Message ID | 8a0cfe9e3018f7996c1563035bee76048941beb4.1583412540.git.amit.kucheria@linaro.org (mailing list archive) |
---|---|
State | Superseded |
Headers | show |
Series | Convert thermal bindings to yaml | expand |
On Thu, Mar 05, 2020 at 06:26:43PM +0530, Amit Kucheria wrote: > As part of moving the thermal bindings to YAML, split it up into 3 > bindings: thermal sensors, cooling devices and thermal zones. > > The thermal-zone binding is a software abstraction to capture the > properties of each zone - how often they should be checked, the > temperature thresholds (trips) at which mitigation actions need to be > taken and the level of mitigation needed at those thresholds. > > Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org> > --- > .../bindings/thermal/thermal-zones.yaml | 325 ++++++++++++++++++ > 1 file changed, 325 insertions(+) > create mode 100644 Documentation/devicetree/bindings/thermal/thermal-zones.yaml > > diff --git a/Documentation/devicetree/bindings/thermal/thermal-zones.yaml b/Documentation/devicetree/bindings/thermal/thermal-zones.yaml > new file mode 100644 > index 0000000000000..f8f3b72bc3119 > --- /dev/null > +++ b/Documentation/devicetree/bindings/thermal/thermal-zones.yaml > @@ -0,0 +1,325 @@ > +# SPDX-License-Identifier: (GPL-2.0) > +# Copyright 2020 Linaro Ltd. > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/thermal/thermal-zones.yaml# > +$schema: http://devicetree.org/meta-schemas/base.yaml# > + > +title: Thermal zone binding > + > +maintainers: > + - Amit Kucheria <amitk@kernel.org> > + > +description: | > + Thermal management is achieved in devicetree by describing the sensor hardware > + and the software abstraction of cooling devices and thermal zones required to > + take appropriate action to mitigate thermal overloads. > + > + The following node types are used to completely describe a thermal management > + system in devicetree: > + - thermal-sensor: device that measures temperature, has SoC-specific bindings > + - cooling-device: device used to dissipate heat either passively or actively > + - thermal-zones: a container of the following node types used to describe all > + thermal data for the platform > + > + This binding describes the thermal-zones. > + > + The polling-delay properties of a thermal-zone are bound to the maximum dT/dt > + (temperature derivative over time) in two situations for a thermal zone: > + 1. when passive cooling is activated (polling-delay-passive) > + 2. when the zone just needs to be monitored (polling-delay) or when > + active cooling is activated. > + > + The maximum dT/dt is highly bound to hardware power consumption and > + dissipation capability. The delays should be chosen to account for said > + max dT/dt, such that a device does not cross several trip boundaries > + unexpectedly between polls. Choosing the right polling delays shall avoid > + having the device in temperature ranges that may damage the silicon structures > + and reduce silicon lifetime. > + > +properties: > + thermal-zones: > + type: object > + description: > + A /thermal-zones node is required in order to use the thermal framework to > + manage input from the various thermal zones in the system in order to > + mitigate thermal overload conditions. It does not represent a real device > + in the system, but acts as a container to link thermal sensor devices, > + platform-data regarding temperature thresholds and the mitigation actions > + to take when the temperature crosses those thresholds. > + > + properties: > + $nodename: > + pattern: "^[a-zA-Z][a-zA-Z0-9,\\-]{1,12}-thermal$" These 3 lines should be: patternProperties: "^[a-zA-Z][a-zA-Z0-9,\\-]{1,12}-thermal$": Though we should drop ',' as well. $nodename is only needed at the top level where it's kind of special. > + type: object > + description: > + Each thermal zone node contains information about how frequently it > + must be checked, the sensor responsible for reporting temperature for > + this zone, one sub-node containing the various trip points for this > + zone and one sub-node containing all the zone cooling-maps. > + > + properties: > + polling-delay: > + $ref: /schemas/types.yaml#/definitions/uint32 > + minimum: 0 The type is unsigned, so the min is already 0. > + description: > + The maximum number of milliseconds to wait between polls when > + checking this thermal zone. Setting this to 0 disables the polling > + timers setup by the thermal framework and assumes that the thermal > + sensors in this zone support interrupts. > + > + polling-delay-passive: > + $ref: /schemas/types.yaml#/definitions/uint32 > + minimum: 0 > + description: > + The maximum number of milliseconds to wait between polls when > + checking this thermal zone while doing passive cooling. Setting > + this to 0 disables the polling timers setup by the thermal > + framework and assumes that the thermal sensors in this zone > + support interrupts. > + > + thermal-sensors: > + $ref: /schemas/types.yaml#/definitions/phandle-array > + description: > + A list of thermal sensor phandles and sensor specifiers used to > + monitor this thermal zone. > + > + trips: > + type: object > + description: > + This node describes a set of points in the temperature domain at > + which the thermal framework needs to takes action. The actions to > + be taken are defined