| Message ID | 20190715081514.81129-3-sean@geanix.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [v2,1/6] iio: imu: st_lsm6dsx: move interrupt thread to core | expand |
> Add event channels that controls the creation of motion events. > > Signed-off-by: Sean Nyekjaer <sean@geanix.com> > --- > > Changes since v1: > * added handling of LSM6 > * added CHANNEL info with events for ACC > * removed st_lsm6dsx_set_event_threshold function > * added check of event type to event channels > > Issues: > * This currently breaks buffered reads, as the interrupt stays high. > This happens when MD1_CFG INT1_WU (wakeup event routes to INT1) is > enabled. > The datasheet doesn't seem to decribe whats happening and I can't > find a status register to read somehing useful. > Maybe it's impossible to share the buffered reads interrupt with > the wakeup interrupt? Could you explain this issue a bit more? adding st folks... > > drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h | 30 ++++ > drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c | 164 +++++++++++++++++-- > 2 files changed, 182 insertions(+), 12 deletions(-) > > diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h > index 738bed4a9752..fef08b7cf2a0 100644 > --- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h > +++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h > @@ -12,6 +12,7 @@ > #define ST_LSM6DSX_H > > #include <linux/device.h> > +#include <linux/iio/iio.h> > > #define ST_LSM6DS3_DEV_NAME "lsm6ds3" > #define ST_LSM6DS3H_DEV_NAME "lsm6ds3h" > @@ -50,6 +51,26 @@ enum st_lsm6dsx_hw_id { > * ST_LSM6DSX_TAGGED_SAMPLE_SIZE) > #define ST_LSM6DSX_SHIFT_VAL(val, mask) (((val) << __ffs(mask)) & (mask)) > > +#define ST_LSM6DSX_CHANNEL_ACC(chan_type, addr, mod, scan_idx) \ > +{ \ > + .type = chan_type, \ > + .address = addr, \ > + .modified = 1, \ > + .channel2 = mod, \ > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \ > + BIT(IIO_CHAN_INFO_SCALE), \ > + .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ), \ > + .scan_index = scan_idx, \ > + .scan_type = { \ > + .sign = 's', \ > + .realbits = 16, \ > + .storagebits = 16, \ > + .endianness = IIO_LE, \ > + }, \ > + .event_spec = &st_lsm6dsx_event, \ > + .num_event_specs = 1, \ > +} I would prefer to extend existing macros > + > #define ST_LSM6DSX_CHANNEL(chan_type, addr, mod, scan_idx) \ > { \ > .type = chan_type, \ > @@ -297,6 +318,8 @@ struct st_lsm6dsx_hw { > u8 enable_mask; > u8 ts_sip; > u8 sip; > + u8 event_threshold; > + bool enable_event; > int drdy_pin; > > u8 *buff; > @@ -306,6 +329,13 @@ struct st_lsm6dsx_hw { > const struct st_lsm6dsx_settings *settings; > }; > > +static const struct iio_event_spec st_lsm6dsx_event = { > + .type = IIO_EV_TYPE_THRESH, > + .dir = IIO_EV_DIR_EITHER, > + .mask_separate = BIT(IIO_EV_INFO_VALUE) | > + BIT(IIO_EV_INFO_ENABLE) > +}; > + > static const unsigned long st_lsm6dsx_available_scan_masks[] = {0x7, 0x0}; > extern const struct dev_pm_ops st_lsm6dsx_pm_ops; > > diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c > index 2c11addf568b..6decb0846f1a 100644 > --- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c > +++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c > @@ -76,6 +76,16 @@ > #define ST_LSM6DSX_REG_GYRO_OUT_Y_L_ADDR 0x24 > #define ST_LSM6DSX_REG_GYRO_OUT_Z_L_ADDR 0x26 > > +#define ST_LSM6DSX_REG_TAP_CFG_ADDR 0x58 > +#define ST_LSM6DSX_REG_TAP_CFG_INT_EN_MASK BIT(7) I am pretty sure this is not true at least for lsm6ds3/lsm6ds3h > + > +#define ST_LSM6DSX_REG_WAKE_UP_ADDR 0x5B > +#define ST_LSM6DSX_REG_WAKE_UP_THRES_MASK GENMASK(5, 0) > + > +#define ST_LSM6DSX_REG_MD1_CFG_ADDR 0x5E > +#define ST_LSM6DSX_REG_MD2_CFG_ADDR 0x5F > +#define ST_LSM6DSX_REG_MD_CFG_INT_WU_MASK BIT(5) > + > static const struct st_lsm6dsx_odr_table_entry st_lsm6dsx_odr_table[] = { > [ST_LSM6DSX_ID_ACC] = { > .reg = { > @@ -470,12 +480,12 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { > }; > > static const struct iio_chan_spec st_lsm6dsx_acc_channels[] = { > - ST_LSM6DSX_CHANNEL(IIO_ACCEL, ST_LSM6DSX_REG_ACC_OUT_X_L_ADDR, > - IIO_MOD_X, 0), > - ST_LSM6DSX_CHANNEL(IIO_ACCEL, ST_LSM6DSX_REG_ACC_OUT_Y_L_ADDR, > - IIO_MOD_Y, 1), > - ST_LSM6DSX_CHANNEL(IIO_ACCEL, ST_LSM6DSX_REG_ACC_OUT_Z_L_ADDR, > - IIO_MOD_Z, 2), > + ST_LSM6DSX_CHANNEL_ACC(IIO_ACCEL, ST_LSM6DSX_REG_ACC_OUT_X_L_ADDR, > + IIO_MOD_X, 0), > + ST_LSM6DSX_CHANNEL_ACC(IIO_ACCEL, ST_LSM6DSX_REG_ACC_OUT_Y_L_ADDR, > + IIO_MOD_Y, 1), > + ST_LSM6DSX_CHANNEL_ACC(IIO_ACCEL, ST_LSM6DSX_REG_ACC_OUT_Z_L_ADDR, > + IIO_MOD_Z, 2), > IIO_CHAN_SOFT_TIMESTAMP(3), > }; > > @@ -679,18 +689,21 @@ static int st_lsm6dsx_read_oneshot(struct st_lsm6dsx_sensor *sensor, > int err, delay; > __le16 data; > > - err = st_lsm6dsx_sensor_set_enable(sensor, true); > - if (err < 0) > - return err; > + if (!hw->enable_event) { > + err = st_lsm6dsx_sensor_set_enable(sensor, true); > + if (err < 0) > + return err; > > - delay = 1000000 / sensor->odr; > - usleep_range(delay, 2 * delay); > + delay = 1000000 / sensor->odr; > + usleep_range(delay, 2 * delay); > + } > > err = st_lsm6dsx_read_locked(hw, addr, &data, sizeof(data)); > if (err < 0) > return