| Message ID | 1568983997-20004-3-git-send-email-cchiluve@codeaurora.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | ADD interconnect support for Qualcomm DWC3 driver | expand |
Hi Chandana, On Fri, Sep 20, 2019 at 06:23:16PM +0530, cchiluve wrote: > From: Chandana Kishori Chiluveru <cchiluve@codeaurora.org> > > Add interconnect support in dwc3-qcom driver to vote for bus > bandwidth. > > This requires for two different paths - from USB master to > DDR slave. The other is from APPS master to USB slave. > > Signed-off-by: Chandana Kishori Chiluveru <cchiluve@codeaurora.org> > --- > drivers/usb/dwc3/dwc3-qcom.c | 145 ++++++++++++++++++++++++++++++++++++++++++- > 1 file changed, 143 insertions(+), 2 deletions(-) > > diff --git a/drivers/usb/dwc3/dwc3-qcom.c b/drivers/usb/dwc3/dwc3-qcom.c > index 184df4d..3a540f7 100644 > --- a/drivers/usb/dwc3/dwc3-qcom.c > +++ b/drivers/usb/dwc3/dwc3-qcom.c > @@ -12,6 +12,7 @@ > #include <linux/module.h> > #include <linux/kernel.h> > #include <linux/extcon.h> > +#include <linux/interconnect.h> > #include <linux/of_platform.h> > #include <linux/platform_device.h> > #include <linux/phy/phy.h> > @@ -59,8 +60,13 @@ struct dwc3_qcom { > enum usb_dr_mode mode; > bool is_suspended; > bool pm_suspended; > + struct icc_path *usb_ddr_icc_path; > + struct icc_path *apps_usb_icc_path; > }; > > +static int dwc3_qcom_interconnect_enable(struct dwc3_qcom *qcom); > +static int dwc3_qcom_interconnect_disable(struct dwc3_qcom *qcom); > + > static inline void dwc3_qcom_setbits(void __iomem *base, u32 offset, u32 val) > { > u32 reg; > @@ -222,7 +228,7 @@ static void dwc3_qcom_enable_interrupts(struct dwc3_qcom *qcom) > static int dwc3_qcom_suspend(struct dwc3_qcom *qcom) > { > u32 val; > - int i; > + int i, ret; > > if (qcom->is_suspended) > return 0; > @@ -234,6 +240,10 @@ static int dwc3_qcom_suspend(struct dwc3_qcom *qcom) > for (i = qcom->num_clocks - 1; i >= 0; i--) > clk_disable_unprepare(qcom->clks[i]); > > + ret = dwc3_qcom_interconnect_disable(qcom); > + if (ret) > + dev_warn(qcom->dev, "failed to disable interconnect %d\n", ret); > + > qcom->is_suspended = true; > dwc3_qcom_enable_interrupts(qcom); > > @@ -259,6 +269,10 @@ static int dwc3_qcom_resume(struct dwc3_qcom *qcom) > } > } > > + ret = dwc3_qcom_interconnect_enable(qcom); > + if (ret) > + dev_warn(qcom->dev, "failed to enable interconnect %d\n", ret); > + > /* Clear existing events from PHY related to L2 in/out */ > dwc3_qcom_setbits(qcom->qscratch_base, PWR_EVNT_IRQ_STAT_REG, > PWR_EVNT_LPM_IN_L2_MASK | PWR_EVNT_LPM_OUT_L2_MASK); > @@ -268,6 +282,124 @@ static int dwc3_qcom_resume(struct dwc3_qcom *qcom) > return 0; > } > > +/* Interconnect path bandwidths in MBps */ > +#define USB_MEMORY_AVG_HS_BW MBps_to_icc(240) > +#define USB_MEMORY_PEAK_HS_BW MBps_to_icc(700) > +#define USB_MEMORY_AVG_SS_BW MBps_to_icc(1000) > +#define USB_MEMORY_PEAK_SS_BW MBps_to_icc(2500) > +#define APPS_USB_AVG_BW 0 > +#define APPS_USB_PEAK_BW MBps_to_icc(40) typically constants are defined before the function and struct definitions, I'd suggest to move this up, after the other constant definitions. > +/** > + * dwc3_qcom_interconnect_init() - Initialize the interconnect > + * @qcom: Pointer to the concerned usb core. > + * > + */ > +static int dwc3_qcom_interconnect_init(struct dwc3_qcom *qcom) > +{ > + struct device *dev = qcom->dev; > + struct dwc3 *dwc; The variable is not used, remove it. > + int ret; > + > + if (!device_is_bound(&qcom->dwc3->dev)) { > + dev_err(qcom->dev, "device is not bound\n"); An error message seems very harsh for a deferred probe. I'd say remove the logging altogether ("git grep -B3 'return -EPROBE_DEFER'" shows that there's rarely a specific message logged when the probe is deferred), if you really really want it downgrade it to dev_dbg() or dev_info(). > + return -EPROBE_DEFER; > + } > + > + qcom->usb_ddr_icc_path = of_icc_get(dev, "usb-ddr"); > + if (IS_ERR(qcom->usb_ddr_icc_path)) { > + dev_err(dev, "Error: (%ld) failed getting usb-ddr path\n", > + PTR_ERR(qcom->usb_ddr_icc_path)); > + return PTR_ERR(qcom->usb_ddr_icc_path); > + } > + > + qcom->apps_usb_icc_path = of_icc_get(dev, "apps-usb"); > + if (IS_ERR(qcom->apps_usb_icc_path)) { > + dev_err(dev, "Error: (%ld) failed getting apps-usb path\n", > + PTR_ERR(qcom->apps_usb_icc_path)); > + return PTR_ERR(qcom->apps_usb_icc_path); > + } > + > + ret = dwc3_qcom_interconnect_enable(qcom); > + if (ret) { > + dev_err(dev, "failed to enable interconnect: %d\n", ret); > + return ret; > + } > + > + return 0; > +} > + > +/** > + * dwc3_qcom_interconnect_exit() - Release interconnect path handles > + * @qcom: Pointer to the concerned usb core. > + * > + * This function is used to release interconnect path handle. > + */ > +static void dwc3_qcom_interconnect_exit(struct dwc3_qcom *qcom) > +{ > + icc_put(qcom->usb_ddr_icc_path); > + icc_put(qcom->apps_usb_icc_path); > +} > + > +/* Currently we only use bandwidth level, so just "enable" interconnects */ > +static int dwc3_qcom_interconnect_enable(struct dwc3_qcom *qcom) > +{ > + struct dwc3 *dwc = platform_get_drvdata(qcom->dwc3); > + int ret; > + > + if (dwc->maximum_speed == USB_SPEED_SUPER) { > + ret = icc_set_bw(qcom->usb_ddr_icc_path, > + USB_MEMORY_AVG_SS_BW, USB_MEMORY_PEAK_SS_BW); > + if (ret) > + return ret; > + } else { > + ret = icc_set_bw(qcom->usb_ddr_icc_path, > + USB_MEMORY_AVG_HS_BW, USB_MEMORY_PEAK_HS_BW); > + if (ret) > + return ret; Since the error check is the same for high speed and super speed it can be moved outside of the branch. > + } > + > + ret = icc_set_bw(qcom->apps_usb_icc_path, > + APPS_USB_AVG_BW, APPS_USB_PEAK_BW); > + if (ret) > + goto err_disable_mem_path; > + > + return 0; > + > +err_disable_mem_path: > + icc_set_bw(qcom->usb_ddr_icc_path, 0, 0); > + > + return ret; I'm not convinced the use of goto simplifies the code in this case. It could just be: if (ret) icc_set_bw(qcom->usb_ddr_icc_path, 0, 0); return ret; > +} > + > +/* To disable an interconnect, we just set its bandwidth to 0 */ > +static int dwc3_qcom_interconnect_disable(struct dwc3_qcom *qcom) > +{ > + struct dwc3 *dwc = platform_get_drvdata(qcom->dwc3); > + int ret; > + > + ret = icc_set_bw(qcom->usb_ddr_icc_path, 0, 0); > + if (ret) > + return ret; > + > + ret = icc_set_bw(qcom->apps_usb_icc_path, 0, 0); > + if (ret) > + goto err_reenable_memory_path; > + > + return 0; > + > + /* Re-enable things in the event of an error */ > +err_reenable_memory_path: > + if (dwc->maximum_speed == USB_SPEED_SUPER) > + icc_set_bw(qcom->usb_ddr_icc_path, > + USB_MEMORY_AVG_SS_BW, USB_MEMORY_PEAK_SS_BW); > + else > + icc_set_bw(qcom->usb_ddr_icc_path, > + USB_MEMORY_AVG_HS_BW, USB_MEMORY_PEAK_HS_BW); > + > + return ret; > +} > + > static irqreturn_t qcom_dwc3_resume_irq(int irq, void *data) > { > struct dwc3_qcom *qcom = data; > @@ -494,6 +626,12 @@ static int dwc3_qcom_probe(struct platform_device *pdev) > goto depopulate; > } > > + ret = dwc3_qcom_interconnect_init(qcom); > + if (ret) { > + dev_err(dev, "failed to init interconnect: %d\n", ret); Not sure if this message is really needed, dwc3_qcom_interconnect_init() logs a message in all error paths (except maybe for -EPROBE_DEFER in the future). At the very least this message should be omitted for -EPROBE_DEFER.
diff --git a/drivers/usb/dwc3/dwc3-qcom.c b/drivers/usb/dwc3/dwc3-qcom.c index 184df4d..3a540f7 100644 --- a/drivers/usb/dwc3/dwc3-qcom.c +++ b/drivers/usb/dwc3/dwc3-qcom.c @@ -12,6 +12,7 @@ #include <linux/module.h> #include <linux/kernel.h> #include <linux/extcon.h> +#include <linux/interconnect.h> #include <linux/of_platform.h> #include <linux/platform_device.h> #include <linux/phy/phy.h> @@ -59,8 +60,13 @@ struct dwc3_qcom { enum usb_dr_mode mode; bool is_suspended; bool pm_suspended; + struct icc_path *usb_ddr_icc_path; + struct icc_path *apps_usb_icc_path; }; +static int dwc3_qcom_interconnect_enable(struct dwc3_qcom *qcom); +static int dwc3_qcom_interconnect_disable(struct dwc3_qcom *qcom); + static inline void dwc3_qcom_setbits(void __iomem *base, u32 offset, u32 val) { u32 reg; @@ -222,7 +228,7 @@ static void dwc3_qcom_enable_interrupts(struct dwc3_qcom *qcom) static int dwc3_qcom_suspend(struct dwc3_qcom *qcom) { u32 val; - int i; + int i, ret; if (qcom->is_suspended) return 0; @@ -234,6 +240,10 @@ static int dwc3_qcom_suspend(struct dwc3_qcom *qcom) for (i = qcom->num_clocks - 1; i >= 0; i--) clk_disable_unprepare(qcom->clks[i]); + ret = dwc3_qcom_interconnect_disable(qcom); + if (ret) + dev_warn(qcom->dev, "failed to disable interconnect %d\n", ret); + qcom->is_suspended = true; dwc3_qcom_enable_interrupts(qcom); @@ -259,6 +269,10 @@ static int dwc3_qcom_resume(struct dwc3_qcom *qcom) } } + ret = dwc3_qcom_interconnect_enable(qcom); + if (ret) + dev_warn(qcom->dev, "failed to enable interconnect %d\n", ret); + /* Clear existing events from PHY related to L2 in/out */ dwc3_qcom_setbits(qcom->qscratch_base, PWR_EVNT_IRQ_STAT_REG, PWR_EVNT_LPM_IN_L2_MASK | PWR_EVNT_LPM_OUT_L2_MASK); @@ -268,6 +282,124 @@ static int dwc3_qcom_resume(struct dwc3_qcom *qcom) return 0; } +/* Interconnect path bandwidths in MBps */ +#define USB_MEMORY_AVG_HS_BW MBps_to_icc(240) +#define USB_MEMORY_PEAK_HS_BW MBps_to_icc(700) +#define USB_MEMORY_AVG_SS_BW MBps_to_icc(1000) +#define USB_MEMORY_PEAK_SS_BW MBps_to_icc(2500) +#define APPS_USB_AVG_BW 0 +#define APPS_USB_PEAK_BW MBps_to_icc(40) + +/** + * dwc3_qcom_interconnect_init() - Initialize the interconnect + * @qcom: Pointer to the concerned usb core. + * + */ +static int dwc3_qcom_interconnect_init(struct dwc3_qcom *qcom) +{ + struct device *dev = qcom->dev; + struct dwc3 *dwc; + int ret; + + if (!device_is_bound(&qcom->dwc3->dev)) { + dev_err(qcom->dev, "device is not bound\n"); + return -EPROBE_DEFER; + } + + qcom->usb_ddr_icc_path = of_icc_get(dev, "usb-ddr"); + if (IS_ERR(qcom->usb_ddr_icc_path)) { + dev_err(dev, "Error: (%ld) failed getting usb-ddr path\n", + PTR_ERR(qcom->usb_ddr_icc_path)); + return