| Message ID | 20200119163104.13274-8-samuel@sholland.org (mailing list archive) |
|---|---|
| State | Mainlined |
| Commit | 47ef030c3a796e07fec12c6981bbb46bcb258e2e |
| Headers | show |
| Series | [1/9] arm64: dts: allwinner: Enable button wakeup on Orange Pi PC2 | expand |
On Sun, Jan 19, 2020 at 10:31:03AM -0600, Samuel Holland wrote: > The output from the backlight regulator is labeled as "VBKLT" in the > schematic. Using the equation and resistor values from the schematic, > the output is approximately 18V, not 3.3V. Since the regulator in use > (SS6640STR) is a boost regulator powered by PS (battery or AC input), > which are both >3.3V, the output could not be 3.3V anyway. > > Signed-off-by: Samuel Holland <samuel@sholland.org> Applied, thanks! Maxime
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts index 3e762f93671a..96434fdeb5c0 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts @@ -21,22 +21,13 @@ ethernet0 = &rtl8723cs; }; - vdd_bl: regulator@0 { - compatible = "regulator-fixed"; - regulator-name = "bl-3v3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */ - enable-active-high; - }; - backlight: backlight { compatible = "pwm-backlight"; pwms = <&pwm 0 50000 0>; brightness-levels = <0 5 10 15 20 30 40 55 70 85 100>; default-brightness-level = <2>; enable-gpios = <&pio 3 23 GPIO_ACTIVE_HIGH>; /* PD23 */ - power-supply = <&vdd_bl>; + power-supply = <®_vbklt>; }; chosen { @@ -57,6 +48,15 @@ }; }; + reg_vbklt: vbklt { + compatible = "regulator-fixed"; + regulator-name = "vbklt"; + regulator-min-microvolt = <18000000>; + regulator-max-microvolt = <18000000>; + gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */ + enable-active-high; + }; + wifi_pwrseq: wifi_pwrseq { compatible = "mmc-pwrseq-simple"; reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
The output from the backlight regulator is labeled as "VBKLT" in the schematic. Using the equation and resistor values from the schematic, the output is approximately 18V, not 3.3V. Since the regulator in use (SS6640STR) is a boost regulator powered by PS (battery or AC input), which are both >3.3V, the output could not be 3.3V anyway. Signed-off-by: Samuel Holland <samuel@sholland.org> --- .../dts/allwinner/sun50i-a64-pinebook.dts | 20 +++++++++---------- 1 file changed, 10 insertions(+), 10 deletions(-)