err; > > - st_lsm6dsx_sensor_set_enable(sensor, false); > + if (!hw->enable_event) > + st_lsm6dsx_sensor_set_enable(sensor, false); > > *val = (s16)le16_to_cpu(data); > > @@ -763,6 +776,94 @@ static int st_lsm6dsx_write_raw(struct iio_dev *iio_dev, > return err; > } > > +static int st_lsm6dsx_read_event(struct iio_dev *iio_dev, > + const struct iio_chan_spec *chan, > + enum iio_event_type type, > + enum iio_event_direction dir, > + enum iio_event_info info, > + int *val, int *val2) > +{ > + struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); > + struct st_lsm6dsx_hw *hw = sensor->hw; > + > + if (type != IIO_EV_TYPE_THRESH) > + return -EINVAL; > + > + *val2 = 0; > + *val = hw->event_threshold; > + > + return IIO_VAL_INT; > +} > + > +static int st_lsm6dsx_write_event(struct iio_dev *iio_dev, > + const struct iio_chan_spec *chan, > + enum iio_event_type type, > + enum iio_event_direction dir, > + enum iio_event_info info, > + int val, int val2) > +{ > + struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); > + struct st_lsm6dsx_hw *hw = sensor->hw; > + int err; > + > + if (type != IIO_EV_TYPE_THRESH) > + return -EINVAL; > + > + if (!hw->enable_event) > + return -EBUSY; I guess it is ok to configure the threshold first, no? > + > + if (val < 0 || val > 31) > + return -EINVAL; > + > + err = regmap_update_bits(hw->regmap, ST_LSM6DSX_REG_WAKE_UP_ADDR, > + ST_LSM6DSX_REG_WAKE_UP_THRES_MASK, > + val); > + if (err) > + return -EINVAL; > + > + hw->event_threshold = val; > + > + return 0; > +} > + > +static int st_lsm6dsx_read_event_config(struct iio_dev *iio_dev, > + const struct iio_chan_spec *chan, > + enum iio_event_type type, > + enum iio_event_direction dir) > +{ > + struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); > + struct st_lsm6dsx_hw *hw = sensor->hw; > + > + if (type != IIO_EV_TYPE_THRESH) > + return -EINVAL; > + > + return hw->enable_event; > +} > + > +static int st_lsm6dsx_write_event_config(struct iio_dev *iio_dev, > + const struct iio_chan_spec *chan, > + enum iio_event_type type, > + enum iio_event_direction dir, > + int state) > +{ > + struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); > + struct st_lsm6dsx_hw *hw = sensor->hw; > + > + if (type != IIO_EV_TYPE_THRESH) > + return -EINVAL; > + > + if (state && hw->enable_event) > + return 0; > + > + hw->enable_event = state; > + if (state) > + st_lsm6dsx_sensor_set_enable(sensor, true); > + else > + st_lsm6dsx_sensor_set_enable(sensor, false); st_lsm6dsx_sensor_set_enable can fails. Why not do err = st_lsm6dsx_sensor_set_enable(sensor, state); if (err < 0) return err; hw->enable_event = state;; return 0; > + > + return 0; > +} > + > int st_lsm6dsx_set_watermark(struct iio_dev *iio_dev, unsigned int val) > { > struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); > @@ -839,6 +940,10 @@ static const struct iio_info st_lsm6dsx_acc_info = { > .attrs = &st_lsm6dsx_acc_attribute_group, > .read_raw = st_lsm6dsx_read_raw, > .write_raw = st_lsm6dsx_write_raw, > + .read_event_value = st_lsm6dsx_read_event, > + .write_event_value = st_lsm6dsx_write_event, > + .read_event_config = st_lsm6dsx_read_event_config, > + .write_event_config = st_lsm6dsx_write_event_config, > .hwfifo_set_watermark = st_lsm6dsx_set_watermark, > }; > > @@ -1076,6 +1181,38 @@ static struct iio_dev *st_lsm6dsx_alloc_iiodev(struct st_lsm6dsx_hw *hw, > return iio_dev; > } > > +int st_lsm6dsx_event_setup(int id, struct st_lsm6dsx_hw *hw) > +{ > + int err; > + unsigned int md_reg; > + > + if (id == ST_ISM330DLC_ID) { > + /* Enable basic interrupts for ISM330 */ > + err = regmap_update_bits(hw->regmap, ST_LSM6DSX_REG_TAP_CFG_ADDR, > + ST_LSM6DSX_REG_TAP_CFG_INT_EN_MASK, > + ST_LSM6DSX_REG_TAP_CFG_INT_EN_MASK); please put device differences in st_lsm6dsx_sensor_settings[] > + if (err < 0) > + return err; > + } > + > + switch (hw->drdy_pin) { drdy_pin it is only used here right? If so we do not need it just enable this configuration by default. I would prefer to maintain the code simple > + case 1: > + md_reg = ST_LSM6DSX_REG_MD1_CFG_ADDR; > + break; > + case 2: > + md_reg = ST_LSM6DSX_REG_MD2_CFG_ADDR; > + break; > + default: > + return -EINVAL; > + } > + /* Enable wakeup interrupt */ > + err = regmap_update_bits(hw->regmap, md_reg, > + ST_LSM6DSX_REG_MD_CFG_INT_WU_MASK, > + ST_LSM6DSX_REG_MD_CFG_INT_WU_MASK); > + > + return err; > +} > + > static irqreturn_t st_lsm6dsx_handler_irq(int irq, void *private) > { > struct st_lsm6dsx_hw *hw = private; > @@ -1207,6 +1344,9 @@ int st_lsm6dsx_probe(struct device *dev, int irq, int hw_id, > err = st_lsm6dsx_fifo_setup(hw); > if (err < 0) > return err; newline here please > + err = st_lsm6dsx_event_setup(hw_id, hw); > + if (err < 0) > + return err; > } > > for (i = 0; i < ST_LSM6DSX_ID_MAX; i++) { > -- > 2.22.0 >
