| Message ID | 20191129190541.30315-2-manivannan.sadhasivam@linaro.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | Improvements to IMX290 CMOS driver | expand |
Hi Manivannan, Thanks for the patchset. On Sat, Nov 30, 2019 at 12:35:37AM +0530, Manivannan Sadhasivam wrote: > The IMX290 sensor can output frames with 2/4 CSI2 data lanes. This commit > adds support for 2 lane mode in addition to the 4 lane and also > configuring the data lane settings in the driver based on system > configuration. > > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > --- > drivers/media/i2c/imx290.c | 130 ++++++++++++++++++++++++++++++++++--- > 1 file changed, 121 insertions(+), 9 deletions(-) > > diff --git a/drivers/media/i2c/imx290.c b/drivers/media/i2c/imx290.c > index f7678e5a5d87..1d49910937fb 100644 > --- a/drivers/media/i2c/imx290.c > +++ b/drivers/media/i2c/imx290.c > @@ -25,7 +25,18 @@ > #define IMX290_STANDBY 0x3000 > #define IMX290_REGHOLD 0x3001 > #define IMX290_XMSTA 0x3002 > +#define IMX290_FR_FDG_SEL 0x3009 > #define IMX290_GAIN 0x3014 > +#define IMX290_HMAX_LOW 0x301c > +#define IMX290_HMAX_HIGH 0x301d > +#define IMX290_PHY_LANE_NUM 0x3407 > +#define IMX290_CSI_LANE_MODE 0x3443 > + > +/* HMAX fields */ > +#define IMX290_HMAX_2_1920 0x1130 > +#define IMX290_HMAX_4_1920 0x0898 > +#define IMX290_HMAX_2_720 0x19C8 > +#define IMX290_HMAX_4_720 0x0CE4 > > #define IMX290_DEFAULT_LINK_FREQ 445500000 > > @@ -56,6 +67,7 @@ struct imx290 { > struct device *dev; > struct clk *xclk; > struct regmap *regmap; > + int nlanes; You're using u8 for another small (unsigned) integer later. How about u8 here? > > struct v4l2_subdev sd; > struct v4l2_fwnode_endpoint ep; > @@ -89,14 +101,11 @@ static const struct regmap_config imx290_regmap_config = { > > static const struct imx290_regval imx290_global_init_settings[] = { > { 0x3007, 0x00 }, > - { 0x3009, 0x00 }, > { 0x3018, 0x65 }, > { 0x3019, 0x04 }, > { 0x301a, 0x00 }, > - { 0x3443, 0x03 }, > { 0x3444, 0x20 }, > { 0x3445, 0x25 }, > - { 0x3407, 0x03 }, > { 0x303a, 0x0c }, > { 0x3040, 0x00 }, > { 0x3041, 0x00 }, > @@ -169,7 +178,6 @@ static const struct imx290_regval imx290_1080p_settings[] = { > { 0x3164, 0x1a }, > { 0x3480, 0x49 }, > /* data rate settings */ > - { 0x3009, 0x01 }, > { 0x3405, 0x10 }, > { 0x3446, 0x57 }, > { 0x3447, 0x00 }, > @@ -187,8 +195,6 @@ static const struct imx290_regval imx290_1080p_settings[] = { > { 0x3453, 0x00 }, > { 0x3454, 0x17 }, > { 0x3455, 0x00 }, > - { 0x301c, 0x98 }, > - { 0x301d, 0x08 }, > }; > > static const struct imx290_regval imx290_720p_settings[] = { > @@ -210,7 +216,6 @@ static const struct imx290_regval imx290_720p_settings[] = { > { 0x3164, 0x1a }, > { 0x3480, 0x49 }, > /* data rate settings */ > - { 0x3009, 0x01 }, > { 0x3405, 0x10 }, > { 0x3446, 0x4f }, > { 0x3447, 0x00 }, > @@ -228,8 +233,6 @@ static const struct imx290_regval imx290_720p_settings[] = { > { 0x3453, 0x00 }, > { 0x3454, 0x17 }, > { 0x3455, 0x00 }, > - { 0x301c, 0xe4 }, > - { 0x301d, 0x0c }, > }; > > static const struct imx290_regval imx290_10bit_settings[] = { > @@ -522,6 +525,25 @@ static int imx290_write_current_format(struct imx290 *imx290, > return 0; > } > > +static int imx290_set_hmax(struct imx290 *imx290, u32 val) > +{ > + int ret; > + > + ret = imx290_write_reg(imx290, IMX290_HMAX_LOW, (val & 0xff)); > + if (ret) { > + dev_err(imx290->dev, "Error