PTR_ERR(qcom->usb_ddr_icc_path); + } + + qcom->apps_usb_icc_path = of_icc_get(dev, "apps-usb"); + if (IS_ERR(qcom->apps_usb_icc_path)) { + dev_err(dev, "Error: (%ld) failed getting apps-usb path\n", + PTR_ERR(qcom->apps_usb_icc_path)); + return PTR_ERR(qcom->apps_usb_icc_path); + } + + ret = dwc3_qcom_interconnect_enable(qcom); + if (ret) { + dev_err(dev, "failed to enable interconnect: %d\n", ret); + return ret; + } + + return 0; +} + +/** + * dwc3_qcom_interconnect_exit() - Release interconnect path handles + * @qcom: Pointer to the concerned usb core. + * + * This function is used to release interconnect path handle. + */ +static void dwc3_qcom_interconnect_exit(struct dwc3_qcom *qcom) +{ + icc_put(qcom->usb_ddr_icc_path); + icc_put(qcom->apps_usb_icc_path); +} + +/* Currently we only use bandwidth level, so just "enable" interconnects */ +static int dwc3_qcom_interconnect_enable(struct dwc3_qcom *qcom) +{ + struct dwc3 *dwc = platform_get_drvdata(qcom->dwc3); + int ret; + + if (dwc->maximum_speed == USB_SPEED_SUPER) { + ret = icc_set_bw(qcom->usb_ddr_icc_path, + USB_MEMORY_AVG_SS_BW, USB_MEMORY_PEAK_SS_BW); + if (ret) + return ret; + } else { + ret = icc_set_bw(qcom->usb_ddr_icc_path, + USB_MEMORY_AVG_HS_BW, USB_MEMORY_PEAK_HS_BW); + if (ret) + return ret; + } + + ret = icc_set_bw(qcom->apps_usb_icc_path, + APPS_USB_AVG_BW, APPS_USB_PEAK_BW); + if (ret) + goto err_disable_mem_path; + + return 0; + +err_disable_mem_path: + icc_set_bw(qcom->usb_ddr_icc_path, 0, 0); + + return ret; +} + +/* To disable an interconnect, we just set its bandwidth to 0 */ +static int dwc3_qcom_interconnect_disable(struct dwc3_qcom *qcom) +{ + struct dwc3 *dwc = platform_get_drvdata(qcom->dwc3); + int ret; + + ret = icc_set_bw(qcom->usb_ddr_icc_path, 0, 0); + if (ret) + return ret; + + ret = icc_set_bw(qcom->apps_usb_icc_path, 0, 0); + if (ret) + goto err_reenable_memory_path; + + return 0; + + /* Re-enable things in the event of an error */ +err_reenable_memory_path: + if (dwc->maximum_speed == USB_SPEED_SUPER) + icc_set_bw(qcom->usb_ddr_icc_path, + USB_MEMORY_AVG_SS_BW, USB_MEMORY_PEAK_SS_BW); + else + icc_set_bw(qcom->usb_ddr_icc_path, + USB_MEMORY_AVG_HS_BW, USB_MEMORY_PEAK_HS_BW); + + return ret; +} + static irqreturn_t qcom_dwc3_resume_irq(int irq, void *data) { struct dwc3_qcom *qcom = data; @@ -494,6 +626,12 @@ static int dwc3_qcom_probe(struct platform_device *pdev) goto depopulate; } + ret = dwc3_qcom_interconnect_init(qcom); + if (ret) { + dev_err(dev, "failed to init interconnect: %d\n", ret); + goto depopulate; + } + qcom->mode = usb_get_dr_mode(&qcom->dwc3->dev); /* enable vbus override for device mode */ @@ -503,7 +641,7 @@ static int dwc3_qcom_probe(struct platform_device *pdev) /* register extcon to override sw_vbus on Vbus change later */ ret = dwc3_qcom_register_extcon(qcom); if (ret) - goto depopulate; + goto interconnect_exit; device_init_wakeup(&pdev->dev, 1); qcom->is_suspended = false; @@ -513,6 +651,8 @@ static int dwc3_qcom_probe(struct platform_device *pdev) return 0; +interconnect_exit: + dwc3_qcom_interconnect_exit(qcom); depopulate: of_platform_depopulate(&pdev->dev); clk_disable: @@ -540,6 +680,7 @@ static int dwc3_qcom_remove(struct platform_device *pdev) } qcom->num_clocks = 0; + dwc3_qcom_interconnect_exit(qcom); reset_control_assert(qcom->resets); pm_runtime_allow(dev);