On Tue, 16 Jul 2019 10:29:27 +0200 Lorenzo Bianconi <lorenzo@kernel.org> wrote: > > Add event channels that controls the creation of motion events. > > > > Signed-off-by: Sean Nyekjaer <sean@geanix.com> > > --- > > > > Changes since v1: > > * added handling of LSM6 > > * added CHANNEL info with events for ACC > > * removed st_lsm6dsx_set_event_threshold function > > * added check of event type to event channels > > > > Issues: > > * This currently breaks buffered reads, as the interrupt stays high. > > This happens when MD1_CFG INT1_WU (wakeup event routes to INT1) is > > enabled. > > The datasheet doesn't seem to decribe whats happening and I can't > > find a status register to read somehing useful. > > Maybe it's impossible to share the buffered reads interrupt with > > the wakeup interrupt? > > Could you explain this issue a bit more? adding st folks... This isn't totally unheard of for other hardware. If it turns out to be a hardware restriction then the software approach is to return -EBUSY if anyone tries to enable an event whilst in buffered mode, and -EBUSY if anyone tries to enable buffered mode with an event enabled. It's rather ugly though definitely good to see if there is a proper solution! Thanks, Jonathan > > > > > drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h | 30 ++++ > > drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c | 164 +++++++++++++++++-- > > 2 files changed, 182 insertions(+), 12 deletions(-) > > > > diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h > > index 738bed4a9752..fef08b7cf2a0 100644 > > --- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h > > +++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h > > @@ -12,6 +12,7 @@ > > #define ST_LSM6DSX_H > > > > #include <linux/device.h> > > +#include <linux/iio/iio.h> > > > > #define ST_LSM6DS3_DEV_NAME "lsm6ds3" > > #define ST_LSM6DS3H_DEV_NAME "lsm6ds3h" > > @@ -50,6 +51,26 @@ enum st_lsm6dsx_hw_id { > > * ST_LSM6DSX_TAGGED_SAMPLE_SIZE) > > #define ST_LSM6DSX_SHIFT_VAL(val, mask) (((val) << __ffs(mask)) & (mask)) > > > > +#define ST_LSM6DSX_CHANNEL_ACC(chan_type, addr, mod, scan_idx) \ > > +{ \ > > + .type = chan_type, \ > > + .address = addr, \ > > + .modified = 1, \ > > + .channel2 = mod, \ > > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \ > > + BIT(IIO_CHAN_INFO_SCALE), \ > > + .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ), \ > > + .scan_index = scan_idx, \ > > + .scan_type = { \ > > + .sign = 's', \ > > + .realbits = 16, \ > > + .storagebits = 16, \ > > + .endianness = IIO_LE, \ > > + }, \ > > + .event_spec = &st_lsm6dsx_event, \ > > + .num_event_specs = 1, \ > > +} > > I would prefer to extend existing macros > > > + > > #define ST_LSM6DSX_CHANNEL(chan_type, addr, mod, scan_idx) \ > > { \ > > .type = chan_type, \ > > @@ -297,6 +318,8 @@ struct st_lsm6dsx_hw { > > u8 enable_mask; > > u8 ts_sip; > > u8 sip; > > + u8 event_threshold; > > + bool enable_event; > > int drdy_pin; > > > > u8 *buff; > > @@ -306,6 +329,13 @@ struct st_lsm6dsx_hw { > > const struct st_lsm6dsx_settings *settings; > > }; > > > > +static const struct iio_event_spec st_lsm6dsx_event = { > > + .type = IIO_EV_TYPE_THRESH, > > + .dir = IIO_EV_DIR_EITHER, > > + .mask_separate = BIT(IIO_EV_INFO_VALUE) | > > + BIT(IIO_EV_INFO_ENABLE) > > +}; > > + > > static const unsigned long st_lsm6dsx_available_scan_masks[] = {0x7, 0x0}; > > extern const struct dev_pm_ops st_lsm6dsx_pm_ops; > > > > diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c > > index 2c11addf568b..6decb0846f1a 100644 > > --- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c > > +++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c > > @@ -76,6 +76,16 @@ > > #define ST_LSM6DSX_REG_GYRO_OUT_Y_L_ADDR 0x24 > > #define ST_LSM6DSX_REG_GYRO_OUT_Z_L_ADDR 0x26 > > > > +#define ST_LSM6DSX_REG_TAP_CFG_ADDR 0x58 > > +#define ST_LSM6DSX_REG_TAP_CFG_INT_EN_MASK BIT(7) > > I am pretty sure this is not true at least for lsm6ds3/lsm6ds3h > > > + > > +#define ST_LSM6DSX_REG_WAKE_UP_ADDR 0x5B > > +#define ST_LSM6DSX_REG_WAKE_UP_THRES_MASK GENMASK(5, 0) > > + > > +#define ST_LSM6DSX_REG_MD1_CFG_ADDR 0x5E > > +#define ST_LSM6DSX_REG_MD2_CFG_ADDR 0x5F > > +#define ST_LSM6DSX_REG_MD_CFG_INT_WU_MASK BIT(5) > > + > > static const struct st_lsm6dsx_odr_table_entry st_lsm6dsx_odr_table[] = { > > [ST_LSM6DSX_ID_ACC] = { > > .reg = { > > @@ -470,12 +480,12 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { > > }; > > > > static const struct iio_chan_spec st_lsm6dsx_acc_channels[] = { > > - ST_LSM6DSX_CHANNEL(IIO_ACCEL, ST_LSM6DSX_REG_ACC_OUT_X_L_ADDR, > > - IIO_MOD_X, 0), > > - ST_LSM6DSX_CHANNEL(IIO_ACCEL, ST_LSM6DSX_REG_ACC_OUT_Y_L_ADDR, > > - IIO_MOD_Y, 1), > > - ST_LSM6DSX_CHANNEL(IIO_ACCEL, ST_LSM6DSX_REG_ACC_OUT_Z_L_ADDR, > > - IIO_MOD_Z, 2), > > + ST_LSM6DSX_CHANNEL_ACC(IIO_ACCEL, ST_LSM6DSX_REG_ACC_OUT_X_L_ADDR, > > + IIO_MOD_X, 0), > > + ST_LSM6DSX_CHANNEL_ACC(IIO_ACCEL, ST_LSM6DSX_REG_ACC_OUT_Y_L_ADDR, > > + IIO_MOD_Y, 1), > > + ST_LSM6DSX_CHANNEL_ACC(IIO_ACCEL, ST_LSM6DSX_REG_ACC_OUT_Z_L_ADDR, > > + IIO_MOD_Z, 2), > > IIO_CHAN_SOFT_TIMESTAMP(3), > > }; > > > > @@ -679,18 +689,21 @@ static int st_lsm6dsx_read_oneshot(struct st_lsm6dsx_sensor *sensor, > > int err, delay; > > __le16 data; > > > > - err = st_lsm6dsx_sensor_set_enable(sensor, true); > > - if (err < 0) > > - return err; > > + if (!hw->enable_event) { > > + err = st_lsm6dsx_sensor_set_enable(sensor, true); > > + if (err < 0) > > + return