diff mbox series

[1/1] arm64: dts: qcom: Add Lenovo Yoga C630

Message ID 20190902132400.14084-1-lee.jones@linaro.org (mailing list archive)
State New, archived
Headers show
Series [1/1] arm64: dts: qcom: Add Lenovo Yoga C630 | expand

Commit Message

Lee Jones Sept. 2, 2019, 1:24 p.m. UTC
From: Bjorn Andersson <bjorn.andersson@linaro.org>

The Lenovo Yoga C630 is built on the SDM850 from Qualcomm, but this seem
to be similar enough to the SDM845 that we can reuse the sdm845.dtsi.

Supported by this patch is: keyboard, battery monitoring, UFS storage,
USB host and Bluetooth.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
 arch/arm64/boot/dts/qcom/Makefile             |   1 +
 .../boot/dts/qcom/sdm850-lenovo-yoga-c630.dts | 450 ++++++++++++++++++
 2 files changed, 451 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts

Comments

Bjorn Andersson Sept. 3, 2019, 5:44 a.m. UTC | #1
On Mon 02 Sep 06:24 PDT 2019, Lee Jones wrote:

> From: Bjorn Andersson <bjorn.andersson@linaro.org>
> 
> The Lenovo Yoga C630 is built on the SDM850 from Qualcomm, but this seem
> to be similar enough to the SDM845 that we can reuse the sdm845.dtsi.
> 
> Supported by this patch is: keyboard, battery monitoring, UFS storage,
> USB host and Bluetooth.

Applied this to next-20190829 and booted it, got a little bit of EFI FB,
then the screen goes blank and after a while I'm back in GRUB.

I've not been able to figure out what's causing this though.

