| Message ID | 20191120114334.2287-4-frankja@linux.ibm.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | s390x: Protected Virtualization support | expand |
On Wed, 20 Nov 2019 06:43:22 -0500 Janosch Frank <frankja@linux.ibm.com> wrote: > For diag308 subcodes 8 - 10 we have a new ipib of type 5. The ipib > holds the address and length of the secure execution header, as well > as a list of guest components. > > Each component is a block of memory, for example kernel or initrd, > which needs to be decrypted by the Ultravisor in order to run a > protected VM. The secure execution header instructs the Ultravisor on > how to handle the protected VM and its components. > > Subcodes 8 and 9 are similiar to 5 and 6 and subcode 10 will finally > start the protected guest. > > Subcodes 8-10 are not valid in protected mode, we have to do a subcode > 3 and then the 8 and 10 combination for a protected reboot. > > Signed-off-by: Janosch Frank <frankja@linux.ibm.com> > --- > hw/s390x/ipl.c | 48 ++++++++++++++++++++++++++++++++++++++++++--- > hw/s390x/ipl.h | 33 +++++++++++++++++++++++++++++++ > target/s390x/diag.c | 26 ++++++++++++++++++++++-- > 3 files changed, 102 insertions(+), 5 deletions(-) > > diff --git a/hw/s390x/ipl.c b/hw/s390x/ipl.c > index ca544d64c5..a077926f36 100644 > --- a/hw/s390x/ipl.c > +++ b/hw/s390x/ipl.c > @@ -529,15 +529,56 @@ static bool is_virtio_scsi_device(IplParameterBlock *iplb) > return is_virtio_ccw_device_of_type(iplb, VIRTIO_ID_SCSI); > } > > +int s390_ipl_pv_check_comp(IplParameterBlock *iplb) s390_ipl_pv_check_components() ? > +{ > + int i; > + IPLBlockPV *ipib_pv = &iplb->pv; > + > + if (ipib_pv->num_comp == 0) { > + return -EINVAL; > + } > + > + for (i = 0; i < ipib_pv->num_comp; i++) { > + > + /* Addr must be 4k aligned */ > + if (ipib_pv->components[i].addr & ~TARGET_PAGE_MASK) { > + return -EINVAL; > + } > + > + /* Tweak prefix is monotonously increasing with each component */ > + if (i < ipib_pv->num_comp - 1 && > + ipib_pv->components[i].tweak_pref > > + ipib_pv->components[i + 1].tweak_pref) { > + return -EINVAL; > + } > + } > + return 1; > +} > + (...) > @@ -185,4 +211,11 @@ static inline bool iplb_valid_fcp(IplParameterBlock *iplb) > iplb->pbt == S390_IPL_TYPE_FCP; > } > > +static inline bool iplb_valid_se(IplParameterBlock *iplb) iplb_valid_pv() ? > +{ > + return be32_to_cpu(iplb->len) >= S390_IPLB_MIN_PV_LEN && > + iplb->pbt == S390_IPL_TYPE_PV; > +} > + > + > #endif (...) > @@ -105,6 +110,7 @@ void handle_diag_308(CPUS390XState *env, uint64_t r1, uint64_t r3, uintptr_t ra) > s390_ipl_reset_request(cs, S390_RESET_REIPL); > break; > case DIAG308_SET: > + case DIAG308_PV_SET: /* Set SE parms */ PV parms? ('SE' makes me think of 'service element' :) > if (diag308_parm_check(env, r1, addr, ra, false)) { > return; > } > @@ -117,7 +123,8 @@ void handle_diag_308(CPUS390XState *env, uint64_t r1, uint64_t r3, uintptr_t ra) > > cpu_physical_memory_read(addr, iplb, be32_to_cpu(iplb->len)); > > - if (!iplb_valid_ccw(iplb) && !iplb_valid_fcp(iplb)) { > + if (!iplb_valid_ccw(iplb) && !iplb_valid_fcp(iplb) && > + !