err; > > > > - delay = 1000000 / sensor->odr; > > - usleep_range(delay, 2 * delay); > > + delay = 1000000 / sensor->odr; > > + usleep_range(delay, 2 * delay); > > + } > > > > err = st_lsm6dsx_read_locked(hw, addr, &data, sizeof(data)); > > if (err < 0) > > return err; > > > > - st_lsm6dsx_sensor_set_enable(sensor, false); > > + if (!hw->enable_event) > > + st_lsm6dsx_sensor_set_enable(sensor, false); > > > > *val = (s16)le16_to_cpu(data); > > > > @@ -763,6 +776,94 @@ static int st_lsm6dsx_write_raw(struct iio_dev *iio_dev, > > return err; > > } > > > > +static int st_lsm6dsx_read_event(struct iio_dev *iio_dev, > > + const struct iio_chan_spec *chan, > > + enum iio_event_type type, > > + enum iio_event_direction dir, > > + enum iio_event_info info, > > + int *val, int *val2) > > +{ > > + struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); > > + struct st_lsm6dsx_hw *hw = sensor->hw; > > + > > + if (type != IIO_EV_TYPE_THRESH) > > + return -EINVAL; > > + > > + *val2 = 0; > > + *val = hw->event_threshold; > > + > > + return IIO_VAL_INT; > > +} > > + > > +static int st_lsm6dsx_write_event(struct iio_dev *iio_dev, > > + const struct iio_chan_spec *chan, > > + enum iio_event_type type, > > + enum iio_event_direction dir, > > + enum iio_event_info info, > > + int val, int val2) > > +{ > > + struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); > > + struct st_lsm6dsx_hw *hw = sensor->hw; > > + int err; > > + > > + if (type != IIO_EV_TYPE_THRESH) > > + return -EINVAL; > > + > > + if (!hw->enable_event) > > + return -EBUSY; > > I guess it is ok to configure the threshold first, no? > > > + > > + if (val < 0 || val > 31) > > + return -EINVAL; > > + > > + err = regmap_update_bits(hw->regmap, ST_LSM6DSX_REG_WAKE_UP_ADDR, > > + ST_LSM6DSX_REG_WAKE_UP_THRES_MASK, > > + val); > > + if (err) > > + return -EINVAL; > > + > > + hw->event_threshold = val; > > + > > + return 0; > > +} > > + > > +static int st_lsm6dsx_read_event_config(struct iio_dev *iio_dev, > > + const struct iio_chan_spec *chan, > > + enum iio_event_type type, > > + enum iio_event_direction dir) > > +{ > > + struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); > > + struct st_lsm6dsx_hw *hw = sensor->hw; > > + > > + if (type != IIO_EV_TYPE_THRESH) > > + return -EINVAL; > > + > > + return hw->enable_event; > > +} > > + > > +static int st_lsm6dsx_write_event_config(struct iio_dev *iio_dev, > > + const struct iio_chan_spec *chan, > > + enum iio_event_type type, > > + enum iio_event_direction dir, > > + int state) > > +{ > > + struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); > > + struct st_lsm6dsx_hw *hw = sensor->hw; > > + > > + if (type != IIO_EV_TYPE_THRESH) > > + return -EINVAL; > > + > > + if (state && hw->enable_event) > > + return 0; > > + > > + hw->enable_event = state; > > + if (state) > > + st_lsm6dsx_sensor_set_enable(sensor, true); > > + else > > + st_lsm6dsx_sensor_set_enable(sensor, false); > > st_lsm6dsx_sensor_set_enable can fails. Why not do > > err = st_lsm6dsx_sensor_set_enable(sensor, state); > if (err < 0) > return err; > > hw->enable_event = state;; > return 0; > > > + > > + return 0; > > +} > > + > > int st_lsm6dsx_set_watermark(struct iio_dev *iio_dev, unsigned int val) > > { > > struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); > > @@ -839,6 +940,10 @@ static const struct iio_info st_lsm6dsx_acc_info = { > > .attrs = &st_lsm6dsx_acc_attribute_group, > > .read_raw = st_lsm6dsx_read_raw, > > .write_raw = st_lsm6dsx_write_raw, > > + .read_event_value = st_lsm6dsx_read_event, > > + .write_event_value = st_lsm6dsx_write_event, > > + .read_event_config = st_lsm6dsx_read_event_config, > > + .write_event_config = st_lsm6dsx_write_event_config, > > .hwfifo_set_watermark = st_lsm6dsx_set_watermark, > > }; > > > > @@ -1076,6 +1181,38 @@ static struct iio_dev *st_lsm6dsx_alloc_iiodev(struct st_lsm6dsx_hw *hw, > > return iio_dev; > > } > > > > +int st_lsm6dsx_event_setup(int id, struct st_lsm6dsx_hw *hw) > > +{ > > + int err; > > + unsigned int md_reg; > > + > > + if (id == ST_ISM330DLC_ID) { > > + /* Enable basic interrupts for ISM330 */ > > + err = regmap_update_bits(hw->regmap, ST_LSM6DSX_REG_TAP_CFG_ADDR, > > + ST_LSM6DSX_REG_TAP_CFG_INT_EN_MASK, > > + ST_LSM6DSX_REG_TAP_CFG_INT_EN_MASK); > > please put device differences in st_lsm6dsx_sensor_settings[] > > > + if (err < 0) > > + return err; > > + } > > + > > + switch (hw->drdy_pin) { > > drdy_pin it is only used here right? If so we do not need it just enable this > configuration by default. I would prefer to maintain the code simple > > > + case 1: > > + md_reg = ST_LSM6DSX_REG_MD1_CFG_ADDR; > > + break; > > + case 2: > > + md_reg = ST_LSM6DSX_REG_MD2_CFG_ADDR; > > + break; > > + default: > > + return -EINVAL; > > + } > > + /* Enable wakeup interrupt */ > > + err = regmap_update_bits(hw->regmap, md_reg, > > + ST_LSM6DSX_REG_MD_CFG_INT_WU_MASK, > > + ST_LSM6DSX_REG_MD_CFG_INT_WU_MASK); > > + > > + return err; > > +} > > + > > static irqreturn_t st_lsm6dsx_handler_irq(int irq, void *private) > > { > > struct st_lsm6dsx_hw *hw = private; > > @@ -1207,6 +1344,9 @@ int st_lsm6dsx_probe(struct device *dev, int irq, int hw_id, > > err = st_lsm6dsx_fifo_setup(hw); > > if (err < 0) > > return err; > > newline here please > > > + err = st_lsm6dsx_event_setup(hw_id, hw); > > + if (err < 0) > > + return err; > > } > > > > for (i = 0; i < ST_LSM6DSX_ID_MAX; i++) { > > -- > > 2.22.0 > >