Regards,
Bjorn

> 
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> Signed-off-by: Lee Jones <lee.jones@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/Makefile             |   1 +
>  .../boot/dts/qcom/sdm850-lenovo-yoga-c630.dts | 450 ++++++++++++++++++
>  2 files changed, 451 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts
> 
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 0a7e5dfce6f7..670c6c65f9e9 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -12,5 +12,6 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r2.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r3.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-db845c.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-mtp.dtb
> +dtb-$(CONFIG_ARCH_QCOM)	+= sdm850-lenovo-yoga-c630.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-1000.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-4000.dtb
> diff --git a/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts b/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts
> new file mode 100644
> index 000000000000..3177b054035f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts
> @@ -0,0 +1,450 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Lenovo Yoga C630
> + *
> + * Copyright (c) 2019, Linaro Ltd.
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> +#include "sdm845.dtsi"
> +#include "pm8998.dtsi"
> +
> +/ {
> +	model = "Lenovo Yoga C630";
> +	compatible = "lenovo,yoga-c630", "qcom,sdm845";
> +
> +	aliases {
> +		hsuart0 = &uart6;
> +	};
> +};
> +
> +&apps_rsc {
> +	pm8998-rpmh-regulators {
> +		compatible = "qcom,pm8998-rpmh-regulators";
> +		qcom,pmic-id = "a";
> +
> +		vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>;
> +		vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>;
> +
> +		vreg_s2a_1p125: smps2 {
> +		};
> +
> +		vreg_s3a_1p35: smps3 {
> +			regulator-min-microvolt = <1352000>;
> +			regulator-max-microvolt = <1352000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_s4a_1p8: smps4 {
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_s5a_2p04: smps5 {
> +			regulator-min-microvolt = <2040000>;
> +			regulator-max-microvolt = <2040000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_s7a_1p025: smps7 {
> +		};
> +
> +		vdd_qusb_hs0:
> +		vdda_hp_pcie_core:
> +		vdda_mipi_csi0_0p9:
> +		vdda_mipi_csi1_0p9:
> +		vdda_mipi_csi2_0p9:
> +		vdda_mipi_dsi0_pll:
> +		vdda_mipi_dsi1_pll:
> +		vdda_qlink_lv:
> +		vdda_qlink_lv_ck:
> +		vdda_qrefs_0p875:
> +		vdda_pcie_core:
> +		vdda_pll_cc_ebi01:
> +		vdda_pll_cc_ebi23:
> +		vdda_sp_sensor:
> +		vdda_ufs1_core:
> +		vdda_ufs2_core:
> +		vdda_usb1_ss_core:
> +		vdda_usb2_ss_core:
> +		vreg_l1a_0p875: ldo1 {
> +			regulator-min-microvolt = <880000>;
> +			regulator-max-microvolt = <880000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vddpx_10:
> +		vreg_l2a_1p2: ldo2 {
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1200000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-always-on;
> +		};
> +
> +		vreg_l3a_1p0: ldo3 {
> +		};
> +
> +		vdd_wcss_cx:
> +		vdd_wcss_mx:
> +		vdda_wcss_pll:
> +		vreg_l5a_0p8: ldo5 {
> +			regulator-min-microvolt = <800000>;
> +			regulator-max-microvolt = <800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vddpx_13:
> +		vreg_l6a_1p8: ldo6 {
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l7a_1p8: ldo7 {
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l8a_1p2: ldo8 {
