Message ID | 1568135676-9328-5-git-send-email-thara.gopinath@linaro.org (mailing list archive) |
---|---|
State | New, archived |
Delegated to: | Eduardo Valentin |
Headers | show |
Series | Introduce Power domain based warming device driver | expand |
On Tue, 10 Sep 2019 at 19:14, Thara Gopinath <thara.gopinath@linaro.org> wrote: > > Resources modeled as power domains in linux kenrel > can be used to warm the SoC(eg. mx power domain on sdm845). > To support this feature, introduce a generic power domain > warming device driver that can be plugged into the thermal framework > (The thermal framework itself requires further modifiction to > support a warming device in place of a cooling device. > Those extensions are not introduced in this patch series). > > Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org> > --- > v1->v2: > - Make power domain based warming device driver a generic > driver in the thermal framework. v1 implemented this as a > Qualcomm specific driver. > - Rename certain variables as per review suggestions on the > mailing list. > > drivers/thermal/Kconfig | 11 +++ > drivers/thermal/Makefile | 2 + > drivers/thermal/pwr_domain_warming.c | 174 +++++++++++++++++++++++++++++++++++ > 3 files changed, 187 insertions(+) > create mode 100644 drivers/thermal/pwr_domain_warming.c > > diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig > index 9966364..eeb6018 100644 > --- a/drivers/thermal/Kconfig > +++ b/drivers/thermal/Kconfig > @@ -187,6 +187,17 @@ config DEVFREQ_THERMAL > > If you want this support, you should say Y here. > > +config PWR_DOMAIN_WARMING_THERMAL > + bool "Power Domain based warming device" > + depends on PM_GENERIC_DOMAINS > + depends on PM_GENERIC_DOMAINS_OF PM_GENERIC_DOMAINS_OF can't be set unless PM_GENERIC_DOMAINS is set too. So I assume it's sufficient to depend on PM_GENERIC_DOMAINS_OF? > + help > + This implements the generic power domain based warming > + mechanism through increasing the performance state of > + a power domain. > + > + If you want this support, you should say Y here. > + > config THERMAL_EMULATION > bool "Thermal emulation mode support" > help > diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile > index 74a37c7..382c64a 100644 > --- a/drivers/thermal/Makefile > +++ b/drivers/thermal/Makefile > @@ -27,6 +27,8 @@ thermal_sys-$(CONFIG_CLOCK_THERMAL) += clock_cooling.o > # devfreq cooling > thermal_sys-$(CONFIG_DEVFREQ_THERMAL) += devfreq_cooling.o > > +thermal_sys-$(CONFIG_PWR_DOMAIN_WARMING_THERMAL) += pwr_domain_warming.o > + > # platform thermal drivers > obj-y += broadcom/ > obj-$(CONFIG_THERMAL_MMIO) += thermal_mmio.o > diff --git a/drivers/thermal/pwr_domain_warming.c b/drivers/thermal/pwr_domain_warming.c > new file mode 100644 > index 0000000..3dd792b > --- /dev/null > +++ b/drivers/thermal/pwr_domain_warming.c > @@ -0,0 +1,174 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Copyright (c) 2019, Linaro Ltd > + */ > +#include <linux/err.h> > +#include <linux/kernel.h> > +#include <linux/init.h> > +#include <linux/of_device.h> > +#include <linux/platform_device.h> > +#include <linux/module.h> > +#include <linux/pm_domain.h> > +#include <linux/pm_runtime.h> > +#include <linux/thermal.h> > + > +struct pd_warming_device { > + struct thermal_cooling_device *cdev; > + struct device *dev; > + int max_state; > + int cur_state; > + bool runtime_resumed; > +}; > + > +static const struct of_device_id pd_wdev_match_table[] = { > + { .compatible = "thermal-power-domain-wdev", .data = NULL }, > + { } > +}; > +MODULE_DEVICE_TABLE(of, pd_wdev_match_table); > + > +static int pd_wdev_get_max_state(struct thermal_cooling_device *cdev, > + unsigned long *state) > +{ > + struct pd_warming_device *pd_wdev = cdev->devdata; > + > + *state = pd_wdev->max_state; > + return 0; > +} > + > +static int pd_wdev_get_cur_state(struct thermal_cooling_device *cdev, > + unsigned long *state) > +{ > + struct pd_warming_device *pd_wdev = cdev->devdata; > + > + *state = dev_pm_genpd_get_performance_state(pd_wdev->dev); > + > + return 0; > +} > + > +static int pd_wdev_set_cur_state(struct thermal_cooling_device *cdev, > + unsigned long state) > +{ > + struct pd_warming_device *pd_wdev = cdev->devdata; > + struct device *dev = pd_wdev->dev; > + int ret; > + > + ret = dev_pm_genpd_set_performance_state(dev, state); > + > + if (ret) > + return ret; > + > + if (state && !pd_wdev->runtime_resumed) { > + ret = pm_runtime_get_sync(dev); > + pd_wdev->runtime_resumed = true; > + } else if (!state && pd_wdev->runtime_resumed) { > + ret = pm_runtime_put(dev); > + pd_wdev->runtime_resumed = false; > + } > + > + return ret; > +} > + > +static struct thermal_cooling_device_ops pd_warming_device_ops = { > + .get_max_state = pd_wdev_get_max_state, > + .get_cur_state = pd_wdev_get_cur_state, > + .set_cur_state = pd_wdev_set_cur_state, > +}; > + > +static int pd_wdev_create(struct device *dev, const char *name) > +{ > + struct pd_warming_device *pd_wdev; > + int state_count; > + > + pd_wdev = devm_kzalloc(dev, sizeof(*pd_wdev), GFP_KERNEL); > + if (!pd_wdev) > + return -ENOMEM; > + > + state_count = dev_pm_genpd_performance_state_count(dev); > + if (state_count < 0) > + return state_count; > + > + pd_wdev->dev = dev; > + pd_wdev->max_state = state_count - 1; > + pd_wdev->runtime_resumed = false; > + > + pm_runtime_enable(dev); > + > + pd_wdev->cdev = thermal_of_cooling_device_register > + (dev->of_node, name, > + pd_wdev, > + &pd_warming_device_ops); > + if (IS_ERR(pd_wdev->cdev)) { > + dev_err(dev, "unable to register %s cooling device\n", name); > + pm_runtime_disable(dev); > + > + return PTR_ERR(pd_wdev->cdev); > + } > + > + return 0; > +} > + > +static int pd_wdev_probe(struct platform_device *pdev) > +{ > + struct device *dev = &pdev->dev, *pd_dev; > + const char *pd_name; > + int id, count, ret = 0; > + > + count = of_count_phandle_with_args(dev->of_node, "power-domains", > + "#power-domain-cells"); Perhaps this should be converted to genpd OF helper function instead, that allows the caller to know how many