in another node called cooling-maps. > + > + patternProperties: > + "^[a-zA-Z][a-zA-Z0-9,+\\._]{0,63}$": Drop ',', '+', '.', and ideally '_'. Probably need to add '-'. > + type: object > + > + properties: > + temperature: > + $ref: /schemas/types.yaml#/definitions/int32 > + minimum: -273000 > + maximum: 200000 > + description: > + An integer expressing the trip temperature in millicelsius. > + > + hysteresis: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: > + An unsigned integer expressing the hysteresis delta with > + respect to the trip temperature property above, also in > + millicelsius. > + > + type: Needs a type reference (string). > + enum: > + # active: enable active cooling e.g. fans > + - active Wrong indentation. Should be 2 less. Also, I think this would be more readable: - active # enable active cooling e.g. fans > + # passive: enable passive cooling e.g. throttling cpu > + - passive > + # hot: send notification to driver if .notify > + # callback registered > + - hot > + # critical: send notification to driver if .notify > + # callback registered and trigger a shutdown > + - critical > + description: | > + There are four valid trip types: active, passive, hot, > + critical. > + > + The critical trip type is used to set the maximum > + temperature threshold above which the HW becomes > + unstable and underlying firmware might even trigger a > + reboot. Hitting the critical threshold triggers a system > + shutdown. > + > + The hot trip type can be used to send a notification to > + the thermal driver (if a .notify callback is registered). > + The action to be taken is left to the driver. > + > + The passive trip type can be used to slow down HW e.g. run > + the CPU, GPU, bus at a lower frequency. > + > + The active trip type can be used to control other HW to > + help in cooling e.g. fans can be sped up or slowed down > + > + required: > + - temperature > + - hysteresis > + - type > + > + additionalProperties: false You need 'additionalProperties' on the child nodes too, or are there vendor specific properties allowed? > + > + cooling-maps: > + type: object > + description: > + This node describes the action to be taken when a thermal zone > + crosses one of the temperature thresholds described in the trips > + node. The action takes the form of a mapping relation between a > + trip and the target cooling device state. > + > + patternProperties: > + "^map[0-9][-a-zA-Z0-9]*$": > + type: object > + > + properties: > + trip: > + $ref: /schemas/types.yaml#/definitions/phandle > + description: > + A phandle of a trip point node within this thermal zone. > + > + cooling-device: > + $ref: /schemas/types.yaml#/definitions/phandle-array > + description: > + A list of cooling device phandles along with the minimum > + and maximum cooling state specifiers for each cooling > + device. Using the THERMAL_NO_LIMIT (-1UL) constant in the > + cooling-device phandle limit specifier lets the framework > + use the minimum and maximum cooling state for that cooling > + device automatically. > + > + contribution: > + $ref: /schemas/types.yaml#/definitions/uint32 > + minimum: 0 > + maximum: 100 > + description: > + The contribution of the cooling devices at the trip > + temperature, both referenced in this map, to this thermal > + zone as a percentage. > + > + required: > + - trip > + - cooling-device > + 'additionalProperties' for map* nodes? > + additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + #include <dt-bindings/thermal/thermal.h> > + > + // Example 1: SDM845 TSENS > + soc: soc@0 { > + #address-cells = <2>; > + #size-cells = <2>; > + > + /* ... */ > + > + tsens0: thermal-sensor@c263000 { > + compatible = "qcom,sdm845-tsens", "qcom,tsens-v2"; > + reg = <0 0x0c263000 0 0x1ff>, /* TM */ > + <0 0x0c222000 0 0x1ff>; /* SROT */ > + #qcom,sensors = <13>; > + interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "uplow", "critical"; > + #thermal-sensor-cells = <1>; > + }; > + > + tsens1: thermal-sensor@c265000 { > + compatible = "qcom,sdm845-tsens", "qcom,tsens-v2"; > + reg = <0 0x0c265000 0 0x1ff>, /* TM */ > + <0 0x0c223000 0 0x1ff>; /* SROT */ > + #qcom,sensors = <8>; > + interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 509 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "uplow", "critical"; > + #thermal-sensor-cells = <1>; > + }; > + }; > + > + /* ... */ > + > + thermal-zones { > + cpu0-thermal { > + polling-delay-passive = <250>; > + polling-delay = <1000>; > + > + thermal-sensors = <&tsens0 1>; > + > + trips { > + cpu0_alert0: trip-point0 { > + temperature = <90000>; > + hysteresis = <2000>; > + type = "passive"; > + }; > + > + cpu0_alert1: trip-point1 { > + temperature = <95000>; > + hysteresis = <2000>; > + type = "passive"; > + }; > + > + cpu0_crit: cpu_crit { > + temperature = <110000>; > + hysteresis = <1000>; > + type = "critical"; > + }; > + }; > + > + cooling-maps { > + map0 { > + trip = <&cpu0_alert0>; > + cooling-device = <&CPU0 THERMAL_NO_LIMIT > + THERMAL_NO_LIMIT>, > + <&CPU1 THERMAL_NO_LIMIT > + THERMAL_NO_LIMIT>, > + <&CPU2 THERMAL_NO_LIMIT > + THERMAL_NO_LIMIT>, > + <&CPU3 THERMAL_NO_LIMIT > + THERMAL_NO_LIMIT>; > + }; > + > + map1 { > + trip = <&cpu0_alert1>; > + cooling-device = <&CPU0 THERMAL_NO_LIMIT > + THERMAL_NO_LIMIT>, > + <&CPU1 THERMAL_NO_LIMIT > + THERMAL_NO_LIMIT>, > + <&CPU2 