new file mode 100644
@@ -0,0 +1,148 @@
+Atheros AR9331 built-in switch
+=============================
+
+It is a switch built-in to Atheros AR9331 WiSoC and addressable over internal
+MDIO bus. All PHYs are built-in as well.
+
+Required properties:
+
+ - compatible: should be: "qca,ar9331-switch"
+ - reg: Address on the MII bus for the switch.
+ - resets : Must contain an entry for each entry in reset-names.
+ - reset-names : Must include the following entries: "switch"
+ - interrupt-parent: Phandle to the parent interrupt controller
+ - interrupts: IRQ line for the switch
+ - interrupt-controller: Indicates the switch is itself an interrupt
+ controller. This is used for the PHY interrupts.
+ - #interrupt-cells: must be 1
+ - mdio: Container of PHY and devices on the switches MDIO bus.
+
+See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional
+required and optional properties.
+Examples:
+
+eth0: ethernet@19000000 {
+ compatible = "qca,ar9330-eth";
+ reg = <0x19000000 0x200>;
+ interrupts = <4>;
+
+ resets = <&rst 9>, <&rst 22>;
+ reset-names = "mac", "mdio";
+ clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_AHB>;
+ clock-names = "eth", "mdio";
+
+ phy-mode = "mii";
+ phy-handle = <&phy_port4>;
+};
+
+eth1: ethernet@1a000000 {
+ compatible = "qca,ar9330-eth";
+ reg = <0x1a000000 0x200>;
+ interrupts = <5>;
+ resets = <&rst 13>, <&rst 23>;
+ reset-names = "mac", "mdio";
+ clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_AHB>;
+ clock-names = "eth", "mdio";
+
+ phy-mode = "gmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch10: switch@10 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ compatible = "qca,ar9331-switch";
+ reg = <0x10>;
+ resets = <&rst 8>;
+ reset-names = "switch";
+
+ interrupt-parent = <&miscintc>;
+ interrupts = <12>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch_port0: port@0 {
+ reg = <0x0>;
+ label = "cpu";
+ ethernet = <ð1>;
+
+ phy-mode = "gmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ switch_port1: port@1 {
+ reg = <0x1>;
+ phy-handle = <&phy_port0>;
+ phy-mode = "internal";
+ };
+
+ switch_port2: port@2 {
+ reg = <0x2>;
+ phy-handle = <&phy_port1>;
+ phy-mode = "internal";
+ };
+
+ switch_port3: port@3 {
+ reg = <0x3>;
+ phy-handle = <&phy_port2>;
+ phy-mode = "internal";
+ };
+
+ switch_port4: port@4 {
+ reg = <0x4>;
+ phy-handle = <&phy_port3>;
+ phy-mode = "internal";
+ };
+ };
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ interrupt-parent = <&switch10>;
+
+ phy_port0: phy@0 {
+ reg = <0x0>;
+ interrupts = <0>;
+ };
+
+ phy_port1: phy@1 {
+ reg = <0x1>;
+ interrupts = <0>;
+ };
+
+ phy_port2: phy@2 {
+ reg = <0x2>;
+ interrupts = <0>;
+ };
+
+ phy_port3: phy@3 {
+ reg = <0x3>;
+ interrupts = <0>;
+ };
+
+ phy_port4: phy@4 {
+ reg = <0x4>;
+ interrupts = <0>;
+ };
+ };
+ };
+ };
+};
Atheros AR9331 has built-in 5 port switch. The switch can be configured to use all 5 or 4 ports. One of built-in PHYs can be used by first built-in ethernet controller or to be used directly by the switch over second ethernet controller. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> --- .../devicetree/bindings/net/dsa/ar9331.txt | 148 ++++++++++++++++++ 1 file changed, 148 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/dsa/ar9331.txt