new file mode 100644
@@ -0,0 +1,80 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/serial/st,stm32-uart.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+maintainers:
+ - Erwan Le Ray <erwan.leray@st.com>
+
+title: STMicroelectronics STM32 USART bindings
+
+allOf:
+ - $ref: rs485.yaml
+
+properties:
+ compatible:
+ enum:
+ - st,stm32-uart
+ - st,stm32f7-uart
+ - st,stm32h7-uart
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+ label:
+ description: label associated with this uart
+
+ st,hw-flow-ctrl:
+ description: enable hardware flow control
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ dmas:
+ minItems: 1
+ maxItems: 2
+
+ dma-names:
+ items:
+ enum: [ rx, tx ]
+ minItems: 1
+ maxItems: 2
+
+ wakeup-source: true
+
+ rs485-rts-delay: true
+ rs485-rts-active-low: true
+ linux,rs485-enabled-at-boot-time: true
+ rs485-rx-during-tx: true
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/stm32mp1-clks.h>
+ usart1: serial@40011000 {
+ compatible = "st,stm32-uart";
+ reg = <0x40011000 0x400>;
+ interrupts = <37>;
+ clocks = <&rcc 0 164>;
+ dmas = <&dma2 2 4 0x414 0x0>,
+ <&dma2 7 4 0x414 0x0>;
+ dma-names = "rx", "tx";
+ rs485-rts-active-low;
+ };
+
+...
deleted file mode 100644
@@ -1,57 +0,0 @@
-* STMicroelectronics STM32 USART
-
-Required properties:
-- compatible: can be either:
- - "st,stm32-uart",
- - "st,stm32f7-uart",
- - "st,stm32h7-uart".
- depending is compatible with stm32(f4), stm32f7 or stm32h7.
-- reg: The address and length of the peripheral registers space
-- interrupts:
- - The interrupt line for the USART instance,
- - An optional wake-up interrupt.
-- clocks: The input clock of the USART instance
-
-Optional properties:
-- resets: Must contain the phandle to the reset controller.
-- pinctrl: The reference on the pins configuration
-- st,hw-flow-ctrl: bool flag to enable hardware flow control.
-- rs485-rts-delay, rs485-rx-during-tx, rs485-rts-active-low,
- linux,rs485-enabled-at-boot-time: see rs485.txt.
-- dmas: phandle(s) to DMA controller node(s). Refer to stm32-dma.txt
-- dma-names: "rx" and/or "tx"
-- wakeup-source: bool flag to indicate this device has wakeup capabilities
-- interrupt-names, if optional wake-up interrupt is used, should be:
- - "event": the name for the interrupt line of the USART instance
- - "wakeup" the name for the optional wake-up interrupt
-
-
-Examples:
-usart4: serial@40004c00 {
- compatible = "st,stm32-uart";
- reg = <0x40004c00 0x400>;
- interrupts = <52>;
- clocks = <&clk_pclk1>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usart4>;
-};
-
-usart2: serial@40004400 {
- compatible = "st,stm32-uart";
- reg = <0x40004400 0x400>;
- interrupts = <38>;
- clocks = <&clk_pclk1>;
- st,hw-flow-ctrl;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usart2 &pinctrl_usart2_rtscts>;
-};
-
-usart1: serial@40011000 {
- compatible = "st,stm32-uart";
- reg = <0x40011000 0x400>;
- interrupts = <37>;
- clocks = <&rcc 0 164>;
- dmas = <&dma2 2 4 0x414 0x0>,
- <&dma2 7 4 0x414 0x0>;
- dma-names = "rx", "tx";
-};
Convert STM32 UART bindings to json-schema. Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com> --- .../devicetree/bindings/serial/st,stm32-uart.yaml | 80 ++++++++++++++++++++++ .../devicetree/bindings/serial/st,stm32-usart.txt | 57 --------------- 2 files changed, 80 insertions(+), 57 deletions(-) create mode 100644 Documentation/devicetree/bindings/serial/st,stm32-uart.yaml delete mode 100644 Documentation/devicetree/bindings/serial/st,stm32-usart.txt