THERMAL_NO_LIMIT > + THERMAL_NO_LIMIT>, > + <&CPU3 THERMAL_NO_LIMIT > + THERMAL_NO_LIMIT>; > + }; > + }; > + }; > + > + /* ... */ > + > + cluster0-thermal { > + polling-delay-passive = <250>; > + polling-delay = <1000>; > + > + thermal-sensors = <&tsens0 5>; > + > + trips { > + cluster0_alert0: trip-point0 { > + temperature = <90000>; > + hysteresis = <2000>; > + type = "hot"; > + }; > + cluster0_crit: cluster0_crit { > + temperature = <110000>; > + hysteresis = <2000>; > + type = "critical"; > + }; > + }; > + }; > + > + /* ... */ > + > + gpu-thermal-top { This one is not going to match (which should cause an error). > + polling-delay-passive = <250>; > + polling-delay = <1000>; > + > + thermal-sensors = <&tsens0 11>; > + > + trips { > + gpu1_alert0: trip-point0 { > + temperature = <90000>; > + hysteresis = <2000>; > + type = "hot"; > + }; > + }; > + }; > + }; > +... > -- > 2.20.1 >
Hi Rob, Thanks for the review. On Wed, Mar 11, 2020 at 8:19 PM Rob Herring <robh@kernel.org> wrote: > > On Thu, Mar 05, 2020 at 06:26:43PM +0530, Amit Kucheria wrote: > > As part of moving the thermal bindings to YAML, split it up into 3 > > bindings: thermal sensors, cooling devices and thermal zones. > > > > The thermal-zone binding is a software abstraction to capture the > > properties of each zone - how often they should be checked, the > > temperature thresholds (trips) at which mitigation actions need to be > > taken and the level of mitigation needed at those thresholds. > > > > Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org> > > --- > > .../bindings/thermal/thermal-zones.yaml | 325 ++++++++++++++++++ > > 1 file changed, 325 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/thermal/thermal-zones.yaml > > > > diff --git a/Documentation/devicetree/bindings/thermal/thermal-zones.yaml b/Documentation/devicetree/bindings/thermal/thermal-zones.yaml > > new file mode 100644 > > index 0000000000000..f8f3b72bc3119 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/thermal/thermal-zones.yaml > > @@ -0,0 +1,325 @@ > > +# SPDX-License-Identifier: (GPL-2.0) > > +# Copyright 2020 Linaro Ltd. > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/thermal/thermal-zones.yaml# > > +$schema: http://devicetree.org/meta-schemas/base.yaml# > > + > > +title: Thermal zone binding > > + > > +maintainers: > > + - Amit Kucheria <amitk@kernel.org> > > + > > +description: | > > + Thermal management is achieved in devicetree by describing the sensor hardware > > + and the software abstraction of cooling devices and thermal zones required to > > + take appropriate action to mitigate thermal overloads. > > + > > + The following node types are used to completely describe a thermal management > > + system in devicetree: > > + - thermal-sensor: device that measures temperature, has SoC-specific bindings > > + - cooling-device: device used to dissipate heat either passively or actively > > + - thermal-zones: a container of the following node types used to describe all > > + thermal data for the platform > > + > > + This binding describes the thermal-zones. > > + > > + The polling-delay properties of a thermal-zone are bound to the maximum dT/dt > > + (temperature derivative over time) in two situations for a thermal zone: > > + 1. when passive cooling is activated (polling-delay-passive) > > + 2. when the zone just needs to be monitored (polling-delay) or when > > + active cooling is activated. > > + > > + The maximum dT/dt is highly bound to hardware power consumption and > > + dissipation capability. The delays should be chosen to account for said > > + max dT/dt, such that a device does not cross several trip boundaries > > + unexpectedly between polls. Choosing the right polling delays shall avoid > > + having the device in temperature ranges that may damage the silicon structures > > + and reduce silicon lifetime. > > + > > +properties: > > + thermal-zones: > > + type: object > > + description: > > + A /thermal-zones node is required in order to use the thermal framework to > > + manage input from the various thermal zones in the system in order to > > + mitigate thermal overload conditions. It does not represent a real device > > + in the system, but acts as a container to link thermal sensor devices, > > + platform-data regarding temperature thresholds and the mitigation actions > > + to take when the temperature crosses those thresholds. > > + > > > + properties: > > + $nodename: > > + pattern: "^[a-zA-Z][a-zA-Z0-9,\\-]{1,12}-thermal$" > > These 3 lines should be: > > patternProperties: > "^[a-zA-Z][a-zA-Z0-9,\\-]{1,12}-thermal$": > > Though we should drop ',' as well. > > $nodename is only needed at the top level where it's kind of special. Fixed. > > + type: object > > + description: > > + Each thermal zone node contains information about how frequently it > > + must be checked, the sensor responsible for reporting temperature for > > + this zone, one sub-node containing the various trip points for this > > + zone and one sub-node containing all the zone cooling-maps. > > + > > + properties: > > + polling-delay: > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + minimum: 0 > > The type is unsigned, so the min is already 0. Dropped. > > + description: > > + The maximum number of milliseconds to wait between polls when > > + checking this thermal