diff mbox series

[v10,06/20] dt-bindings: mtd: Document nand-ecc-engine

Message ID 20200603175759.19948-7-miquel.raynal@bootlin.com (mailing list archive)
State New, archived
Headers show
Series Introduction of the generic ECC framework | expand

Commit Message

Miquel Raynal June 3, 2020, 5:57 p.m. UTC
This property is needed to precisely point to the hardware ECC engine
to use when there are several of them available. Here, hardware also
refers to the on-die possibility.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 .../devicetree/bindings/mtd/nand-controller.yaml     | 12 ++++++++++++
 1 file changed, 12 insertions(+)

Comments

Rob Herring June 3, 2020, 10:16 p.m. UTC | #1
On Wed, 03 Jun 2020 19:57:45 +0200, Miquel Raynal wrote:
> This property is needed to precisely point to the hardware ECC engine
> to use when there are several of them available. Here, hardware also
> refers to the on-die possibility.
> 
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> ---
>  .../devicetree/bindings/mtd/nand-controller.yaml     | 12 ++++++++++++
>  1 file changed, 12 insertions(+)
> 


My bot found errors running 'make dt_binding_check' on your patch:

Documentation/devicetree/bindings/mtd/nand-controller.yaml:  while scanning for the next token
found character that cannot start any token
  in "<unicode string>", line 62, column 1
Documentation/devicetree/bindings/Makefile:12: recipe for target 'Documentation/devicetree/bindings/mtd/nand-controller.example.dts' failed
make[1]: *** [Documentation/devicetree/bindings/mtd/nand-controller.example.dts] Error 1
make[1]: *** Waiting for unfinished jobs....
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/mtd/nand-controller.yaml: ignoring, error parsing file
warning: no schema found in file: ./Documentation/devicetree/bindings/mtd/nand-controller.yaml
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/mtd/nand-controller.yaml: ignoring, error parsing file
warning: no schema found in file: ./Documentation/devicetree/bindings/mtd/nand-controller.yaml
Makefile:1300: recipe for target 'dt_binding_check' failed
make: *** [dt_binding_check] Error 2

See https://patchwork.ozlabs.org/patch/1303116

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure dt-schema is up to date:

pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade

Please check and re-submit.
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/mtd/nand-controller.yaml b/Documentation/devicetree/bindings/mtd/nand-controller.yaml
index 4a0798247d2d..0969d2e6720b 100644
--- a/Documentation/devicetree/bindings/mtd/nand-controller.yaml
+++ b/Documentation/devicetree/bindings/mtd/nand-controller.yaml
@@ -56,6 +56,18 @@  patternProperties:
           (Linux will handle the calculations). soft_bch is deprecated
           and should be replaced by soft and nand-ecc-algo.
 
+      nand-ecc-engine:
+        maxItems: 1
+        description:
+	  A phandle on the hardware ECC engine if any. There are
+          basically three possibilities:
+          1/ The ECC engine is part of the NAND controller, in this
+          case the phandle should reference the parent node.
+          2/ The ECC engine is part of the NAND part (on-die), in this
+          case the phandle should reference the node itself.
+          3/ The ECC engine is external, in this case the phandle should
+          reference the specific ECC engine node.
+
       nand-ecc-placement:
         allOf:
           - $ref: /schemas/types.yaml#/definitions/string