power-domains there are specified for a device node. > + > + if (count > 1) { > + for (id = 0; id < count; id++) { > + ret = of_property_read_string_index > + (dev->of_node, "power-domain-names", > + id, &pd_name); > + if (ret) { > + dev_err(dev, "Error reading the power domain name %d\n", ret); > + continue; > + } It looks a bit awkward that you want to re-use the power-domain-names as the name for the cooling (warming) device. This isn't really what we use the "*-names" bindings for in general, I think. Anyway, if you want a name corresponding to the actual attached PM domain, perhaps re-using "->name" from the struct generic_pm_domain is better. We can add a genpd helper for that, no problem. Of course it also means that you must call dev_pm_domain_attach_by_id() first, to attach the device and then get the name of the genpd, but that should be fine. > + > + pd_dev = dev_pm_domain_attach_by_id(dev, id); > + if (IS_ERR(pd_dev)) { > + dev_err(dev, "Error attaching power domain %s %ld\n", pd_name, PTR_ERR(pd_dev)); > + continue; > + } > + > + ret = pd_wdev_create(pd_dev, pd_name); > + if (ret) { > + dev_err(dev, "Error building cooling device %s %d\n", pd_name, ret); > + dev_pm_domain_detach(pd_dev, false); > + continue; > + } I am wondering about the use case of having multiple PM domains attached to the cooling (warming) device. Is that really needed? Perhaps you can elaborate on that a bit? > + } > + } else if (count == 1) { > + ret = of_property_read_string_index(dev->of_node, > + "power-domain-names", > + 0, &pd_name); > + if (ret) { > + dev_err(dev, "Error reading the power domain name %d\n", ret); > + goto exit; > + } According to my comment above, perhaps we simply don't have to use the "power-domain-names" binding at all. Also, I don't think this is really safe, as there is no guarantee that there is PM domain attached to the device, just because you found the DT property "power-domain-names". Probably better to check pm_domain pointer for the device. > + > + ret = pd_wdev_create(dev, pd_name); > + if (ret) { > + dev_err(dev, "Error building cooling device %s %d\n", pd_name, ret); > + goto exit; > + } > + } else { > + ret = -EINVAL; > + } > + > +exit: > + return ret; > +} > + > +static struct platform_driver pd_wdev_driver = { > + .driver = { > + .name = "qcom-rpmhpd-cdev", Probably rename to a more generic name (leftover from earlier version I assume). > + .of_match_table = pd_wdev_match_table, > + }, > + .probe = pd_wdev_probe, > +}; > +module_platform_driver(pd_wdev_driver); > + > +MODULE_DESCRIPTION("Qualcomm RPMHPD cooling device driver"); Ditto. > +MODULE_LICENSE("GPL v2"); > -- > 2.1.4 > Kind regards Uffe
On 09/12/2019 11:04 AM, Ulf Hansson wrote: Hi Ulf, Thanks for the review. > On Tue, 10 Sep 2019 at 19:14, Thara Gopinath <thara.gopinath@linaro.org> wrote: >> >> Resources modeled as power domains in linux kenrel >> can be used to warm the SoC(eg. mx power domain on sdm845). >> To support this feature, introduce a generic power domain >> warming device driver that can be plugged into the thermal framework >> (The thermal framework itself requires further modifiction to >> support a warming device in place of a cooling device. >> Those extensions are not introduced in this patch series). >> >> Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org> >> --- >> v1->v2: >> - Make power domain based warming device driver a generic >> driver in the thermal framework. v1 implemented this as a >> Qualcomm specific driver. >> - Rename certain variables as per review suggestions on the >> mailing list. >> >> drivers/thermal/Kconfig | 11 +++ >> drivers/thermal/Makefile | 2 + >> drivers/thermal/pwr_domain_warming.c | 174 +++++++++++++++++++++++++++++++++++ >> 3 files changed, 187 insertions(+) >> create mode 100644 drivers/thermal/pwr_domain_warming.c >> >> diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig >> index 9966364..eeb6018 100644 >> --- a/drivers/thermal/Kconfig >> +++ b/drivers/thermal/Kconfig >> @@ -187,6 +187,17 @@ config DEVFREQ_THERMAL >> >> If you want this support, you should say Y here. >> >> +config PWR_DOMAIN_WARMING_THERMAL >> + bool "Power Domain based warming device" >> + depends on PM_GENERIC_DOMAINS >> + depends on PM_GENERIC_DOMAINS_OF > > PM_GENERIC_DOMAINS_OF can't be set unless PM_GENERIC_DOMAINS is set too. > > So I assume it's sufficient to depend on PM_GENERIC_DOMAINS_OF? Yes, you are right. I will change it. > >> + help >> + This implements the generic power domain based warming >> + mechanism through increasing the performance state of >> + a power domain. >> + >> + If you want this support, you should say Y here. >> + >> config THERMAL_EMULATION >> bool "Thermal emulation mode support" >> help >> diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile >> index 74a37c7..382c64a 100644 >> --- a/drivers/thermal/Makefile >> +++ b/drivers/thermal/Makefile >> @@ -27,6 +27,8 @@ thermal_sys-$(CONFIG_CLOCK_THERMAL) += clock_cooling.o >> # devfreq cooling >> thermal_sys-$(CONFIG_DEVFREQ_THERMAL) += devfreq_cooling.o >> >> +thermal_sys-$(CONFIG_PWR_DOMAIN_WARMING_THERMAL) += pwr_domain_warming.o >> + >> # platform thermal drivers >> obj-y += broadcom/ >> obj-$(CONFIG_THERMAL_MMIO) += thermal_mmio.o >> diff --git a/drivers/thermal/pwr_domain_warming.c b/drivers/thermal/pwr_domain_warming.c >> new file mode 100644 >> index 0000000..3dd792b >> --- /dev/null >> +++ b/drivers/thermal/pwr_domain_warming.c >> @@ -0,0 +1,174 @@ >> +// SPDX-License-Identifier: GPL-2.0 >> +/* >> + * Copyright (c) 2019, Linaro Ltd >> + */ >> +#include <linux/err.h> >> +#include <linux/kernel.h> >> +#include <linux/init.h> >> +#include <linux/of_device.h> >> +#include <linux/platform_device.h> >> +#include <linux/module.h> >> +#include <linux/pm_domain.h> >> +#include <linux/pm_runtime.h> >> +#include <linux/thermal.h> >> + >> +struct pd_warming_device { >> + struct thermal_cooling_device *cdev; >> + struct device *dev; >> + int max_state; >> + int cur_state; >> + bool runtime_resumed; >> +}; >> + >> +static const struct