@@ -28,6 +28,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopc-t4.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-m4.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-neo4.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-orangepi.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-pinebook-pro.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-puma-haikou.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc-mezzanine.dtb
new file mode 100644
@@ -0,0 +1,1096 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2017 Fuzhou Rockchip Electronics Co., Ltd.
+ * Copyright (c) 2018 Akash Gajjar <Akash_Gajjar@mentor.com>
+ * Copyright (c) 2020 Tobias Schramm <t.schramm@manjaro.org>
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/usb/pd.h>
+#include <dt-bindings/leds/common.h>
+#include "rk3399.dtsi"
+#include "rk3399-opp.dtsi"
+
+/ {
+ model = "Pine64 Pinebook Pro";
+ compatible = "pine64,pinebook-pro", "rockchip,rk3399";
+
+ chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ backlight: edp-backlight {
+ compatible = "pwm-backlight";
+ power-supply = <&vcc_12v>;
+ pwms = <&pwm0 0 740740 0>;
+ };
+
+ edp_panel: edp-panel {
+ compatible = "boe,nv140fhmn49";
+ backlight = <&backlight>;
+ enable-gpios = <&gpio1 RK_PA0 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&panel_en_gpio>;
+ power-supply = <&vcc3v3_panel>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ panel_in_edp: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&edp_out_panel>;
+ };
+ };
+ };
+ };
+
+ /*
+ * Use separate nodes for gpio-keys to allow for selective deactivation
+ * of wakeup sources via sysfs without disabling the whole key
+ */
+ gpio-key-lid {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&lidbtn_gpio>;
+
+ lid {
+ debounce-interval = <20>;
+ gpios = <&gpio1 RK_PA1 GPIO_ACTIVE_LOW>;
+ label = "Lid";
+ linux,code = <SW_LID>;
+ linux,input-type = <EV_SW>;
+ wakeup-event-action = <EV_ACT_DEASSERTED>;
+ wakeup-source;
+ };
+ };
+
+ gpio-key-power {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwrbtn_gpio>;
+
+ power {
+ debounce-interval = <20>;
+ gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
+ label = "Power";
+ linux,code = <KEY_POWER>;
+ wakeup-source;
+ };
+ };
+
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwrled_gpio &slpled_gpio>;
+
+ green-led {
+ color = <LED_COLOR_ID_GREEN>;
+ default-state = "on";
+ function = LED_FUNCTION_POWER;
+ gpios = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
+ label = "green:power";
+ };
+
+ red-led {
+ color = <LED_COLOR_ID_RED>;
+ default-state = "off";
+ function = LED_FUNCTION_STANDBY;
+ gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
+ label = "red:standby";
+ panic-indicator;
+ retain-state-suspended;
+ };
+ };
+
+ /* Power sequence for SDIO WiFi module */
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rk808 1>;
+ clock-names = "ext_clock";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_enable_h_gpio>;
+ post-power-on-delay-ms = <100>;
+ power-off-delay-us = <500000>;
+
+ /* WL_REG_ON on module */
+ reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
+ };
+
+ /* Audio components */
+ es8316-sound {
+ compatible = "simple-audio-card";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hp_det_gpio>;
+ simple-audio-card,name = "rockchip,es8316-codec";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,mclk-fs = <256>;
+
+ simple-audio-card,widgets =
+ "Microphone", "Mic Jack",
+ "Headphone", "Headphones",
+ "Speaker", "Speaker";
+ simple-audio-card,routing =
+ "MIC1", "Mic Jack",
+ "Headphones", "HPOL",
+ "Headphones", "HPOR",
+ "Speaker Amplifier INL", "HPOL",
+ "Speaker Amplifier INR", "HPOR",
+ "Speaker", "Speaker Amplifier OUTL",
+ "Speaker", "Speaker Amplifier OUTR";
+
+ simple-audio-card,hp-det-gpio = <&gpio0 RK_PB0 GPIO_ACTIVE_LOW>;
+ simple-audio-card,aux-devs = <&speaker_amp>;
+ simple-audio-card,pin-switches = "Speaker";
