Message ID | 20200601184223.1.I281c81384150e8fefbebf32fa79cb091d0311208@changeid (mailing list archive) |
---|---|
State | Accepted |
Delegated to: | Marcel Holtmann |
Headers | show |
Series | Bluetooth: Check scan state before disabling during suspend | expand |
Hey linux-bluetooth, We found this bug when reverting some Chromium maintained patches in our repository that was conditionally dropping LE scan enable commands if it wasn't toggling between true/false. On some Intel controllers, disabling LE scan when it's already disabled resulted in a "Command Disallowed" and this was causing suspend to fail. On Mon, Jun 1, 2020 at 6:43 PM Manish Mandlik <mmandlik@google.com> wrote: > > Check current scan state by checking HCI_LE_SCAN flag and send scan > disable command only if scan is already enabled. > > Signed-off-by: Manish Mandlik <mmandlik@google.com> > --- > > net/bluetooth/hci_request.c | 10 ++++++---- > 1 file changed, 6 insertions(+), 4 deletions(-) > > diff --git a/net/bluetooth/hci_request.c b/net/bluetooth/hci_request.c > index 1fc55685da62d..1acf5b8e0910c 100644 > --- a/net/bluetooth/hci_request.c > +++ b/net/bluetooth/hci_request.c > @@ -998,8 +998,9 @@ static void hci_req_set_event_filter(struct hci_request *req) > > static void hci_req_config_le_suspend_scan(struct hci_request *req) > { > - /* Can't change params without disabling first */ > - hci_req_add_le_scan_disable(req); > + /* Before changing params disable scan if enabled */ > + if (hci_dev_test_flag(req->hdev, HCI_LE_SCAN)) > + hci_req_add_le_scan_disable(req); > > /* Configure params and enable scanning */ > hci_req_add_le_passive_scan(req); > @@ -1065,8 +1066,9 @@ void hci_req_prepare_suspend(struct hci_dev *hdev, enum suspended_state next) > page_scan = SCAN_DISABLED; > hci_req_add(&req, HCI_OP_WRITE_SCAN_ENABLE, 1, &page_scan); > > - /* Disable LE passive scan */ > - hci_req_add_le_scan_disable(&req); > + /* Disable LE passive scan if enabled */ > + if (hci_dev_test_flag(hdev, HCI_LE_SCAN)) > + hci_req_add_le_scan_disable(&req); > > /* Mark task needing completion */ > set_bit(SUSPEND_SCAN_DISABLE, hdev->suspend_tasks); > -- > 2.27.0.rc2.251.g90737beb825-goog > Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
On Mon, Jun 1, 2020 at 9:49 PM Abhishek Pandit-Subedi <abhishekpandit@chromium.org> wrote: > > Hey linux-bluetooth, > > We found this bug when reverting some Chromium maintained patches in > our repository that was conditionally dropping LE scan enable commands > if it wasn't toggling between true/false. On some Intel controllers, > disabling LE scan when it's already disabled resulted in a "Command > Disallowed" and this was causing suspend to fail. > > On Mon, Jun 1, 2020 at 6:43 PM Manish Mandlik <mmandlik@google.com> wrote: > > > > Check current scan state by checking HCI_LE_SCAN flag and send scan > > disable command only if scan is already enabled. > > > > Signed-off-by: Manish Mandlik <mmandlik@google.com> > > --- > > > > net/bluetooth/hci_request.c | 10 ++++++---- > > 1 file changed, 6 insertions(+), 4 deletions(-) > > > > diff --git a/net/bluetooth/hci_request.c b/net/bluetooth/hci_request.c > > index 1fc55685da62d..1acf5b8e0910c 100644 > > --- a/net/bluetooth/hci_request.c > > +++ b/net/bluetooth/hci_request.c > > @@ -998,8 +998,9 @@ static void hci_req_set_event_filter(struct hci_request *req) > > > > static void hci_req_config_le_suspend_scan(struct hci_request *req) > > { > > - /* Can't change params without disabling first */ > > - hci_req_add_le_scan_disable(req); > > + /* Before changing params disable scan if enabled */ > > + if (hci_dev_test_flag(req->hdev, HCI_LE_SCAN)) > > + hci_req_add_le_scan_disable(req); > > > > /* Configure params and enable scanning */ > > hci_req_add_le_passive_scan(req); > > @@ -1065,8 +1066,9 @@ void hci_req_prepare_suspend(struct hci_dev *hdev, enum suspended_state next) > > page_scan = SCAN_DISABLED; > > hci_req_add(&req, HCI_OP_WRITE_SCAN_ENABLE, 1, &page_scan); > > > > - /* Disable LE passive scan */ > > - hci_req_add_le_scan_disable(&req); > > + /* Disable LE passive scan if enabled */ > > + if (hci_dev_test_flag(hdev, HCI_LE_SCAN)) > > + hci_req_add_le_scan_disable(&req); > > > > /* Mark task needing completion */ > > set_bit(SUSPEND_SCAN_DISABLE, hdev->suspend_tasks); > > -- > > 2.27.0.rc2.251.g90737beb825-goog > > > > Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org> Reviewed-by: Alain Michaud <alainm@chromium.org> > > -- > You received this message because you are subscribed to the Google Groups "ChromeOS Bluetooth Upstreaming" group. > To unsubscribe from this group and stop receiving emails from it, send an email to chromeos-bluetooth-upstreaming+unsubscribe@chromium.org. > To post to this group, send email to chromeos-bluetooth-upstreaming@chromium.org. > To view this discussion on the web visit https://groups.google.com/a/chromium.org/d/msgid/chromeos-bluetooth-upstreaming/CANFp7mXDvdicvyEpU-oDu4fBj92nQ7SENVdd_rG9TFQkqDevZg%40mail.gmail.com.
Hi Manish, > Check current scan state by checking HCI_LE_SCAN flag and send scan > disable command only if scan is already enabled. > > Signed-off-by: Manish Mandlik <mmandlik@google.com> > --- > > net/bluetooth/hci_request.c | 10 ++++++---- > 1 file changed, 6 insertions(+), 4 deletions(-) patch has been applied to bluetooth-next tree. Regards Marcel
diff --git a/net/bluetooth/hci_request.c b/net/bluetooth/hci_request.c index 1fc55685da62d..1acf5b8e0910c 100644 --- a/net/bluetooth/hci_request.c +++ b/net/bluetooth/hci_request.c @@ -998,8 +998,9 @@ static void hci_req_set_event_filter(struct hci_request *req) static void hci_req_config_le_suspend_scan(struct hci_request *req) { - /* Can't change params without disabling first */ - hci_req_add_le_scan_disable(req); + /* Before changing params disable scan if enabled */ + if (hci_dev_test_flag(req->hdev, HCI_LE_SCAN)) + hci_req_add_le_scan_disable(req); /* Configure params and enable scanning */ hci_req_add_le_passive_scan(req); @@ -1065,8 +1066,9 @@ void hci_req_prepare_suspend(struct hci_dev *hdev, enum suspended_state next) page_scan = SCAN_DISABLED; hci_req_add(&req, HCI_OP_WRITE_SCAN_ENABLE, 1, &page_scan); - /* Disable LE passive scan */ - hci_req_add_le_scan_disable(&req); + /* Disable LE passive scan if enabled */ + if (hci_dev_test_flag(hdev, HCI_LE_SCAN)) + hci_req_add_le_scan_disable(&req); /* Mark task needing completion */ set_bit(SUSPEND_SCAN_DISABLE, hdev->suspend_tasks);
Check current scan state by checking HCI_LE_SCAN flag and send scan disable command only if scan is already enabled. Signed-off-by: Manish Mandlik <mmandlik@google.com> --- net/bluetooth/hci_request.c | 10 ++++++---- 1 file changed, 6 insertions(+), 4 deletions(-)