(iplb_valid_se(iplb) && s390_ipl_pv_check_comp(iplb) >= 0)) { > env->regs[r1 + 1] = DIAG_308_RC_INVALID; > goto out; > } > @@ -128,10 +135,15 @@ out: > g_free(iplb); > return; > case DIAG308_STORE: > + case DIAG308_PV_STORE: /* Get SE parms */ Same here. > if (diag308_parm_check(env, r1, addr, ra, true)) { > return; > } > - iplb = s390_ipl_get_iplb(); > + if (subcode == DIAG308_PV_STORE) { > + iplb = s390_ipl_get_iplb_secure(); > + } else { > + iplb = s390_ipl_get_iplb(); > + } > if (iplb) { > cpu_physical_memory_write(addr, iplb, be32_to_cpu(iplb->len)); > env->regs[r1 + 1] = DIAG_308_RC_OK; > @@ -139,6 +151,16 @@ out: > env->regs[r1 + 1] = DIAG_308_RC_NO_CONF; > } > return; > + break; > + case DIAG308_PV_START: /* SE start */ Also here :) > + iplb = s390_ipl_get_iplb_secure(); > + if (!iplb_valid_se(iplb)) { > + env->regs[r1 + 1] = DIAG_308_RC_NO_PV_CONF; > + return; > + } > + > + s390_ipl_reset_request(cs, S390_RESET_PV); > + break; > default: > s390_program_interrupt(env, PGM_SPECIFICATION, ra); > break; Did not spot anything else.
On 20/11/2019 12.43, Janosch Frank wrote: > For diag308 subcodes 8 - 10 we have a new ipib of type 5. The ipib > holds the address and length of the secure execution header, as well > as a list of guest components. > > Each component is a block of memory, for example kernel or initrd, > which needs to be decrypted by the Ultravisor in order to run a > protected VM. The secure execution header instructs the Ultravisor on > how to handle the protected VM and its components. > > Subcodes 8 and 9 are similiar to 5 and 6 and subcode 10 will finally > start the protected guest. > > Subcodes 8-10 are not valid in protected mode, we have to do a subcode > 3 and then the 8 and 10 combination for a protected reboot. > > Signed-off-by: Janosch Frank <frankja@linux.ibm.com> > --- [...] > diff --git a/hw/s390x/ipl.h b/hw/s390x/ipl.h > index d4813105db..7b8a493509 100644 > --- a/hw/s390x/ipl.h > +++ b/hw/s390x/ipl.h > @@ -15,6 +15,24 @@ > #include "cpu.h" > #include "hw/qdev-core.h" > > +struct IPLBlockPVComp { > + uint64_t tweak_pref; > + uint64_t addr; > + uint64_t size; > +} QEMU_PACKED; > +typedef struct IPLBlockPVComp IPLBlockPVComp; > + > +struct IPLBlockPV { > + uint8_t reserved[84]; > + uint8_t reserved67[3]; What does the "67" mean here? > + uint8_t version; > + uint32_t num_comp; > + uint64_t pv_header_addr; > + uint64_t pv_header_len; > + struct IPLBlockPVComp components[]; > +} QEMU_PACKED; > +typedef struct IPLBlockPV IPLBlockPV; Given the fact that we had quite some headaches with QEMU_PACKED structs in the past already, and the structs seem to be naturally aligned ... what about dropping the QEMU_PACKED here and using QEMU_BUILD_BUG() to assert that the struct has the correct size? [...] > @@ -185,4 +211,11 @@ static inline bool iplb_valid_fcp(IplParameterBlock *iplb) > iplb->pbt == S390_IPL_TYPE_FCP; > } > > +static inline bool iplb_valid_se(IplParameterBlock *iplb) > +{ > + return be32_to_cpu(iplb->len) >= S390_IPLB_MIN_PV_LEN && > + iplb->pbt == S390_IPL_TYPE_PV; > +} > + > + Drop one