@@ -765,6 +765,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \
am335x-wega-rdk.dtb \
am335x-osd3358-sm-red.dtb
dtb-$(CONFIG_ARCH_OMAP4) += \
+ omap4-droid-bionic-xt875.dtb \
omap4-droid4-xt894.dtb \
omap4-duovero-parlor.dtb \
omap4-kc1.dtb \
similarity index 99%
copy from arch/arm/boot/dts/omap4-droid4-xt894.dts
copy to arch/arm/boot/dts/motorola-mapphone-common.dtsi
@@ -6,9 +6,6 @@
#include "motorola-cpcap-mapphone.dtsi"
/ {
- model = "Motorola Droid 4 XT894";
- compatible = "motorola,droid4", "ti,omap4430", "ti,omap4";
-
chosen {
stdout-path = &uart3;
};
new file mode 100644
@@ -0,0 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/dts-v1/;
+
+#include "motorola-mapphone-common.dtsi"
+
+/ {
+ model = "Motorola Droid Bionic XT875";
+ compatible = "motorola,droid-bionic", "ti,omap4430", "ti,omap4";
+};
@@ -1,784 +1,9 @@
// SPDX-License-Identifier: GPL-2.0-only
/dts-v1/;
-#include <dt-bindings/input/input.h>
-#include "omap443x.dtsi"
-#include "motorola-cpcap-mapphone.dtsi"
+#include "motorola-mapphone-common.dtsi"
/ {
model = "Motorola Droid 4 XT894";
compatible = "motorola,droid4", "ti,omap4430", "ti,omap4";
-
- chosen {
- stdout-path = &uart3;
- };
-
- aliases {
- display0 = &lcd0;
- display1 = &hdmi0;
- };
-
- /*
- * We seem to have only 1021 MB accessible, 1021 - 1022 is locked,
- * then 1023 - 1024 seems to contain mbm.
- */
- memory {
- device_type = "memory";
- reg = <0x80000000 0x3fd00000>; /* 1021 MB */
- };
-
- /* Poweroff GPIO probably connected to CPCAP */
- gpio-poweroff {
- compatible = "gpio-poweroff";
- pinctrl-0 = <&poweroff_gpio>;
- pinctrl-names = "default";
- gpios = <&gpio2 18 GPIO_ACTIVE_LOW>; /* gpio50 */
- };
-
- hdmi0: connector {
- compatible = "hdmi-connector";
- pinctrl-0 = <&hdmi_hpd_gpio>;
- pinctrl-names = "default";
- label = "hdmi";
- type = "d";
-
- hpd-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>; /* gpio63 */
-
- port {
- hdmi_connector_in: endpoint {
- remote-endpoint = <&hdmi_out>;
- };
- };
- };
-
- /*
- * HDMI 5V regulator probably sourced from battery. Let's keep
- * keep this as always enabled for HDMI to work until we've
- * figured what the encoder chip is.
- */
- hdmi_regulator: regulator-hdmi {
- compatible = "regulator-fixed";
- regulator-name = "hdmi";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio2 27 GPIO_ACTIVE_HIGH>; /* gpio59 */
- enable-active-high;
- regulator-always-on;
- };
-
- /* FS USB Host PHY on port 1 for mdm6600 */
- fsusb1_phy: usb-phy@1 {
- compatible = "motorola,mapphone-mdm6600";
- pinctrl-0 = <&usb_mdm6600_pins>;
- pinctrl-names = "default";
- enable-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>; /* gpio_95 */
- power-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>; /* gpio_54 */
- reset-gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>; /* gpio_49 */
- /* mode: gpio_148 gpio_149 */
- motorola,mode-gpios = <&gpio5 20 GPIO_ACTIVE_HIGH>,
- <&gpio5 21 GPIO_ACTIVE_HIGH>;
- /* cmd: gpio_103 gpio_104 gpio_142 */
- motorola,cmd-gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>,
- <&gpio4 8 GPIO_ACTIVE_HIGH>,
- <&gpio5 14 GPIO_ACTIVE_HIGH>;
- /* status: gpio_52 gpio_53 gpio_55 */
- motorola,status-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>,
- <&gpio2 21 GPIO_ACTIVE_HIGH>,
- <&gpio2 23 GPIO_ACTIVE_HIGH>;
- #phy-cells = <0>;
- };
-
- /* HS USB host TLL nop-phy on port 2 for w3glte */
- hsusb2_phy: usb-phy@2 {
- compatible = "usb-nop-xceiv";
- #phy-cells = <0>;
- };
-
- /* LCD regulator from sw5 source */
- lcd_regulator: regulator-lcd {
- compatible = "regulator-fixed";
- regulator-name = "lcd";
- regulator-min-microvolt = <5050000>;
- regulator-max-microvolt = <5050000>;
- gpio = <&gpio4 0 GPIO_ACTIVE_HIGH>; /* gpio96 */
- enable-active-high;
- vin-supply = <&sw5>;
- };
-
- /* This is probably coming straight from the battery.. */
- wl12xx_vmmc: regulator-wl12xx {
- compatible = "regulator-fixed";
- regulator-name = "vwl1271";
- regulator-min-microvolt = <1650000>;
- regulator-max-microvolt = <1650000>;
- gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>; /* gpio94 */
- startup-delay-us = <70000>;
- enable-active-high;
- };
-
- gpio_keys {
- compatible = "gpio-keys";
-
- volume_down {
- label = "Volume Down";
- gpios = <&gpio5 26 GPIO_ACTIVE_LOW>; /* gpio154 */
- linux,code = <KEY_VOLUMEDOWN>;
- linux,can-disable;
- /* Value above 7.95ms for no GPIO hardware debounce */
- debounce-interval = <10>;
- };
-
- slider {
- label = "Keypad Slide";
- gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>; /* gpio122 */
- linux,input-type = <EV_SW>;
- linux,code = <SW_KEYPAD_SLIDE>;
- linux,can-disable;
- /* Value above 7.95ms for no GPIO hardware debounce */
- debounce-interval = <10>;
- };
- };
-
- soundcard {
- compatible = "audio-graph-card";
- label = "Droid 4 Audio";
-
- simple-graph-card,widgets =
- "Speaker", "Earpiece",
- "Speaker", "Loudspeaker",
- "Headphone", "Headphone Jack",
- "Microphone", "Internal Mic";
-
- simple-graph-card,routing =
- "Earpiece", "EP",
- "Loudspeaker", "SPKR",
- "Headphone Jack", "HSL",
- "Headphone Jack", "HSR",
- "MICR", "Internal Mic";
-
- dais = <&mcbsp2_port>, <&mcbsp3_port>;
- };
-
- pwm8: dmtimer-pwm-8 {
- pinctrl-names = "default";
- pinctrl-0 = <&vibrator_direction_pin>;
-
- compatible = "ti,omap-dmtimer-pwm";
- #pwm-cells = <3>;
- ti,timers = <&timer8>;
- ti,clock-source = <0x01>;
- };
-
- pwm9: dmtimer-pwm-9 {
- pinctrl-names = "default";
- pinctrl-0 = <&vibrator_enable_pin>;
-
- compatible = "ti,omap-dmtimer-pwm";
- #pwm-cells = <3>;
- ti,timers = <&timer9>;
- ti,clock-source = <0x01>;
- };
-
- vibrator {
- compatible = "pwm-vibrator";
- pwms = <&pwm9 0 10000000 0>, <&pwm8 0 10000000 0>;
- pwm-names = "enable", "direction";
- direction-duty-cycle-ns = <10000000>;
- };
-};
-
-&dss {
- status = "okay";
-};
-
-&dsi1 {
- status = "okay";
- vdd-supply = <&vcsi>;
-
- port {
- dsi1_out_ep: endpoint {
- remote-endpoint = <&lcd0_in>;
- lanes = <0 1 2 3 4 5>;
- };
- };
-
- lcd0: display {
- compatible = "panel-dsi-cm";
- label = "lcd0";
- vddi-supply = <&lcd_regulator>;
- reset-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>; /* gpio101 */
-
- width-mm = <50>;
