| Message ID | 1567950178-4466-2-git-send-email-narmstrong@baylibre.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | arm64: dts: meson-g12: add support for PCIe | expand |
On Sun, Sep 08, 2019 at 01:42:53PM +0000, Neil Armstrong wrote: > Add PCIE bindings for the Amlogic G12A SoC, the support is the same > but the PHY is shared with USB3 to control the differential lines. > > Thus this adds a phy phandle to control the PHY, and sets invalid > MIPI clock as optional for G12A. Perhaps reword to "Thus this adds a phy phandle to control the PHY, and only requires a MIPI clock for AXG SoC Family". Thanks, Andrew Murray > > Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> > --- > .../devicetree/bindings/pci/amlogic,meson-pcie.txt | 12 ++++++++---- > 1 file changed, 8 insertions(+), 4 deletions(-) > > diff --git a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt > index efa2c8b9b85a..84fdc422792e 100644 > --- a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt > +++ b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt > @@ -9,13 +9,16 @@ Additional properties are described here: > > Required properties: > - compatible: > - should contain "amlogic,axg-pcie" to identify the core. > + should contain : > + - "amlogic,axg-pcie" for AXG SoC Family > + - "amlogic,g12a-pcie" for G12A SoC Family > + to identify the core. > - reg: > should contain the configuration address space. > - reg-names: Must be > - "elbi" External local bus interface registers > - "cfg" Meson specific registers > - - "phy" Meson PCIE PHY registers > + - "phy" Meson PCIE PHY registers for AXG SoC Family > - "config" PCIe configuration space > - reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal. > - clocks: Must contain an entry for each entry in clock-names. > @@ -23,12 +26,13 @@ Required properties: > - "pclk" PCIe GEN 100M PLL clock > - "port" PCIe_x(A or B) RC clock gate > - "general" PCIe Phy clock > - - "mipi" PCIe_x(A or B) 100M ref clock gate > + - "mipi" PCIe_x(A or B) 100M ref clock gate for AXG SoC Family > - resets: phandle to the reset lines. > - reset-names: must contain "phy" "port" and "apb" > - - "phy" Share PHY reset > + - "phy" Share PHY reset for AXG SoC Family > - "port" Port A or B reset > - "apb" Share APB reset > +- phys: should contain a phandle to the shared phy for G12A SoC Family > - device_type: > should be "pci". As specified in designware-pcie.txt > > -- > 2.17.1 >
Hi Andrew, On 11/09/2019 14:22, Andrew Murray wrote: > On Sun, Sep 08, 2019 at 01:42:53PM +0000, Neil Armstrong wrote: >> Add PCIE bindings for the Amlogic G12A SoC, the support is the same >> but the PHY is shared with USB3 to control the differential lines. >> >> Thus this adds a phy phandle to control the PHY, and sets invalid >> MIPI clock as optional for G12A. > > Perhaps reword to "Thus this adds a phy phandle to control the PHY, > and only requires a MIPI clock for AXG SoC Family". Sure, thanks, Neil > > Thanks, > > Andrew Murray > >> >> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> >> --- >> .../devicetree/bindings/pci/amlogic,meson-pcie.txt | 12 ++++++++---- >> 1 file changed, 8 insertions(+), 4 deletions(-) >> >> diff --git a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt >> index efa2c8b9b85a..84fdc422792e 100644 >> --- a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt >> +++ b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt >> @@ -9,13 +9,16 @@ Additional properties are described here: >> >> Required properties: >> - compatible: >> - should contain "amlogic,axg-pcie" to identify the core. >> + should contain : >> + - "amlogic,axg-pcie" for AXG SoC Family >> + - "amlogic,g12a-pcie" for G12A SoC Family >> + to identify the core. >> - reg: >> should contain the configuration address space. >> - reg-names: Must be >> - "elbi" External local bus interface registers >> - "cfg" Meson specific registers >> - - "phy" Meson PCIE PHY registers >> + - "phy" Meson PCIE PHY registers for AXG SoC Family >> - "config" PCIe configuration space >> - reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal. >> - clocks: Must contain an entry for each entry in clock-names. >> @@ -23,12 +26,13 @@ Required properties: >> - "pclk" PCIe GEN 100M PLL clock >> - "port" PCIe_x(A or B) RC clock gate >> - "general" PCIe Phy clock >> - - "mipi" PCIe_x(A or B) 100M ref clock gate >> + - "mipi" PCIe_x(A or B) 100M ref clock gate for AXG SoC Family >> - resets: phandle to the reset lines. >> - reset-names: must contain "phy" "port" and "apb" >> - - "phy" Share PHY reset >> + - "phy" Share PHY reset for AXG SoC Family >> - "port" Port A or B reset >> - "apb" Share APB reset >> +- phys: should contain a phandle to the shared phy for G12A SoC Family >> - device_type: >> should be "pci". As specified in designware-pcie.txt >> >> -- >> 2.17.1 >>
On Sun, 8 Sep 2019 13:42:53 +0000, Neil Armstrong wrote: > Add PCIE bindings for the Amlogic G12A SoC, the support is the same > but the PHY is shared with USB3 to control the differential lines. > > Thus this adds a phy phandle to control the PHY, and sets invalid > MIPI clock as optional for G12A. > > Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> > --- > .../devicetree/bindings/pci/amlogic,meson-pcie.txt | 12 ++++++++---- > 1 file changed, 8 insertions(+), 4 deletions(-) > Reviewed-by: Rob Herring <robh@kernel.org>
diff --git a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt index efa2c8b9b85a..84fdc422792e 100644 --- a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt +++ b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt @@ -9,13 +9,16 @@ Additional properties are described here: Required properties: - compatible: - should contain "amlogic,axg-pcie" to identify the core. + should contain : + - "amlogic,axg-pcie" for AXG SoC Family + - "amlogic,g12a-pcie" for G12A SoC Family + to identify the core. - reg: should contain the configuration address space. - reg-names: Must be - "elbi" External local bus interface registers - "cfg" Meson specific registers - - "phy" Meson PCIE PHY registers + - "phy" Meson PCIE PHY registers for AXG SoC Family - "config" PCIe configuration space - reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal. - clocks: Must contain an entry for each entry in clock-names. @@ -23,12 +26,13 @@ Required properties: - "pclk" PCIe GEN 100M PLL clock - "port" PCIe_x(A or B) RC clock gate - "general" PCIe Phy clock - - "mipi" PCIe_x(A or B) 100M ref clock gate + - "mipi" PCIe_x(A or B) 100M ref clock gate for AXG SoC Family - resets: phandle to the reset lines. - reset-names: must contain "phy" "port" and "apb" - - "phy" Share PHY reset + - "phy" Share PHY reset for AXG SoC Family - "port" Port A or B reset - "apb" Share APB reset +- phys: should contain a phandle to the shared phy for G12A SoC Family - device_type: should be "pci". As specified in designware-pcie.txt
Add PCIE bindings for the Amlogic G12A SoC, the support is the same but the PHY is shared with USB3 to control the differential lines. Thus this adds a phy phandle to control the PHY, and sets invalid MIPI clock as optional for G12A. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> --- .../devicetree/bindings/pci/amlogic,meson-pcie.txt | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-)