of_device_id pd_wdev_match_table[] = { >> + { .compatible = "thermal-power-domain-wdev", .data = NULL }, >> + { } >> +}; >> +MODULE_DEVICE_TABLE(of, pd_wdev_match_table); >> + >> +static int pd_wdev_get_max_state(struct thermal_cooling_device *cdev, >> + unsigned long *state) >> +{ >> + struct pd_warming_device *pd_wdev = cdev->devdata; >> + >> + *state = pd_wdev->max_state; >> + return 0; >> +} >> + >> +static int pd_wdev_get_cur_state(struct thermal_cooling_device *cdev, >> + unsigned long *state) >> +{ >> + struct pd_warming_device *pd_wdev = cdev->devdata; >> + >> + *state = dev_pm_genpd_get_performance_state(pd_wdev->dev); >> + >> + return 0; >> +} >> + >> +static int pd_wdev_set_cur_state(struct thermal_cooling_device *cdev, >> + unsigned long state) >> +{ >> + struct pd_warming_device *pd_wdev = cdev->devdata; >> + struct device *dev = pd_wdev->dev; >> + int ret; >> + >> + ret = dev_pm_genpd_set_performance_state(dev, state); >> + >> + if (ret) >> + return ret; >> + >> + if (state && !pd_wdev->runtime_resumed) { >> + ret = pm_runtime_get_sync(dev); >> + pd_wdev->runtime_resumed = true; >> + } else if (!state && pd_wdev->runtime_resumed) { >> + ret = pm_runtime_put(dev); >> + pd_wdev->runtime_resumed = false; >> + } >> + >> + return ret; >> +} >> + >> +static struct thermal_cooling_device_ops pd_warming_device_ops = { >> + .get_max_state = pd_wdev_get_max_state, >> + .get_cur_state = pd_wdev_get_cur_state, >> + .set_cur_state = pd_wdev_set_cur_state, >> +}; >> + >> +static int pd_wdev_create(struct device *dev, const char *name) >> +{ >> + struct pd_warming_device *pd_wdev; >> + int state_count; >> + >> + pd_wdev = devm_kzalloc(dev, sizeof(*pd_wdev), GFP_KERNEL); >> + if (!pd_wdev) >> + return -ENOMEM; >> + >> + state_count = dev_pm_genpd_performance_state_count(dev); >> + if (state_count < 0) >> + return state_count; >> + >> + pd_wdev->dev = dev; >> + pd_wdev->max_state = state_count - 1; >> + pd_wdev->runtime_resumed = false; >> + >> + pm_runtime_enable(dev); >> + >> + pd_wdev->cdev = thermal_of_cooling_device_register >> + (dev->of_node, name, >> + pd_wdev, >> + &pd_warming_device_ops); >> + if (IS_ERR(pd_wdev->cdev)) { >> + dev_err(dev, "unable to register %s cooling device\n", name); >> + pm_runtime_disable(dev); >> + >> + return PTR_ERR(pd_wdev->cdev); >> + } >> + >> + return 0; >> +} >> + >> +static int pd_wdev_probe(struct platform_device *pdev) >> +{ >> + struct device *dev = &pdev->dev, *pd_dev; >> + const char *pd_name; >> + int id, count, ret = 0; >> + >> + count = of_count_phandle_with_args(dev->of_node, "power-domains", >> + "#power-domain-cells"); > > Perhaps this should be converted to genpd OF helper function instead, > that allows the caller to know how many power-domains there are > specified for a device node. I am ok with this if you think that a OF helper to get the number of power domains is a useful helper in the genpd framework. I can add it as part of the next revision. Or do you want me to send it across separate? > >> + >> + if (count > 1) { >> + for (id = 0; id < count; id++) { >> + ret = of_property_read_string_index >> + (dev->of_node, "power-domain-names", >> + id, &pd_name); >> + if (ret) { >> + dev_err(dev, "Error reading the power domain name %d\n", ret); >> + continue; >> + } > > It looks a bit awkward that you want to re-use the power-domain-names > as the name for the cooling (warming) device. This isn't really what > we use the "*-names" bindings for in general, I think. > > Anyway, if you want a name corresponding to the actual attached PM > domain, perhaps re-using "->name" from the struct generic_pm_domain is > better. We can add a genpd helper for that, no problem. Of course it > also means that you must call dev_pm_domain_attach_by_id() first, to > attach the device and then get the name of the genpd, but that should > be fine. Ya. I need a name corresponding to the power domain name (or something very close) to identify the actual warming device in the sysfs entries. I can use genpd->name and a helper function to achieve it. I can include it in Patch 1/5 where I add other helper functions. > >> + >> + pd_dev = dev_pm_domain_attach_by_id(dev, id); >> + if (IS_ERR(pd_dev)) { >> + dev_err(dev, "Error attaching power domain %s %ld\n", pd_name, PTR_ERR(pd_dev)); >> + continue; >> + } >> + >> + ret = pd_wdev_create(pd_dev, pd_name); >> + if (ret) { >> + dev_err(dev, "Error building cooling device %s %d\n", pd_name, ret); >> + dev_pm_domain_detach(pd_dev, false); >> + continue; >> + } > > I am wondering about the use case of having multiple PM domains > attached to the cooling (warming) device. Is that really needed? > Perhaps you can elaborate on that a bit? Ya. I though about this as well. I don't have a use case. In my current case it is just one power domain on the SoC. But considering this is now a generic driver, in my opinion this has to be a generic solution. So if you think about this, the device should be able to specify any number of power domains that can behave as a warming device since a SoC can have any number of power domain based warming devices. May be one to warm up the cpus, one for gpus etc. So another way of implementing this whole thing is to avoid having a special power domain warming device defined in the device tree. Instead, add a few new binding to the power-domain controller/provider entries to specify if a power domain controlled by the provider can act as a warming device or not. And have the initialization code for the power domain controller (of_genpd_add_provider_onecell or any other suitable API) register the specified power domain as a warming device. The DT entries should probably look something like below in the case. rpmhpd: power-controller { compatible = "qcom,sdm845-rpmhpd"; #power-domain-cells = <1>; hosts-warming-dev; warming-dev-names = "mx"; operating-points-v2 = <&rpmhpd_opp_table>; rpmhpd_opp_table: opp-table { compatible = "operating-points-v2"; .... And have the following in of_genpd_add_provider_onecell if (hosts-warming-dev) # loop through the