diff mbox series

[v3,2/2] usb: dwc3: Add cache type configuration support

Message ID 20191121024206.32933-2-ran.wang_1@nxp.com (mailing list archive)
State New, archived
Headers show
Series [v3,1/2] usb: dwc3: Add chip-specific compatible string | expand

Commit Message

Ran Wang Nov. 21, 2019, 2:42 a.m. UTC
This feature is telling how to configure cache type on 4 different
transfer types: Data Read, Desc Read, Data Write and Desc write. For each
treasfer type, controller has a 4-bit register field to enable different
cache type. Quoted from DWC3 data book Table 6-5 Cache Type Bit Assignments:
----------------------------------------------------------------
MBUS_TYPE| bit[3]       |bit[2]       |bit[1]     |bit[0]
----------------------------------------------------------------
AHB      |Cacheable     |Bufferable   |Privilegge |Data
AXI3     |Write Allocate|Read Allocate|Cacheable  |Bufferable
AXI4     |Allocate Other|Allocate     |Modifiable |Bufferable
AXI4     |Other Allocate|Allocate     |Modifiable |Bufferable
Native   |Same as AXI   |Same as AXI  |Same as AXI|Same as AXI
----------------------------------------------------------------
Note: The AHB, AXI3, AXI4, and PCIe busses use different names for certain
signals, which have the same meaning:
  Bufferable = Posted
  Cacheable = Modifiable = Snoop (negation of No Snoop)

In most cases, driver support is not required unless the default values of
registers are not correct *and* DWC3 node has enabled dma-coherent. So far we
have observed USB device detect failure on some Layerscape platforms if this
programming was not applied.

Related struct:
struct dwc3_cache_type {
	u8 transfer_type_datard;
	u8 transfer_type_descrd;
	u8 transfer_type_datawr;
	u8 transfer_type_descwr;
};

Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
---
Change in v3:
	- Replace cache type sub-node parsing with chip-specifc data parsing.

Change in v2:
	- Change most program logic to meet new DTS property define.
	- Rename related register address macros.
	- Rename function  dwc3_enable_snooping() to dwc3_set_cache_type().

 drivers/usb/dwc3/core.c | 67 ++++++++++++++++++++++++++++++++++++++++++++-----
 drivers/usb/dwc3/core.h | 15 +++++++++++
 2 files changed, 76 insertions(+), 6 deletions(-)

Comments

Peter Chen Nov. 21, 2019, 9:54 a.m. UTC | #1
On 19-11-21 10:42:06, Ran Wang wrote:
> This feature is telling how to configure cache type on 4 different
> transfer types: Data Read, Desc Read, Data Write and Desc write. For each
> treasfer type, controller has a 4-bit register field to enable different

%s/treasfer/transfer

> cache type. Quoted from DWC3 data book Table 6-5 Cache Type Bit Assignments:
> ----------------------------------------------------------------
> MBUS_TYPE| bit[3]       |bit[2]       |bit[1]     |bit[0]
> ----------------------------------------------------------------
> AHB      |Cacheable     |Bufferable   |Privilegge |Data
> AXI3     |Write Allocate|Read Allocate|Cacheable  |Bufferable
> AXI4     |Allocate Other|Allocate     |Modifiable |Bufferable
> AXI4     |Other Allocate|Allocate     |Modifiable |Bufferable
> Native   |Same as AXI   |Same as AXI  |Same as AXI|Same as AXI
> ----------------------------------------------------------------
> Note: The AHB, AXI3, AXI4, and PCIe busses use different names for certain
> signals, which have the same meaning:
>   Bufferable = Posted
>   Cacheable = Modifiable = Snoop (negation of No Snoop)
> 
> In most cases, driver support is not required unless the default values of
> registers are not correct *and* DWC3 node has enabled dma-coherent. So far we
> have observed USB device detect failure on some Layerscape platforms if this
> programming was not applied.
> 
> Related struct:
> struct dwc3_cache_type {
> 	u8 transfer_type_datard;
> 	u8 transfer_type_descrd;
> 	u8 transfer_type_datawr;
> 	u8 transfer_type_descwr;
> };
> 
> Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
> ---
> Change in v3:
> 	- Replace cache type sub-node parsing with chip-specifc data parsing.

If it is SoC implementation specific, you may move the implementation to
dwc3-of-simmple.c, and change your dts accordingly.

Feplie, what do you think?