Back from vacation :-) On 16/07/2019 10.29, Lorenzo Bianconi wrote: >> Add event channels that controls the creation of motion events. >> >> Signed-off-by: Sean Nyekjaer <sean@geanix.com> >> --- >> >> Changes since v1: >> * added handling of LSM6 >> * added CHANNEL info with events for ACC >> * removed st_lsm6dsx_set_event_threshold function >> * added check of event type to event channels >> >> Issues: >> * This currently breaks buffered reads, as the interrupt stays high. >> This happens when MD1_CFG INT1_WU (wakeup event routes to INT1) is >> enabled. >> The datasheet doesn't seem to decribe whats happening and I can't >> find a status register to read somehing useful. >> Maybe it's impossible to share the buffered reads interrupt with >> the wakeup interrupt? > > Could you explain this issue a bit more? adding st folks... > I can try, there is not much to it... When buffered reads is enabled, and I enable wake-up at the same time, and then drop or shake the acc to create an event. The irq pin stays high, expected behavior would be it drops again when the buffer is read and the event is finished signaling. >> >> drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h | 30 ++++ >> drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c | 164 +++++++++++++++++-- >> 2 files changed, 182 insertions(+), 12 deletions(-) >> >> diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h >> index 738bed4a9752..fef08b7cf2a0 100644 >> --- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h >> +++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h >> @@ -12,6 +12,7 @@ >> #define ST_LSM6DSX_H >> >> #include <linux/device.h> >> +#include <linux/iio/iio.h> >> >> #define ST_LSM6DS3_DEV_NAME "lsm6ds3" >> #define ST_LSM6DS3H_DEV_NAME "lsm6ds3h" >> @@ -50,6 +51,26 @@ enum st_lsm6dsx_hw_id { >> * ST_LSM6DSX_TAGGED_SAMPLE_SIZE) >> #define ST_LSM6DSX_SHIFT_VAL(val, mask) (((val) << __ffs(mask)) & (mask)) >> >> +#define ST_LSM6DSX_CHANNEL_ACC(chan_type, addr, mod, scan_idx) \ >> +{ \ >> + .type = chan_type, \ >> + .address = addr, \ >> + .modified = 1, \ >> + .channel2 = mod, \ >> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \ >> + BIT(IIO_CHAN_INFO_SCALE), \ >> + .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ), \ >> + .scan_index = scan_idx, \ >> + .scan_type = { \ >> + .sign = 's', \ >> + .realbits = 16, \ >> + .storagebits = 16, \ >> + .endianness = IIO_LE, \ >> + }, \ >> + .event_spec = &st_lsm6dsx_event, \ >> + .num_event_specs = 1, \ >> +} > > I would prefer to extend existing macros > Please explain how... >> + >> #define ST_LSM6DSX_CHANNEL(chan_type, addr, mod, scan_idx) \ >> { \ >> .type = chan_type, \ >> @@ -297,6 +318,8 @@ struct st_lsm6dsx_hw { >> u8 enable_mask; >> u8 ts_sip; >> u8 sip; >> + u8 event_threshold; >> + bool enable_event; >> int drdy_pin; >> >> u8 *buff; >> @@ -306,6 +329,13 @@ struct st_lsm6dsx_hw { >> const struct st_lsm6dsx_settings *settings; >> }; >> >> +static const struct iio_event_spec st_lsm6dsx_event = { >> + .type = IIO_EV_TYPE_THRESH, >> + .dir = IIO_EV_DIR_EITHER, >> + .mask_separate = BIT(IIO_EV_INFO_VALUE) | >> + BIT(IIO_EV_INFO_ENABLE) >> +}; >> + >> static const unsigned long st_lsm6dsx_available_scan_masks[] = {0x7, 0x0}; >> extern const struct dev_pm_ops st_lsm6dsx_pm_ops; >> >> diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c >> index 2c11addf568b..6decb0846f1a 100644 >> --- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c >> +++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c >> @@ -76,6 +76,16 @@ >> #define ST_LSM6DSX_REG_GYRO_OUT_Y_L_ADDR 0x24 >> #define ST_LSM6DSX_REG_GYRO_OUT_Z_L_ADDR 0x26 >> >> +#define ST_LSM6DSX_REG_TAP_CFG_ADDR 0x58 >> +#define ST_LSM6DSX_REG_TAP_CFG_INT_EN_MASK BIT(7) > > I am pretty sure this is not true at least for lsm6ds3/lsm6ds3h > Will check >> + >> +#define ST_LSM6DSX_REG_WAKE_UP_ADDR 0x5B >> +#define ST_LSM6DSX_REG_WAKE_UP_THRES_MASK GENMASK(5, 0) >> + >> +#define ST_LSM6DSX_REG_MD1_CFG_ADDR 0x5E >> +#define ST_LSM6DSX_REG_MD2_CFG_ADDR 0x5F >> +#define ST_LSM6DSX_REG_MD_CFG_INT_WU_MASK BIT(5) >> + >> static const struct st_lsm6dsx_odr_table_entry st_lsm6dsx_odr_table[] = { >> [ST_LSM6DSX_ID_ACC] = { >> .reg = { >> @@ -470,12 +480,12 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { >> }; >> >> static const struct iio_chan_spec st_lsm6dsx_acc_channels[] = { >> - ST_LSM6DSX_CHANNEL(IIO_ACCEL, ST_LSM6DSX_REG_ACC_OUT_X_L_ADDR, >> - IIO_MOD_X, 0), >> - ST_LSM6DSX_CHANNEL(IIO_ACCEL, ST_LSM6DSX_REG_ACC_OUT_Y_L_ADDR, >> - IIO_MOD_Y, 1), >> - ST_LSM6DSX_CHANNEL(IIO_ACCEL, ST_LSM6DSX_REG_ACC_OUT_Z_L_ADDR, >> - IIO_MOD_Z, 2), >> + ST_LSM6DSX_CHANNEL_ACC(IIO_ACCEL, ST_LSM6DSX_REG_ACC_OUT_X_L_ADDR, >> + IIO_MOD_X, 0), >> + ST_LSM6DSX_CHANNEL_ACC(IIO_ACCEL, ST_LSM6DSX_REG_ACC_OUT_Y_L_ADDR, >> + IIO_MOD_Y, 1), >> + ST_LSM6DSX_CHANNEL_ACC(IIO_ACCEL, ST_LSM6DSX_REG_ACC_OUT_Z_L_ADDR, >> + IIO_MOD_Z, 