deleted file mode 100644
@@ -1,87 +0,0 @@
-SN65DSI86 DSI to eDP bridge chip
---------------------------------
-
-This is the binding for Texas Instruments SN65DSI86 bridge.
-http://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=sn65dsi86&fileType=pdf
-
-Required properties:
-- compatible: Must be "ti,sn65dsi86"
-- reg: i2c address of the chip, 0x2d as per datasheet
-- enable-gpios: gpio specification for bridge_en pin (active high)
-
-- vccio-supply: A 1.8V supply that powers up the digital IOs.
-- vpll-supply: A 1.8V supply that powers up the displayport PLL.
-- vcca-supply: A 1.2V supply that powers up the analog circuits.
-- vcc-supply: A 1.2V supply that powers up the digital core.
-
-Optional properties:
-- interrupts-extended: Specifier for the SN65DSI86 interrupt line.
-
-- gpio-controller: Marks the device has a GPIO controller.
-- #gpio-cells : Should be two. The first cell is the pin number and
- the second cell is used to specify flags.
- See ../../gpio/gpio.txt for more information.
-- #pwm-cells : Should be one. See ../../pwm/pwm.yaml for description of
- the cell formats.
-
-- clock-names: should be "refclk"
-- clocks: Specification for input reference clock. The reference
- clock rate must be 12 MHz, 19.2 MHz, 26 MHz, 27 MHz or 38.4 MHz.
-
-- data-lanes: See ../../media/video-interface.txt
-- lane-polarities: See ../../media/video-interface.txt
-
-- suspend-gpios: specification for GPIO1 pin on bridge (active low)
-
-Required nodes:
-This device has two video ports. Their connections are modelled using the
-OF graph bindings specified in Documentation/devicetree/bindings/graph.txt.
-
-- Video port 0 for DSI input
-- Video port 1 for eDP output
-
-Example
--------
-
-edp-bridge@2d {
- compatible = "ti,sn65dsi86";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x2d>;
-
- enable-gpios = <&msmgpio 33 GPIO_ACTIVE_HIGH>;
- suspend-gpios = <&msmgpio 34 GPIO_ACTIVE_LOW>;
-
- interrupts-extended = <&gpio3 4 IRQ_TYPE_EDGE_FALLING>;
-
- vccio-supply = <&pm8916_l17>;
- vcca-supply = <&pm8916_l6>;
- vpll-supply = <&pm8916_l17>;
- vcc-supply = <&pm8916_l6>;
-
- clock-names = "refclk";
- clocks = <&input_refclk>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
-
- edp_bridge_in: endpoint {
- remote-endpoint = <&dsi_out>;
- };
- };
-
- port@1 {
- reg = <1>;
-
- edp_bridge_out: endpoint {
- data-lanes = <2 1 3 0>;
- lane-polarities = <0 1 0 1>;
- remote-endpoint = <&edp_panel_in>;
- };
- };
- };
-}
new file mode 100644
@@ -0,0 +1,285 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/ti,sn65dsi86.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: SN65DSI86 DSI to eDP bridge chip
+
+maintainers:
+ - Sandeep Panda <spanda@codeaurora.org>
+
+description: |
+ The Texas Instruments SN65DSI86 bridge takes MIPI DSI in and outputs eDP.
+ http://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=sn65dsi86&fileType=pdf
+
+properties:
+ compatible:
+ const: ti,sn65dsi86
+
+ reg:
+ const: 0x2d
+
+ enable-gpios:
+ maxItems: 1
+ description: GPIO specifier for bridge_en pin (active high).
+
+ suspend-gpios:
+ maxItems: 1
+ description: GPIO specifier for GPIO1 pin on bridge (active low).
+
+ vccio-supply:
+ description: A 1.8V supply that powers the digital IOs.
+
+ vpll-supply:
+ description: A 1.8V supply that powers the DisplayPort PLL.
+
+ vcca-supply:
+ description: A 1.2V supply that powers the analog circuits.
+
+ vcc-supply:
+ description: A 1.2V supply that powers the digital core.
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+ description:
+ Clock specifier for input reference clock. The reference clock rate must
+ be 12 MHz, 19.2 MHz, 26 MHz, 27 MHz or 38.4 MHz.
+
+ clock-names:
+ const: refclk
+
+ gpio-controller: true
+ '#gpio-cells':
+ const: 2
+ description:
+ First cell is pin number, second cell is flags. GPIO pin numbers are
+ 1-based to match the datasheet. See ../../gpio/gpio.txt for more
+ information.
+
+ '#pwm-cells':
+ const: 1
+ description: See ../../pwm/pwm.yaml for description of the cell formats.
+
+ ports:
+ type: object
+ additionalProperties: false
+
+ properties:
+ "#address-cells":
+ const: 1
+
+ "#size-cells":
+ const: 0
+
+ port@0:
+ type: object
+ additionalProperties: false
+
+ description:
+ Video port for MIPI DSI input
+
+ properties:
+ reg:
+ const: 0
+
+ endpoint:
+ type: object
+ additionalProperties: false
+ properties:
+ remote-endpoint: true
+
+ required:
+ - reg
+
+ port@1:
+ type: object
+ additionalProperties: false
+
+ description:
+ Video port for eDP output (panel or connector).