empty line? > #endif > diff --git a/target/s390x/diag.c b/target/s390x/diag.c > index 067c667ba7..32049bb4ee 100644 > --- a/target/s390x/diag.c > +++ b/target/s390x/diag.c > @@ -52,6 +52,8 @@ int handle_diag_288(CPUS390XState *env, uint64_t r1, uint64_t r3) > #define DIAG_308_RC_OK 0x0001 > #define DIAG_308_RC_NO_CONF 0x0102 > #define DIAG_308_RC_INVALID 0x0402 > +#define DIAG_308_RC_NO_PV_CONF 0x0a02 > +#define DIAG_308_RC_INV_FOR_PV 0x0b02 > > #define DIAG308_RES_MOD_CLR 0 > #define DIAG308_RES_LOAD_NORM 1 > @@ -59,6 +61,9 @@ int handle_diag_288(CPUS390XState *env, uint64_t r1, uint64_t r3) > #define DIAG308_LOAD_NORMAL_DUMP 4 > #define DIAG308_SET 5 > #define DIAG308_STORE 6 > +#define DIAG308_PV_SET 8 > +#define DIAG308_PV_STORE 9 > +#define DIAG308_PV_START 10 > > static int diag308_parm_check(CPUS390XState *env, uint64_t r1, uint64_t addr, > uintptr_t ra, bool write) > @@ -105,6 +110,7 @@ void handle_diag_308(CPUS390XState *env, uint64_t r1, uint64_t r3, uintptr_t ra) > s390_ipl_reset_request(cs, S390_RESET_REIPL); > break; > case DIAG308_SET: > + case DIAG308_PV_SET: /* Set SE parms */ > if (diag308_parm_check(env, r1, addr, ra, false)) { > return; > } > @@ -117,7 +123,8 @@ void handle_diag_308(CPUS390XState *env, uint64_t r1, uint64_t r3, uintptr_t ra) > > cpu_physical_memory_read(addr, iplb, be32_to_cpu(iplb->len)); > > - if (!iplb_valid_ccw(iplb) && !iplb_valid_fcp(iplb)) { > + if (!iplb_valid_ccw(iplb) && !iplb_valid_fcp(iplb) && > + !(iplb_valid_se(iplb) && s390_ipl_pv_check_comp(iplb) >= 0)) { > env->regs[r1 + 1] = DIAG_308_RC_INVALID; > goto out; > } > @@ -128,10 +135,15 @@ out: > g_free(iplb); > return; > case DIAG308_STORE: > + case DIAG308_PV_STORE: /* Get SE parms */ > if (diag308_parm_check(env, r1, addr, ra, true)) { > return; > } > - iplb = s390_ipl_get_iplb(); > + if (subcode == DIAG308_PV_STORE) { > + iplb = s390_ipl_get_iplb_secure(); > + } else { > + iplb = s390_ipl_get_iplb(); > + } > if (iplb) { > cpu_physical_memory_write(addr, iplb, be32_to_cpu(iplb->len)); > env->regs[r1 + 1] = DIAG_308_RC_OK; > @@ -139,6 +151,16 @@ out: > env->regs[r1 + 1] = DIAG_308_RC_NO_CONF; > } > return; > + break; <hamletmode> To return or to break, that's the question... </hamletmode> ... please choose one of the two. > + case DIAG308_PV_START: /* SE start */ > + iplb = s390_ipl_get_iplb_secure(); > + if (!iplb_valid_se(iplb)) { > + env->regs[r1 + 1] = DIAG_308_RC_NO_PV_CONF; > + return; > + } > + > + s390_ipl_reset_request(cs, S390_RESET_PV); > + break; > default: > s390_program_interrupt(env, PGM_SPECIFICATION, ra); > break; > Thomas
On 11/21/19 3:36 PM, Thomas Huth wrote: > On 20/11/2019 12.43, Janosch Frank wrote: >> For diag308 subcodes 8 - 10 we have a new ipib of type 5. The ipib >> holds the address and length of the secure execution header, as well >> as a list of guest components. >> >> Each component is a block of memory, for example kernel or initrd, >> which needs to be decrypted by the Ultravisor in order to run a >> protected VM. The secure execution header instructs the Ultravisor on >> how to handle the