> +		};
> +
> +		vreg_l9a_1p8: ldo9 {
> +		};
> +
> +		vreg_l10a_1p8: ldo10 {
> +		};
> +
> +		vreg_l11a_1p0: ldo11 {
> +		};
> +
> +		vdd_qfprom:
> +		vdd_qfprom_sp:
> +		vdda_apc1_cs_1p8:
> +		vdda_gfx_cs_1p8:
> +		vdda_qrefs_1p8:
> +		vdda_qusb_hs0_1p8:
> +		vddpx_11:
> +		vreg_l12a_1p8: ldo12 {
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vddpx_2:
> +		vreg_l13a_2p95: ldo13 {
> +		};
> +
> +		vreg_l14a_1p88: ldo14 {
> +			regulator-min-microvolt = <1880000>;
> +			regulator-max-microvolt = <1880000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l15a_1p8: ldo15 {
> +		};
> +
> +		vreg_l16a_2p7: ldo16 {
> +		};
> +
> +		vreg_l17a_1p3: ldo17 {
> +			regulator-min-microvolt = <1304000>;
> +			regulator-max-microvolt = <1304000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l18a_2p7: ldo18 {
> +		};
> +
> +		vreg_l19a_3p0: ldo19 {
> +			regulator-min-microvolt = <3100000>;
> +			regulator-max-microvolt = <3108000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l20a_2p95: ldo20 {
> +			regulator-min-microvolt = <2960000>;
> +			regulator-max-microvolt = <2960000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l21a_2p95: ldo21 {
> +		};
> +
> +		vreg_l22a_2p85: ldo22 {
> +		};
> +
> +		vreg_l23a_3p3: ldo23 {
> +		};
> +
> +		vdda_qusb_hs0_3p1:
> +		vreg_l24a_3p075: ldo24 {
> +			regulator-min-microvolt = <3075000>;
> +			regulator-max-microvolt = <3083000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l25a_3p3: ldo25 {
> +			regulator-min-microvolt = <3104000>;
> +			regulator-max-microvolt = <3112000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vdda_hp_pcie_1p2:
> +		vdda_hv_ebi0:
> +		vdda_hv_ebi1:
> +		vdda_hv_ebi2:
> +		vdda_hv_ebi3:
> +		vdda_mipi_csi_1p25:
> +		vdda_mipi_dsi0_1p2:
> +		vdda_mipi_dsi1_1p2:
> +		vdda_pcie_1p2:
> +		vdda_ufs1_1p2:
> +		vdda_ufs2_1p2:
> +		vdda_usb1_ss_1p2:
> +		vdda_usb2_ss_1p2:
> +		vreg_l26a_1p2: ldo26 {
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1208000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l28a_3p0: ldo28 {
> +		};
> +
> +		vreg_lvs1a_1p8: lvs1 {
> +		};
> +
> +		vreg_lvs2a_1p8: lvs2 {
> +		};
> +	};
> +};
> +
> +&apps_smmu {
> +	/* TODO: Figure out how to survive booting with this enabled */
> +	status = "disabled";
> +};
> +
> +&gcc {
> +	protected-clocks = <GCC_QSPI_CORE_CLK>,
> +			   <GCC_QSPI_CORE_CLK_SRC>,
> +			   <GCC_QSPI_CNOC_PERIPH_AHB_CLK>;
> +};
> +
> +&i2c1 {
> +	status = "okay";
> +	clock-frequency = <400000>;
> +
> +	battery@70 {
> +		compatible = "some,battery";
> +		reg = <0x70>;
> +	};
> +};
> +
> +&i2c3 {
> +	status = "okay";
> +	clock-frequency = <400000>;
> +
> +	hid@15 {
> +		compatible = "hid-over-i2c";
> +		reg = <0x15>;
> +		hid-descr-addr = <0x1>;
> +
> +		interrupts-extended = <&tlmm 37 IRQ_TYPE_EDGE_RISING>;
> +	};
> +
> +	hid@2c {
> +		compatible = "hid-over-i2c";
> +		reg = <0x2c>;
> +		hid-descr-addr = <0x20>;
> +
> +		interrupts-extended = <&tlmm 37 IRQ_TYPE_EDGE_RISING>;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&i2c2_hid_active>;
> +	};
> +};
> +
> +&i2c5 {
> +	status = "okay";
> +	clock-frequency = <400000>;
> +
> +	hid@10 {
> +		compatible = "hid-over-i2c";
> +		reg = <0x10>;
> +		hid-descr-addr = <0x1>;
> +
> +		interrupts-extended = <&tlmm 125 IRQ_TYPE_EDGE_FALLING>;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&i2c6_hid_active>;
> +	};
> +};
> +
