| Message ID | 20200314142327.25568-1-katsuhiro@katsuster.net (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | ARM: dts: rockchip: use DMA channels for UARTs of TinkerBoard | expand |
Hi, Am Samstag, 14. März 2020, 15:23:27 CET schrieb Katsuhiro Suzuki: > This patch enables to use DMAC for all UARTs that are connected to > dmac_peri core for TinkerBoard. > > Only uart2 is connected different DMAC (dmac_bus_s) so keep current > settings on this patch. This belongs in rk3288.dtsi, as this is definitly not board-specific, as the dma-uart connection is done inside the soc. At least on arm64 (rk3328, px30, probably more) we already have the uart dmas in the core dtsi without any problems. Is there any reason why you only did add it to the tinker board only? Heiko > Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net> > --- > arch/arm/boot/dts/rk3288-tinker.dtsi | 8 ++++++++ > 1 file changed, 8 insertions(+) > > diff --git a/arch/arm/boot/dts/rk3288-tinker.dtsi b/arch/arm/boot/dts/rk3288-tinker.dtsi > index 312582c1bd37..6efabeaf3c6d 100644 > --- a/arch/arm/boot/dts/rk3288-tinker.dtsi > +++ b/arch/arm/boot/dts/rk3288-tinker.dtsi > @@ -491,10 +491,14 @@ &tsadc { > }; > > &uart0 { > + dmas = <&dmac_peri 1>, <&dmac_peri 2>; > + dma-names = "tx", "rx"; > status = "okay"; > }; > > &uart1 { > + dmas = <&dmac_peri 3>, <&dmac_peri 4>; > + dma-names = "tx", "rx"; > status = "okay"; > }; > > @@ -503,10 +507,14 @@ &uart2 { > }; > > &uart3 { > + dmas = <&dmac_peri 7>, <&dmac_peri 8>; > + dma-names = "tx", "rx"; > status = "okay"; > }; > > &uart4 { > + dmas = <&dmac_peri 9>, <&dmac_peri 10>; > + dma-names = "tx", "rx"; > status = "okay"; > }; > >
Hello Heiko, > This belongs in rk3288.dtsi, as this is definitly not board-specific, as > the dma-uart connection is done inside the soc. > > At least on arm64 (rk3328, px30, probably more) we already have the > uart dmas in the core dtsi without any problems. > > Is there any reason why you only did add it to the tinker board only? There is no special reason. Simply I don't have and not tested on other boards of RK3288. But I hope these DMA settings can work correctly on other boards. I'll resend patch for rk3288.dtsi. Best Regards, Katsuhiro Suzuki On 2020/03/15 0:09, Heiko Stübner wrote: > Hi, > > Am Samstag, 14. März 2020, 15:23:27 CET schrieb Katsuhiro Suzuki: >> This patch enables to use DMAC for all UARTs that are connected to >> dmac_peri core for TinkerBoard. >> >> Only uart2 is connected different DMAC (dmac_bus_s) so keep current >> settings on this patch. > > This belongs in rk3288.dtsi, as this is definitly not board-specific, as > the dma-uart connection is done inside the soc. > > At least on arm64 (rk3328, px30, probably more) we already have the > uart dmas in the core dtsi without any problems. > > Is there any reason why you only did add it to the tinker board only? > > > Heiko > > >> Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net> >> --- >> arch/arm/boot/dts/rk3288-tinker.dtsi | 8 ++++++++ >> 1 file changed, 8 insertions(+) >> >> diff --git a/arch/arm/boot/dts/rk3288-tinker.dtsi b/arch/arm/boot/dts/rk3288-tinker.dtsi >> index 312582c1bd37..6efabeaf3c6d 100644 >> --- a/arch/arm/boot/dts/rk3288-tinker.dtsi >> +++ b/arch/arm/boot/dts/rk3288-tinker.dtsi >> @@ -491,10 +491,14 @@ &tsadc { >> }; >> >> &uart0 { >> + dmas = <&dmac_peri 1>, <&dmac_peri 2>; >> + dma-names = "tx", "rx"; >> status = "okay"; >> }; >> >> &uart1 { >> + dmas = <&dmac_peri 3>, <&dmac_peri 4>; >> + dma-names = "tx", "rx"; >> status = "okay"; >> }; >> >> @@ -503,10 +507,14 @@ &uart2 { >> }; >> >> &uart3 { >> + dmas = <&dmac_peri 7>, <&dmac_peri 8>; >> + dma-names = "tx", "rx"; >> status = "okay"; >> }; >> >> &uart4 { >> + dmas = <&dmac_peri 9>, <&dmac_peri 10>; >> + dma-names = "tx", "rx"; >> status = "okay"; >> }; >> >> > > > > >
diff --git a/arch/arm/boot/dts/rk3288-tinker.dtsi b/arch/arm/boot/dts/rk3288-tinker.dtsi index 312582c1bd37..6efabeaf3c6d 100644 --- a/arch/arm/boot/dts/rk3288-tinker.dtsi +++ b/arch/arm/boot/dts/rk3288-tinker.dtsi @@ -491,10 +491,14 @@ &tsadc { }; &uart0 { + dmas = <&dmac_peri 1>, <&dmac_peri 2>; + dma-names = "tx", "rx"; status = "okay"; }; &uart1 { + dmas = <&dmac_peri 3>, <&dmac_peri 4>; + dma-names = "tx", "rx"; status = "okay"; }; @@ -503,10 +507,14 @@ &uart2 { }; &uart3 { + dmas = <&dmac_peri 7>, <&dmac_peri 8>; + dma-names = "tx", "rx"; status = "okay"; }; &uart4 { + dmas = <&dmac_peri 9>, <&dmac_peri 10>; + dma-names = "tx", "rx"; status = "okay"; };
This patch enables to use DMAC for all UARTs that are connected to dmac_peri core for TinkerBoard. Only uart2 is connected different DMAC (dmac_bus_s) so keep current settings on this patch. Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net> --- arch/arm/boot/dts/rk3288-tinker.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+)