zone. Setting this to 0 disables the polling > > + timers setup by the thermal framework and assumes that the thermal > > + sensors in this zone support interrupts. > > + > > + polling-delay-passive: > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + minimum: 0 Dropped. > > + description: > > + The maximum number of milliseconds to wait between polls when > > + checking this thermal zone while doing passive cooling. Setting > > + this to 0 disables the polling timers setup by the thermal > > + framework and assumes that the thermal sensors in this zone > > + support interrupts. > > + > > + thermal-sensors: > > + $ref: /schemas/types.yaml#/definitions/phandle-array > > + description: > > + A list of thermal sensor phandles and sensor specifiers used to > > + monitor this thermal zone. > > + > > + trips: > > + type: object > > + description: > > + This node describes a set of points in the temperature domain at > > + which the thermal framework needs to takes action. The actions to > > + be taken are defined in another node called cooling-maps. > > + > > + patternProperties: > > + "^[a-zA-Z][a-zA-Z0-9,+\\._]{0,63}$": > > Drop ',', '+', '.', and ideally '_'. Probably need to add '-'. Dropping underscore flags a lot of DTs in dtbs_check. Do you want me to go fix them or can we live with the underscore. Is there some document I should read on why underscore isn't desirable? Fixed the rest. > > > + type: object > > + > > + properties: > > + temperature: > > + $ref: /schemas/types.yaml#/definitions/int32 > > + minimum: -273000 > > + maximum: 200000 > > + description: > > + An integer expressing the trip temperature in millicelsius. > > + > > + hysteresis: > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + description: > > + An unsigned integer expressing the hysteresis delta with > > + respect to the trip temperature property above, also in > > + millicelsius. > > + > > + type: > > Needs a type reference (string). Fixed. > > > + enum: > > + # active: enable active cooling e.g. fans > > + - active > > Wrong indentation. Should be 2 less. > > Also, I think this would be more readable: > > - active # enable active cooling e.g. fans Yes, fixed. > > > + # passive: enable passive cooling e.g. throttling cpu > > + - passive > > + # hot: send notification to driver if .notify > > + # callback registered > > + - hot > > + # critical: send notification to driver if .notify > > + # callback registered and trigger a shutdown > > + - critical > > + description: | > > + There are four valid trip types: active, passive, hot, > > + critical. > > + > > + The critical trip type is used to set the maximum > > + temperature threshold above which the HW becomes > > + unstable and underlying firmware might even trigger a > > + reboot. Hitting the critical threshold triggers a system > > + shutdown. > > + > > + The hot trip type can be used to send a notification to > > + the thermal driver (if a .notify callback is registered). > > + The action to be taken is left to the driver. > > + > > + The passive trip type can be used to slow down HW e.g. run > > + the CPU, GPU, bus at a lower frequency. > > + > > + The active trip type can be used to control other HW to > > + help in cooling e.g. fans can be sped up or slowed down > > + > > + required: > > + - temperature > > + - hysteresis > > + - type > > + > > + additionalProperties: false > > You need 'additionalProperties' on the child nodes too, or are there > vendor specific properties allowed? Done. No vendor-specific properties allowed here. > > + > > + cooling-maps: > > + type: object > > + description: > > + This node describes the action to be taken when a thermal zone > > + crosses one of the temperature thresholds described in the trips > > + node. The action takes the form of a mapping relation between a > > + trip and the target cooling device state. > > + > > + patternProperties: > > + "^map[0-9][-a-zA-Z0-9]*$": > > + type: object > > + > > + properties: > > + trip: > > + $ref: /schemas/types.yaml#/definitions/phandle > > + description: > > + A phandle of a trip point node within this thermal zone. > > + > > + cooling-device: > > + $ref: /schemas/types.yaml#/definitions/phandle-array > > + description: > > + A list of cooling device phandles along with the minimum > > + and maximum cooling state specifiers for each cooling > > + device. Using the THERMAL_NO_LIMIT (-1UL) constant in the > > + cooling-device phandle limit specifier lets the framework > > + use the minimum and maximum cooling state for that cooling > > + device automatically. > > + > > + contribution: > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + minimum: 0 > > + maximum: 100 > > + description: > > + The contribution of the cooling devices at the trip > > + temperature, both referenced in this map, to this thermal > > + zone as a percentage. > > + > > + required: > > + - trip > > + - cooling-device > > + > > 'additionalProperties' for map* nodes? Done. > > + additionalProperties: false > > + > > +examples: > > + - | > > + #include <dt-bindings/interrupt-controller/arm-gic.h> > > + #include <dt-bindings/thermal/thermal.h> > > + > > + // Example 1: SDM845 TSENS > > + soc: soc@0 { > > + #address-cells = <2>; > > + #size-cells = <2>; > > + > > + /* ... */ > > + > > + tsens0: thermal-sensor@c263000 { > > + compatible = "qcom,sdm845-tsens", "qcom,tsens-v2"; > > + reg = <0 0x0c263000 0 0x1ff>, /* TM */ > > + <0 0x0c222000 0 0x1ff>; /* SROT */ > > + #qcom,sensors = <13>; > > + interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>; > > + interrupt-names = "uplow", "critical"; > > + #thermal-sensor-cells = <1>; > > + }; > > + > > + tsens1: thermal-sensor@c265000 { > > + compatible = "qcom,sdm845-tsens", "qcom,tsens-v2"; > > + reg = <0 0x0c265000 0 0x1ff>, /* TM */ > > + <0 0x0c223000 0 0x1ff>; /* SROT */ > > + #qcom,sensors = <8>; > > + interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 509 IRQ_TYPE_LEVEL_HIGH>; > > + interrupt-names = "uplow", "critical"; > > + #thermal-sensor-cells = <1>; > > + }; > > + }; > > + > > + /* ... */ > > + > > + thermal-zones { > > + cpu0-thermal { > > + polling-delay-passive = <250>; > > + polling-delay = <1000>; > > + > > + thermal-sensors = <&tsens0 1>; > > + > > + trips { > > + cpu0_alert0: trip-point0 { > > + temperature = <90000>; > > + hysteresis = <2000>; > > + type = "passive"; > > + }; > > + > > + cpu0_alert1: trip-point1 { > > + temperature = <95000>; > > + hysteresis = <2000>; > > + type = "passive"; > > + }; > > + > > + cpu0_crit: cpu_crit { > > + temperature = <110000>; > > + hysteresis = <1000>; > > + type = "critical"; > > + }; > > + }; > > + > > + cooling-maps { > > + map0 { > > + trip = <&cpu0_alert0>; > > + cooling-device = <&CPU0 THERMAL_NO_LIMIT > > + THERMAL_NO_LIMIT>, > > + <&CPU1 THERMAL_NO_LIMIT > > + THERMAL_NO_LIMIT>, > > + <&CPU2 THERMAL_NO_LIMIT > > + THERMAL_NO_LIMIT>, > > + <&CPU3 THERMAL_NO_LIMIT > > + THERMAL_NO_LIMIT>; > > + }; > > + > > + map1 { > > + trip = <&cpu0_alert1>; > > + cooling-device = <&CPU0 THERMAL_NO_LIMIT > > + THERMAL_NO_LIMIT>, > > + <&CPU1 THERMAL_NO_LIMIT > > + THERMAL_NO_LIMIT>, > > + <&CPU2 THERMAL_NO_LIMIT > > + THERMAL_NO_LIMIT>, > > + <&CPU3 THERMAL_NO_LIMIT > > + THERMAL_NO_LIMIT>; > > + }; > > + }; > > + }; > > + > > + /* ... */ > > + > > + cluster0-thermal { > > + polling-delay-passive = <250>; > > + polling-delay = <1000>; > > + > > + thermal-sensors = <&tsens0 5>; > > + > > + trips { > > + cluster0_alert0: trip-point0 { > > + temperature = <90000>; > > + hysteresis = <2000>; > > + type = "hot"; > > + }; > > + cluster0_crit: cluster0_crit { > > + temperature = <110000>; > > + hysteresis = <2000>; > > + type = "critical"; > > + }; > > + }; > > + }; > > + > > + /* ... */ > > + > > + gpu-thermal-top { > > This one is not going to match (which should cause an error). Good catch. Unfortunately, this isn't getting caught. Nor is the 12-char limitation before -thermal in the thermal zone name. I can't figure out why. > > + polling-delay-passive = <250>; > > + polling-delay = <1000>; > > + > > + thermal-sensors = <&tsens0 11>; > > + > > + trips { > > + gpu1_alert0: trip-point0 { > > + temperature = <90000>; > > + hysteresis = <2000>; > > + type = "hot"; > > + }; > > + }; > > + }; > > + }; > > +... > > -- > > 2.20.1 > >
On Mon, Mar 23, 2020 at 2:46 PM Amit Kucheria <amit.kucheria@linaro.org> wrote: > > Hi Rob, > > Thanks for the review. > > On Wed, Mar 11, 2020 at 8:19 PM Rob Herring <robh@kernel.org> wrote: > > > > On Thu, Mar 05, 2020 at 06:26:43PM +0530, Amit Kucheria wrote: > > > As part of moving the thermal bindings to YAML, split it up into 3 > > > bindings: thermal sensors, cooling devices and thermal zones. > > > > > > The thermal-zone binding is a software abstraction to capture the > > > properties of each zone - how often they should be checked, the > > > temperature thresholds (trips) at which mitigation actions need to be > > > taken and the level of mitigation needed at those thresholds. [...] > > > + trips: > > > + type: object > > > + description: > > > + This node describes a set of points in the temperature domain at > > > + which the thermal framework needs to takes action. The actions to > > > + be taken are defined in another node called cooling-maps. > > > + > > > + patternProperties: > > > + "^[a-zA-Z][a-zA-Z0-9,+\\._]{0,63}$": > > > > Drop ',', '+', '.', and ideally '_'. Probably need to add '-'. > > Dropping underscore flags a lot of DTs in dtbs_check. Do you want me > to go fix them or can we live with the underscore. Is there some > document I should read on why underscore isn't desirable? Just convention. dtc will warn (with W=2), but we probably should document that better. Anyways, fine to leave '_' here. > > > + /* ... */ > > > + > > > + gpu-thermal-top { > > > > This one is not going to match (which should cause an error). > > Good catch. Unfortunately, this isn't getting caught. Nor is the > 12-char limitation before -thermal in the thermal zone name. I can't > figure out why. That's because this schema has to be included by another schema which matches on a parent node containing 'thermal-zones'. If 'thermal-zones' can be at the root node, then you should rework this such that you have $nodename: {const: thermal-zones} as a top-level property. Rob