2), >> IIO_CHAN_SOFT_TIMESTAMP(3), >> }; >> >> @@ -679,18 +689,21 @@ static int st_lsm6dsx_read_oneshot(struct st_lsm6dsx_sensor *sensor, >> int err, delay; >> __le16 data; >> >> - err = st_lsm6dsx_sensor_set_enable(sensor, true); >> - if (err < 0) >> - return err; >> + if (!hw->enable_event) { >> + err = st_lsm6dsx_sensor_set_enable(sensor, true); >> + if (err < 0) >> + return err; >> >> - delay = 1000000 / sensor->odr; >> - usleep_range(delay, 2 * delay); >> + delay = 1000000 / sensor->odr; >> + usleep_range(delay, 2 * delay); >> + } >> >> err = st_lsm6dsx_read_locked(hw, addr, &data, sizeof(data)); >> if (err < 0) >> return err; >> >> - st_lsm6dsx_sensor_set_enable(sensor, false); >> + if (!hw->enable_event) >> + st_lsm6dsx_sensor_set_enable(sensor, false); >> >> *val = (s16)le16_to_cpu(data); >> >> @@ -763,6 +776,94 @@ static int st_lsm6dsx_write_raw(struct iio_dev *iio_dev, >> return err; >> } >> >> +static int st_lsm6dsx_read_event(struct iio_dev *iio_dev, >> + const struct iio_chan_spec *chan, >> + enum iio_event_type type, >> + enum iio_event_direction dir, >> + enum iio_event_info info, >> + int *val, int *val2) >> +{ >> + struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); >> + struct st_lsm6dsx_hw *hw = sensor->hw; >> + >> + if (type != IIO_EV_TYPE_THRESH) >> + return -EINVAL; >> + >> + *val2 = 0; >> + *val = hw->event_threshold; >> + >> + return IIO_VAL_INT; >> +} >> + >> +static int st_lsm6dsx_write_event(struct iio_dev *iio_dev, >> + const struct iio_chan_spec *chan, >> + enum iio_event_type type, >> + enum iio_event_direction dir, >> + enum iio_event_info info, >> + int val, int val2) >> +{ >> + struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); >> + struct st_lsm6dsx_hw *hw = sensor->hw; >> + int err; >> + >> + if (type != IIO_EV_TYPE_THRESH) >> + return -EINVAL; >> + >> + if (!hw->enable_event) >> + return -EBUSY; > > I guess it is ok to configure the threshold first, no? > Will test and allow the threshold to be configured first. >> + >> + if (val < 0 || val > 31) >> + return -EINVAL; >> + >> + err = regmap_update_bits(hw->regmap, ST_LSM6DSX_REG_WAKE_UP_ADDR, >> + ST_LSM6DSX_REG_WAKE_UP_THRES_MASK, >> + val); >> + if (err) >> + return -EINVAL; >> + >> + hw->event_threshold = val; >> + >> + return 0; >> +} >> + >> +static int st_lsm6dsx_read_event_config(struct iio_dev *iio_dev, >> + const struct iio_chan_spec *chan, >> + enum iio_event_type type, >> + enum iio_event_direction dir) >> +{ >> + struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); >> + struct st_lsm6dsx_hw *hw = sensor->hw; >> + >> + if (type != IIO_EV_TYPE_THRESH) >> + return -EINVAL; >> + >> + return hw->enable_event; >> +} >> + >> +static int st_lsm6dsx_write_event_config(struct iio_dev *iio_dev, >> + const struct iio_chan_spec *chan, >> + enum iio_event_type type, >> + enum iio_event_direction dir, >> + int state) >> +{ >> + struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); >> + struct st_lsm6dsx_hw *hw = sensor->hw; >> + >> + if (type != IIO_EV_TYPE_THRESH) >> + return -EINVAL; >> + >> + if (state && hw->enable_event) >> + return 0; >> + >> + hw->enable_event = state; >> + if (state) >> + st_lsm6dsx_sensor_set_enable(sensor, true); >> + else >> + st_lsm6dsx_sensor_set_enable(sensor, false); > > st_lsm6dsx_sensor_set_enable can fails. Why not do > > err = st_lsm6dsx_sensor_set_enable(sensor, state); > if (err < 0) > return err; > > hw->enable_event = state;; > return 0; > Will change to this approach :-) >> + >> + return 0; >> +} >> + >> int st_lsm6dsx_set_watermark(struct iio_dev *iio_dev, unsigned int val) >> { >> struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); >> @@ -839,6 +940,10 @@ static const struct iio_info st_lsm6dsx_acc_info = { >> .attrs = &st_lsm6dsx_acc_attribute_group, >> .read_raw = st_lsm6dsx_read_raw, >> .write_raw = st_lsm6dsx_write_raw, >> + .read_event_value = st_lsm6dsx_read_event, >> + .write_event_value = st_lsm6dsx_write_event, >> + .read_event_config = st_lsm6dsx_read_event_config, >> + .write_event_config = st_lsm6dsx_write_event_config, >> .hwfifo_set_watermark = st_lsm6dsx_set_watermark, >> }; >> >> @@ -1076,6 +1181,38 @@ static struct iio_dev *st_lsm6dsx_alloc_iiodev(struct st_lsm6dsx_hw *hw, >> return iio_dev; >> } >> >> +int st_lsm6dsx_event_setup(int id, struct st_lsm6dsx_hw *hw) >> +{ >> + int err; >> + unsigned int md_reg; >> + >> + if (id == ST_ISM330DLC_ID) { >> + /* Enable basic interrupts for ISM330 */ >> + err = regmap_update_bits(hw->regmap, ST_LSM6DSX_REG_TAP_CFG_ADDR, >> + ST_LSM6DSX_REG_TAP_CFG_INT_EN_MASK, >> + ST_LSM6DSX_REG_TAP_CFG_INT_EN_MASK); > > please put device differences in st_lsm6dsx_sensor_settings[] > Will do. >> + if (err < 0) >> + return err; >> + } >> + >> + switch (hw->drdy_pin) { > > drdy_pin it is only used here right? If so we do not need it just enable this > configuration by default. I would prefer to maintain the code simple > >> + case 1: >> + md_reg = ST_LSM6DSX_REG_MD1_CFG_ADDR; >> + break; >> + case 2: >> + md_reg = ST_LSM6DSX_REG_MD2_CFG_ADDR; >> + break; >> + default: >> + return -EINVAL; >> + } >> + /* Enable wakeup interrupt */ >> + err = regmap_update_bits(hw->regmap, md_reg, >> + ST_LSM6DSX_REG_MD_CFG_INT_WU_MASK, >> + ST_LSM6DSX_REG_MD_CFG_INT_WU_MASK); >> + >> + return err; >> +} >> + >> static irqreturn_t st_lsm6dsx_handler_irq(int irq, void *private) >> { >> struct st_lsm6dsx_hw *hw = private; >> @@ -1207,6 +1344,9 @@ int st_lsm6dsx_probe(struct device *dev, int irq, int hw_id, >> err = st_lsm6dsx_fifo_setup(hw); >> if (err < 0) >> return err; > > newline here please > >> + err = st_lsm6dsx_event_setup(hw_id, hw); >> + if (err < 0) >> + return err; >> } >> >> for (i = 0; i < ST_LSM6DSX_ID_MAX; i++) { >> -- >> 2.22.0 >>
