| Message ID | 20200406101553.28958-1-a.filippov@yadro.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | ARM: DTS: Aspeed: Add YADRO Nicole BMC | expand |
On Mon, 6 Apr 2020, at 19:45, Alexander Filippov wrote: > Nicole is an OpenPower machine with an Aspeed 2500 BMC SoC manufactured > by YADRO. > > Signed-off-by: Alexander Filippov <a.filippov@yadro.com> > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/aspeed-bmc-opp-nicole.dts | 284 ++++++++++++++++++++ > 2 files changed, 285 insertions(+) > create mode 100644 arch/arm/boot/dts/aspeed-bmc-opp-nicole.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index e8dd99201397..6f9fe0f959f2 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -1347,6 +1347,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \ > aspeed-bmc-microsoft-olympus.dtb \ > aspeed-bmc-opp-lanyang.dtb \ > aspeed-bmc-opp-mihawk.dtb \ > + aspeed-bmc-opp-nicole.dtb \ > aspeed-bmc-opp-palmetto.dtb \ > aspeed-bmc-opp-romulus.dtb \ > aspeed-bmc-opp-swift.dtb \ > diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-nicole.dts > b/arch/arm/boot/dts/aspeed-bmc-opp-nicole.dts > new file mode 100644 > index 000000000000..0c8a9e7838ff > --- /dev/null > +++ b/arch/arm/boot/dts/aspeed-bmc-opp-nicole.dts > @@ -0,0 +1,284 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +// Copyright 2019 YADRO > +/dts-v1/; > +#include "aspeed-g5.dtsi" > +#include <dt-bindings/gpio/aspeed-gpio.h> > + > +/ { > + model = "Nicole BMC"; > + compatible = "yadro,nicole-bmc", "aspeed,ast2500"; > + > + chosen { > + stdout-path = &uart5; > + bootargs = "console=ttyS4,115200 earlyprintk"; > + }; > + > + memory@80000000 { > + reg = <0x80000000 0x20000000>; > + }; > + > + reserved-memory { > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; > + > + vga_memory: framebuffer@9f000000 { > + no-map; > + reg = <0x9f000000 0x01000000>; /* 16M */ > + }; > + > + flash_memory: region@98000000 { > + no-map; > + reg = <0x98000000 0x04000000>; /* 64M */ > + }; > + > + coldfire_memory: codefire_memory@9ef00000 { > + reg = <0x9ef00000 0x00100000>; > + no-map; > + }; > + > + gfx_memory: framebuffer { > + size = <0x01000000>; > + alignment = <0x01000000>; > + compatible = "shared-dma-pool"; > + reusable; > + }; > + > + video_engine_memory: jpegbuffer { > + size = <0x02000000>; /* 32M */ > + alignment = <0x01000000>; > + compatible = "shared-dma-pool"; > + reusable; > + }; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + power { > + gpios = <&gpio ASPEED_GPIO(AA, 4) GPIO_ACTIVE_HIGH>; > + }; > + > + identify { > + gpios = <&gpio ASPEED_GPIO(AA, 7) GPIO_ACTIVE_HIGH>; > + }; > + > + alarm_red { > + gpios = <&gpio ASPEED_GPIO(AA, 3) GPIO_ACTIVE_HIGH>; > + }; > + > + alarm_yellow { > + gpios = <&gpio ASPEED_GPIO(AA, 1) GPIO_ACTIVE_HIGH>; > + }; > + }; > + > + fsi: gpio-fsi { > + compatible = "aspeed,ast2500-cf-fsi-master", "fsi-master"; > + #address-cells = <2>; > + #size-cells = <0>; > + no-gpio-delays; > + > + memory-region = <&coldfire_memory>; > + aspeed,sram = <&sram>; > + aspeed,cvic = <&cvic>; > + > + clock-gpios = <&gpio ASPEED_GPIO(AA, 0) GPIO_ACTIVE_HIGH>; > + data-gpios = <&gpio ASPEED_GPIO(AA, 2) GPIO_ACTIVE_HIGH>; > + mux-gpios = <&gpio ASPEED_GPIO(A, 6) GPIO_ACTIVE_HIGH>; > + enable-gpios = <&gpio ASPEED_GPIO(D, 0) GPIO_ACTIVE_HIGH>; > + trans-gpios = <&gpio ASPEED_GPIO(P, 1) GPIO_ACTIVE_HIGH>; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + > + checkstop { > + label = "checkstop"; > + gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>; > + linux,code = <ASPEED_GPIO(J, 2)>; > + }; > + }; > +}; > + > +&fmc { > + status = "okay"; > + flash@0 { > + status = "okay"; > + m25p,fast-read; > + label = "bmc"; > + spi-max-frequency = <50000000>; > +#include "openbmc-flash-layout.dtsi" > + }; > +}; > + > +&spi1 { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_spi1_default>; > + > + flash@0 { > + status = "okay"; > + m25p,fast-read; > + label = "pnor"; > + spi-max-frequency = <100000000>; > + }; > +}; > + > +&lpc_ctrl { > + status = "okay"; > + memory-region = <&flash_memory>; > + flash = <&spi1>; > +}; > + > +&uart1 { > + /* Rear RS-232 connector */ > + status = "okay"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_txd1_default > + &pinctrl_rxd1_default > + &pinctrl_nrts1_default > + &pinctrl_ndtr1_default > + &pinctrl_ndsr1_default > + &pinctrl_ncts1_default > + &pinctrl_ndcd1_default > + &pinctrl_nri1_default>; > +}; > + > +&uart5 { > + status = "okay"; > +}; > + > +&mac0 { > + status = "okay"; > + > + use-ncsi; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_rmii1_default>; > + clocks = <&syscon ASPEED_CLK_GATE_MAC1CLK>, > + <&syscon ASPEED_CLK_MAC1RCLK>; > + clock-names = "MACCLK", "RCLK"; > +}; > + > +&i2c0 { > + status = "okay"; > + > + eeprom@50 { > + compatible = "atmel,24c256"; > + reg = <0x50>; > + pagesize = <64>; > + }; > +}; > + > +&i2c1 { > + status = "okay"; > +}; > + > +&i2c2 { > + status = "okay"; > +}; > + > +&i2c3 { > + status = "okay"; > +}; > + > +&i2c4 { > + status = "okay"; > +}; > + > +&i2c5 { > + status = "okay"; > +}; > + > +&i2c6 { > + status = "okay"; > + > + rtc@32 { > + compatible = "epson,rx8900"; > + reg = <0x32>; > + }; > +}; > + > +&i2c7 { > + status = "okay"; > +}; > + > +&i2c8 { > + status = "okay"; > +}; > + > +&i2c9 { > + status = "okay"; > +}; > + > +&i2c10 { > + status = "okay"; > +}; > + > +&i2c11 { > + status = "okay"; > +}; > + > +&i2c12 { > + status = "okay"; > +}; Are you accessing devices on the busses from userspace? It would be helpful to comment here why you're enabling all of these busses but not describing any devices on them, if it's necessary to enable them at all. > + > +&gpio { > + nic_func_mode0 { > + gpio-hog; > + gpios = <ASPEED_GPIO(D, 3) GPIO_ACTIVE_HIGH>; > + output-low; > + line-name = "nic_func_mode0"; > + }; > + nic_func_mode1 { > + gpio-hog; > + gpios = <ASPEED_GPIO(D, 4) GPIO_ACTIVE_HIGH>; > + output-low; > + line-name = "nic_func_mode1"; > + }; > + seq_cont { > + gpio-hog; > + gpios = <ASPEED_GPIO(S, 7) GPIO_ACTIVE_HIGH>; > + output-low; > + line-name = "seq_cont"; > + }; > + ncsi_cfg { > + gpio-hog; > + input; > + gpios = <ASPEED_GPIO(E, 1) GPIO_ACTIVE_HIGH>; > + line-name = "ncsi_cfg"; > + }; > +}; > + > +&vuart { > + status = "okay"; > +}; > + > +&gfx { > + status = "okay"; > + memory-region = <&gfx_memory>; > +}; > + > +&pinctrl { > + aspeed,external-nodes = <&gfx &lhc>; > +}; > + > +&ibt { > + status = "okay"; > +}; > + > +&vhub { > + status = "okay"; > +}; > + > +&adc { > + status = "okay"; You should specify the pinmux configuration for the channels you're using to ensure exclusive access to those pins (otherwise they could be exported e.g. as GPIOs). Andrew