protected VM and its components. >> >> Subcodes 8 and 9 are similiar to 5 and 6 and subcode 10 will finally >> start the protected guest. >> >> Subcodes 8-10 are not valid in protected mode, we have to do a subcode >> 3 and then the 8 and 10 combination for a protected reboot. >> >> Signed-off-by: Janosch Frank <frankja@linux.ibm.com> >> --- > [...] >> diff --git a/hw/s390x/ipl.h b/hw/s390x/ipl.h >> index d4813105db..7b8a493509 100644 >> --- a/hw/s390x/ipl.h >> +++ b/hw/s390x/ipl.h >> @@ -15,6 +15,24 @@ >> #include "cpu.h" >> #include "hw/qdev-core.h" >> >> +struct IPLBlockPVComp { >> + uint64_t tweak_pref; >> + uint64_t addr; >> + uint64_t size; >> +} QEMU_PACKED; >> +typedef struct IPLBlockPVComp IPLBlockPVComp; >> + >> +struct IPLBlockPV { >> + uint8_t reserved[84]; >> + uint8_t reserved67[3]; > > What does the "67" mean here? Was compacted to reserved[87] > >> + uint8_t version; >> + uint32_t num_comp; >> + uint64_t pv_header_addr; >> + uint64_t pv_header_len; >> + struct IPLBlockPVComp components[]; >> +} QEMU_PACKED; >> +typedef struct IPLBlockPV IPLBlockPV; > > Given the fact that we had quite some headaches with QEMU_PACKED structs > in the past already, and the structs seem to be naturally aligned ... > what about dropping the QEMU_PACKED here and using QEMU_BUILD_BUG() to > assert that the struct has the correct size? As the struct in which IPLBlockPV is embeded are also packed, removing the PACKED annotation results in this: /mnt/dev/qemu/hw/s390x/ipl.c:544:27: error: taking address of packed member of ‘struct <anonymous>’ may result in an unaligned pointer value [-Werror=address-of-packed-member] > > [...] >> @@ -185,4 +211,11 @@ static inline bool iplb_valid_fcp(IplParameterBlock *iplb) >> iplb->pbt == S390_IPL_TYPE_FCP; >> } >> >> +static inline bool iplb_valid_se(IplParameterBlock *iplb) >> +{ >> + return be32_to_cpu(iplb->len) >= S390_IPLB_MIN_PV_LEN && >> + iplb->pbt == S390_IPL_TYPE_PV; >> +} >> + >> + > > Drop one empty line? ack. > >> #endif >> diff --git a/target/s390x/diag.c b/target/s390x/diag.c >> index 067c667ba7..32049bb4ee 100644 >> --- a/target/s390x/diag.c >> +++ b/target/s390x/diag.c >> @@ -52,6 +52,8 @@ int handle_diag_288(CPUS390XState *env, uint64_t r1, uint64_t r3) >> #define DIAG_308_RC_OK 0x0001 >> #define DIAG_308_RC_NO_CONF 0x0102 >> #define DIAG_308_RC_INVALID 0x0402 >> +#define DIAG_308_RC_NO_PV_CONF 0x0a02 >> +#define DIAG_308_RC_INV_FOR_PV 0x0b02 >> >> #define DIAG308_RES_MOD_CLR 0 >> #define DIAG308_RES_LOAD_NORM 1 >> @@ -59,6 +61,9 @@ int handle_diag_288(CPUS390XState *env, uint64_t r1, uint64_t r3) >> #define DIAG308_LOAD_NORMAL_DUMP 4 >> #define DIAG308_SET 5 >> #define DIAG308_STORE 6 >> +#define DIAG308_PV_SET 8 >> +#define DIAG308_PV_STORE 9 >> +#define DIAG308_PV_START 10 >> >> static int diag308_parm_check(CPUS390XState *env, uint64_t r1, uint64_t addr, >> uintptr_t ra, bool write) >> @@ -105,6 +110,7 @@ void handle_diag_308(CPUS390XState *env, uint64_t r1, uint64_t r3, uintptr_t ra) >> s390_ipl_reset_request(cs, S390_RESET_REIPL); >> break; >> case DIAG308_SET: >> + case DIAG308_PV_SET: /* Set SE parms */ >> if (diag308_parm_check(env, r1, addr, ra, false)) { >> return; >> } >> @@ -117,7 +123,8 @@ void handle_diag_308(CPUS390XState *env, uint64_t r1, uint64_t r3, uintptr_t ra) >> >> cpu_physical_memory_read(addr, iplb, be32_to_cpu(iplb->len)); >> >> - if (!iplb_valid_ccw(iplb) && !iplb_valid_fcp(iplb)) { >> + if (!iplb_valid_ccw(iplb) && !iplb_valid_fcp(iplb) && >> + !