setting HMAX register\n"); > + return ret; > + } > + > + ret = imx290_write_reg(imx290, IMX290_HMAX_HIGH, ((val >> 8) & 0xff)); > + if (ret) { > + dev_err(imx290->dev, "Error setting HMAX register\n"); > + return ret; > + } > + > + return 0; > +} > + > /* Start streaming */ > static int imx290_start_streaming(struct imx290 *imx290) > { > @@ -551,6 +573,40 @@ static int imx290_start_streaming(struct imx290 *imx290) > return ret; > } > > + switch (imx290->nlanes) { > + case 2: > + if (imx290->current_mode->width == 1920) { > + ret = imx290_set_hmax(imx290, IMX290_HMAX_2_1920); > + if (ret < 0) > + return ret; > + } else { > + ret = imx290_set_hmax(imx290, IMX290_HMAX_2_720); > + if (ret < 0) > + return ret; > + } > + > + break; > + case 4: > + if (imx290->current_mode->width == 1920) { > + ret = imx290_set_hmax(imx290, IMX290_HMAX_4_1920); > + if (ret < 0) > + return ret; > + } else { > + ret = imx290_set_hmax(imx290, IMX290_HMAX_4_720); > + if (ret < 0) > + return ret; > + } > + > + break; > + default: > + /* > + * We should never hit this since the data lane count is > + * validated in probe itself > + */ > + dev_err(imx290->dev, "Lane configuration not supported\n"); > + return -EINVAL; > + } > + > /* Apply customized values from user */ > ret = v4l2_ctrl_handler_setup(imx290->sd.ctrl_handler); > if (ret) { > @@ -607,6 +663,49 @@ static int imx290_get_regulators(struct device *dev, struct imx290 *imx290) > imx290->supplies); > } > > +static int imx290_set_data_lanes(struct imx290 *imx290) > +{ > + int ret = 0, laneval, frsel; > + > + switch (imx290->nlanes) { > + case 2: > + laneval = 0x01; > + frsel = 0x02; > + break; > + case 4: > + laneval = 0x03; > + frsel = 0x01; > + break; > + default: > + /* > + * We should never hit this since the data lane count is > + * validated in probe itself > + */ > + dev_err(imx290->dev, "Lane configuration not supported\n"); > + ret = -EINVAL; > + goto exit; > + } > + > + ret = imx290_write_reg(imx290, IMX290_PHY_LANE_NUM, laneval); > + if (ret) { > + dev_err(imx290->dev, "Error setting Physical Lane number register\n"); > + goto exit; > + } > + > + ret = imx290_write_reg(imx290, IMX290_CSI_LANE_MODE, laneval); > + if (ret) { > + dev_err(imx290->dev, "Error setting CSI Lane mode register\n"); > + goto exit; > + } > + > + ret = imx290_write_reg(imx290, IMX290_FR_FDG_SEL, frsel); > + if (ret) > + dev_err(imx290->dev, "Error setting FR/FDG SEL register\n"); > + > +exit: > + return ret; > +} > + > static int imx290_power_on(struct device *dev) > { > struct i2c_client *client = to_i2c_client(dev); > @@ -703,6 +802,16 @@ static int imx290_probe(struct i2c_client *client) > goto free_err; > } > > + /* Get number of data lanes */ > + imx290->nlanes = imx290->ep.bus.mipi_csi2.num_data_lanes; > + if (imx290->nlanes != 2 && imx290->nlanes != 4) { > + dev_err(dev, "Invalid data lanes: %d\n", imx290->nlanes); > + ret = -EINVAL; > + goto free_err; > + } > + > + dev_dbg(dev, "Using %u data lanes\n", imx290->nlanes); > + > if (!imx290->ep.nr_of_link_frequencies) { > dev_err(dev, "link-frequency property not found in DT\n"); > ret = -EINVAL; > @@ -822,6 +931,9 @@ static int imx290_probe(struct i2c_client *client) > goto free_entity; > } > > + /* Set data lane count */ > + imx290_set_data_lanes(imx290); The sensor is likely (but not necessarily) about to be powered off here. Wouldn't this also belong to be put to the power on sequence? > + > pm_runtime_set_active(dev); > pm_runtime_enable(dev); > pm_runtime_idle(dev);
