEFAULT:
 		case PIN_CONFIG_BIAS_DISABLE:
+		case PIN_CONFIG_DRIVE_PUSH_PULL:
+			ret = stmfx_pinconf_set_type(pctl, pin, 0);
+			if (ret)
+				return ret;
+			break;
 		case PIN_CONFIG_BIAS_PULL_DOWN:
+			ret = stmfx_pinconf_set_type(pctl, pin, 1);
+			if (ret)
+				return ret;
 			ret = stmfx_pinconf_set_pupd(pctl, pin, 0);
 			if (ret)
 				return ret;
 			break;
 		case PIN_CONFIG_BIAS_PULL_UP:
-			ret = stmfx_pinconf_set_pupd(pctl, pin, 1);
+			ret = stmfx_pinconf_set_type(pctl, pin, 1);
 			if (ret)
 				return ret;
-			break;
-		case PIN_CONFIG_DRIVE_OPEN_DRAIN:
-			if (!dir)
-				ret = stmfx_pinconf_set_type(pctl, pin, 1);
-			else
-				ret = stmfx_pinconf_set_type(pctl, pin, 0);
+			ret = stmfx_pinconf_set_pupd(pctl, pin, 1);
 			if (ret)
 				return ret;
 			break;
-		case PIN_CONFIG_DRIVE_PUSH_PULL:
-			if (!dir)
-				ret = stmfx_pinconf_set_type(pctl, pin, 0);
-			else
-				ret = stmfx_pinconf_set_type(pctl, pin, 1);
+		case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+			ret = stmfx_pinconf_set_type(pctl, pin, 1);
 			if (ret)
 				return ret;
 			break;