Peter

> 
> Change in v2:
> 	- Change most program logic to meet new DTS property define.
> 	- Rename related register address macros.
> 	- Rename function  dwc3_enable_snooping() to dwc3_set_cache_type().
> 
>  drivers/usb/dwc3/core.c | 67 ++++++++++++++++++++++++++++++++++++++++++++-----
>  drivers/usb/dwc3/core.h | 15 +++++++++++
>  2 files changed, 76 insertions(+), 6 deletions(-)
> 
> diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
> index 97d6ae3..0baa972 100644
> --- a/drivers/usb/dwc3/core.c
> +++ b/drivers/usb/dwc3/core.c
> @@ -894,6 +894,53 @@ static void dwc3_set_incr_burst_type(struct dwc3 *dwc)
>  	dwc3_writel(dwc->regs, DWC3_GSBUSCFG0, cfg);
>  }
>  
> +#ifdef CONFIG_OF
> +struct dwc3_cache_type {
> +	u8 transfer_type_datard;
> +	u8 transfer_type_descrd;
> +	u8 transfer_type_datawr;
> +	u8 transfer_type_descwr;
> +};
> +
> +static const struct dwc3_cache_type ls1088a_dwc3_cache_type = {
> +	.transfer_type_datard = 2,
> +	.transfer_type_descrd = 2,
> +	.transfer_type_datawr = 2,
> +	.transfer_type_descwr = 2,
> +};
> +
> +/**
> + * dwc3_set_cache_type - Configure cache type registers
> + * @dwc: Pointer to our controller context structure
> + */
> +static void dwc3_set_cache_type(struct dwc3 *dwc)
> +{
> +	u32 tmp, reg;
> +	const struct dwc3_cache_type *cache_type =
> +		device_get_match_data(dwc->dev);
> +
> +	if (cache_type) {
> +		reg = dwc3_readl(dwc->regs,  DWC3_GSBUSCFG0);
> +		tmp = reg;
> +
> +		reg &= ~DWC3_GSBUSCFG0_DATARD(~0);
> +		reg |= DWC3_GSBUSCFG0_DATARD(cache_type->transfer_type_datard);
> +
> +		reg &= ~DWC3_GSBUSCFG0_DESCRD(~0);
> +		reg |= DWC3_GSBUSCFG0_DESCRD(cache_type->transfer_type_descrd);
> +
> +		reg &= ~DWC3_GSBUSCFG0_DATAWR(~0);
> +		reg |= DWC3_GSBUSCFG0_DATAWR(cache_type->transfer_type_datawr);
> +
> +		reg &= ~DWC3_GSBUSCFG0_DESCWR(~0);
> +		reg |= DWC3_GSBUSCFG0_DESCWR(cache_type->transfer_type_descwr);
> +
> +		if (tmp != reg)
> +			dwc3_writel(dwc->regs, DWC3_GSBUSCFG0, reg);
> +	}
> +}
> +#endif
> +
>  /**
>   * dwc3_core_init - Low-level initialization of DWC3 Core
>   * @dwc: Pointer to our controller context structure
> @@ -952,6 +999,10 @@ static int dwc3_core_init(struct dwc3 *dwc)
>  
>  	dwc3_set_incr_burst_type(dwc);
>  
> +#ifdef CONFIG_OF
> +	dwc3_set_cache_type(dwc);
> +#endif
> +
>  	usb_phy_set_suspend(dwc->usb2_phy, 0);
>  	usb_phy_set_suspend(dwc->usb3_phy, 0);
>  	ret = phy_power_on(dwc->usb2_generic_phy);
> @@ -1837,12 +1888,16 @@ static const struct dev_pm_ops dwc3_dev_pm_ops = {
>  
>  #ifdef CONFIG_OF
>  static const struct of_device_id of_dwc3_match[] = {
> -	{
> -		.compatible = "snps,dwc3"
> -	},
> -	{
> -		.compatible = "synopsys,dwc3"
> -	},
> +	{ .compatible = "fsl,ls1012a-dwc3", .data = &ls1088a_dwc3_cache_type, },
> +	{ .compatible = "fsl,ls1021a-dwc3", .data = &ls1088a_dwc3_cache_type, },
> +	{ .compatible = "fsl,ls1028a-dwc3", .data = &ls1088a_dwc3_cache_type, },
> +	{ .compatible = "fsl,ls1043a-dwc3", .data = &ls1088a_dwc3_cache_type, },
> +	{ .compatible = "fsl,ls1046a-dwc3", .data = &ls1088a_dwc3_cache_type, },
> +	{ .compatible = "fsl,ls1088a-dwc3", .data = &ls1088a_dwc3_cache_type, },
> +	{ .compatible = "fsl,ls2088a-dwc3", .data = &ls1088a_dwc3_cache_type, },
> +	{ .compatible = "fsl,lx2160a-dwc3", .data = &ls1088a_dwc3_cache_type, },
> +	{ .compatible = "snps,dwc3" },
> +	{ .compatible = "synopsys,dwc3"	},
>  	{ },
>  };
>  MODULE_DEVICE_TABLE(of, of_dwc3_match);
> diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
> index 1c8b3493..ac51dfe 100644
> --- a/drivers/usb/dwc3/core.h
> +++ b/drivers/usb/dwc3/core.h
> @@ -165,6 +165,21 @@
>  /* Bit fields */
>  
>  /* Global SoC Bus Configuration INCRx Register 0 */
> +#ifdef CONFIG_OF
> +#define DWC3_GSBUSCFG0_DATARD_SHIFT	28
> +#define DWC3_GSBUSCFG0_DATARD(n)	(((n) & 0xf)		\
> +			<< DWC3_GSBUSCFG0_DATARD_SHIFT)
> +#define DWC3_GSBUSCFG0_DESCRD_SHIFT	24
> +#define DWC3_GSBUSCFG0_DESCRD(n)	(((n) & 0xf)		\
> +			<< DWC3_GSBUSCFG0_DESCRD_SHIFT)
> +#define DWC3_GSBUSCFG0_DATAWR_SHIFT	20
> +#define DWC3_GSBUSCFG0_DATAWR(n)	(((n) & 0xf)		\
> +			<< DWC3_GSBUSCFG0_DATAWR_SHIFT)
> +#define DWC3_GSBUSCFG0_DESCWR_SHIFT	16
> +#define DWC3_GSBUSCFG0_DESCWR(n)	(((n) & 0xf)		\
> +			<< DWC3_GSBUSCFG0_DESCWR_SHIFT)
> +#endif
> +
>  #define DWC3_GSBUSCFG0_INCR256BRSTENA	(1 << 7) /* INCR256 burst */
>  #define DWC3_GSBUSCFG0_INCR128BRSTENA	(1 << 6) /* INCR128 burst */
>  #define DWC3_GSBUSCFG0_INCR64BRSTENA	(1 << 5) /* INCR64 burst */
> -- 
> 2.7.4
>
diff mbox series