> +&i2c11 {
> +	status = "okay";
> +	clock-frequency = <400000>;
> +
> +	hid@5c {
> +		compatible = "hid-over-i2c";
> +		reg = <0x5c>;
> +		hid-descr-addr = <0x1>;
> +
> +		interrupts-extended = <&tlmm 92 IRQ_TYPE_LEVEL_LOW>;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&i2c12_hid_active>;
> +	};
> +};
> +
> +&qupv3_id_0 {
> +	status = "okay";
> +};
> +
> +&qupv3_id_1 {
> +	status = "okay";
> +};
> +
> +&tlmm {
> +	gpio-reserved-ranges = <0 4>, <81 4>;
> +
> +	i2c2_hid_active: i2c2-hid-active {
> +		pins = <37>;
> +		function = "gpio";
> +
> +		input-enable;
> +		bias-pull-up;
> +		drive-strength = <2>;
> +	};
> +
> +	i2c6_hid_active: i2c6-hid-active {
> +		pins = <125>;
> +		function = "gpio";
> +
> +		input-enable;
> +		bias-pull-up;
> +		drive-strength = <2>;
> +	};
> +
> +	i2c12_hid_active: i2c12-hid-active {
> +		pins = <92>;
> +		function = "gpio";
> +
> +		input-enable;
> +		bias-pull-up;
> +		drive-strength = <2>;
> +	};
> +};
> +
> +&uart6 {
> +       status = "okay";
> +
> +       bluetooth {
> +	       compatible = "qcom,wcn3990-bt";
> +
> +	       vddio-supply = <&vreg_s4a_1p8>;
> +	       vddxo-supply = <&vreg_l7a_1p8>;
> +	       vddrf-supply = <&vreg_l17a_1p3>;
> +	       vddch0-supply = <&vreg_l25a_3p3>;
> +	       max-speed = <3200000>;
> +       };
> +};
> +
> +&ufs_mem_hc {
> +	status = "okay";
> +
> +	vcc-supply = <&vreg_l20a_2p95>;
> +	vcc-max-microamp = <600000>;
> +};
> +
> +&ufs_mem_phy {
> +	status = "okay";
> +
> +	vdda-phy-supply = <&vdda_ufs1_core>;
> +	vdda-pll-supply = <&vdda_ufs1_1p2>;
> +};
> +
> +&usb_1 {
> +	status = "okay";
> +};
> +
> +&usb_1_dwc3 {
> +	dr_mode = "host";
> +};
> +
> +&usb_1_hsphy {
> +	status = "okay";
> +
> +	vdd-supply = <&vdda_usb1_ss_core>;
> +	vdda-pll-supply = <&vdda_qusb_hs0_1p8>;
> +	vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>;
> +
> +	qcom,imp-res-offset-value = <8>;
> +	qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
> +	qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
> +	qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
> +};
> +
> +&usb_1_qmpphy {
> +	status = "okay";
> +
> +	vdda-phy-supply = <&vdda_usb1_ss_1p2>;
> +	vdda-pll-supply = <&vdda_usb1_ss_core>;
> +};
> +
> +&usb_2 {
> +	status = "okay";
> +};
> +
> +&usb_2_dwc3 {
> +	dr_mode = "host";
> +};
> +
> +&usb_2_hsphy {
> +	status = "okay";
> +
> +	vdd-supply = <&vdda_usb2_ss_core>;
> +	vdda-pll-supply = <&vdda_qusb_hs0_1p8>;
> +	vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>;
> +
> +	qcom,imp-res-offset-value = <8>;
> +	qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_22_8_MA>;
> +};
> +
> +&usb_2_qmpphy {
> +	status = "okay";
> +
> +	vdda-phy-supply = <&vdda_usb2_ss_1p2>;
> +	vdda-pll-supply = <&vdda_usb2_ss_core>;
> +};
> +
> +&qup_i2c12_default {
> +	drive-strength = <2>;
> +	bias-disable;
> +};
> +
> +&qup_uart6_default {
> +       pinmux {
> +               pins = "gpio45", "gpio46", "gpio47", "gpio48";
> +               function = "qup6";
> +       };
> +
> +       cts {
> +	       pins = "gpio45";
> +	       bias-pull-down;
> +       };
> +
> +       rts-tx {
> +	       pins = "gpio46", "gpio47";
> +	       drive-strength = <2>;
> +	       bias-disable;
> +       };
> +
> +       rx {
> +	       pins = "gpio48";
> +	       bias-pull-up;
> +       };
> +};
> -- 
> 2.17.1
>
Lee Jones Sept. 3, 2019, 6:20 a.m. UTC | #2
On Mon, 02 Sep 2019, Bjorn Andersson wrote:

> On Mon 02 Sep 06:24 PDT 2019, Lee Jones wrote:
> 
> > From: Bjorn Andersson <bjorn.andersson@linaro.org>
> > 
> > The Lenovo Yoga C630 is built on the SDM850 from Qualcomm, but this seem
> > to be similar enough to the SDM845 that we can reuse the sdm845.dtsi.
> > 
> > Supported by this patch is: keyboard, battery monitoring, UFS storage,
> > USB host and Bluetooth.
> 
> Applied this to next-20190829 and booted it, got a little bit of EFI FB,
> then the screen goes blank and after a while I'm back in GRUB.
> 
> I've not been able to figure out what's causing this though.

Probably DMA.  There is still an issue in the COM GENI Serial Engine
Driver which reboots the system when a DMA transaction is initiated.

However, with a workaround patch applied to the Serial Engine driver
(drivers/soc/qcom/qcom-geni-se.c) this DTS has no issue booting the
system.

We have ~12 weeks to either fix or elegantly work around the Serial
Engine issue.  IMHO is makes no sense to hold back this enablement
patch (which cannot go in via the -rcs) for something which is likely
to be fixed and applied during v3.4-rcX.
Lee Jones Sept. 3, 2019, 6:21 a.m. UTC | #3
On Tue, 03 Sep 2019, Lee Jones wrote:

> On Mon, 02 Sep 2019, Bjorn Andersson wrote:
> 
> > On Mon 02 Sep 06:24 PDT 2019, Lee Jones wrote:
> > 
> > > From: Bjorn Andersson <bjorn.andersson@linaro.org>
> > > 
> > > The Lenovo Yoga C630 is built on the SDM850 from Qualcomm, but this seem
> > > to be similar enough to the SDM845 that we can reuse the sdm845.dtsi.
> > > 
> > > Supported by this patch is: keyboard, battery monitoring, UFS storage,
> > > USB host and Bluetooth.
> > 
> > Applied this to next-20190829 and booted it, got a little bit of EFI FB,
> > then the screen goes blank and after a while I'm back in GRUB.
> > 
> > I've not been able to figure out what's causing this though.
> 
> Probably DMA.  There is still an issue in the COM GENI Serial Engine
> Driver which reboots the system when a DMA transaction is initiated.
> 
> However, with a workaround patch applied to the Serial Engine driver
> (drivers/soc/qcom/qcom-geni-se.c) this DTS has no issue booting the
> system.
> 
> We have ~12 weeks to either fix or elegantly work around the Serial
> Engine issue.  IMHO is makes no sense to hold back this enablement
> patch (which cannot go in via the -rcs) for something which is likely
> to be fixed and applied during v3.4-rcX.