+
+ properties:
+ reg:
+ const: 1
+
+ endpoint:
+ type: object
+ additionalProperties: false
+
+ properties:
+ remote-endpoint: true
+
+ data-lanes:
+ oneOf:
+ - minItems: 1
+ maxItems: 1
+ uniqueItems: true
+ items:
+ enum:
+ - 0
+ - 1
+ description:
+ If you have 1 logical lane the bridge supports routing
+ to either port 0 or port 1. Port 0 is suggested.
+ See ../../media/video-interface.txt for details.
+
+ - minItems: 2
+ maxItems: 2
+ uniqueItems: true
+ items:
+ enum:
+ - 0
+ - 1
+ description:
+ If you have 2 logical lanes the bridge supports
+ reordering but only on physical ports 0 and 1.
+ See ../../media/video-interface.txt for details.
+
+ - minItems: 4
+ maxItems: 4
+ uniqueItems: true
+ items:
+ enum:
+ - 0
+ - 1
+ - 2
+ - 3
+ description:
+ If you have 4 logical lanes the bridge supports
+ reordering in any way.
+ See ../../media/video-interface.txt for details.
+
+ lane-polarities:
+ minItems: 1
+ maxItems: 4
+ items:
+ enum:
+ - 0
+ - 1
+ description: See ../../media/video-interface.txt
+
+ dependencies:
+ lane-polarities: [data-lanes]
+
+ required:
+ - reg
+
+ required:
+ - "#address-cells"
+ - "#size-cells"
+ - port@0
+ - port@1
+
+required:
+ - compatible
+ - reg
+ - enable-gpios
+ - vccio-supply
+ - vpll-supply
+ - vcca-supply
+ - vcc-supply
+ - ports
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/qcom,rpmh.h>
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bridge@2d {
+ compatible = "ti,sn65dsi86";
+ reg = <0x2d>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <10 IRQ_TYPE_LEVEL_HIGH>;
+
+ enable-gpios = <&tlmm 102 GPIO_ACTIVE_HIGH>;
+
+ vpll-supply = <&src_pp1800_s4a>;
+ vccio-supply = <&src_pp1800_s4a>;
+ vcca-supply = <&src_pp1200_l2a>;
+ vcc-supply = <&src_pp1200_l2a>;
+
+ clocks = <&rpmhcc RPMH_LN_BB_CLK2>;
+ clock-names = "refclk";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ endpoint {
+ remote-endpoint = <&dsi0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ endpoint {
+ remote-endpoint = <&panel_in_edp>;
+ };
+ };
+ };
+ };
+ };
+ - |
+ #include <dt-bindings/clock/qcom,rpmh.h>
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bridge@2d {
+ compatible = "ti,sn65dsi86";
+ reg = <0x2d>;
+
+ enable-gpios = <&msmgpio 33 GPIO_ACTIVE_HIGH>;
+ suspend-gpios = <&msmgpio 34 GPIO_ACTIVE_LOW>;
+
+ interrupts-extended = <&gpio3 4 IRQ_TYPE_EDGE_FALLING>;
+
+ vccio-supply = <&pm8916_l17>;
+ vcca-supply = <&pm8916_l6>;
+ vpll-supply = <&pm8916_l17>;
+ vcc-supply = <&pm8916_l6>;
+
+ clock-names = "refclk";
+ clocks = <&input_refclk>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ edp_bridge_in: endpoint {
+ remote-endpoint = <&dsi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ edp_bridge_out: endpoint {
+ data-lanes = <2 1 3 0>;
+ lane-polarities = <0 1 0 1>;
+ remote-endpoint = <&edp_panel_in>;
+ };
+ };
+ };
+ };
+ };
This moves the bindings over, based a lot on toshiba,tc358768.yaml. Unless there's someone known to be better, I've set the maintainer in the yaml as the first person to submit bindings. Signed-off-by: Douglas Anderson <dianders@chromium.org> --- I removed Stephen's review tag on v5 since I squashed in a bunch of other stuff. Changes in v5: - Squash https://lore.kernel.org/r/20200506140208.v2.2.I0a2bca02b09c1fcb6b09479b489736d600b3e57f@changeid/ Changes in v4: None Changes in v3: None Changes in v2: - specification => specifier. - power up => power. - Added back missing suspend-gpios. - data-lanes and lane-polarities are are the right place now. - endpoints don't need to be patternProperties. - Specified more details for data-lanes and lane-polarities. - Added old example back in, fixing bugs in it. - Example i2c bus is just called "i2c", not "i2c1" now. .../bindings/display/bridge/ti,sn65dsi86.txt | 87 ------ .../bindings/display/bridge/ti,sn65dsi86.yaml | 285 ++++++++++++++++++ 2 files changed, 285 insertions(+), 87 deletions(-) delete mode 100644 Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt create mode 100644 Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.yaml