- height-mm = <89>;
-
- panel-timing {
- clock-frequency = <0>; /* Calculated by dsi */
-
- hback-porch = <2>;
- hactive = <540>;
- hfront-porch = <0>;
- hsync-len = <2>;
-
- vback-porch = <1>;
- vactive = <960>;
- vfront-porch = <0>;
- vsync-len = <1>;
-
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
-
- port {
- lcd0_in: endpoint {
- remote-endpoint = <&dsi1_out_ep>;
- };
- };
- };
-};
-
-&hdmi {
- status = "okay";
- pinctrl-0 = <&dss_hdmi_pins>;
- pinctrl-names = "default";
- vdda-supply = <&vdac>;
-
- port {
- hdmi_out: endpoint {
- remote-endpoint = <&hdmi_connector_in>;
- lanes = <1 0 3 2 5 4 7 6>;
- };
- };
-};
-
-&i2c1 {
- tmp105@48 {
- compatible = "ti,tmp105";
- reg = <0x48>;
- pinctrl-0 = <&tmp105_irq>;
- pinctrl-names = "default";
- /* kpd_row0.gpio_178 */
- interrupts-extended = <&gpio6 18 IRQ_TYPE_EDGE_FALLING
- &omap4_pmx_core 0x14e>;
- interrupt-names = "irq", "wakeup";
- wakeup-source;
- };
-};
-
-&keypad {
- keypad,num-rows = <8>;
- keypad,num-columns = <8>;
- linux,keymap = <
-
- /* Row 1 */
- MATRIX_KEY(0, 2, KEY_1)
- MATRIX_KEY(0, 6, KEY_2)
- MATRIX_KEY(2, 3, KEY_3)
- MATRIX_KEY(0, 7, KEY_4)
- MATRIX_KEY(0, 4, KEY_5)
- MATRIX_KEY(5, 5, KEY_6)
- MATRIX_KEY(0, 1, KEY_7)
- MATRIX_KEY(0, 5, KEY_8)
- MATRIX_KEY(0, 0, KEY_9)
- MATRIX_KEY(1, 6, KEY_0)
-
- /* Row 2 */
- MATRIX_KEY(3, 4, KEY_APOSTROPHE)
- MATRIX_KEY(7, 6, KEY_Q)
- MATRIX_KEY(7, 7, KEY_W)
- MATRIX_KEY(7, 2, KEY_E)
- MATRIX_KEY(1, 0, KEY_R)
- MATRIX_KEY(4, 4, KEY_T)
- MATRIX_KEY(1, 2, KEY_Y)
- MATRIX_KEY(6, 7, KEY_U)
- MATRIX_KEY(2, 2, KEY_I)
- MATRIX_KEY(5, 6, KEY_O)
- MATRIX_KEY(3, 7, KEY_P)
- MATRIX_KEY(6, 5, KEY_BACKSPACE)
-
- /* Row 3 */
- MATRIX_KEY(5, 4, KEY_TAB)
- MATRIX_KEY(5, 7, KEY_A)
- MATRIX_KEY(2, 7, KEY_S)
- MATRIX_KEY(7, 0, KEY_D)
- MATRIX_KEY(2, 6, KEY_F)
- MATRIX_KEY(6, 2, KEY_G)
- MATRIX_KEY(6, 6, KEY_H)
- MATRIX_KEY(1, 4, KEY_J)
- MATRIX_KEY(3, 1, KEY_K)
- MATRIX_KEY(2, 1, KEY_L)
- MATRIX_KEY(4, 6, KEY_ENTER)
-
- /* Row 4 */
- MATRIX_KEY(3, 6, KEY_LEFTSHIFT) /* KEY_CAPSLOCK */
- MATRIX_KEY(6, 1, KEY_Z)
- MATRIX_KEY(7, 4, KEY_X)
- MATRIX_KEY(5, 1, KEY_C)
- MATRIX_KEY(1, 7, KEY_V)
- MATRIX_KEY(2, 4, KEY_B)
- MATRIX_KEY(4, 1, KEY_N)
- MATRIX_KEY(1, 1, KEY_M)
- MATRIX_KEY(3, 5, KEY_COMMA)
- MATRIX_KEY(5, 2, KEY_DOT)
- MATRIX_KEY(6, 3, KEY_UP)
- MATRIX_KEY(7, 3, KEY_OK)
-
- /* Row 5 */
- MATRIX_KEY(2, 5, KEY_LEFTCTRL) /* KEY_LEFTSHIFT */
- MATRIX_KEY(4, 5, KEY_LEFTALT) /* SYM */
- MATRIX_KEY(6, 0, KEY_MINUS)
- MATRIX_KEY(4, 7, KEY_EQUAL)
- MATRIX_KEY(1, 5, KEY_SPACE)
- MATRIX_KEY(3, 2, KEY_SLASH)
- MATRIX_KEY(4, 3, KEY_LEFT)
- MATRIX_KEY(5, 3, KEY_DOWN)
- MATRIX_KEY(3, 3, KEY_RIGHT)
-
- /* Side buttons, KEY_VOLUMEDOWN and KEY_PWER are on CPCAP? */
- MATRIX_KEY(5, 0, KEY_VOLUMEUP)
- >;
-};
-
-&mmc1 {
- vmmc-supply = <&vwlan2>;
- bus-width = <4>;
- cd-gpios = <&gpio6 16 GPIO_ACTIVE_LOW>; /* gpio176 */
-};
-
-&mmc2 {
- vmmc-supply = <&vsdio>;
- bus-width = <8>;
- ti,non-removable;
-};
-
-&mmc3 {
- vmmc-supply = <&wl12xx_vmmc>;
- /* uart2_tx.sdmmc3_dat1 pad as wakeirq */
- interrupts-extended = <&wakeupgen GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH
- &omap4_pmx_core 0xde>;
- interrupt-names = "irq", "wakeup";
- non-removable;
- bus-width = <4>;
- cap-power-off-card;
- keep-power-in-suspend;
-
- #address-cells = <1>;
- #size-cells = <0>;
- wlcore: wlcore@2 {
- compatible = "ti,wl1285", "ti,wl1283";
- reg = <2>;
- /* gpio_100 with gpmc_wait2 pad as wakeirq */
- interrupts-extended = <&gpio4 4 IRQ_TYPE_EDGE_RISING>,
- <&omap4_pmx_core 0x4e>;
- interrupt-names = "irq", "wakeup";
- ref-clock-frequency = <26000000>;
- tcxo-clock-frequency = <26000000>;
- };
-};
-
-&i2c1 {
- led-controller@38 {
- compatible = "ti,lm3532";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x38>;
-
- enable-gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
-
- ramp-up-us = <1024>;
- ramp-down-us = <8193>;
-
- led@0 {
- reg = <0>;
- led-sources = <2>;
- ti,led-mode = <0>;
- label = ":backlight";
- linux,default-trigger = "backlight";
- };
-
- led@1 {
- reg = <1>;
- led-sources = <1>;
- ti,led-mode = <0>;
- label = ":kbd_backlight";
- };
- };
-};
-
-&i2c2 {
- touchscreen@4a {
- compatible = "atmel,maxtouch";
- reg = <0x4a>;
- pinctrl-names = "default";
- pinctrl-0 = <&touchscreen_pins>;
-
- reset-gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>; /* gpio173 */
-
- /* gpio_183 with sys_nirq2 pad as wakeup */
- interrupts-extended = <&gpio6 23 IRQ_TYPE_EDGE_FALLING>,
- <&omap4_pmx_core 0x160>;
- interrupt-names = "irq", "wakeup";
- wakeup-source;
- };
-
- isl29030@44 {
- compatible = "isil,isl29030";
- reg = <0x44>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&als_proximity_pins>;
-
- interrupt-parent = <&gpio6>;
- interrupts = <17 IRQ_TYPE_LEVEL_LOW>; /* gpio177 */
- };
-};
-
-&omap4_pmx_core {
-
- /* hdmi_hpd.gpio_63 */
- hdmi_hpd_gpio: pinmux_hdmi_hpd_pins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x098, PIN_INPUT | MUX_MODE3)
- >;
- };
-
- /* hdmi_cec.hdmi_cec, hdmi_scl.hdmi_scl, hdmi_sda.hdmi_sda */
- dss_hdmi_pins: pinmux_dss_hdmi_pins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0)
- OMAP4_IOPAD(0x09c, PIN_INPUT | MUX_MODE0)
- OMAP4_IOPAD(0x09e, PIN_INPUT | MUX_MODE0)
- >;
- };
-
- /* gpmc_ncs0.gpio_50 */
- poweroff_gpio: pinmux_poweroff_pins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x074, PIN_OUTPUT_PULLUP | MUX_MODE3)
- >;
- };
-
- /* kpd_row0.gpio_178 */
- tmp105_irq: pinmux_tmp105_irq {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x18e, PIN_INPUT_PULLUP | MUX_MODE3)
- >;
- };
-
- usb_gpio_mux_sel1: pinmux_usb_gpio_mux_sel1_pins {
- /* gpio_60 */
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x088, PIN_OUTPUT | MUX_MODE3)
- >;
- };
-
- touchscreen_pins: pinmux_touchscreen_pins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x180, PIN_OUTPUT | MUX_MODE3)
- OMAP4_IOPAD(0x1a0, PIN_INPUT_PULLUP | MUX_MODE3)
- >;
- };
-
- als_proximity_pins: pinmux_als_proximity_pins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x18c, PIN_INPUT_PULLUP | MUX_MODE3)
- >;
- };
-
- usb_mdm6600_pins: pinmux_usb_mdm6600_pins {
- pinctrl-single,pins = <
- /* enable 0x4a1000d8 usbb1_ulpitll_dat7.gpio_95 ag16 */
- OMAP4_IOPAD(0x0d8, PIN_INPUT | MUX_MODE3)
-
- /* power 0x4a10007c gpmc_nwp.gpio_54 c25 */
- OMAP4_IOPAD(0x07c, PIN_OUTPUT | MUX_MODE3)
-
- /* reset 0x4a100072 gpmc_a25.gpio_49 d20 */
- OMAP4_IOPAD(0x072, PIN_OUTPUT | MUX_MODE3)
-
- /* mode0/bpwake 0x4a10014e sdmmc5_dat1.gpio_148 af4 */
- OMAP4_IOPAD(0x14e, PIN_OUTPUT | MUX_MODE3)
-
- /* mode1/apwake 0x4a100150 sdmmc5_dat2.gpio_149 ag3 */
- OMAP4_IOPAD(0x150, PIN_OFF_OUTPUT_LOW | PIN_INPUT | MUX_MODE3)
-
- /* status0 0x4a10007e gpmc_clk.gpio_55 b22 */
- OMAP4_IOPAD(0x07e, PIN_INPUT | MUX_MODE3)
-
- /* status1 0x4a10007a gpmc_ncs3.gpio_53 c22 */
- OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3)
-
- /* status2 0x4a100078 gpmc_ncs2.gpio_52 d21 */
- OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3)
-
- /* cmd0 0x4a100094 gpmc_ncs6.gpio_103 c24 */
- OMAP4_IOPAD(0x094, PIN_OUTPUT | MUX_MODE3)
-
- /* cmd1 0x4a100096 gpmc_ncs7.gpio_104 d24 */
- OMAP4_IOPAD(0x096, PIN_OUTPUT | MUX_MODE3)
-
- /* cmd2 0x4a100142 uart3_rts_sd.gpio_142 f28 */
- OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE3)
- >;
- };
-
- usb_ulpi_pins: pinmux_usb_ulpi_pins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x196, MUX_MODE7)
- OMAP4_IOPAD(0x198, MUX_MODE7)
- OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE0)
- OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE0)
- OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE0)
- OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE0)
- OMAP4_IOPAD(0x1ba, PIN_INPUT_PULLUP | MUX_MODE0)
- OMAP4_IOPAD(0x1bc, PIN_INPUT_PULLUP | MUX_MODE0)
- OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE0)
- OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE0)
- OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE0)
- OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE0)
- OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE0)
- OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE0)
- >;
- };
-
- /* usb0_otg_dp and usb0_otg_dm */
- usb_utmi_pins: pinmux_usb_utmi_pins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x196, PIN_INPUT | MUX_MODE0)
- OMAP4_IOPAD(0x198, PIN_INPUT | MUX_MODE0)
- OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE7)
- OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE7)
- OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE7)
- OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE7)
- OMAP4_IOPAD(0x1ba, PIN_INPUT_PULLUP | MUX_MODE7)
- OMAP4_IOPAD(0x1bc, PIN_INPUT_PULLUP | MUX_MODE7)
- OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE7)
- OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE7)
- OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE7)
- OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE7)
- OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE7)
- OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE7)
- >;
- };
-
- /*
- * Note that the v3.0.8 stock userspace dynamically remuxes uart1
- * rts pin probably for PM purposes to PIN_INPUT_PULLUP | MUX_MODE7
- * when not used. If needed, we can add rts pin remux later based
- * on power measurements.
- */
- uart1_pins: pinmux_uart1_pins {
- pinctrl-single,pins = <
- /* 0x4a10013c mcspi1_cs2.uart1_cts ag23 */
- OMAP4_IOPAD(0x13c, PIN_INPUT_PULLUP | MUX_MODE1)
-
- /* 0x4a10013e mcspi1_cs3.uart1_rts ah23 */
- OMAP4_IOPAD(0x13e, MUX_MODE1)
-
- /* 0x4a100140 uart3_cts_rctx.uart1_tx f27 */
- OMAP4_IOPAD(0x140, PIN_OUTPUT | MUX_MODE1)
-
- /* 0x4a1001ca dpm_emu14.uart1_rx aa3 */
- OMAP4_IOPAD(0x1ca, PIN_INPUT_PULLUP | MUX_MODE2)
- >;
- };
-
- /* uart3_tx_irtx and uart3_rx_irrx */
- uart3_pins: pinmux_uart3_pins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x196, MUX_MODE7)
- OMAP4_IOPAD(0x198, MUX_MODE7)
- OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE7)
- OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE7)
- OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE7)
- OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE7)
- OMAP4_IOPAD(0x1ba, MUX_MODE2)
- OMAP4_IOPAD(0x1bc, PIN_INPUT | MUX_MODE2)
- OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE7)
- OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE7)
- OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE7)
- OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE7)
- OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE7)
- OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE7)
- >;
- };
-
- uart4_pins: pinmux_uart4_pins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x15c, PIN_INPUT | MUX_MODE0) /* uart4_rx */
- OMAP4_IOPAD(0x15e, PIN_OUTPUT | MUX_MODE0) /* uart4_tx */
- OMAP4_IOPAD(0x110, PIN_INPUT_PULLUP | MUX_MODE5) /* uart4_cts */
- OMAP4_IOPAD(0x112, PIN_OUTPUT_PULLUP | MUX_MODE5) /* uart4_rts */
- >;
- };
-
- mcbsp2_pins: pinmux_mcbsp2_pins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x0f6, PIN_INPUT | MUX_MODE0) /* abe_mcbsp2_clkx */
- OMAP4_IOPAD(0x0f8, PIN_INPUT | MUX_MODE0) /* abe_mcbsp2_dr */
- OMAP4_IOPAD(0x0fa, PIN_OUTPUT | MUX_MODE0) /* abe_mcbsp2_dx */
- OMAP4_IOPAD(0x0fc, PIN_INPUT | MUX_MODE0) /* abe_mcbsp2_fsx */
- >;
- };
-
- mcbsp3_pins: pinmux_mcbsp3_pins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x106, PIN_INPUT | MUX_MODE1) /* abe_mcbsp3_dr */
- OMAP4_IOPAD(0x108, PIN_OUTPUT | MUX_MODE1) /* abe_mcbsp3_dx */
- OMAP4_IOPAD(0x10a, PIN_INPUT | MUX_MODE1) /* abe_mcbsp3_clkx */
- OMAP4_IOPAD(0x10c, PIN_INPUT | MUX_MODE1) /* abe_mcbsp3_fsx */
- >;
- };
-
- vibrator_direction_pin: pinmux_vibrator_direction_pin {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x1ce, PIN_OUTPUT | MUX_MODE1) /* dmtimer8_pwm_evt (gpio_27) */
- >;
- };
-
- vibrator_enable_pin: pinmux_vibrator_enable_pin {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0X1d0, PIN_OUTPUT | MUX_MODE1) /* dmtimer9_pwm_evt (gpio_28) */
- >;
- };
-};
-
-&omap4_pmx_wkup {
- usb_gpio_mux_sel2: pinmux_usb_gpio_mux_sel2_pins {
- /* gpio_wk0 */
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x040, PIN_OUTPUT_PULLDOWN | MUX_MODE3)
- >;
- };
-};
-
-/* Configure pwm clock source for timers 8 & 9 */
-&timer8 {
- assigned-clocks = <&abe_clkctrl OMAP4_TIMER8_CLKCTRL 24>;
- assigned-clock-parents = <&sys_clkin_ck>;
-};
-
-&timer9 {
- assigned-clocks = <&l4_per_clkctrl OMAP4_TIMER9_CLKCTRL 24>;
- assigned-clock-parents = <&sys_clkin_ck>;
-};
-
-/*
- * As uart1 is wired to mdm6600 with rts and cts, we can use the cts pin for
- * uart1 wakeirq.
- */
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins>;
- interrupts-extended = <&wakeupgen GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH
- &omap4_pmx_core 0xfc>;
-};
-
-&uart3 {
- interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH
- &omap4_pmx_core 0x17c>;
-};
-
-&uart4 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart4_pins>;
-
- bluetooth {
- compatible = "ti,wl1285-st";
- enable-gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>; /* gpio 174 */
- max-speed = <3686400>;
- };
-};
-
-&usbhsohci {
- phys = <&fsusb1_phy>;
- phy-names = "usb";
-};
-
-&usbhsehci {
- phys = <&hsusb2_phy>;
-};
-
-&usbhshost {
- port1-mode = "ohci-phy-4pin-dpdm";
- port2-mode = "ehci-tll";
-};
-
-/* Internal UTMI+ PHY used for OTG, CPCAP ULPI PHY for detection and charger */
-&usb_otg_hs {
- interface-type = <1>;
- mode = <3>;
- power = <50>;
-};
-
-&i2c4 {
- ak8975: magnetometer@c {
- compatible = "asahi-kasei,ak8975";
- reg = <0x0c>;
-
- vdd-supply = <&vhvio>;
-
- interrupt-parent = <&gpio6>;
- interrupts = <15 IRQ_TYPE_EDGE_RISING>; /* gpio175 */
-
- rotation-matrix = "-1", "0", "0",
- "0", "1", "0",
- "0", "0", "-1";
-
- };
-
- lis3dh: accelerometer@18 {
- compatible = "st,lis3dh-accel";
- reg = <0x18>;
-
- vdd-supply = <&vhvio>;
-
- interrupt-parent = <&gpio2>;
- interrupts = <2 IRQ_TYPE_EDGE_BOTH>; /* gpio34 */
-
- rotation-matrix = "0", "-1", "0",
- "1", "0", "0",
- "0", "0", "1";
- };
-};
-
-&mcbsp2 {
- #sound-dai-cells = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&mcbsp2_pins>;
- status = "okay";
-
- mcbsp2_port: port {
- cpu_dai2: endpoint {
- dai-format = "i2s";
- remote-endpoint = <&cpcap_audio_codec0>;
- frame-master = <&cpcap_audio_codec0>;
- bitclock-master = <&cpcap_audio_codec0>;
- };
- };
-};
-
-&mcbsp3 {
- #sound-dai-cells = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&mcbsp3_pins>;
- status = "okay";
-
- mcbsp3_port: port {
- cpu_dai3: endpoint {
- dai-format = "dsp_a";
- frame-master = <&cpcap_audio_codec1>;
- bitclock-master = <&cpcap_audio_codec1>;
- remote-endpoint = <&cpcap_audio_codec1>;
- };
- };
-};
-
-&cpcap_audio_codec0 {
- remote-endpoint = <&cpu_dai2>;
-};
-
-&cpcap_audio_codec1 {
- remote-endpoint = <&cpu_dai3>;
};
We already have folks booting Droid Bionic with Droid 4 dts, but it is a different hardware with no keyboard. Let's start adding device specific support for Droid bionic by making current omap4-droid4-xt894 a common file and including it. Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Cc: Sebastian Reichel <sre@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com>