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s1>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&es8316>;
+ };
+ };
+
+ speaker_amp: speaker-amplifier {
+ compatible = "simple-audio-amplifier";
+ enable-gpios = <&gpio4 RK_PD3 GPIO_ACTIVE_HIGH>;
+ sound-name-prefix = "Speaker Amplifier";
+ VCC-supply = <&pa_5v>;
+ };
+
+ /* Power tree */
+ /* Root power source */
+ vcc_sysin: vcc-sysin {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc_sysin";
+ };
+
+ /* Regulators supplied by vcc_sysin */
+ /* LCD backlight supply */
+ vcc_12v: vcc-12v {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-name = "vcc_12v";
+ vin-supply = <&vcc_sysin>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ /* Main 3.3 V supply */
+ vcc3v3_sys: wifi_bat: vcc3v3-sys {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3_sys";
+ vin-supply = <&vcc_sysin>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ /* 5 V USB power supply */
+ vcc5v0_usb: pa_5v: vcc5v0-usb-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio1 RK_PB5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwr_5v_gpio>;
+ regulator-always-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-name = "vcc5v0_usb";
+ vin-supply = <&vcc_sysin>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ /* RK3399 logic supply */
+ vdd_log: vdd-log {
+ compatible = "pwm-regulator";
+ pwms = <&pwm2 0 25000 1>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd_log";
+ vin-supply = <&vcc_sysin>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ /* Regulators supplied by vcc3v3_sys */
+ /* 0.9 V supply, always on */
+ vcc_0v9: vcc-0v9 {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vcc_0v9";
+ vin-supply = <&vcc3v3_sys>;
+ };
+
+ /* S3 1.8 V supply, switched by vcc1v8_s3 */
+ vcca1v8_s3: vcc1v8-s3 {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcca1v8_s3";
+ vin-supply = <&vcc3v3_sys>;
+ };
+
+ /* micro SD card power */
+ vcc3v0_sd: vcc3v0-sd {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 RK_PA1 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0_pwr_h_gpio>;
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc3v0_sd";
+ vin-supply = <&vcc3v3_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ /* LCD panel power, called VCC3V3_S0 in schematic */
+ vcc3v3_panel: vcc3v3-panel {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio1 RK_PC6 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdvcc_en_gpio>;
+ regulator-always-on;
+ regulator-enable-ramp-delay = <100000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3_panel";
+ vin-supply = <&vcc3v3_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ /* M.2 adapter power, switched by vcc1v8_s3 */
+ vcc3v3_ssd: vcc3v3-ssd {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3_ssd";
+ vin-supply = <&vcc3v3_sys>;
+ };
+
+ /* Regulators supplied by vcc5v0_usb */
+ /* USB 3 port power supply regulator */
+ vcc5v0_otg: vcc5v0-otg {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v0_host_en_gpio>;
+ regulator-always-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-name = "vcc5v0_otg";
+ vin-supply = <&vcc5v0_usb>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ /* Regulators supplied by vcc5v0_usb */
+ /* Type C port power supply regulator */
+ vbus_5vout: vbus_typec: vbus-5vout {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio1 RK_PA3 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v0_typec0_en_gpio>;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-name = "vbus_5vout";
+ vin-supply = <&vcc5v0_usb>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ /* Regulators supplied by vcc_1v8 */
+ /* Primary 0.9 V LDO */
+ vcca0v9_s3: vcca0v9-s3 {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-name = "vcc0v9_s3";
+ vin-supply = <&vcc_1v8>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ mains_charger: dc-charger {
+ compatible = "gpio-charger";