Patch

diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
index 97d6ae3..0baa972 100644
--- a/drivers/usb/dwc3/core.c
+++ b/drivers/usb/dwc3/core.c
@@ -894,6 +894,53 @@  static void dwc3_set_incr_burst_type(struct dwc3 *dwc)
 	dwc3_writel(dwc->regs, DWC3_GSBUSCFG0, cfg);
 }
 
+#ifdef CONFIG_OF
+struct dwc3_cache_type {
+	u8 transfer_type_datard;
+	u8 transfer_type_descrd;
+	u8 transfer_type_datawr;
+	u8 transfer_type_descwr;
+};
+
+static const struct dwc3_cache_type ls1088a_dwc3_cache_type = {
+	.transfer_type_datard = 2,
+	.transfer_type_descrd = 2,
+	.transfer_type_datawr = 2,
+	.transfer_type_descwr = 2,
+};
+
+/**
+ * dwc3_set_cache_type - Configure cache type registers
+ * @dwc: Pointer to our controller context structure
+ */
+static void dwc3_set_cache_type(struct dwc3 *dwc)
+{
+	u32 tmp, reg;
+	const struct dwc3_cache_type *cache_type =
+		device_get_match_data(dwc->dev);
+
+	if (cache_type) {
+		reg = dwc3_readl(dwc->regs,  DWC3_GSBUSCFG0);
+		tmp = reg;
+
+		reg &= ~DWC3_GSBUSCFG0_DATARD(~0);
+		reg |= DWC3_GSBUSCFG0_DATARD(cache_type->transfer_type_datard);
+
+		reg &= ~DWC3_GSBUSCFG0_DESCRD(~0);
+		reg |= DWC3_GSBUSCFG0_DESCRD(cache_type->transfer_type_descrd);
+
+		reg &= ~DWC3_GSBUSCFG0_DATAWR(~0);
+		reg |= DWC3_GSBUSCFG0_DATAWR(cache_type->transfer_type_datawr);
+
+		reg &= ~DWC3_GSBUSCFG0_DESCWR(~0);
+		reg |= DWC3_GSBUSCFG0_DESCWR(cache_type->transfer_type_descwr);
+
+		if (tmp != reg)
+			dwc3_writel(dwc->regs, DWC3_GSBUSCFG0, reg);
+	}
+}
+#endif
+
 /**
  * dwc3_core_init - Low-level initialization of DWC3 Core
  * @dwc: Pointer to our controller context structure
@@ -952,6 +999,10 @@  static int dwc3_core_init(struct dwc3 *dwc)
 