warming-dev-names and register them as power domain warming devices. You think this is a better idea? > >> + } >> + } else if (count == 1) { >> + ret = of_property_read_string_index(dev->of_node, >> + "power-domain-names", >> + 0, &pd_name); >> + if (ret) { >> + dev_err(dev, "Error reading the power domain name %d\n", ret); >> + goto exit; >> + } > > According to my comment above, perhaps we simply don't have to use the > "power-domain-names" binding at all. I will use genpd->name > > Also, I don't think this is really safe, as there is no guarantee that > there is PM domain attached to the device, just because you found the > DT property "power-domain-names". > > Probably better to check pm_domain pointer for the device. > >> + >> + ret = pd_wdev_create(dev, pd_name); >> + if (ret) { >> + dev_err(dev, "Error building cooling device %s %d\n", pd_name, ret); >> + goto exit; >> + } >> + } else { >> + ret = -EINVAL; >> + } >> + >> +exit: >> + return ret; >> +} >> + >> +static struct platform_driver pd_wdev_driver = { >> + .driver = { >> + .name = "qcom-rpmhpd-cdev", > > Probably rename to a more generic name (leftover from earlier version I assume). Ya. I missed it . Will fix it. > >> + .of_match_table = pd_wdev_match_table, >> + }, >> + .probe = pd_wdev_probe, >> +}; >> +module_platform_driver(pd_wdev_driver); >> + >> +MODULE_DESCRIPTION("Qualcomm RPMHPD cooling device driver"); > > Ditto. Will fix it. > >> +MODULE_LICENSE("GPL v2"); >> -- >> 2.1.4 >> > > Kind regards > Uffe >
On Thu, 12 Sep 2019 at 22:18, Thara Gopinath <thara.gopinath@linaro.org> wrote: > > On 09/12/2019 11:04 AM, Ulf Hansson wrote: > > Hi Ulf, > > Thanks for the review. > > On Tue, 10 Sep 2019 at 19:14, Thara Gopinath <thara.gopinath@linaro.org> wrote: > >> > >> Resources modeled as power domains in linux kenrel > >> can be used to warm the SoC(eg. mx power domain on sdm845). > >> To support this feature, introduce a generic power domain > >> warming device driver that can be plugged into the thermal framework > >> (The thermal framework itself requires further modifiction to > >> support a warming device in place of a cooling device. > >> Those extensions are not introduced in this patch series). > >> > >> Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org> > >> --- > >> v1->v2: > >> - Make power domain based warming device driver a generic > >> driver in the thermal framework. v1 implemented this as a > >> Qualcomm specific driver. > >> - Rename certain variables as per review suggestions on the > >> mailing list. > >> > >> drivers/thermal/Kconfig | 11 +++ > >> drivers/thermal/Makefile | 2 + > >> drivers/thermal/pwr_domain_warming.c | 174 +++++++++++++++++++++++++++++++++++ > >> 3 files changed, 187 insertions(+) > >> create mode 100644 drivers/thermal/pwr_domain_warming.c > >> > >> diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig > >> index 9966364..eeb6018 100644 > >> --- a/drivers/thermal/Kconfig > >> +++ b/drivers/thermal/Kconfig > >> @@ -187,6 +187,17 @@ config DEVFREQ_THERMAL > >> > >> If you want this support, you should say Y here. > >> > >> +config PWR_DOMAIN_WARMING_THERMAL > >> + bool "Power Domain based warming device" > >> + depends on PM_GENERIC_DOMAINS > >> + depends on PM_GENERIC_DOMAINS_OF > > > > PM_GENERIC_DOMAINS_OF can't be set unless PM_GENERIC_DOMAINS is set too. > > > > So I assume it's sufficient to depend on PM_GENERIC_DOMAINS_OF? > > Yes, you are right. I will change it. > > > >> + help > >> + This implements the generic power domain based warming > >> + mechanism through increasing the performance state of > >> + a power domain. > >> + > >> + If you want this support, you should say Y here. > >> + > >> config THERMAL_EMULATION > >> bool "Thermal emulation mode support" > >> help > >> diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile > >> index 74a37c7..382c64a 100644 > >> --- a/drivers/thermal/Makefile > >> +++ b/drivers/thermal/Makefile > >> @@ -27,6 +27,8 @@ thermal_sys-$(CONFIG_CLOCK_THERMAL) += clock_cooling.o > >> # devfreq cooling > >> thermal_sys-$(CONFIG_DEVFREQ_THERMAL) += devfreq_cooling.o > >> > >> +thermal_sys-$(CONFIG_PWR_DOMAIN_WARMING_THERMAL) += pwr_domain_warming.o > >> + > >> # platform thermal drivers > >> obj-y += broadcom/ > >> obj-$(CONFIG_THERMAL_MMIO) += thermal_mmio.o > >> diff --git a/drivers/thermal/pwr_domain_warming.c b/drivers/thermal/pwr_domain_warming.c > >> new file mode 100644 > >> index 0000000..3dd792b > >> --- /dev/null > >> +++ b/drivers/thermal/pwr_domain_warming.c > >> @@ -0,0 +1,174 @@ > >> +// SPDX-License-Identifier: GPL-2.0 > >> +/* > >> + * Copyright (c) 2019, Linaro Ltd > >> + */ > >> +#include <linux/err.h> > >> +#include <linux/kernel.h> > >> +#include <linux/init.h> > >> +#include <linux/of_device.h> > >> +#include <linux/platform_device.h> > >> +#include <linux/module.h> > >> +#include <linux/pm_domain.h> > >> +#include <linux/pm_runtime.h> > >> +#include <linux/thermal.h> > >> + > >> +struct pd_warming_device { > >> + struct thermal_cooling_device *cdev; > >> + struct device *dev; > >> + int max_state; > >> + int cur_state; > >> + bool runtime_resumed; > >> +}; > >> + > >> +static const struct of_device_id pd_wdev_match_table[] = { > >> + { .compatible = "thermal-power-domain-wdev", .data = NULL }, > >> + { } > >> +}; > >> +MODULE_DEVICE_TABLE(of, pd_wdev_match_table); > >> + > >> +static int pd_wdev_get_max_state(struct thermal_cooling_device *cdev, > >> + unsigned long *state) > >> +{ > >> + struct pd_warming_device *pd_wdev = cdev->devdata; > >> + > >> + *state = pd_wdev->max_state; > >> + return 0; > >> +} > >> + > >> +static int pd_wdev_get_cur_state(struct thermal_cooling_device *cdev, > >> + unsigned long *state) > >> +{ > >> + struct pd_warming_device *pd_wdev = cdev->devdata; > >> + > >> + *state = dev_pm_genpd_get_performance_state(pd_wdev->dev); > >> + > >> + return 0; > >> +} > >> + > >> +static int pd_wdev_set_cur_state(struct thermal_cooling_device *cdev, > >> + unsigned long state) > >> +{ > >> + struct pd_warming_device *pd_wdev = cdev->devdata; > >> + struct