On Fri, Apr 10, 2020 at 02:29:47PM +0930, Andrew Jeffery wrote: > > > > +&i2c11 { > > + status = "okay"; > > +}; > > + > > +&i2c12 { > > + status = "okay"; > > +}; > > Are you accessing devices on the busses from userspace? It would > be helpful to comment here why you're enabling all of these busses > but not describing any devices on them, if it's necessary to enable > them at all. > Yes, some of them are unused and may be removed. For others I'll add comments in the next version. > > + > > +&adc { > > + status = "okay"; > > You should specify the pinmux configuration for the channels you're using > to ensure exclusive access to those pins (otherwise they could be exported > e.g. as GPIOs). It was just copied from Romulus and looks like I missed iio-hwmon-battery. Is it what you meant? All other pins are wired to the ground.` Alexander
On Sat, 11 Apr 2020, at 00:29, Alexander A. Filippov wrote: > On Fri, Apr 10, 2020 at 02:29:47PM +0930, Andrew Jeffery wrote: > > > > > > > +&i2c11 { > > > + status = "okay"; > > > +}; > > > + > > > +&i2c12 { > > > + status = "okay"; > > > +}; > > > > Are you accessing devices on the busses from userspace? It would > > be helpful to comment here why you're enabling all of these busses > > but not describing any devices on them, if it's necessary to enable > > them at all. > > > > Yes, some of them are unused and may be removed. > For others I'll add comments in the next version. > > > > + > > > +&adc { > > > + status = "okay"; > > > > You should specify the pinmux configuration for the channels you're using > > to ensure exclusive access to those pins (otherwise they could be exported > > e.g. as GPIOs). > > It was just copied from Romulus and looks like I missed iio-hwmon-battery. > Is it what you meant? The Romulus devicetree may need to be fixed too :) Andrew
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index e8dd99201397..6f9fe0f959f2 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -1347,6 +1347,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \ aspeed-bmc-microsoft-olympus.dtb \ aspeed-bmc-opp-lanyang.dtb \ aspeed-bmc-opp-mihawk.dtb \ + aspeed-bmc-opp-nicole.dtb \ aspeed-bmc-opp-palmetto.dtb \ aspeed-bmc-opp-romulus.dtb \ aspeed-bmc-opp-swift.dtb \ diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-nicole.dts b/arch/arm/boot/dts/aspeed-bmc-opp-nicole.dts new file mode 100644 index 000000000000..0c8a9e7838ff --- /dev/null +++ b/arch/arm/boot/dts/aspeed-bmc-opp-nicole.dts @@ -0,0 +1,284 @@ +// SPDX-License-Identifier: GPL-2.0+ +// Copyright 2019 YADRO +/dts-v1/; +#include "aspeed-g5.dtsi" +#include <dt-bindings/gpio/aspeed-gpio.h> + +/ { + model = "Nicole BMC"; + compatible = "yadro,nicole-bmc", "aspeed,ast2500"; + + chosen { + stdout-path = &uart5; + bootargs = "console=ttyS4,115200 earlyprintk"; + }; + + memory@80000000 { + reg = <0x80000000 0x20000000>; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + vga_memory: framebuffer@9f000000 { + no-map; + reg = <0x9f000000 0x01000000>; /* 16M */ + }; + + flash_memory: region@98000000 { + no-map; + reg = <0x98000000 0x04000000>; /* 64M */ + }; + + coldfire_memory: codefire_memory@9ef00000 { + reg = <0x9ef00000 0x00100000>; + no-map; + }; + + gfx_memory: framebuffer { + size = <0x01000000>; + alignment = <0x01000000>; + compatible = "shared-dma-pool"; + reusable; + }; + + video_engine_memory: jpegbuffer { + size = <0x02000000>; /* 32M */ + alignment = <0x01000000>; + compatible = "shared-dma-pool"; + reusable; + }; + }; + + leds { + compatible = "gpio-leds"; + + power { + gpios = <&gpio ASPEED_GPIO(AA, 4) GPIO_ACTIVE_HIGH>; + }; + + identify { + gpios = <&gpio ASPEED_GPIO(AA, 7) GPIO_ACTIVE_HIGH>; + }; + + alarm_red { + gpios = <&gpio ASPEED_GPIO(AA, 3) GPIO_ACTIVE_HIGH>; + }; + + alarm_yellow { + gpios = <&gpio ASPEED_GPIO(AA, 1) GPIO_ACTIVE_HIGH>; + }; + }; + + fsi: gpio-fsi { + compatible = "aspeed,ast2500-cf-fsi-master", "fsi-master"; + #address-cells = <2>; + #size-cells = <0>; + no-gpio-delays; + + memory-region = <&coldfire_memory>; + aspeed,sram = <&sram>; + aspeed,cvic = <&cvic>; + + clock-gpios = <&gpio ASPEED_GPIO(AA, 0) GPIO_ACTIVE_HIGH>; + data-gpios = <&gpio ASPEED_GPIO(AA, 2) GPIO_ACTIVE_HIGH>; + mux-gpios = <&gpio ASPEED_GPIO(A, 6) GPIO_ACTIVE_HIGH>; + enable-gpios = <&gpio ASPEED_GPIO(D, 0) GPIO_ACTIVE_HIGH>; + trans-gpios = <&gpio ASPEED_GPIO(P, 1) GPIO_ACTIVE_HIGH>; + }; + + gpio-keys { + compatible = "gpio-keys"; + + checkstop { + label = "checkstop"; + gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>; + linux,code = <ASPEED_GPIO(J, 2)>; + }; + }; +}; + +&fmc { + status = "okay"; + flash@0 { + status = "okay"; + m25p,fast-read; + label = "bmc"; + spi-max-frequency = <50000000>; +#include "openbmc-flash-layout.dtsi" + }; +}; + +&spi1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi1_default>; + + flash@0 { + status = "okay"; + m25p,fast-read; + label = "pnor"; + spi-max-frequency = <100000000>; + }; +}; + +&lpc_ctrl { + status = "okay"; + memory-region = <&flash_memory>; + flash = <&spi1>; +}; + +&uart1 { + /* Rear RS-232 connector */ + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_txd1_default + &pinctrl_rxd1_default + &pinctrl_nrts1_default + &pinctrl_ndtr1_default + &pinctrl_ndsr1_default + &pinctrl_ncts1_default + &pinctrl_ndcd1_default + &pinctrl_nri1_default>; +}; + +&uart5 { + status = "okay"; +}; + +&mac0 { + status = "okay"; + + use-ncsi; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rmii1_default>; + clocks = <&syscon ASPEED_CLK_GATE_MAC1CLK>, + <&syscon ASPEED_CLK_MAC1RCLK>; + clock-names = "MACCLK", "RCLK"; +}; + +&i2c0 { + status = "okay"; + + eeprom@50 { + compatible = "atmel,24c256"; + reg = <0x50>; + pagesize = <64>; + }; +}; + +&i2c1 { + status = "okay"; +}; + +&i2c2 { + status = "okay"; +}; + +&i2c3 { + status = "okay"; +}; + +&i2c4 { + status = "okay"; +}; + +&i2c5 { + status = "okay"; +}; + +&i2c6 { + status = "okay"; + + rtc@32 { + compatible = "epson,rx8900"; + reg = <0x32>; + }; +}; + +&i2c7 { + status = "okay"; +}; + +&i2c8 { + status = "okay"; +}; + +&i2c9 { + status = "okay"; +}; + +&i2c10 { + status = "okay"; +}; + +&i2c11 { + status = "okay"; +}; + +&i2c12 { + status = "okay"; +}; + +&gpio { + nic_func_mode0 { + gpio-hog; + gpios = <ASPEED_GPIO(D, 3) GPIO_ACTIVE_HIGH>; + output-low; + line-name = "nic_func_mode0"; + }; + nic_func_mode1 { + gpio-hog; + gpios = <ASPEED_GPIO(D, 4) GPIO_ACTIVE_HIGH>; + output-low; + line-name = "nic_func_mode1"; + }; + seq_cont { + gpio-hog; + gpios = <ASPEED_GPIO(S, 7) GPIO_ACTIVE_HIGH>; + output-low; + line-name = "seq_cont"; + }; + ncsi_cfg { + gpio-hog; + input; + gpios = <ASPEED_GPIO(E, 1) GPIO_ACTIVE_HIGH>; + line-name = "ncsi_cfg"; + }; +}; + +&vuart { + status = "okay"; +}; + +&gfx { + status = "okay"; + memory-region = <&gfx_memory>; +}; + +&pinctrl { + aspeed,external-nodes = <&gfx &lhc>; +}; + +&ibt { + status = "okay"; +}; + +&vhub { + status = "okay"; +}; + +&adc { + status = "okay"; +}; + +&video { + status = "okay"; + memory-region = <&video_engine_memory>; +}; + +#include "ibm-power9-dual.dtsi"
Nicole is an OpenPower machine with an Aspeed 2500 BMC SoC manufactured by YADRO. Signed-off-by: Alexander Filippov <a.filippov@yadro.com> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/aspeed-bmc-opp-nicole.dts | 284 ++++++++++++++++++++ 2 files changed, 285 insertions(+) create mode 100644 arch/arm/boot/dts/aspeed-bmc-opp-nicole.dts