| Message ID | 20191108015702.233102-9-damien.lemoal@wdc.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Zoned block device enhancements and zone report rework | expand |
Looks good,
Reviewed-by: Christoph Hellwig <hch@lst.de>
On 11/8/19 2:57 AM, Damien Le Moal wrote: > There is no need to arbitrarily limit the size of a report zone to the > number of zones defined by SD_ZBC_REPORT_MAX_ZONES. Rather, simply > calculate the report buffer size needed for the requested number of > zones without exceeding the device total number of zones. This buffer > size limitation to the hardware maximum transfer size and page mapping > capabilities is kept unchanged. Starting with this initial buffer size, > the allocation is optimized by iterating over decreasing buffer size > until the allocation succeeds. This ensures forward progress for zone > reports and avoids failures of zones revalidation under memory pressure. > > While at it, also replace the hard coded 512 B sector size with the > SECTOR_SIZE macro. > > Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> > --- > drivers/scsi/sd_zbc.c | 22 +++++++++++----------- > 1 file changed, 11 insertions(+), 11 deletions(-) > Reviewed-by: Hannes Reinecke <hare@suse.de> Cheers, Hannes
On 11/7/19 5:57 PM, Damien Le Moal wrote: > - buf = vzalloc(bufsize); > - if (buf) > - *buflen = bufsize; > + while (bufsize >= SECTOR_SIZE) { > + buf = vzalloc(bufsize); > + if (buf) { > + *buflen = bufsize; > + return buf; > + } > + bufsize >>= 1; > + } Hi Damien, Has it been considered to pass the __GFP_NORETRY flag to this vzalloc() call? Thanks, Bart.
On 2019/11/09 4:06, Bart Van Assche wrote: > On 11/7/19 5:57 PM, Damien Le Moal wrote: >> - buf = vzalloc(bufsize); >> - if (buf) >> - *buflen = bufsize; >> + while (bufsize >= SECTOR_SIZE) { >> + buf = vzalloc(bufsize); >> + if (buf) { >> + *buflen = bufsize; >> + return buf; >> + } >> + bufsize >>= 1; >> + } > > Hi Damien, > > Has it been considered to pass the __GFP_NORETRY flag to this vzalloc() > call? Do you mean using __vmalloc(bufsize, GFP_KERNEL | __GFP_ZERO | __GFP_NORETRY, PAGE_KERNEL); instead of vzalloc() ? (since we cannot pass GFP flags to vzalloc()...) Note that this is called with GFP_NOIO set for the caller context in the case of revalidate zones, and default to GFP_KERNEL for blkdev_report_zones() unless the caller also tweaks the context memalloc flags. > > Thanks, > > Bart. >
On 2019-11-08 18:54, Damien Le Moal wrote: > On 2019/11/09 4:06, Bart Van Assche wrote: >> On 11/7/19 5:57 PM, Damien Le Moal wrote: >>> - buf = vzalloc(bufsize); >>> - if (buf) >>> - *buflen = bufsize; >>> + while (bufsize >= SECTOR_SIZE) { >>> + buf = vzalloc(bufsize); >>> + if (buf) { >>> + *buflen = bufsize; >>> + return buf; >>> + } >>> + bufsize >>= 1; >>> + } >> >> Hi Damien, >> >> Has it been considered to pass the __GFP_NORETRY flag to this vzalloc() >> call? > > Do you mean using > > __vmalloc(bufsize, > GFP_KERNEL | __GFP_ZERO | __GFP_NORETRY, PAGE_KERNEL); > > instead of vzalloc() ? (since we cannot pass GFP flags to vzalloc()...) > > Note that this is called with GFP_NOIO set for the caller context in the > case of revalidate zones, and default to GFP_KERNEL for > blkdev_report_zones() unless the caller also tweaks the context memalloc > flags. Hi Damien, Yes, that's what I meant. The following comment from mm/util.c explains why __GFP_RETRY should be used if it is OK for an allocation to fail: /* * We want to attempt a large physically contiguous block first because * it is less likely to fragment multiple larger blocks and therefore * contribute to a long term fragmentation less than vmalloc fallback. * However make sure that larger requests are not too disruptive - no * OOM killer and no allocation failure warnings as we have a fallback. */ Thanks, Bart.
diff --git a/drivers/scsi/sd_zbc.c b/drivers/scsi/sd_zbc.c index 7c4690f26698..f191af15de1b 100644 --- a/drivers/scsi/sd_zbc.c +++ b/drivers/scsi/sd_zbc.c @@ -104,11 +104,6 @@ static int sd_zbc_do_report_zones(struct scsi_disk *sdkp, unsigned char *buf, return 0; } -/* - * Maximum number of zones to get with one report zones command. - */ -#define SD_ZBC_REPORT_MAX_ZONES 8192U - /** * Allocate a buffer for report zones reply. * @sdkp: The target disk @@ -138,17 +133,22 @@ static void *sd_zbc_alloc_report_buffer(struct scsi_disk *sdkp, * sure that the allocated buffer can always be mapped by limiting the * number of pages allocated to the HBA max segments limit. */ - nr_zones = min(nr_zones, SD_ZBC_REPORT_MAX_ZONES); - bufsize = roundup((nr_zones + 1) * 64, 512); + nr_zones = min(nr_zones, sdkp->nr_zones); + bufsize = roundup((nr_zones + 1) * 64, SECTOR_SIZE); bufsize = min_t(size_t, bufsize, queue_max_hw_sectors(q) << SECTOR_SHIFT); bufsize = min_t(size_t, bufsize, queue_max_segments(q) << PAGE_SHIFT); - buf = vzalloc(bufsize); - if (buf) - *buflen = bufsize; + while (bufsize >= SECTOR_SIZE) { + buf = vzalloc(bufsize); + if (buf) { + *buflen = bufsize; + return buf; + } + bufsize >>= 1; + } - return buf; + return NULL; } /**
There is no need to arbitrarily limit the size of a report zone to the number of zones defined by SD_ZBC_REPORT_MAX_ZONES. Rather, simply calculate the report buffer size needed for the requested number of zones without exceeding the device total number of zones. This buffer size limitation to the hardware maximum transfer size and page mapping capabilities is kept unchanged. Starting with this initial buffer size, the allocation is optimized by iterating over decreasing buffer size until the allocation succeeds. This ensures forward progress for zone reports and avoids failures of zones revalidation under memory pressure. While at it, also replace the hard coded 512 B sector size with the SECTOR_SIZE macro. Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> --- drivers/scsi/sd_zbc.c | 22 +++++++++++----------- 1 file changed, 11 insertions(+), 11 deletions(-)