Hi Sakari, On Tue, Dec 03, 2019 at 10:45:20AM +0200, Sakari Ailus wrote: > Hi Manivannan, > > Thanks for the patchset. > > On Sat, Nov 30, 2019 at 12:35:37AM +0530, Manivannan Sadhasivam wrote: > > The IMX290 sensor can output frames with 2/4 CSI2 data lanes. This commit > > adds support for 2 lane mode in addition to the 4 lane and also > > configuring the data lane settings in the driver based on system > > configuration. > > > > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > > --- > > drivers/media/i2c/imx290.c | 130 ++++++++++++++++++++++++++++++++++--- > > 1 file changed, 121 insertions(+), 9 deletions(-) > > > > diff --git a/drivers/media/i2c/imx290.c b/drivers/media/i2c/imx290.c > > index f7678e5a5d87..1d49910937fb 100644 > > --- a/drivers/media/i2c/imx290.c > > +++ b/drivers/media/i2c/imx290.c > > @@ -25,7 +25,18 @@ > > #define IMX290_STANDBY 0x3000 > > #define IMX290_REGHOLD 0x3001 > > #define IMX290_XMSTA 0x3002 > > +#define IMX290_FR_FDG_SEL 0x3009 > > #define IMX290_GAIN 0x3014 > > +#define IMX290_HMAX_LOW 0x301c > > +#define IMX290_HMAX_HIGH 0x301d > > +#define IMX290_PHY_LANE_NUM 0x3407 > > +#define IMX290_CSI_LANE_MODE 0x3443 > > + > > +/* HMAX fields */ > > +#define IMX290_HMAX_2_1920 0x1130 > > +#define IMX290_HMAX_4_1920 0x0898 > > +#define IMX290_HMAX_2_720 0x19C8 > > +#define IMX290_HMAX_4_720 0x0CE4 > > > > #define IMX290_DEFAULT_LINK_FREQ 445500000 > > > > @@ -56,6 +67,7 @@ struct imx290 { > > struct device *dev; > > struct clk *xclk; > > struct regmap *regmap; > > + int nlanes; > > You're using u8 for another small (unsigned) integer later. How about u8 > here? > Yeah, this is a left over. I was initially trying to use some error checking with this! Will change it to u8. > > > > struct v4l2_subdev sd; > > struct v4l2_fwnode_endpoint ep; > > @@ -89,14 +101,11 @@ static const struct regmap_config imx290_regmap_config = { > > > > static const struct imx290_regval imx290_global_init_settings[] = { > > { 0x3007, 0x00 }, > > - { 0x3009, 0x00 }, > > { 0x3018, 0x65 }, > > { 0x3019, 0x04 }, > > { 0x301a, 0x00 }, > > - { 0x3443, 0x03 }, > > { 0x3444, 0x20 }, > > { 0x3445, 0x25 }, > > - { 0x3407, 0x03 }, > > { 0x303a, 0x0c }, > > { 0x3040, 0x00 }, > > { 0x3041, 0x00 }, > > @@ -169,7 +178,6 @@ static const struct imx290_regval imx290_1080p_settings[] = { > > { 0x3164, 0x1a }, > > { 0x3480, 0x49 }, > > /* data rate settings */ > > - { 0x3009, 0x01 }, > > { 0x3405, 0x10 }, > > { 0x3446, 0x57 }, > > { 0x3447, 0x00 }, > > @@ -187,8 +195,6 @@ static const struct imx290_regval imx290_1080p_settings[] = { > > { 0x3453, 0x00 }, > > { 0x3454, 0x17 }, > > { 0x3455, 0x00 }, > > - { 0x301c, 0x98 }, > > - { 0x301d, 0x08 }, > > }; > > > > static const struct imx290_regval imx290_720p_settings[] = { > > @@ -210,7 +216,6 @@ static const struct imx290_regval imx290_720p_settings[] = { > > { 0x3164, 0x1a }, > > { 0x3480, 0x49 }, > > /* data rate settings */ > > - { 0x3009, 0x01 }, > > { 0x3405, 0x10 }, > > { 0x3446, 0x4f }, > > { 0x3447, 0x00 }, > > @@ -228,8 +233,6 @@ static const struct imx290_regval imx290_720p_settings[] = { > > { 0x3453, 0x00 }, > > { 0x3454, 0x17 }, > > { 0x3455, 0x00 }, > > - { 0x301c, 0xe4 }, > > - { 0x301d, 0x0c }, > > }; > > > > static const struct