On 16/07/2019 10.29, Lorenzo Bianconi wrote: >> +#define ST_LSM6DSX_CHANNEL_ACC(chan_type, addr, mod, scan_idx) \ >> +{ \ >> + .type = chan_type, \ >> + .address = addr, \ >> + .modified = 1, \ >> + .channel2 = mod, \ >> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \ >> + BIT(IIO_CHAN_INFO_SCALE), \ >> + .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ), \ >> + .scan_index = scan_idx, \ >> + .scan_type = { \ >> + .sign = 's', \ >> + .realbits = 16, \ >> + .storagebits = 16, \ >> + .endianness = IIO_LE, \ >> + }, \ >> + .event_spec = &st_lsm6dsx_event, \ >> + .num_event_specs = 1, \ >> +} > > I would prefer to extend existing macros > >> + >> #define ST_LSM6DSX_CHANNEL(chan_type, addr, mod, scan_idx) \ >> { \ >> .type = chan_type, \ >> @@ -297,6 +318,8 @@ struct st_lsm6dsx_hw { >> u8 enable_mask; >> u8 ts_sip; >> u8 sip; >> + u8 event_threshold; >> + bool enable_event; >> int drdy_pin; >> >> u8 *buff; >> @@ -306,6 +329,13 @@ struct st_lsm6dsx_hw { >> const struct st_lsm6dsx_settings *settings; >> }; >> How would I do that when we have the `event_spec` for the accelerometer? /Sean
diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h index 738bed4a9752..fef08b7cf2a0 100644 --- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h +++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h @@ -12,6 +12,7 @@ #define ST_LSM6DSX_H #include <linux/device.h> +#include <linux/iio/iio.h> #define ST_LSM6DS3_DEV_NAME "lsm6ds3" #define ST_LSM6DS3H_DEV_NAME "lsm6ds3h" @@ -50,6 +51,26 @@ enum st_lsm6dsx_hw_id { * ST_LSM6DSX_TAGGED_SAMPLE_SIZE) #define ST_LSM6DSX_SHIFT_VAL(val, mask) (((val) << __ffs(mask)) & (mask)) +#define ST_LSM6DSX_CHANNEL_ACC(chan_type, addr, mod, scan_idx) \ +{ \ + .type = chan_type, \ + .address = addr, \ + .modified = 1, \ + .channel2 = mod, \ + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \ + BIT(IIO_CHAN_INFO_SCALE), \ + .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ), \ + .scan_index = scan_idx, \ + .scan_type = { \ + .sign = 's', \ + .realbits = 16, \ + .storagebits = 16, \ + .endianness = IIO_LE, \ + }, \ + .event_spec = &st_lsm6dsx_event, \ + .num_event_specs = 1, \ +} + #define ST_LSM6DSX_CHANNEL(chan_type, addr, mod, scan_idx) \ { \ .type = chan_type, \ @@ -297,6 +318,8 @@ struct st_lsm6dsx_hw { u8 enable_mask; u8 ts_sip; u8 sip; + u8 event_threshold; + bool enable_event; int drdy_pin; u8 *buff; @@ -306,6 +329,13 @@ struct st_lsm6dsx_hw { const struct st_lsm6dsx_settings *settings; }; +static const struct iio_event_spec st_lsm6dsx_event = { + .type = IIO_EV_TYPE_THRESH, + .dir = IIO_EV_DIR_EITHER, + .mask_separate = BIT(IIO_EV_INFO_VALUE) | + BIT(IIO_EV_INFO_ENABLE) +}; + static const unsigned long st_lsm6dsx_available_scan_masks[] = {0x7, 0x0}; extern const struct dev_pm_ops st_lsm6dsx_pm_ops; diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c index 2c11addf568b..6decb0846f1a 100644 --- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c +++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c @@ -76,6 +76,16 @@ #define ST_LSM6DSX_REG_GYRO_OUT_Y_L_ADDR 0x24 #define ST_LSM6DSX_REG_GYRO_OUT_Z_L_ADDR 0x26 +#define ST_LSM6DSX_REG_TAP_CFG_ADDR 0x58 +#define ST_LSM6DSX_REG_TAP_CFG_INT_EN_MASK BIT(7) + +#define ST_LSM6DSX_REG_WAKE_UP_ADDR 0x5B +#define ST_LSM6DSX_REG_WAKE_UP_THRES_MASK GENMASK(5, 0) + +#define ST_LSM6DSX_REG_MD1_CFG_ADDR 0x5E +#define ST_LSM6DSX_REG_MD2_CFG_ADDR 0x5F +#define ST_LSM6DSX_REG_MD_CFG_INT_WU_MASK BIT(5) + static const struct st_lsm6dsx_odr_table_entry st_lsm6dsx_odr_table[] = { [ST_LSM6DSX_ID_ACC] = { .reg = { @@ -470,12 +480,12 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { }; static const struct iio_chan_spec st_lsm6dsx_acc_channels[] = { - ST_LSM6DSX_CHANNEL(IIO_ACCEL, ST_LSM6DSX_REG_ACC_OUT_X_L_ADDR, - IIO_MOD_X, 0), - ST_LSM6DSX_CHANNEL(IIO_ACCEL, ST_LSM6DSX_REG_ACC_OUT_Y_L_ADDR, - IIO_MOD_Y, 1), - ST_LSM6DSX_CHANNEL(IIO_ACCEL, ST_LSM6DSX_REG_ACC_OUT_Z_L_ADDR, - IIO_MOD_Z, 2), + ST_LSM6DSX_CHANNEL_ACC(IIO_ACCEL, ST_LSM6DSX_REG_ACC_OUT_X_L_ADDR, + IIO_MOD_X, 0), + ST_LSM6DSX_CHANNEL_ACC(IIO_ACCEL, ST_LSM6DSX_REG_ACC_OUT_Y_L_ADDR, + IIO_MOD_Y, 1), + ST_LSM6DSX_CHANNEL_ACC(IIO_ACCEL, ST_LSM6DSX_REG_ACC_OUT_Z_L_ADDR, + IIO_MOD_Z, 2), IIO_CHAN_SOFT_TIMESTAMP(3), }; @@ -679,18 +689,21 @@ static int st_lsm6dsx_read_oneshot(struct st_lsm6dsx_sensor *sensor, int err, delay; __le16 data; - err = st_lsm6dsx_sensor_set_enable(sensor, true); - if (err < 0) - return err; + if (!hw->enable_event) { + err = st_lsm6dsx_sensor_set_enable(sensor, true); + if (err < 0) + return err; - delay = 1000000 / sensor->odr; - usleep_range(delay, 2 * delay); + delay = 1000000 / sensor->odr; + usleep_range(delay, 2 * delay); + } err = st_lsm6dsx_read_locked(hw, addr, &data, sizeof(data)); if (err < 0) return err; - st_lsm6dsx_sensor_set_enable(sensor, false); + if (!hw->enable_event) + st_lsm6dsx_sensor_set_enable(sensor, false); *val = (s16)le16_to_cpu(data); @@ -763,6 +776,94 @@ static int st_lsm6dsx_write_raw(struct iio_dev *iio_dev, return err; } +static int st_lsm6dsx_read_event(struct iio_dev *iio_dev, + const struct iio_chan_spec *chan, + enum iio_event_type type, + enum iio_event_direction dir, + enum iio_event_info info, + int *val, int *val2) +{ + struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); + struct st_lsm6dsx_hw *hw = sensor->hw; + + if (type != IIO_EV_TYPE_THRESH) + return -EINVAL; + + *val2 = 0; + *val = hw->event_threshold; + + return IIO_VAL_INT; +} + +static int st_lsm6dsx_write_event(struct iio_dev *iio_dev, + const struct iio_chan_spec *chan, + enum iio_event_type type, + enum iio_event_direction dir, + enum iio_event_info info, + int val, int val2) +{ + struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); + struct st_lsm6dsx_hw *hw = sensor->hw; + int err; + + if (type != IIO_EV_TYPE_THRESH) + return -EINVAL; + + if (!hw->enable_event) + return -EBUSY; + + if (val < 0 || val > 31) + return -EINVAL; + + err = regmap_update_bits(hw->regmap, ST_LSM6DSX_REG_WAKE_UP_ADDR, + ST_LSM6DSX_REG_WAKE_UP_THRES_MASK, + val); + if (err) + return -EINVAL; + + hw->event_threshold = val; + + return 0; +} + +static int st_lsm6dsx_read_event_config(struct iio_dev *iio_dev, + const struct iio_chan_spec *chan, + enum iio_event_type type, + enum iio_event_direction dir) +{ + struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); + struct st_lsm6dsx_hw *hw = sensor->hw; + + if (type != IIO_EV_TYPE_THRESH) + return -EINVAL; + + return hw->enable_event; +} + +static int st_lsm6dsx_write_event_config(struct iio_dev *iio_dev, + const struct iio_chan_spec *chan, + enum iio_event_type type, + enum iio_event_direction dir, + int state) +{ + struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); + struct st_lsm6dsx_hw *hw = sensor->hw; + + if (type != IIO_EV_TYPE_THRESH) + return -EINVAL; + + if (state && hw->enable_event) + return 0; + + hw->enable_event = state; + if (state) + st_lsm6dsx_sensor_set_enable(sensor, true); + else + st_lsm6dsx_sensor_set_enable(sensor, false); + + return 0; +} + int st_lsm6dsx_set_watermark(struct iio_dev *iio_dev, unsigned int val) { struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); @@ -839,6 +940,10 @@ static const struct iio_info st_lsm6dsx_acc_info = { .attrs = &st_lsm6dsx_acc_attribute_group, .read_raw = st_lsm6dsx_read_raw, .write_raw = st_lsm6dsx_write_raw, + .read_event_value = st_lsm6dsx_read_event, + .write_event_value = st_lsm6dsx_write_event, + .read_event_config = st_lsm6dsx_read_event_config, + .write_event_config = st_lsm6dsx_write_event_config, .hwfifo_set_watermark = st_lsm6dsx_set_watermark, }; @@ -1076,6 +1181,38 @@ static struct iio_dev *st_lsm6dsx_alloc_iiodev(struct st_lsm6dsx_hw *hw, return iio_dev; } +int st_lsm6dsx_event_setup(int id, struct st_lsm6dsx_hw *hw) +{ + int err; + unsigned int md_reg; + + if (id == ST_ISM330DLC_ID) { + /* Enable basic interrupts for ISM330 */ + err = regmap_update_bits(hw->regmap, ST_LSM6DSX_REG_TAP_CFG_ADDR, + ST_LSM6DSX_REG_TAP_CFG_INT_EN_MASK, + ST_LSM6DSX_REG_TAP_CFG_INT_EN_MASK); + if (err < 0) + return err; + } + + switch (hw->drdy_pin) { + case 1: + md_reg = ST_LSM6DSX_REG_MD1_CFG_ADDR; + break; + case 2: + md_reg = ST_LSM6DSX_REG_MD2_CFG_ADDR; + break; + default: + return -EINVAL; + } + /* Enable wakeup interrupt */ + err = regmap_update_bits(hw->regmap, md_reg, + ST_LSM6DSX_REG_MD_CFG_INT_WU_MASK, + ST_LSM6DSX_REG_MD_CFG_INT_WU_MASK); + + return err; +} + static irqreturn_t st_lsm6dsx_handler_irq(int irq, void *private) { struct st_lsm6dsx_hw *hw = private; @@ -1207,6 +1344,9 @@ int st_lsm6dsx_probe(struct device *dev, int irq, int hw_id, err = st_lsm6dsx_fifo_setup(hw); if (err < 0) return err; + err = st_lsm6dsx_event_setup(hw_id, hw); + if (err < 0) + return err; } for (i = 0; i < ST_LSM6DSX_ID_MAX; i++) {
Add event channels that controls the creation of motion events. Signed-off-by: Sean Nyekjaer <sean@geanix.com> --- Changes since v1: * added handling of LSM6 * added CHANNEL info with events for ACC * removed st_lsm6dsx_set_event_threshold function * added check of event type to event channels Issues: * This currently breaks buffered reads, as the interrupt stays high. This happens when MD1_CFG INT1_WU (wakeup event routes to INT1) is enabled. The datasheet doesn't seem to decribe whats happening and I can't find a status register to read somehing useful. Maybe it's impossible to share the buffered reads interrupt with the wakeup interrupt? drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h | 30 ++++ drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c | 164 +++++++++++++++++-- 2 files changed, 182 insertions(+), 12 deletions(-)