device *dev = pd_wdev->dev; > >> + int ret; > >> + > >> + ret = dev_pm_genpd_set_performance_state(dev, state); > >> + > >> + if (ret) > >> + return ret; > >> + > >> + if (state && !pd_wdev->runtime_resumed) { > >> + ret = pm_runtime_get_sync(dev); > >> + pd_wdev->runtime_resumed = true; > >> + } else if (!state && pd_wdev->runtime_resumed) { > >> + ret = pm_runtime_put(dev); > >> + pd_wdev->runtime_resumed = false; > >> + } > >> + > >> + return ret; > >> +} > >> + > >> +static struct thermal_cooling_device_ops pd_warming_device_ops = { > >> + .get_max_state = pd_wdev_get_max_state, > >> + .get_cur_state = pd_wdev_get_cur_state, > >> + .set_cur_state = pd_wdev_set_cur_state, > >> +}; > >> + > >> +static int pd_wdev_create(struct device *dev, const char *name) > >> +{ > >> + struct pd_warming_device *pd_wdev; > >> + int state_count; > >> + > >> + pd_wdev = devm_kzalloc(dev, sizeof(*pd_wdev), GFP_KERNEL); > >> + if (!pd_wdev) > >> + return -ENOMEM; > >> + > >> + state_count = dev_pm_genpd_performance_state_count(dev); > >> + if (state_count < 0) > >> + return state_count; > >> + > >> + pd_wdev->dev = dev; > >> + pd_wdev->max_state = state_count - 1; > >> + pd_wdev->runtime_resumed = false; > >> + > >> + pm_runtime_enable(dev); > >> + > >> + pd_wdev->cdev = thermal_of_cooling_device_register > >> + (dev->of_node, name, > >> + pd_wdev, > >> + &pd_warming_device_ops); > >> + if (IS_ERR(pd_wdev->cdev)) { > >> + dev_err(dev, "unable to register %s cooling device\n", name); > >> + pm_runtime_disable(dev); > >> + > >> + return PTR_ERR(pd_wdev->cdev); > >> + } > >> + > >> + return 0; > >> +} > >> + > >> +static int pd_wdev_probe(struct platform_device *pdev) > >> +{ > >> + struct device *dev = &pdev->dev, *pd_dev; > >> + const char *pd_name; > >> + int id, count, ret = 0; > >> + > >> + count = of_count_phandle_with_args(dev->of_node, "power-domains", > >> + "#power-domain-cells"); > > > > Perhaps this should be converted to genpd OF helper function instead, > > that allows the caller to know how many power-domains there are > > specified for a device node. > > I am ok with this if you think that a OF helper to get the number of > power domains is a useful helper in the genpd framework. I can add it as > part of the next revision. Or do you want me to send it across separate? Feel free to include in the next version of the series. In case it's needed. > > > >> + > >> + if (count > 1) { > >> + for (id = 0; id < count; id++) { > >> + ret = of_property_read_string_index > >> + (dev->of_node, "power-domain-names", > >> + id, &pd_name); > >> + if (ret) { > >> + dev_err(dev, "Error reading the power domain name %d\n", ret); > >> + continue; > >> + } > > > > It looks a bit awkward that you want to re-use the power-domain-names > > as the name for the cooling (warming) device. This isn't really what > > we use the "*-names" bindings for in general, I think. > > > > Anyway, if you want a name corresponding to the actual attached PM > > domain, perhaps re-using "->name" from the struct generic_pm_domain is > > better. We can add a genpd helper for that, no problem. Of course it > > also means that you must call dev_pm_domain_attach_by_id() first, to > > attach the device and then get the name of the genpd, but that should > > be fine. > > Ya. I need a name corresponding to the power domain name (or something > very close) to identify the actual warming device in the sysfs entries. > I can use genpd->name and a helper function to achieve it. I can include > it in Patch 1/5 where I add other helper functions. A separate patch please, but yeah, fold it in into @subject series. > > > >> + > >> + pd_dev = dev_pm_domain_attach_by_id(dev, id); > >> + if (IS_ERR(pd_dev)) { > >> + dev_err(dev, "Error attaching power domain %s %ld\n", pd_name, PTR_ERR(pd_dev)); > >> + continue; > >> + } > >> + > >> + ret = pd_wdev_create(pd_dev, pd_name); > >> + if (ret) { > >> + dev_err(dev, "Error building cooling device %s %d\n", pd_name, ret); > >> + dev_pm_domain_detach(pd_dev, false); > >> + continue; > >> + } > > > > I am wondering about the use case of having multiple PM domains > > attached to the cooling (warming) device. Is that really needed? > > Perhaps you can elaborate on that a bit? > Ya. I though about this as well. I don't have a use case. In my current > case it is just one power domain on the SoC. But considering this is now > a generic driver, in my opinion this has to be a generic solution. So if > you think about this, the device should be able to specify any number of > power domains that can behave as a warming device since a SoC can have > any number of power domain based warming devices. May be one to warm up > the cpus, one for gpus etc. I get that, but you can always have more than one warming device. Each warming device would then be attached to a single PM domain. Or is there a problem with that? In any case, if you don't have use case for multiple PM domains per warming device at this point, I would rather keep it simple and start to support only the single PM domain case. > > So another way of implementing this whole thing is to avoid having a > special power domain warming device defined in the device tree. Instead, > add a few new binding to the power-domain controller/provider entries > to specify if a power domain controlled by the provider can act as a > warming device or not. And have the initialization code for the power > domain controller (of_genpd_add_provider_onecell or any other suitable > API) register the specified power domain as a warming device. The DT > entries should probably look something like below in the case. > > rpmhpd: power-controller { > compatible = "qcom,sdm845-rpmhpd"; > #power-domain-cells = <1>; > hosts-warming-dev; > warming-dev-names = "mx"; > operating-points-v2 = <&rpmhpd_opp_table>; > > rpmhpd_opp_table: opp-table { > compatible = "operating-points-v2"; > .... > > And have the following in of_genpd_add_provider_onecell > > if (hosts-warming-dev) > # loop through the warming-dev-names and register them as power domain > warming devices. > > You think this is a better idea? Not really, but you need to re-direct that question to DT maintainers if want a better answer. > > > > >> + } > >> + } else if (count == 1) { > >> + ret = of_property_read_string_index(dev->of_node, > >> + "power-domain-names", > >> + 0, &pd_name); > >> + if (ret) { > >> + dev_err(dev, "Error reading the power domain name %d\n", ret); > >> + goto exit; > >> + } > > > > According to my comment above, perhaps we simply don't have to use the > > "power-domain-names" binding at all. > I will use genpd->name > [...] Kind regards Uffe
On 09/13/2019 03:54 AM, Ulf Hansson wrote: > On Thu, 12 Sep 2019 at 22:18, Thara Gopinath <thara.gopinath@linaro.org> wrote: >> >> On 09/12/2019 11:04 AM, Ulf Hansson wrote: >> >> Hi Ulf, >> >> Thanks for the review. >>> On Tue, 10 Sep 2019 at 19:14, Thara Gopinath <thara.gopinath@linaro.org> wrote: >>>> >>>> Resources modeled as power domains in linux kenrel >>>> can be used to warm the SoC(eg. mx power domain on sdm845). >>>> To support this feature, introduce a generic power domain >>>> warming device driver that can be plugged into the thermal framework >>>> (The thermal framework itself requires further modifiction to >>>> support a warming device in place of a cooling device. >>>> Those extensions are not introduced in this patch series). >>>> >>>> Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org> >>>> --- >>>> v1->v2: >>>> - Make power domain based warming device driver a generic >>>> driver in the thermal framework. v1 implemented this as a >>>> Qualcomm specific driver. >>>> - Rename certain variables as per review suggestions on the >>>> mailing list. >>>> >>>> drivers/thermal/Kconfig | 11 +++ >>>> drivers/thermal/Makefile | 2 + >>>> drivers/thermal/pwr_domain_warming.c | 174 +++++++++++++++++++++++++++++++++++ >>>> 3 files changed, 187 insertions(+) >>>> create mode 100644 drivers/thermal/pwr_domain_warming.c >>>> >>>> diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig >>>> index 9966364..eeb6018 100644 >>>> --- a/drivers/thermal/Kconfig >>>> +++ b/drivers/thermal/Kconfig >>>> @@ -187,6 +187,17 @@ config DEVFREQ_THERMAL >>>> >>>> If you want this support, you should say Y here. >>>> >>>> +config PWR_DOMAIN_WARMING_THERMAL >>>> + bool "Power Domain based warming device" >>>> + depends on PM_GENERIC_DOMAINS >>>> + depends on PM_GENERIC_DOMAINS_OF >>> >>> PM_GENERIC_DOMAINS_OF can't be set unless PM_GENERIC_DOMAINS is set too. >>> >>> So I assume it's sufficient to depend on PM_GENERIC_DOMAINS_OF? >> >> Yes, you are right. I will change it. >>> >>>> + help >>>> + This implements the generic power domain based warming >>>> + mechanism through increasing the performance state of >>>> + a power domain. >>>> + >>>> + If you want this support, you should say Y here. >>>> + >>>> config THERMAL_EMULATION >>>> bool "Thermal emulation mode support" >>>> help >>>> diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile >>>> index 74a37c7..382c64a 100644 >>>> --- a/drivers/thermal/Makefile >>>> +++ b/drivers/thermal/Makefile >>>> @@ -27,6 +27,8 @@ thermal_sys-$(CONFIG_CLOCK_THERMAL) += clock_cooling.o >>>> # devfreq cooling >>>> thermal_sys-$(CONFIG_DEVFREQ_THERMAL) += devfreq_cooling.o >>>> >>>> +thermal_sys-$(CONFIG_PWR_DOMAIN_WARMING_THERMAL) += pwr_domain_warming.o >>>> + >>>> # platform thermal drivers >>>> obj-y += broadcom/ >>>> obj-$(CONFIG_THERMAL_MMIO) += thermal_mmio.o >>>> diff --git a/drivers/thermal/pwr_domain_warming.c b/drivers/thermal/pwr_domain_warming.c >>>> new file mode 100644 >>>> index 0000000..3dd792b >>>> --- /dev/null >>>> +++ b/drivers/thermal/pwr_domain_warming.c >>>> @@ -0,0 +1,174 @@ >>>> +// SPDX-License-Identifier: GPL-2.0 >>>> +/* >>>> + * Copyright (c) 2019, Linaro Ltd >>>> + */ >>>> +#include <linux/err.h> >>>> +#include <linux/kernel.h> >>>> +#include <linux/init.h> >>>> +#include <linux/of_device.h> >>>> +#include <linux/platform_device.h> >>>> +#include <linux/module.h> >>>> +#include <linux/pm_domain.h> >>>> +#include <linux/pm_runtime.h> >>>> +#include <linux/thermal.h> >>>> + >>>> +struct pd_warming_device { >>>> + struct thermal_cooling_device *cdev; >>>> + struct device *dev; >>>> + int max_state; >>>> + int cur_state; >>>> + bool runtime_resumed; >>>> +}; >>>> + >>>> +static const struct of_device_id pd_wdev_match_table[] = { >>>> + { .compatible = "thermal-power-domain-wdev", .data = NULL }, >>>> + { } >>>> +}; >>>> +MODULE_DEVICE_TABLE(of, pd_wdev_match_table); >>>> + >>>> +static int pd_wdev_get_max_state(struct thermal_cooling_device *cdev, >>>> + unsigned long *state) >>>> +{ >>>> + struct pd_warming_device *pd_wdev = cdev->devdata; >>>> + >>>> + *state = pd_wdev->max_state; >>>> + return 0; >>>> +} >>>> + >>>> +static int pd_wdev_get_cur_state(struct thermal_cooling_device *cdev, >>>> + unsigned long *state) >>>> +{ >>>> + struct pd_warming_device *pd_wdev = cdev->devdata; >>>> + >>>> + *state = dev_pm_genpd_get_performance_state(pd_wdev->dev); >>>> + >>>> + return 0; >>>> +} >>>> + >>>> +static int pd_wdev_set_cur_state(struct thermal_cooling_device *cdev, >>>> + unsigned long state) >>>> +{ >>>> + struct pd_warming_device *pd_wdev = cdev->devdata; >>>> + struct device *dev = pd_wdev->dev; >>>> + int ret; >>>> + >>>> + ret = dev_pm_genpd_set_performance_state(dev, state); >>>> + >>>> + if (ret) >>>> + return ret; >>>> + >>>> + if (state && !pd_wdev->runtime_resumed) { >>>> + ret = pm_runtime_get_sync(dev); >>>> + pd_wdev->runtime_resumed = true; >>>> + } else if (!state && pd_wdev->runtime_resumed) { >>>> + ret = pm_runtime_put(dev); >>>> + pd_wdev->runtime_resumed = false; >>>> + } >>>> + >>>> + return ret; >>>> +} >>>> + >>>> +static struct thermal_cooling_device_ops pd_warming_device_ops = { >>>> + .get_max_state = pd_wdev_get_max_state, >>>> + .get_cur_state = pd_wdev_get_cur_state, >>>> + .set_cur_state = pd_wdev_set_cur_state, >>>> +}; >>>> + >>>> +static int pd_wdev_create(struct device *dev, const char *name) >>>> +{ >>>> + struct pd_warming_device *pd_wdev; >>>> + int