On Tue, Mar 24, 2020 at 2:46 AM Rob Herring <robh@kernel.org> wrote: > > On Mon, Mar 23, 2020 at 2:46 PM Amit Kucheria <amit.kucheria@linaro.org> wrote: > > > > Hi Rob, > > > > Thanks for the review. > > > > On Wed, Mar 11, 2020 at 8:19 PM Rob Herring <robh@kernel.org> wrote: > > > > > > On Thu, Mar 05, 2020 at 06:26:43PM +0530, Amit Kucheria wrote: > > > > As part of moving the thermal bindings to YAML, split it up into 3 > > > > bindings: thermal sensors, cooling devices and thermal zones. > > > > > > > > The thermal-zone binding is a software abstraction to capture the > > > > properties of each zone - how often they should be checked, the > > > > temperature thresholds (trips) at which mitigation actions need to be > > > > taken and the level of mitigation needed at those thresholds. > [...] > > > > > + /* ... */ > > > > + > > > > + gpu-thermal-top { > > > > > > This one is not going to match (which should cause an error). > > > > Good catch. Unfortunately, this isn't getting caught. Nor is the > > 12-char limitation before -thermal in the thermal zone name. I can't > > figure out why. > > That's because this schema has to be included by another schema which > matches on a parent node containing 'thermal-zones'. If > 'thermal-zones' can be at the root node, then you should rework this > such that you have $nodename: {const: thermal-zones} as a top-level > property. I've done all the change requested in the review(see attached patch), including moving to properties: $nodename: const: thermal-zones but that generates a bunch of errors similar to: /home/amit/work/builds/build-aarch64/Documentation/devicetree/bindings/arm/zte.example.dt.yaml: /: $nodename:0: 'thermal-zones' was expected /home/amit/work/builds/build-aarch64/Documentation/devicetree/bindings/arm/psci.example.dt.yaml: /: $nodename:0: 'thermal-zones' was expected /home/amit/work/builds/build-aarch64/Documentation/devicetree/bindings/arm/sunxi.example.dt.yaml: /: $nodename:0: 'thermal-zones' was expected /home/amit/work/builds/build-aarch64/Documentation/devicetree/bindings/arm/sprd/sprd.example.dt.yaml: /: $nodename:0: 'thermal-zones' was expected /home/amit/work/builds/build-aarch64/Documentation/devicetree/bindings/arm/calxeda.example.dt.yaml: /: $nodename:0: 'thermal-zones' was expected /home/amit/work/builds/build-aarch64/Documentation/devicetree/bindings/arm/ti/ti,davinci.example.dt.yaml: /: $nodename:0: 'thermal-zones' was expected /home/amit/work/builds/build-aarch64/Documentation/devicetree/bindings/arm/spear.example.dt.yaml: /: $nodename:0: 'thermal-zones' was expected /home/amit/work/builds/build-aarch64/Documentation/devicetree/bindings/arm/ti/nspire.example.dt.yaml: /: $nodename:0: 'thermal-zones' was expected It seems like dtc is expecting every node to have a thermal-zones node? Looking at other root nodes such as cpus.yaml, the main difference I noticed was the absence of the "select: true" property. However, if I remove that, we go back to the schema not being applied. You mentioned that the thermal-zones schema needs to included by another schema. What did you mean by that? Regards, Amit
On Tue, Mar 24, 2020 at 4:33 AM Amit Kucheria <amit.kucheria@linaro.org> wrote: > > On Tue, Mar 24, 2020 at 2:46 AM Rob Herring <robh@kernel.org> wrote: > > > > On Mon, Mar 23, 2020 at 2:46 PM Amit Kucheria <amit.kucheria@linaro.org> wrote: > > > > > > Hi Rob, > > > > > > Thanks for the review. > > > > > > On Wed, Mar 11, 2020 at 8:19 PM Rob Herring <robh@kernel.org> wrote: > > > > > > > > On Thu, Mar 05, 2020 at 06:26:43PM +0530, Amit Kucheria wrote: > > > > > As part of moving the thermal bindings to YAML, split it up into 3 > > > > > bindings: thermal sensors, cooling devices and thermal zones. > > > > > > > > > > The thermal-zone binding is a software abstraction to capture the > > > > > properties of each zone - how often they should be checked, the > > > > > temperature thresholds (trips) at which mitigation actions need to be > > > > > taken and the level of mitigation needed at those thresholds. > > > > [...] > > > > > > > > + /* ... */ > > > > > + > > > > > + gpu-thermal-top { > > > > > > > > This one is not going to match (which should cause an error). > > > > > > Good catch. Unfortunately, this isn't getting caught. Nor is the > > > 12-char limitation before -thermal in the thermal zone name. I can't > > > figure out why. > > > > That's because this schema has to be included by another schema which > > matches on a parent node containing 'thermal-zones'. If > > 'thermal-zones' can be at the root node, then you should rework this > > such that you have $nodename: {const: thermal-zones} as a top-level > > property. > > I've done all the change requested in the review(see attached patch), > including moving to > > properties: > $nodename: > const: thermal-zones > > but that generates a bunch of errors similar to: > > /home/amit/work/builds/build-aarch64/Documentation/devicetree/bindings/arm/zte.example.dt.yaml: > /: $nodename:0: 'thermal-zones' was expected > /home/amit/work/builds/build-aarch64/Documentation/devicetree/bindings/arm/psci.example.dt.yaml: > /: $nodename:0: 'thermal-zones' was expected > /home/amit/work/builds/build-aarch64/Documentation/devicetree/bindings/arm/sunxi.example.dt.yaml: > /: $nodename:0: 'thermal-zones' was expected > /home/amit/work/builds/build-aarch64/Documentation/devicetree/bindings/arm/sprd/sprd.example.dt.yaml: > /: $nodename:0: 'thermal-zones' was expected > /home/amit/work/builds/build-aarch64/Documentation/devicetree/bindings/arm/calxeda.example.dt.yaml: > /: $nodename:0: 'thermal-zones' was expected > /home/amit/work/builds/build-aarch64/Documentation/devicetree/bindings/arm/ti/ti,davinci.example.dt.yaml: > /: $nodename:0: 'thermal-zones' was expected > /home/amit/work/builds/build-aarch64/Documentation/devicetree/bindings/arm/spear.example.dt.yaml: > /: $nodename:0: 'thermal-zones' was expected > /home/amit/work/builds/build-aarch64/Documentation/devicetree/bindings/arm/ti/nspire.example.dt.yaml: > /: $nodename:0: 'thermal-zones' was expected > > It seems like dtc is expecting every node to have a thermal-zones node? > > Looking at other root nodes such as cpus.yaml, the main difference I > noticed was the absence of the "select: true" property. However, if I > remove that, we go back to the schema not being applied. 'select: true' should be dropped. It will be applied to any 'thermal-zones' nodes. The generated 'select' will use $nodename if compatible is not present for the schema. I tested that putting an error in the example works. > You mentioned that the thermal-zones schema needs to included by > another schema. What did you mean by that? Nevermind, I wasn't thinking that it's a top-level node. If it was a child node, then you'd want to include it from the parent schemas. Rob
diff --git a/Documentation/devicetree/bindings/thermal/thermal-zones.yaml b/Documentation/devicetree/bindings/thermal/thermal-zones.yaml new file mode 100644 index 0000000000000..f8f3b72bc3119 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/thermal-zones.yaml @@ -0,0 +1,325 @@ +# SPDX-License-Identifier: (GPL-2.0) +# Copyright 2020 Linaro Ltd. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/thermal/thermal-zones.yaml# +$schema: http://devicetree.org/meta-schemas/base.yaml# + +title: Thermal zone binding + +maintainers: + - Amit Kucheria <amitk@kernel.org> + +description: | + Thermal management is achieved in devicetree by describing the sensor hardware + and the software abstraction of cooling devices and thermal zones required to + take appropriate action to mitigate thermal overloads. + + The following node types are used to completely describe a thermal management + system in devicetree: + - thermal-sensor: device that measures temperature, has SoC-specific bindings + - cooling-device: device used to dissipate heat either passively or actively + - thermal-zones: a container of the following node types used to describe all + thermal data for the platform + + This binding describes the thermal-zones. + + The polling-delay properties of a thermal-zone are bound to the maximum dT/dt + (temperature derivative over time) in two situations for a thermal zone: + 1. when passive cooling is activated (polling-delay-passive) + 2. when the zone just needs to be monitored (polling-delay) or when + active cooling is activated. + + The maximum dT/dt is highly bound to hardware power consumption and + dissipation capability. The delays should be chosen to account for said + max dT/dt, such that a device does not cross several trip boundaries + unexpectedly between polls. Choosing the right polling delays shall avoid + having the device in temperature ranges that may damage the silicon structures + and reduce silicon lifetime. + +properties: + thermal-zones: + type: object + description: + A /thermal-zones node is required in order to use the thermal framework to + manage input from the various thermal zones in the system in order to + mitigate thermal overload conditions. It does not represent a real device + in the system, but acts as a container to link thermal sensor devices, + platform-data regarding temperature thresholds and the mitigation actions + to take when the temperature crosses those thresholds. + + properties: + $nodename: + pattern: "^[a-zA-Z][a-zA-Z0-9,\\-]{1,12}-thermal$" + type: object + description: + Each thermal zone node contains information about how frequently it + must be checked, the sensor responsible for reporting temperature for + this zone, one sub-node containing the various trip points for this + zone and one sub-node containing all the zone cooling-maps. + + properties: + polling-delay: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + description: + The maximum number of milliseconds to wait between polls when + checking this thermal zone. Setting this to 0 disables the polling + timers setup by the thermal framework and assumes that the thermal + sensors in this zone support interrupts. + + polling-delay-passive: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + description: + The maximum number of milliseconds to wait between polls when + checking this thermal zone while doing passive cooling. Setting + this to 0 disables the polling timers setup by the thermal + framework and assumes that the thermal sensors in this zone + support interrupts. + + thermal-sensors: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: + A list of thermal sensor phandles and sensor specifiers used to + monitor this thermal zone. + + trips: + type: object + description: + This node describes a set of points in the temperature domain at + which the thermal framework needs to takes action. The actions to + be taken are defined in another node called cooling-maps. + + patternProperties: + "^[a-zA-Z][a-zA-Z0-9,+\\._]{0,63}$": + type: object + + properties: + temperature: + $ref: /schemas/types.yaml#/definitions/int32 + minimum: -273000 + maximum: 200000 + description: + An integer expressing the trip temperature in millicelsius. + + hysteresis: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + An unsigned integer expressing the hysteresis delta with + respect to the trip temperature property above, also in + millicelsius. + + type: + enum: + # active: enable active cooling e.g. fans + - active + # passive: enable passive cooling e.g. throttling cpu + - passive + # hot: send notification to driver if .notify + # callback registered + - hot + # critical: send notification to driver if .notify + # callback registered and trigger a shutdown + - critical + description: | + There are four valid trip types: active, passive, hot, + critical. + + The critical trip type is used to set the maximum + temperature threshold above which the HW becomes + unstable and underlying firmware might even trigger a + reboot. Hitting the critical threshold triggers a system + shutdown. + + The hot trip type can be used to send a notification to + the thermal driver (if a .notify callback is registered). + The action to be taken is left to the driver. + + The passive trip type can be used to slow down HW e.g. run + the CPU, GPU, bus at a lower frequency. + + The active trip type can be used to control other HW to + help in cooling e.g. fans can be sped up or slowed down + + required: + - temperature + - hysteresis + - type + + additionalProperties: false + + cooling-maps: + type: object + description: + This node describes the action to be taken when a thermal zone + crosses one of the temperature thresholds described in the trips + node. The action takes the form of a mapping relation between a + trip and the target cooling device state. + + patternProperties: + "^map[0-9][-a-zA-Z0-9]*$": + type: object + + properties: + trip: + $ref: /schemas/types.yaml#/definitions/phandle + description: + A phandle of a trip point node within this thermal zone. + + cooling-device: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: + A list of cooling device phandles along with the minimum + and maximum cooling state specifiers for each cooling + device. Using the THERMAL_NO_LIMIT (-1UL) constant in the + cooling-device phandle limit specifier lets the framework + use the minimum and maximum cooling state for that cooling + device automatically. + + contribution: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 100 + description: + The contribution of the cooling devices at the trip + temperature, both referenced in this map, to this thermal + zone as a percentage. + + required: + - trip + - cooling-device + + additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/thermal/thermal.h> + + // Example 1: SDM845 TSENS + soc: soc@0 { + #address-cells = <2>; + #size-cells = <2>; + + /* ... */ + + tsens0: thermal-sensor@c263000 { + compatible = "qcom,sdm845-tsens", "qcom,tsens-v2"; + reg = <0 0x0c263000 0 0x1ff>, /* TM */ + <0 0x0c222000 0 0x1ff>; /* SROT */ + #qcom,sensors = <13>; + interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "uplow", "critical"; + #thermal-sensor-cells = <1>; + }; + + tsens1: thermal-sensor@c265000 { + compatible = "qcom,sdm845-tsens", "qcom,tsens-v2"; + reg = <0 0x0c265000 0 0x1ff>, /* TM */ + <0 0x0c223000 0 0x1ff>; /* SROT */ + #qcom,sensors = <8>; + interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 509 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "uplow", "critical"; + #thermal-sensor-cells = <1>; + }; + }; + + /* ... */ + + thermal-zones { + cpu0-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 1>; + + trips { + cpu0_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu0_alert1: trip-point1 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu0_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu0_alert0>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT + THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT + THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT + THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT + THERMAL_NO_LIMIT>; + }; + + map1 { + trip = <&cpu0_alert1>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT + THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT + THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT + THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT + THERMAL_NO_LIMIT>; + }; + }; + }; + + /* ... */ + + cluster0-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 5>; + + trips { + cluster0_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "hot"; + }; + cluster0_crit: cluster0_crit { + temperature = <110000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + /* ... */ + + gpu-thermal-top { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 11>; + + trips { + gpu1_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + }; +...
As part of moving the thermal bindings to YAML, split it up into 3 bindings: thermal sensors, cooling devices and thermal zones. The thermal-zone binding is a software abstraction to capture the properties of each zone - how often they should be checked, the temperature thresholds (trips) at which mitigation actions need to be taken and the level of mitigation needed at those thresholds. Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org> --- .../bindings/thermal/thermal-zones.yaml | 325 ++++++++++++++++++ 1 file changed, 325 insertions(+) create mode 100644 Documentation/devicetree/bindings/thermal/thermal-zones.yaml