 	dwc3_set_incr_burst_type(dwc);
 
+#ifdef CONFIG_OF
+	dwc3_set_cache_type(dwc);
+#endif
+
 	usb_phy_set_suspend(dwc->usb2_phy, 0);
 	usb_phy_set_suspend(dwc->usb3_phy, 0);
 	ret = phy_power_on(dwc->usb2_generic_phy);
@@ -1837,12 +1888,16 @@  static const struct dev_pm_ops dwc3_dev_pm_ops = {
 
 #ifdef CONFIG_OF
 static const struct of_device_id of_dwc3_match[] = {
-	{
-		.compatible = "snps,dwc3"
-	},
-	{
-		.compatible = "synopsys,dwc3"
-	},
+	{ .compatible = "fsl,ls1012a-dwc3", .data = &ls1088a_dwc3_cache_type, },
+	{ .compatible = "fsl,ls1021a-dwc3", .data = &ls1088a_dwc3_cache_type, },
+	{ .compatible = "fsl,ls1028a-dwc3", .data = &ls1088a_dwc3_cache_type, },
+	{ .compatible = "fsl,ls1043a-dwc3", .data = &ls1088a_dwc3_cache_type, },
+	{ .compatible = "fsl,ls1046a-dwc3", .data = &ls1088a_dwc3_cache_type, },
+	{ .compatible = "fsl,ls1088a-dwc3", .data = &ls1088a_dwc3_cache_type, },
+	{ .compatible = "fsl,ls2088a-dwc3", .data = &ls1088a_dwc3_cache_type, },
+	{ .compatible = "fsl,lx2160a-dwc3", .data = &ls1088a_dwc3_cache_type, },
+	{ .compatible = "snps,dwc3" },
+	{ .compatible = "synopsys,dwc3"	},
 	{ },
 };
 MODULE_DEVICE_TABLE(of, of_dwc3_match);
diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
index 1c8b3493..ac51dfe 100644
--- a/drivers/usb/dwc3/core.h
+++ b/drivers/usb/dwc3/core.h
@@ -165,6 +165,21 @@ 
 /* Bit fields */
 
 /* Global SoC Bus Configuration INCRx Register 0 */
+#ifdef CONFIG_OF
+#define DWC3_GSBUSCFG0_DATARD_SHIFT	28
+#define DWC3_GSBUSCFG0_DATARD(n)	(((n) & 0xf)		\
+			<< DWC3_GSBUSCFG0_DATARD_SHIFT)
+#define DWC3_GSBUSCFG0_DESCRD_SHIFT	24
+#define DWC3_GSBUSCFG0_DESCRD(n)	(((n) & 0xf)		\
+			<< DWC3_GSBUSCFG0_DESCRD_SHIFT)
+#define DWC3_GSBUSCFG0_DATAWR_SHIFT	20
+#define DWC3_GSBUSCFG0_DATAWR(n)	(((n) & 0xf)		\
+			<< DWC3_GSBUSCFG0_DATAWR_SHIFT)
+#define DWC3_GSBUSCFG0_DESCWR_SHIFT	16
+#define DWC3_GSBUSCFG0_DESCWR(n)	(((n) & 0xf)		\
+			<< DWC3_GSBUSCFG0_DESCWR_SHIFT)
+#endif
+
 #define DWC3_GSBUSCFG0_INCR256BRSTENA	(1 << 7) /* INCR256 burst */
 #define DWC3_GSBUSCFG0_INCR128BRSTENA	(1 << 6) /* INCR128 burst */
 #define DWC3_GSBUSCFG0_INCR64BRSTENA	(1 << 5) /* INCR64 burst */