state_count; >>>> + >>>> + pd_wdev = devm_kzalloc(dev, sizeof(*pd_wdev), GFP_KERNEL); >>>> + if (!pd_wdev) >>>> + return -ENOMEM; >>>> + >>>> + state_count = dev_pm_genpd_performance_state_count(dev); >>>> + if (state_count < 0) >>>> + return state_count; >>>> + >>>> + pd_wdev->dev = dev; >>>> + pd_wdev->max_state = state_count - 1; >>>> + pd_wdev->runtime_resumed = false; >>>> + >>>> + pm_runtime_enable(dev); >>>> + >>>> + pd_wdev->cdev = thermal_of_cooling_device_register >>>> + (dev->of_node, name, >>>> + pd_wdev, >>>> + &pd_warming_device_ops); >>>> + if (IS_ERR(pd_wdev->cdev)) { >>>> + dev_err(dev, "unable to register %s cooling device\n", name); >>>> + pm_runtime_disable(dev); >>>> + >>>> + return PTR_ERR(pd_wdev->cdev); >>>> + } >>>> + >>>> + return 0; >>>> +} >>>> + >>>> +static int pd_wdev_probe(struct platform_device *pdev) >>>> +{ >>>> + struct device *dev = &pdev->dev, *pd_dev; >>>> + const char *pd_name; >>>> + int id, count, ret = 0; >>>> + >>>> + count = of_count_phandle_with_args(dev->of_node, "power-domains", >>>> + "#power-domain-cells"); >>> >>> Perhaps this should be converted to genpd OF helper function instead, >>> that allows the caller to know how many power-domains there are >>> specified for a device node. >> >> I am ok with this if you think that a OF helper to get the number of >> power domains is a useful helper in the genpd framework. I can add it as >> part of the next revision. Or do you want me to send it across separate? > > Feel free to include in the next version of the series. In case it's needed. Will do, if needed. (But as per below I am removing multiple PD support and hence this might not be needed) > >>> >>>> + >>>> + if (count > 1) { >>>> + for (id = 0; id < count; id++) { >>>> + ret = of_property_read_string_index >>>> + (dev->of_node, "power-domain-names", >>>> + id, &pd_name); >>>> + if (ret) { >>>> + dev_err(dev, "Error reading the power domain name %d\n", ret); >>>> + continue; >>>> + } >>> >>> It looks a bit awkward that you want to re-use the power-domain-names >>> as the name for the cooling (warming) device. This isn't really what >>> we use the "*-names" bindings for in general, I think. >>> >>> Anyway, if you want a name corresponding to the actual attached PM >>> domain, perhaps re-using "->name" from the struct generic_pm_domain is >>> better. We can add a genpd helper for that, no problem. Of course it >>> also means that you must call dev_pm_domain_attach_by_id() first, to >>> attach the device and then get the name of the genpd, but that should >>> be fine. >> >> Ya. I need a name corresponding to the power domain name (or something >> very close) to identify the actual warming device in the sysfs entries. >> I can use genpd->name and a helper function to achieve it. I can include >> it in Patch 1/5 where I add other helper functions. > > A separate patch please, but yeah, fold it in into @subject series. Sure! > >>> >>>> + >>>> + pd_dev = dev_pm_domain_attach_by_id(dev, id); >>>> + if (IS_ERR(pd_dev)) { >>>> + dev_err(dev, "Error attaching power domain %s %ld\n", pd_name, PTR_ERR(pd_dev)); >>>> + continue; >>>> + } >>>> + >>>> + ret = pd_wdev_create(pd_dev, pd_name); >>>> + if (ret) { >>>> + dev_err(dev, "Error building cooling device %s %d\n", pd_name, ret); >>>> + dev_pm_domain_detach(pd_dev, false); >>>> + continue; >>>> + } >>> >>> I am wondering about the use case of having multiple PM domains >>> attached to the cooling (warming) device. Is that really needed? >>> Perhaps you can elaborate on that a bit? >> Ya. I though about this as well. I don't have a use case. In my current >> case it is just one power domain on the SoC. But considering this is now >> a generic driver, in my opinion this has to be a generic solution. So if >> you think about this, the device should be able to specify any number of >> power domains that can behave as a warming device since a SoC can have >> any number of power domain based warming devices. May be one to warm up >> the cpus, one for gpus etc. > > I get that, but you can always have more than one warming device. Each > warming device would then be attached to a single PM domain. Or is > there a problem with that? > > In any case, if you don't have use case for multiple PM domains per > warming device at this point, I would rather keep it simple and start > to support only the single PM domain case. Ok. I will remove the support for multiple PM domains for now. > >> >> So another way of implementing this whole thing is to avoid having a >> special power domain warming device defined in the device tree. Instead, >> add a few new binding to the power-domain controller/provider entries >> to specify if a power domain controlled by the provider can act as a >> warming device or not. And have the initialization code for the power >> domain controller (of_genpd_add_provider_onecell or any other suitable >> API) register the specified power domain as a warming device. The DT >> entries should probably look something like below in the case. >> >> rpmhpd: power-controller { >> compatible = "qcom,sdm845-rpmhpd"; >> #power-domain-cells = <1>; >> hosts-warming-dev; >> warming-dev-names = "mx"; >> operating-points-v2 = <&rpmhpd_opp_table>; >> >> rpmhpd_opp_table: opp-table { >> compatible = "operating-points-v2"; >> .... >> >> And have the following in of_genpd_add_provider_onecell >> >> if (hosts-warming-dev) >> # loop through the warming-dev-names and register them as power domain >> warming devices. >> >> You think this is a better idea? > > Not really, but you need to re-direct that question to DT maintainers > if want a better answer. I will wait for the DT folks to take a look at this series. Hopefully DT folks will have some comments on the approach of a virtual device like this implementation vs specifying this info in the power domain controllers. I just wanted to run it by you to check whether you see any pros or cons from a genpd perspective. I will wait for a few more days for any additional review comments before sending v3 out.
diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig index 9966364..eeb6018 100644 --- a/drivers/thermal/Kconfig +++ b/drivers/thermal/Kconfig @@ -187,6 +187,17 @@ config DEVFREQ_THERMAL If you want this support, you should say Y here. +config PWR_DOMAIN_WARMING_THERMAL + bool "Power Domain based warming device" + depends on PM_GENERIC_DOMAINS + depends on PM_GENERIC_DOMAINS_OF + help + This implements the generic power domain based warming + mechanism through increasing the performance state of + a power domain. + + If you want this support, you should say Y here. + config THERMAL_EMULATION bool "Thermal emulation mode support" help diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile index 74a37c7..382c64a 100644 --- a/drivers/thermal/Makefile +++ b/drivers/thermal/Makefile @@ -27,6 +27,8 @@ thermal_sys-$(CONFIG_CLOCK_THERMAL) += clock_cooling.o # devfreq cooling thermal_sys-$(CONFIG_DEVFREQ_THERMAL) += devfreq_cooling.o +thermal_sys-$(CONFIG_PWR_DOMAIN_WARMING_THERMAL) += pwr_domain_warming.o + # platform thermal drivers obj-y += broadcom/ obj-$(CONFIG_THERMAL_MMIO) += thermal_mmio.o diff --git a/drivers/thermal/pwr_domain_warming.c b/drivers/thermal/pwr_domain_warming.c new file mode 100644 index 0000000..3dd792b --- /dev/null +++ b/drivers/thermal/pwr_domain_warming.c @@ -0,0 +1,174 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2019, Linaro Ltd + */ +#include <linux/err.h> +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/of_device.h> +#include <linux/platform_device.h> +#include <linux/module.h> +#include <linux/pm_domain.h> +#include <linux/pm_runtime.h> +#include <linux/thermal.h> + +struct pd_warming_device { + struct thermal_cooling_device *cdev; + struct device *dev; + int max_state; + int cur_state; + bool runtime_resumed; +}; + +static const struct of_device_id pd_wdev_match_table[] = { + { .compatible = "thermal-power-domain-wdev", .data = NULL }, + { } +}; +MODULE_DEVICE_TABLE(of, pd_wdev_match_table); + +static int pd_wdev_get_max_state(struct thermal_cooling_device *cdev, + unsigned long *state) +{ + struct pd_warming_device *pd_wdev = cdev->devdata; + + *state = pd_wdev->max_state; + return 0; +} + +static int pd_wdev_get_cur_state(struct thermal_cooling_device *cdev, + unsigned long *state) +{ + struct pd_warming_device *pd_wdev = cdev->devdata; + + *state = dev_pm_genpd_get_performance_state(pd_wdev->dev); + + return 0; +} + +static int pd_wdev_set_cur_state(struct thermal_cooling_device *cdev, + unsigned long state) +{ + struct pd_warming_device *pd_wdev = cdev->devdata; + struct device *dev = pd_wdev->dev; + int ret; + + ret = dev_pm_genpd_set_performance_state(dev, state); + + if (ret) + return ret; + + if (state && !pd_wdev->runtime_resumed) { + ret = pm_runtime_get_sync(dev); + pd_wdev->runtime_resumed = true; + } else if (!state && pd_wdev->runtime_resumed) { + ret = pm_runtime_put(dev); + pd_wdev->runtime_resumed = false; + } + + return ret; +} + +static struct thermal_cooling_device_ops pd_warming_device_ops = { + .get_max_state = pd_wdev_get_max_state, + .get_cur_state = pd_wdev_get_cur_state, + .set_cur_state = pd_wdev_set_cur_state, +}; + +static int pd_wdev_create(struct device *dev, const char *name) +{ + struct pd_warming_device *pd_wdev; + int state_count; + + pd_wdev = devm_kzalloc(dev, sizeof(*pd_wdev), GFP_KERNEL); + if (!pd_wdev) + return -ENOMEM; + + state_count = dev_pm_genpd_performance_state_count(dev); + if (state_count < 0) + return state_count; + + pd_wdev->dev = dev; + pd_wdev->max_state = state_count - 1; + pd_wdev->runtime_resumed = false; + + pm_runtime_enable(dev); + + pd_wdev->cdev = thermal_of_cooling_device_register + (dev->of_node, name, + pd_wdev, + &pd_warming_device_ops); + if (IS_ERR(pd_wdev->cdev)) { + dev_err(dev, "unable to register %s cooling device\n", name); + pm_runtime_disable(dev); + + return PTR_ERR(pd_wdev->cdev); + } + + return 0; +} + +static int pd_wdev_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev, *pd_dev; + const char *pd_name; + int id, count, ret = 0; + + count = of_count_phandle_with_args(dev->of_node, "power-domains", + "#power-domain-cells"); + + if (count > 1) { + for (id = 0; id < count; id++) { + ret = of_property_read_string_index + (dev->of_node, "power-domain-names", + id, &pd_name); + if (ret) { + dev_err(dev, "Error reading the power domain name %d\n", ret); + continue; + } + + pd_dev = dev_pm_domain_attach_by_id(dev, id); + if (IS_ERR(pd_dev)) { + dev_err(dev, "Error attaching power domain %s %ld\n", pd_name, PTR_ERR(pd_dev)); + continue; + } + + ret = pd_wdev_create(pd_dev, pd_name); + if (ret) { + dev_err(dev, "Error building cooling device %s %d\n", pd_name, ret); + dev_pm_domain_detach(pd_dev, false); + continue; + } + } + } else if (count == 1) { + ret = of_property_read_string_index(dev->of_node, + "power-domain-names", + 0, &pd_name); + if (ret) { + dev_err(dev, "Error reading the power domain name %d\n", ret); + goto exit; + } + + ret = pd_wdev_create(dev, pd_name); + if (ret) { + dev_err(dev, "Error building cooling device %s %d\n", pd_name, ret); + goto exit; + } + } else { + ret = -EINVAL; + } + +exit: + return ret; +} + +static struct platform_driver pd_wdev_driver = { + .driver = { + .name = "qcom-rpmhpd-cdev", + .of_match_table = pd_wdev_match_table, + }, + .probe = pd_wdev_probe, +}; +module_platform_driver(pd_wdev_driver); + +MODULE_DESCRIPTION("Qualcomm RPMHPD cooling device driver"); +MODULE_LICENSE("GPL v2");
Resources modeled as power domains in linux kenrel can be used to warm the SoC(eg. mx power domain on sdm845). To support this feature, introduce a generic power domain warming device driver that can be plugged into the thermal framework (The thermal framework itself requires further modifiction to support a warming device in place of a cooling device. Those extensions are not introduced in this patch series). Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org> --- v1->v2: - Make power domain based warming device driver a generic driver in the thermal framework. v1 implemented this as a Qualcomm specific driver. - Rename certain variables as per review suggestions on the mailing list. drivers/thermal/Kconfig | 11 +++ drivers/thermal/Makefile | 2 + drivers/thermal/pwr_domain_warming.c | 174 +++++++++++++++++++++++++++++++++++ 3 files changed, 187 insertions(+) create mode 100644 drivers/thermal/pwr_domain_warming.c