NB: If you're worried about other entities thinking the platform boots
fault free due to this DTS patch being applied, I would suggest we
place a little "NB:" note in the changelog to explain the situation.
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 0a7e5dfce6f7..670c6c65f9e9 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -12,5 +12,6 @@  dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r3.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-db845c.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-mtp.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sdm850-lenovo-yoga-c630.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-1000.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-4000.dtb
diff --git a/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts b/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts
new file mode 100644
index 000000000000..3177b054035f
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts
@@ -0,0 +1,450 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Lenovo Yoga C630
+ *
+ * Copyright (c) 2019, Linaro Ltd.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sdm845.dtsi"
+#include "pm8998.dtsi"
+
+/ {
+	model = "Lenovo Yoga C630";
+	compatible = "lenovo,yoga-c630", "qcom,sdm845";
+
+	aliases {
+		hsuart0 = &uart6;
+	};
+};
+
+&apps_rsc {
+	pm8998-rpmh-regulators {
+		compatible = "qcom,pm8998-rpmh-regulators";
+		qcom,pmic-id = "a";
+
+		vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>;
+		vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>;
+
+		vreg_s2a_1p125: smps2 {
+		};
+
+		vreg_s3a_1p35: smps3 {
+			regulator-min-microvolt = <1352000>;
+			regulator-max-microvolt = <1352000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s4a_1p8: smps4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s5a_2p04: smps5 {
+			regulator-min-microvolt = <2040000>;
+			regulator-max-microvolt = <2040000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s7a_1p025: smps7 {
+		};
+
+		vdd_qusb_hs0:
+		vdda_hp_pcie_core:
+		vdda_mipi_csi0_0p9:
+		vdda_mipi_csi1_0p9:
+		vdda_mipi_csi2_0p9:
+		vdda_mipi_dsi0_pll:
+		vdda_mipi_dsi1_pll:
+		vdda_qlink_lv:
+		vdda_qlink_lv_ck:
+		vdda_qrefs_0p875:
+		vdda_pcie_core:
+		vdda_pll_cc_ebi01:
+		vdda_pll_cc_ebi23:
+		vdda_sp_sensor:
+		vdda_ufs1_core:
+		vdda_ufs2_core:
+		vdda_usb1_ss_core:
+		vdda_usb2_ss_core:
+		vreg_l1a_0p875: ldo1 {
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vddpx_10:
+		vreg_l2a_1p2: ldo2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l3a_1p0: ldo3 {
+		};
+
+		vdd_wcss_cx:
+		vdd_wcss_mx:
+		vdda_wcss_pll:
+		vreg_l5a_0p8: ldo5 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vddpx_13:
+		vreg_l6a_1p8: ldo6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7a_1p8: ldo7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8a_1p2: ldo8 {
+		};
+
+		vreg_l9a_1p8: ldo9 {
+		};
+
+		vreg_l10a_1p8: ldo10 {
+		};
+
+		vreg_l11a_1p0: ldo11 {
+		};
+
+		vdd_qfprom:
+		vdd_qfprom_sp:
+		vdda_apc1_cs_1p8:
+		vdda_gfx_cs_1p8:
+		vdda_qrefs_1p8:
+		vdda_qusb_hs0_1p8:
+		vddpx_11:
+		vreg_l12a_1p8: ldo12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vddpx_2:
+		vreg_l13a_2p95: ldo13 {
+		};
+
+		vreg_l14a_1p88: ldo14 {
+			regulator-min-microvolt = <1880000>;
+			regulator-max-microvolt = <1880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15a_1p8: ldo15 {
+		};
+
+		vreg_l16a_2p7: ldo16 {
+		};
+
+		vreg_l17a_1p3: ldo17 {
+			regulator-min-microvolt = <1304000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l18a_2p7: ldo18 {
+		};
+
+		vreg_l19a_3p0: ldo19 {
+			regulator-min-microvolt = <3100000>;
+			regulator-max-microvolt = <3108000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l20a_2p95: ldo20 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l21a_2p95: ldo21 {
+		};
+
+		vreg_l22a_2p85: ldo22 {
+		};
+
+		vreg_l23a_3p3: ldo23 {
+		};
+
+		vdda_qusb_hs0_3p1:
+		vreg_l24a_3p075: ldo24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3083000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l25a_3p3: ldo25 {
+			regulator-min-microvolt = <3104000>;
+			regulator-max-microvolt = <3112000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdda_hp_pcie_1p2:
+		vdda_hv_ebi0:
+		vdda_hv_ebi1:
+		vdda_hv_ebi2:
+		vdda_hv_ebi3:
+		vdda_mipi_csi_1p25:
+		vdda_mipi_dsi0_1p2:
+		vdda_mipi_dsi1_1p2:
+		vdda_pcie_1p2:
+		vdda_ufs1_1p2:
+		vdda_ufs2_1p2:
+		vdda_usb1_ss_1p2:
+		vdda_usb2_ss_1p2:
+		vreg_l26a_1p2: ldo26 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1208000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l28a_3p0: ldo28 {
+		};
+
+		vreg_lvs1a_1p8: lvs1 {
+		};
+
+		vreg_lvs2a_1p8: lvs2 {
+		};
+	};
+};
+
+&apps_smmu {
+	/* TODO: Figure out how to survive booting with this enabled */
+	status = "disabled";
+};
+
+&gcc {
+	protected-clocks = <GCC_QSPI_CORE_CLK>,
+			   <GCC_QSPI_CORE_CLK_SRC>,
+			   <GCC_QSPI_CNOC_PERIPH_AHB_CLK>;
+};
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	battery@70 {
+		compatible = "some,battery";
+		reg = <0x70>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	hid@15 {
+		compatible = "hid-over-i2c";
+		reg = <0x15>;
+		hid-descr-addr = <0x1>;
+
+		interrupts-extended = <&tlmm 37 IRQ_TYPE_EDGE_RISING>;
+	};
+
+	hid@2c {
+		compatible = "hid-over-i2c";
+		reg = <0x2c>;
+		hid-descr-addr = <0x20>;
+
+		interrupts-extended = <&tlmm 37 IRQ_TYPE_EDGE_RISING>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c2_hid_active>;
+	};
+};
+
+&i2c5 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	hid@10 {
+		compatible = "hid-over-i2c";
+		reg = <0x10>;
+		hid-descr-addr = <0x1>;
+
+		interrupts-extended = <&tlmm 125 IRQ_TYPE_EDGE_FALLING>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c6_hid_active>;
+	};
+};
+
+&i2c11 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	hid@5c {
+		compatible = "hid-over-i2c";
+		reg = <0x5c>;
+		hid-descr-addr = <0x1>;
+
+		interrupts-extended = <&tlmm 92 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c12_hid_active>;
+	};
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&tlmm {
+	gpio-reserved-ranges = <0 4>, <81 4>;
+
+	i2c2_hid_active: i2c2-hid-active {
+		pins = <37>;
+		function = "gpio";
+
+		input-enable;
+		bias-pull-up;
+		drive-strength = <2>;
+	};
+
+	i2c6_hid_active: i2c6-hid-active {
+		pins = <125>;
+		function = "gpio";
+
+		input-enable;
+		bias-pull-up;
+		drive-strength = <2>;
+	};
+
+	i2c12_hid_active: i2c12-hid-active {
+		pins = <92>;
+		function = "gpio";
+
+		input-enable;
+		bias-pull-up;
+		drive-strength = <2>;
+	};
+};
+
+&uart6 {
+       status = "okay";
+
+       bluetooth {
+	       compatible = "qcom,wcn3990-bt";
+
+	       vddio-supply = <&vreg_s4a_1p8>;
+	       vddxo-supply = <&vreg_l7a_1p8>;
+	       vddrf-supply = <&vreg_l17a_1p3>;
+	       vddch0-supply = <&vreg_l25a_3p3>;
+	       max-speed = <3200000>;
+       };
+};
+
+&ufs_mem_hc {
+	status = "okay";
+
+	vcc-supply = <&vreg_l20a_2p95>;
+	vcc-max-microamp = <600000>;
+};
+
+&ufs_mem_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vdda_ufs1_core>;
+	vdda-pll-supply = <&vdda_ufs1_1p2>;
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_1_hsphy {
+	status = "okay";
+
+	vdd-supply = <&vdda_usb1_ss_core>;
+	vdda-pll-supply = <&vdda_qusb_hs0_1p8>;
+	vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>;
+
+	qcom,imp-res-offset-value = <8>;
+	qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
+	qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
+	qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
+};
+
+&usb_1_qmpphy {
+	status = "okay";
+
+	vdda-phy-supply = <&vdda_usb1_ss_1p2>;
+	vdda-pll-supply = <&vdda_usb1_ss_core>;
+};
+
+&usb_2 {
+	status = "okay";
+};
+
+&usb_2_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_2_hsphy {
+	status = "okay";
+
+	vdd-supply = <&vdda_usb2_ss_core>;
+	vdda-pll-supply = <&vdda_qusb_hs0_1p8>;
+	vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>;
+
+	qcom,imp-res-offset-value = <8>;
+	qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_22_8_MA>;
+};
+
+&usb_2_qmpphy {
+	status = "okay";
+
+	vdda-phy-supply = <&vdda_usb2_ss_1p2>;
+	vdda-pll-supply = <&vdda_usb2_ss_core>;
+};
+
+&qup_i2c12_default {
+	drive-strength = <2>;
+	bias-disable;
+};
+
+&qup_uart6_default {
+       pinmux {
+               pins = "gpio45", "gpio46", "gpio47", "gpio48";
+               function = "qup6";
+       };
+
+       cts {
+	       pins = "gpio45";
+	       bias-pull-down;
+       };
+
+       rts-tx {
+	       pins = "gpio46", "gpio47";
+	       drive-strength = <2>;
+	       bias-disable;
+       };
+
+       rx {
+	       pins = "gpio48";
+	       bias-pull-up;
+       };
+};