imx290_regval imx290_10bit_settings[] = { > > @@ -522,6 +525,25 @@ static int imx290_write_current_format(struct imx290 *imx290, > > return 0; > > } > > > > +static int imx290_set_hmax(struct imx290 *imx290, u32 val) > > +{ > > + int ret; > > + > > + ret = imx290_write_reg(imx290, IMX290_HMAX_LOW, (val & 0xff)); > > + if (ret) { > > + dev_err(imx290->dev, "Error setting HMAX register\n"); > > + return ret; > > + } > > + > > + ret = imx290_write_reg(imx290, IMX290_HMAX_HIGH, ((val >> 8) & 0xff)); > > + if (ret) { > > + dev_err(imx290->dev, "Error setting HMAX register\n"); > > + return ret; > > + } > > + > > + return 0; > > +} > > + > > /* Start streaming */ > > static int imx290_start_streaming(struct imx290 *imx290) > > { > > @@ -551,6 +573,40 @@ static int imx290_start_streaming(struct imx290 *imx290) > > return ret; > > } > > > > + switch (imx290->nlanes) { > > + case 2: > > + if (imx290->current_mode->width == 1920) { > > + ret = imx290_set_hmax(imx290, IMX290_HMAX_2_1920); > > + if (ret < 0) > > + return ret; > > + } else { > > + ret = imx290_set_hmax(imx290, IMX290_HMAX_2_720); > > + if (ret < 0) > > + return ret; > > + } > > + > > + break; > > + case 4: > > + if (imx290->current_mode->width == 1920) { > > + ret = imx290_set_hmax(imx290, IMX290_HMAX_4_1920); > > + if (ret < 0) > > + return ret; > > + } else { > > + ret = imx290_set_hmax(imx290, IMX290_HMAX_4_720); > > + if (ret < 0) > > + return ret; > > + } > > + > > + break; > > + default: > > + /* > > + * We should never hit this since the data lane count is > > + * validated in probe itself > > + */ > > + dev_err(imx290->dev, "Lane configuration not supported\n"); > > + return -EINVAL; > > + } > > + > > /* Apply customized values from user */ > > ret = v4l2_ctrl_handler_setup(imx290->sd.ctrl_handler); > > if (ret) { > > @@ -607,6 +663,49 @@ static int imx290_get_regulators(struct device *dev, struct imx290 *imx290) > > imx290->supplies); > > } > > > > +static int imx290_set_data_lanes(struct imx290 *imx290) > > +{ > > + int ret = 0, laneval, frsel; > > + > > + switch (imx290->nlanes) { > > + case 2: > > + laneval = 0x01; > > + frsel = 0x02; > > + break; > > + case 4: > > + laneval = 0x03; > > + frsel = 0x01; > > + break; > > + default: > > + /* > > + * We should never hit this since the data lane count is > > + * validated in probe itself > > + */ > > + dev_err(imx290->dev, "Lane configuration not supported\n"); > > + ret = -EINVAL; > > + goto exit; > > + } > > + > > + ret = imx290_write_reg(imx290, IMX290_PHY_LANE_NUM, laneval); > > + if (ret) { > > + dev_err(imx290->dev, "Error setting Physical Lane number register\n"); > > + goto exit; > > + } > > + > > + ret = imx290_write_reg(imx290, IMX290_CSI_LANE_MODE, laneval); > > + if (ret) { > > + dev_err(imx290->dev, "Error setting CSI Lane mode register\n"); > > + goto exit; > > + } > > + > > + ret = imx290_write_reg(imx290, IMX290_FR_FDG_SEL, frsel); > > + if (ret) > > + dev_err(imx290->dev, "Error setting FR/FDG SEL register\n"); > > + > > +exit: > > + return ret; > > +} > > + > > static int imx290_power_on(struct device *dev) > > { > > struct i2c_client *client = to_i2c_client(dev); > > @@ -703,6 +802,16 @@ static int imx290_probe(struct i2c_client *client) > > goto free_err; > > } > > > > + /* Get number of data lanes */ > > + imx290->nlanes = imx290->ep.bus.mipi_csi2.num_data_lanes; > > + if (imx290->nlanes != 2 && imx290->nlanes != 4) { > > + dev_err(dev, "Invalid data lanes: %d\n", imx290->nlanes); > > + ret = -EINVAL; > > + goto free_err; > > + } > > + > > + dev_dbg(dev, "Using %u data lanes\n", imx290->nlanes); > > + > > if (!imx290->ep.nr_of_link_frequencies) { > > dev_err(dev, "link-frequency property not found in DT\n"); > > ret = -EINVAL; > > @@ -822,6 +931,9 @@ static int imx290_probe(struct i2c_client *client) > > goto free_entity; > > } > > > > + /* Set data lane count */ > > + imx290_set_data_lanes(imx290); > > The sensor is likely (but not necessarily) about to be powered off here. > Wouldn't this also belong to be put to the power on sequence? > Agree, will add. Thanks, Mani > > + > > pm_runtime_set_active(dev); > > pm_runtime_enable(dev); > > pm_runtime_idle(dev); > > -- > Regards, > > Sakari Ailus
diff --git a/drivers/media/i2c/imx290.c b/drivers/media/i2c/imx290.c index f7678e5a5d87..1d49910937fb 100644 --- a/drivers/media/i2c/imx290.c +++ b/drivers/media/i2c/imx290.c @@ -25,7 +25,18 @@ #define IMX290_STANDBY 0x3000 #define IMX290_REGHOLD 0x3001 #define IMX290_XMSTA 0x3002 +#define IMX290_FR_FDG_SEL 0x3009 #define IMX290_GAIN 0x3014 +#define IMX290_HMAX_LOW 0x301c +#define IMX290_HMAX_HIGH 0x301d +#define IMX290_PHY_LANE_NUM 0x3407 +#define IMX290_CSI_LANE_MODE 0x3443 + +/* HMAX fields */ +#define IMX290_HMAX_2_1920 0x1130 +#define IMX290_HMAX_4_1920 0x0898 +#define IMX290_HMAX_2_720 0x19C8 +#define IMX290_HMAX_4_720 0x0CE4 #define IMX290_DEFAULT_LINK_FREQ 445500000 @@ -56,6 +67,7 @@ struct imx290 { struct device *dev; struct clk *xclk; struct regmap *regmap; + int nlanes; struct v4l2_subdev sd; struct v4l2_fwnode_endpoint ep; @@ -89,14 +101,11 @@ static const struct regmap_config imx290_regmap_config = { static const struct imx290_regval imx290_global_init_settings[] = { { 0x3007, 0x00 }, - { 0x3009, 0x00 }, { 0x3018, 0x65 }, { 0x3019, 0x04 }, { 0x301a, 0x00 }, - { 0x3443, 0x03 }, { 0x3444, 0x20 }, { 0x3445, 0x25 }, - { 0x3407, 0x03 }, { 0x303a, 0x0c }, { 0x3040, 0x00 }, { 0x3041, 0x00 }, @@ -169,7 +178,6 @@ static const struct imx290_regval imx290_1080p_settings[] = { { 0x3164, 0x1a }, { 0x3480, 0x49 }, /* data rate settings */ - { 0x3009, 0x01 }, { 0x3405, 0x10 }, { 0x3446, 0x57 }, { 0x3447, 0x00 }, @@ -187,8 +195,6 @@ static const struct imx290_regval imx290_1080p_settings[] = { { 0x3453, 0x00 }, { 0x3454, 0x17 }, { 0x3455, 0x00 }, - { 0x301c, 0x98 }, - { 0x301d, 0x08 }, }; static const struct imx290_regval imx290_720p_settings[] = { @@ -210,7 +216,6 @@ static const struct imx290_regval imx290_720p_settings[] = { { 0x3164, 0x1a }, { 0x3480, 0x49 }, /* data rate settings */ - { 0x3009, 0x01 }, { 0x3405, 0x10 }, { 0x3446, 0x4f }, { 0x3447, 0x00 }, @@ -228,8 +233,6 @@ static const struct imx290_regval imx290_720p_settings[] = { { 0x3453, 0x00 }, { 0x3454, 0x17 }, { 0x3455, 0x00 }, - { 0x301c, 0xe4 }, - { 0x301d, 0x0c }, }; static const struct imx290_regval imx290_10bit_settings[] = { @@ -522,6 +525,25 @@ static int imx290_write_current_format(struct imx290 *imx290, return 0; } +static int imx290_set_hmax(struct imx290 *imx290, u32 val) +{ + int ret; + + ret = imx290_write_reg(imx290, IMX290_HMAX_LOW, (val & 0xff)); + if (ret) { + dev_err(imx290->dev, "Error setting HMAX register\n"); + return ret; + } + + ret = imx290_write_reg(imx290, IMX290_HMAX_HIGH, ((val >> 8) & 0xff)); + if (ret) { + dev_err(imx290->dev, "Error setting HMAX register\n"); + return ret; + } + + return 0; +} + /* Start streaming */ static int imx290_start_streaming(struct imx290 *imx290) { @@ -551,6 +573,40 @@ static int imx290_start_streaming(struct imx290 *imx290) return ret; } + switch (imx290->nlanes) { + case 2: + if (imx290->current_mode->width == 1920) { + ret = imx290_set_hmax(imx290, IMX290_HMAX_2_1920); + if (ret < 0) + return ret; + } else { + ret = imx290_set_hmax(imx290, IMX290_HMAX_2_720); + if (ret < 0) + return ret; + } + + break; + case 4: + if (imx290->current_mode->width == 1920) { + ret = imx290_set_hmax(imx290, IMX290_HMAX_4_1920); + if (ret < 0) + return ret; + } else { + ret = imx290_set_hmax(imx290, IMX290_HMAX_4_720); + if (ret < 0) + return ret; + } + + break; + default: + /* + * We should never hit this since the data lane count is + * validated in probe itself + */ + dev_err(imx290->dev, "Lane configuration not supported\n"); + return -EINVAL; + } + /* Apply customized values from user */ ret = v4l2_ctrl_handler_setup(imx290->sd.ctrl_handler); if (ret) { @@ -607,6 +663,49 @@ static int imx290_get_regulators(struct device *dev, struct imx290 *imx290) imx290->supplies); } +static int imx290_set_data_lanes(struct imx290 *imx290) +{ + int ret = 0, laneval, frsel; + + switch (imx290->nlanes) { + case 2: + laneval = 0x01; + frsel = 0x02; + break; + case 4: + laneval = 0x03; + frsel = 0x01; + break; + default: + /* + * We should never hit this since the data lane count is + * validated in probe itself + */ + dev_err(imx290->dev, "Lane configuration not supported\n"); + ret = -EINVAL; + goto exit; + } + + ret = imx290_write_reg(imx290, IMX290_PHY_LANE_NUM, laneval); + if (ret) { + dev_err(imx290->dev, "Error setting Physical Lane number register\n"); + goto exit; + } + + ret = imx290_write_reg(imx290, IMX290_CSI_LANE_MODE, laneval); + if (ret) { + dev_err(imx290->dev, "Error setting CSI Lane mode register\n"); + goto exit; + } + + ret = imx290_write_reg(imx290, IMX290_FR_FDG_SEL, frsel); + if (ret) + dev_err(imx290->dev, "Error setting FR/FDG SEL register\n"); + +exit: + return ret; +} + static int imx290_power_on(struct device *dev) { struct i2c_client *client = to_i2c_client(dev); @@ -703,6 +802,16 @@ static int imx290_probe(struct i2c_client *client) goto free_err; } + /* Get number of data lanes */ + imx290->nlanes = imx290->ep.bus.mipi_csi2.num_data_lanes; + if (imx290->nlanes != 2 && imx290->nlanes != 4) { + dev_err(dev, "Invalid data lanes: %d\n", imx290->nlanes); + ret = -EINVAL; + goto free_err; + } + + dev_dbg(dev, "Using %u data lanes\n", imx290->nlanes); + if (!imx290->ep.nr_of_link_frequencies) { dev_err(dev, "link-frequency property not found in DT\n"); ret = -EINVAL; @@ -822,6 +931,9 @@ static int imx290_probe(struct i2c_client *client) goto free_entity; } + /* Set data lane count */ + imx290_set_data_lanes(imx290); + pm_runtime_set_active(dev); pm_runtime_enable(dev); pm_runtime_idle(dev);
The IMX290 sensor can output frames with 2/4 CSI2 data lanes. This commit adds support for 2 lane mode in addition to the 4 lane and also configuring the data lane settings in the driver based on system configuration. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> --- drivers/media/i2c/imx290.c | 130 ++++++++++++++++++++++++++++++++++--- 1 file changed, 121 insertions(+), 9 deletions(-)