(iplb_valid_se(iplb) && s390_ipl_pv_check_comp(iplb) >= 0)) { >> env->regs[r1 + 1] = DIAG_308_RC_INVALID; >> goto out; >> } >> @@ -128,10 +135,15 @@ out: >> g_free(iplb); >> return; >> case DIAG308_STORE: >> + case DIAG308_PV_STORE: /* Get SE parms */ >> if (diag308_parm_check(env, r1, addr, ra, true)) { >> return; >> } >> - iplb = s390_ipl_get_iplb(); >> + if (subcode == DIAG308_PV_STORE) { >> + iplb = s390_ipl_get_iplb_secure(); >> + } else { >> + iplb = s390_ipl_get_iplb(); >> + } >> if (iplb) { >> cpu_physical_memory_write(addr, iplb, be32_to_cpu(iplb->len)); >> env->regs[r1 + 1] = DIAG_308_RC_OK; >> @@ -139,6 +151,16 @@ out: >> env->regs[r1 + 1] = DIAG_308_RC_NO_CONF; >> } >> return; >> + break; > > <hamletmode> > To return or to break, that's the question... > </hamletmode> > > ... please choose one of the two. > >> + case DIAG308_PV_START: /* SE start */ >> + iplb = s390_ipl_get_iplb_secure(); >> + if (!iplb_valid_se(iplb)) { >> + env->regs[r1 + 1] = DIAG_308_RC_NO_PV_CONF; >> + return; >> + } >> + >> + s390_ipl_reset_request(cs, S390_RESET_PV); >> + break; >> default: >> s390_program_interrupt(env, PGM_SPECIFICATION, ra); >> break; >> > > Thomas > >
diff --git a/hw/s390x/ipl.c b/hw/s390x/ipl.c index ca544d64c5..a077926f36 100644 --- a/hw/s390x/ipl.c +++ b/hw/s390x/ipl.c @@ -529,15 +529,56 @@ static bool is_virtio_scsi_device(IplParameterBlock *iplb) return is_virtio_ccw_device_of_type(iplb, VIRTIO_ID_SCSI); } +int s390_ipl_pv_check_comp(IplParameterBlock *iplb) +{ + int i; + IPLBlockPV *ipib_pv = &iplb->pv; + + if (ipib_pv->num_comp == 0) { + return -EINVAL; + } + + for (i = 0; i < ipib_pv->num_comp; i++) { + + /* Addr must be 4k aligned */ + if (ipib_pv->components[i].addr & ~TARGET_PAGE_MASK) { + return -EINVAL; + } + + /* Tweak prefix is monotonously increasing with each component */ + if (i < ipib_pv->num_comp - 1 && + ipib_pv->components[i].tweak_pref > + ipib_pv->components[i + 1].tweak_pref) { + return -EINVAL; + } + } + return 1; +} + void s390_ipl_update_diag308(IplParameterBlock *iplb) { S390IPLState *ipl = get_ipl_device(); - ipl->iplb = *iplb; - ipl->iplb_valid = true; + if (iplb->pbt == 5) { + ipl->iplb_pbt5 = *iplb; + ipl->iplb_valid_pbt5 = true; + } else { + ipl->iplb = *iplb; + ipl->iplb_valid = true; + } ipl->netboot = is_virtio_net_device(iplb); } +IplParameterBlock *s390_ipl_get_iplb_secure(void) +{ + S390IPLState *ipl = get_ipl_device(); + + if (!ipl->iplb_valid_pbt5) { + return NULL; + } + return &ipl->iplb_pbt5; +} + IplParameterBlock *s390_ipl_get_iplb(void) { S390IPLState *ipl = get_ipl_device(); @@ -552,7 +593,8 @@ void s390_ipl_reset_request(CPUState *cs, enum s390_reset reset_type) { S390IPLState *ipl = get_ipl_device(); - if (reset_type == S390_RESET_EXTERNAL || reset_type == S390_RESET_REIPL) { + if (reset_type == S390_RESET_EXTERNAL || reset_type == S390_RESET_REIPL || + reset_type == S390_RESET_PV) { /* use CPU 0 for full resets */ ipl->reset_cpu_index = 0; } else { diff --git a/hw/s390x/ipl.h b/hw/s390x/ipl.h index d4813105db..7b8a493509 100644 --- a/hw/s390x/ipl.h +++ b/hw/s390x/ipl.h @@ -15,6 +15,24 @@ #include "cpu.h" #include "hw/qdev-core.h" +struct IPLBlockPVComp { + uint64_t tweak_pref; + uint64_t addr; + uint64_t size; +} QEMU_PACKED; +typedef struct IPLBlockPVComp IPLBlockPVComp; + +struct IPLBlockPV { + uint8_t reserved[84]; + uint8_t reserved67[3]; + uint8_t version; + uint32_t num_comp; + uint64_t pv_header_addr; + uint64_t pv_header_len; + struct IPLBlockPVComp components[]; +} QEMU_PACKED; +typedef struct IPLBlockPV IPLBlockPV; + struct IplBlockCcw { uint8_t reserved0[85]; uint8_t ssid; @@ -71,6 +89,7 @@ union IplParameterBlock { union { IplBlockCcw ccw; IplBlockFcp fcp; + IPLBlockPV pv; IplBlockQemuScsi scsi; }; } QEMU_PACKED; @@ -84,9 +103,11 @@ union IplParameterBlock { typedef union IplParameterBlock IplParameterBlock; int s390_ipl_set_loadparm(uint8_t *loadparm); +int s390_ipl_pv_check_comp(IplParameterBlock *iplb); void s390_ipl_update_diag308(IplParameterBlock *iplb); void s390_ipl_prepare_cpu(S390CPU *cpu); IplParameterBlock *s390_ipl_get_iplb(void); +IplParameterBlock *s390_ipl_get_iplb_secure(void); enum s390_reset { /* default is a reset not triggered by a CPU e.g. issued by QMP */ @@ -94,6 +115,7 @@ enum s390_reset { S390_RESET_REIPL, S390_RESET_MODIFIED_CLEAR, S390_RESET_LOAD_NORMAL, + S390_RESET_PV, }; void s390_ipl_reset_request(CPUState *cs, enum s390_reset reset_type); void s390_ipl_get_reset_request(CPUState **cs, enum s390_reset *reset_type); @@ -133,6 +155,7 @@ struct S390IPLState { /*< private >*/ DeviceState parent_obj; IplParameterBlock iplb; + IplParameterBlock iplb_pbt5; QemuIplParameters qipl; uint64_t start_addr; uint64_t compat_start_addr; @@ -140,6 +163,7 @@ struct S390IPLState { uint64_t compat_bios_start_addr; bool enforce_bios; bool iplb_valid; + bool iplb_valid_pbt5; bool netboot; /* reset related properties don't have to be migrated or reset */ enum s390_reset reset_type; @@ -161,9 +185,11 @@ QEMU_BUILD_BUG_MSG(offsetof(S390IPLState, iplb) & 3, "alignment of iplb wrong"); #define S390_IPL_TYPE_FCP 0x00 #define S390_IPL_TYPE_CCW 0x02 +#define S390_IPL_TYPE_PV 0x05 #define S390_IPL_TYPE_QEMU_SCSI 0xff #define S390_IPLB_HEADER_LEN 8 +#define S390_IPLB_MIN_PV_LEN 148 #define S390_IPLB_MIN_CCW_LEN 200 #define S390_IPLB_MIN_FCP_LEN 384 #define S390_IPLB_MIN_QEMU_SCSI_LEN 200 @@ -185,4 +211,11 @@ static inline bool iplb_valid_fcp(IplParameterBlock *iplb) iplb->pbt == S390_IPL_TYPE_FCP; } +static inline bool iplb_valid_se(IplParameterBlock *iplb) +{ + return be32_to_cpu(iplb->len) >= S390_IPLB_MIN_PV_LEN && + iplb->pbt == S390_IPL_TYPE_PV; +} + + #endif diff --git a/target/s390x/diag.c b/target/s390x/diag.c index 067c667ba7..32049bb4ee 100644 --- a/target/s390x/diag.c +++ b/target/s390x/diag.c @@ -52,6 +52,8 @@ int handle_diag_288(CPUS390XState *env, uint64_t r1, uint64_t r3) #define DIAG_308_RC_OK 0x0001 #define DIAG_308_RC_NO_CONF 0x0102 #define DIAG_308_RC_INVALID 0x0402 +#define DIAG_308_RC_NO_PV_CONF 0x0a02 +#define DIAG_308_RC_INV_FOR_PV 0x0b02 #define DIAG308_RES_MOD_CLR 0 #define DIAG308_RES_LOAD_NORM 1 @@ -59,6 +61,9 @@ int handle_diag_288(CPUS390XState *env, uint64_t r1, uint64_t r3) #define DIAG308_LOAD_NORMAL_DUMP 4 #define DIAG308_SET 5 #define DIAG308_STORE 6 +#define DIAG308_PV_SET 8 +#define DIAG308_PV_STORE 9 +#define DIAG308_PV_START 10 static int diag308_parm_check(CPUS390XState *env, uint64_t r1, uint64_t addr, uintptr_t ra, bool write) @@ -105,6 +110,7 @@ void handle_diag_308(CPUS390XState *env, uint64_t r1, uint64_t r3, uintptr_t ra) s390_ipl_reset_request(cs, S390_RESET_REIPL); break; case DIAG308_SET: + case DIAG308_PV_SET: /* Set SE parms */ if (diag308_parm_check(env, r1, addr, ra, false)) { return; } @@ -117,7 +123,8 @@ void handle_diag_308(CPUS390XState *env, uint64_t r1, uint64_t r3, uintptr_t ra) cpu_physical_memory_read(addr, iplb, be32_to_cpu(iplb->len)); - if (!iplb_valid_ccw(iplb) && !iplb_valid_fcp(iplb)) { + if (!iplb_valid_ccw(iplb) && !iplb_valid_fcp(iplb) && + !(iplb_valid_se(iplb) && s390_ipl_pv_check_comp(iplb) >= 0)) { env->regs[r1 + 1] = DIAG_308_RC_INVALID; goto out; } @@ -128,10 +135,15 @@ out: g_free(iplb); return; case DIAG308_STORE: + case DIAG308_PV_STORE: /* Get SE parms */ if (diag308_parm_check(env, r1, addr, ra, true)) { return; } - iplb = s390_ipl_get_iplb(); + if (subcode == DIAG308_PV_STORE) { + iplb = s390_ipl_get_iplb_secure(); + } else { + iplb = s390_ipl_get_iplb(); + } if (iplb) { cpu_physical_memory_write(addr, iplb, be32_to_cpu(iplb->len)); env->regs[r1 + 1] = DIAG_308_RC_OK; @@ -139,6 +151,16 @@ out: env->regs[r1 + 1] = DIAG_308_RC_NO_CONF; } return; + break; + case DIAG308_PV_START: /* SE start */ + iplb = s390_ipl_get_iplb_secure(); + if (!iplb_valid_se(iplb)) { + env->regs[r1 + 1] = DIAG_308_RC_NO_PV_CONF; + return; + } + + s390_ipl_reset_request(cs, S390_RESET_PV); + break; default: s390_program_interrupt(env, PGM_SPECIFICATION, ra); break;
For diag308 subcodes 8 - 10 we have a new ipib of type 5. The ipib holds the address and length of the secure execution header, as well as a list of guest components. Each component is a block of memory, for example kernel or initrd, which needs to be decrypted by the Ultravisor in order to run a protected VM. The secure execution header instructs the Ultravisor on how to handle the protected VM and its components. Subcodes 8 and 9 are similiar to 5 and 6 and subcode 10 will finally start the protected guest. Subcodes 8-10 are not valid in protected mode, we have to do a subcode 3 and then the 8 and 10 combination for a protected reboot. Signed-off-by: Janosch Frank <frankja@linux.ibm.com> --- hw/s390x/ipl.c | 48 ++++++++++++++++++++++++++++++++++++++++++--- hw/s390x/ipl.h | 33 +++++++++++++++++++++++++++++++ target/s390x/diag.c | 26 ++++++++++++++++++++++-- 3 files changed, 102 insertions(+), 5 deletions(-)