+ charger-type = "mains";
+ gpios = <&gpio4 RK_PD0 GPIO_ACTIVE_LOW>;
+
+ /* Also triggered by USB charger */
+ pinctrl-names = "default";
+ pinctrl-0 = <&dc_det_gpio>;
+ };
+};
+
+&cdn_dp {
+ status = "okay";
+};
+
+&cpu_b0 {
+ cpu-supply = <&vdd_cpu_b>;
+};
+
+&cpu_b1 {
+ cpu-supply = <&vdd_cpu_b>;
+};
+
+&cpu_l0 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l1 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l2 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l3 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&edp {
+ force-hpd;
+ pinctrl-names = "default";
+ pinctrl-0 = <&edp_hpd>;
+ status = "okay";
+
+ ports {
+ edp_out: port@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ edp_out_panel: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&panel_in_edp>;
+ };
+ };
+ };
+};
+
+&emmc_phy {
+ status = "okay";
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu>;
+ status = "okay";
+};
+
+&hdmi_sound {
+ status = "okay";
+};
+
+&i2c0 {
+ clock-frequency = <400000>;
+ i2c-scl-falling-time-ns = <4>;
+ i2c-scl-rising-time-ns = <168>;
+ status = "okay";
+
+ rk808: pmic@1b {
+ compatible = "rockchip,rk808";
+ reg = <0x1b>;
+ #clock-cells = <1>;
+ clock-output-names = "xin32k", "rk808-clkout2";
+ interrupt-parent = <&gpio3>;
+ interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l_gpio>;
+ rockchip,system-power-controller;
+ wakeup-source;
+
+ vcc1-supply = <&vcc_sysin>;
+ vcc2-supply = <&vcc_sysin>;
+ vcc3-supply = <&vcc_sysin>;
+ vcc4-supply = <&vcc_sysin>;
+ vcc6-supply = <&vcc_sysin>;
+ vcc7-supply = <&vcc_sysin>;
+ vcc8-supply = <&vcc3v3_sys>;
+ vcc9-supply = <&vcc_sysin>;
+ vcc10-supply = <&vcc_sysin>;
+ vcc11-supply = <&vcc_sysin>;
+ vcc12-supply = <&vcc3v3_sys>;
+ vcc13-supply = <&vcc_sysin>;
+ vcc14-supply = <&vcc_sysin>;
+
+ regulators {
+ /* rk3399 center logic supply */
+ vdd_center: DCDC_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-name = "vdd_center";
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_cpu_l: DCDC_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-name = "vdd_cpu_l";
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc_ddr";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_1v8: vcc_wl: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc_1v8";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ /* not used */
+ LDO_REG1 {
+ };
+
+ /* not used */
+ LDO_REG2 {
+ };
+
+ vcc1v8_pmupll: LDO_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc1v8_pmupll";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc_sdio: LDO_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc_sdio";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3000000>;
+ };
+ };
+
+ vcca3v0_codec: LDO_REG5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcca3v0_codec";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v5: LDO_REG6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc_1v5";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1500000>;
+ };
+ };
+
+ vcca1v8_codec: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcca1v8_codec";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_3v0: LDO_REG8 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc_3v0";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3000000>;
+ };
+ };
+
+ vcc3v3_s3: SWITCH_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc3v3_s3";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_s0: SWITCH_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc3v3_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+
+ vdd_cpu_b: regulator@40 {
+ compatible = "silergy,syr827";
+ reg = <0x40>;
+ fcs,suspend-voltage-selector = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vsel1_gpio>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-compatible = "fan53555-reg";
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vdd_cpu_b";
+ regulator-ramp-delay = <1000>;
+ vin-supply = <&vcc_1v8>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_gpu: regulator@41 {
+ compatible = "silergy,syr828";
+ reg = <0x41>;
+ fcs,suspend-voltage-selector = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vsel2_gpio>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-compatible = "fan53555-reg";
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vdd_gpu";
+ regulator-ramp-delay = <1000>;
+ vin-supply = <&vcc_1v8>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ i2c-scl-falling-time-ns = <4>;
+ i2c-scl-rising-time-ns = <168>;
+ status = "okay";
+
+ es8316: es8316@11 {
+ compatible = "everest,es8316";
+ reg = <0x11>;
+ clocks = <&cru SCLK_I2S_8CH_OUT>;
+ clock-names = "mclk";
+ #sound-dai-cells = <0>;
+ };
+};
+
+&i2c3 {
+ i2c-scl-falling-time-ns = <15>;
+ i2c-scl-rising-time-ns = <450>;
+ status = "okay";
+};
+
+&i2c4 {
+ i2c-scl-falling-time-ns = <20>;
+ i2c-scl-rising-time-ns = <600>;
+ status = "okay";
+
+ fusb0: fusb30x@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+ fcs,int_n = <&gpio1 RK_PA2 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&fusb0_int_gpio>;
+ vbus-supply = <&vbus_typec>;
+
+ connector {
+ compatible = "usb-c-connector";
+ data-role = "host";
+ label = "USB-C";
+ op-sink-microwatt = <1000000>;
+ power-role = "dual";
+ sink-pdos =
+ <PDO_FIXED(5000, 2500, PDO_FIXED_USB_COMM)>;
+ source-pdos =
+ <PDO_FIXED(5000, 1400, PDO_FIXED_USB_COMM)>;
+ try-power-role = "sink";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ usbc_hs: endpoint {
+ remote-endpoint =
+ <&u2phy0_typec_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ usbc_ss: endpoint {
+ remote-endpoint =
+ <&tcphy0_typec_ss>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ usbc_dp: endpoint {
+ remote-endpoint =
+ <&tcphy0_typec_dp>;
+ };
+ };
+ };
+ };
+ };
+};
+
+&i2s1 {
+ #sound-dai-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s_8ch_mclk_gpio>, <&i2s1_2ch_bus>;
+ rockchip,capture-channels = <8>;
+ rockchip,playback-channels = <8>;
+ status = "okay";
+};
+
+&io_domains {
+ audio-supply = <&vcc_3v0>;
+ gpio1830-supply = <&vcc_3v0>;
+ sdmmc-supply = <&vcc_sdio>;
+ status = "okay";
+};
+
+&pcie_phy {
+ status = "okay";
+};
+
+&pcie0 {
+ bus-scan-delay-ms = <1000>;
+ ep-gpios = <&gpio2 RK_PD4 GPIO_ACTIVE_HIGH>;
+ max-link-speed = <2>;
+ num-lanes = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_clkreqn_cpm>;
+ vpcie0v9-supply = <&vcca0v9_s3>;
+ vpcie1v8-supply = <&vcca1v8_s3>;
+ vpcie3v3-supply = <&vcc3v3_ssd>;
+ status = "okay";
+};
+
+&pinctrl {
+ buttons {
+ pwrbtn_gpio: pwrbtn-gpio {
+ rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ lidbtn_gpio: lidbtn-gpio {
+ rockchip,pins = <1 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ dc-charger {
+ dc_det_gpio: dc-det-gpio {
+ rockchip,pins = <4 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ es8316 {
+ hp_det_gpio: hp-det-gpio {
+ rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+
+ fusb302x {
+ fusb0_int_gpio: fusb0-int-gpio {
+ rockchip,pins = <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ i2s1 {
+ i2s_8ch_mclk_gpio: i2s-8ch-mclk-gpio {
+ rockchip,pins = <4 RK_PA0 1 &pcfg_pull_none>;
+ };
+ };
+
+ lcd-panel {
+ lcdvcc_en_gpio: lcdvcc-en-gpio {
+ rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ panel_en_gpio: panel-en-gpio {
+ rockchip,pins = <1 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ lcd_panel_reset_gpio: lcd-panel-reset-gpio {
+ rockchip,pins = <4 RK_PD6 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ leds {
+ pwrled_gpio: pwrled_gpio {
+ rockchip,pins = <0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ slpled_gpio: slpled_gpio {
+ rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int_l_gpio: pmic-int-l-gpio {
+ rockchip,pins = <3 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ vsel1_gpio: vsel1-gpio {
+ rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+
+ vsel2_gpio: vsel2-gpio {
+ rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+
+ sdcard {
+ sdmmc0_pwr_h_gpio: sdmmc0-pwr-h-gpio {
+ rockchip,pins = <0 RK_PA1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ };
+
+ sdio-pwrseq {
+ wifi_enable_h_gpio: wifi-enable-h-gpio {
+ rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb-typec {
+ vcc5v0_typec0_en_gpio: vcc5v0-typec0-en-gpio {
+ rockchip,pins = <1 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ usb2 {
+ pwr_5v_gpio: pwr-5v-gpio {
+ rockchip,pins = <1 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ vcc5v0_host_en_gpio: vcc5v0-host-en-gpio {
+ rockchip,pins = <4 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ wireless-bluetooth {
+ bt_wake_gpio: bt-wake-gpio {
+ rockchip,pins = <2 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ bt_host_wake_gpio: bt-host-wake-gpio {
+ rockchip,pins = <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ bt_reset_gpio: bt-reset-gpio {
+ rockchip,pins = <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pmu_io_domains {
+ pmu1830-supply = <&vcc_3v0>;
+ status = "okay";
+};
+
+&pwm0 {
+ status = "okay";
+};
+
+&pwm2 {
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&vcca1v8_s3>;
+ status = "okay";
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_bus4>;
+ sd-uhs-sdr104;
+ status = "okay";
+};
+
+&sdio0 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdio0_bus4 &sdio0_cmd &sdio0_clk>;
+ sd-uhs-sdr104;
+ status = "okay";
+};
+
+&sdhci {
+ bus-width = <8>;
+ mmc-hs200-1_8v;
+ non-removable;
+ status = "okay";
+};
+
+&spi1 {
+ max-freq = <10000000>;
+ status = "okay";
+
+ spiflash: flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ m25p,fast-read;
+ spi-max-frequency = <10000000>;
+ };
+};
+
+&tcphy0 {
+ status = "okay";
+};
+
+&tcphy0_dp {
+ port {
+ tcphy0_typec_dp: endpoint {
+ remote-endpoint = <&usbc_dp>;
+ };
+ };
+};
+
+&tcphy0_usb3 {
+ port {
+ tcphy0_typec_ss: endpoint {
+ remote-endpoint = <&usbc_ss>;
+ };
+ };
+};
+
+&tcphy1 {
+ status = "okay";
+};
+
+&tsadc {
+ /* tshut mode 0:CRU 1:GPIO */
+ rockchip,hw-tshut-mode = <1>;
+ /* tshut polarity 0:LOW 1:HIGH */
+ rockchip,hw-tshut-polarity = <1>;
+ status = "okay";
+};
+
+&u2phy0 {
+ status = "okay";
+
+ u2phy0_otg: otg-port {
+ status = "okay";
+ };
+
+ u2phy0_host: host-port {
+ phy-supply = <&vcc5v0_otg>;
+ status = "okay";
+ };
+
+ port {
+ u2phy0_typec_hs: endpoint {
+ remote-endpoint = <&usbc_hs>;
+ };
+ };
+};
+
+&u2phy1 {
+ status = "okay";
+
+ u2phy1_otg: otg-port {
+ status = "okay";
+ };
+
+ u2phy1_host: host-port {
+ phy-supply = <&vcc5v0_otg>;
+ status = "okay";
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm4345c5";
+ clocks = <&rk808 1>;
+ clock-names = "lpo";
+ device-wakeup-gpios = <&gpio2 RK_PD3 GPIO_ACTIVE_HIGH>;
+ host-wakeup-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_HIGH>;
+ max-speed = <1500000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_host_wake_gpio &bt_wake_gpio &bt_reset_gpio>;
+ shutdown-gpios = <&gpio0 RK_PB1 GPIO_ACTIVE_HIGH>;
+ vbat-supply = <&wifi_bat>;
+ vddio-supply = <&vcc_wl>;
+ };
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&usb_host1_ehci {
+ status = "okay";
+};
+
+&usb_host1_ohci {
+ status = "okay";
+};
+
+&usbdrd3_0 {
+ status = "okay";
+};
+
+&usbdrd_dwc3_0 {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbdrd3_1 {
+ status = "okay";
+};
+
+&usbdrd_dwc3_1 {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&vopb {
+ status = "okay";
+};
+
+&vopb_mmu {
+ status = "okay";
+};
+
+&vopl {
+ status = "okay";
+};
+
+&vopl_mmu {
+ status = "okay";
+};
This commit adds initial dt support for the rk3399 based Pinebook Pro. Signed-off-by: Tobias Schramm <t.schramm@manjaro.org> --- arch/arm64/boot/dts/rockchip/Makefile | 1 + .../boot/dts/rockchip/rk3399-pinebook-pro.dts | 1096 +++++++++++++++++ 2 files changed, 1097 insertions(+) create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts