| Message ID | 20200701130129.30961-2-benjamin.gaignard@st.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | DCMI set minimum cpufreq requirement | expand |
On Wed, Jul 01, 2020 at 03:01:27PM +0200, Benjamin Gaignard wrote: > Document st,stm32-dcmi-min-frequency property which is used to > request CPUs minimum frequency when streaming frames. > > Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com> > --- > Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml | 8 ++++++++ > 1 file changed, 8 insertions(+) > > diff --git a/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml b/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml > index 3fe778cb5cc3..05ca85a2411a 100644 > --- a/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml > +++ b/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml > @@ -44,6 +44,13 @@ properties: > bindings defined in > Documentation/devicetree/bindings/media/video-interfaces.txt. > > + st,stm32-dcmi-min-frequency: > + description: DCMI minimum CPUs frequency requirement (in KHz). > + allOf: > + - $ref: /schemas/types.yaml#/definitions/uint32 > + - minimum: 0 > + - default: 0 I think this is questionable to be in DT and if it is, it's something that's hardly specific to ST or this block. IIRC, we already have a way to specify minimum OPPs. Rob
On 7/9/20 10:37 PM, Rob Herring wrote: > On Wed, Jul 01, 2020 at 03:01:27PM +0200, Benjamin Gaignard wrote: >> Document st,stm32-dcmi-min-frequency property which is used to >> request CPUs minimum frequency when streaming frames. >> >> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com> >> --- >> Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml | 8 ++++++++ >> 1 file changed, 8 insertions(+) >> >> diff --git a/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml b/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml >> index 3fe778cb5cc3..05ca85a2411a 100644 >> --- a/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml >> +++ b/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml >> @@ -44,6 +44,13 @@ properties: >> bindings defined in >> Documentation/devicetree/bindings/media/video-interfaces.txt. >> >> + st,stm32-dcmi-min-frequency: >> + description: DCMI minimum CPUs frequency requirement (in KHz). >> + allOf: >> + - $ref: /schemas/types.yaml#/definitions/uint32 >> + - minimum: 0 >> + - default: 0 > I think this is questionable to be in DT and if it is, it's something > that's hardly specific to ST or this block. IIRC, we already have a way > to specify minimum OPPs. This binding is only needed on some STM32 SoC when DVFS is activated with low frequency setting in opp. The value also depends of the targeted video format and framerate. It is not an opp because it doesn't define a voltage-current-frequency combination but only set a minimum target for the CPUs frequency to guaranty a good reaction time when handling IRQs for the sensor. Benjamin > > Rob
On Fri, Jul 10, 2020 at 1:33 AM Benjamin GAIGNARD <benjamin.gaignard@st.com> wrote: > > > > On 7/9/20 10:37 PM, Rob Herring wrote: > > On Wed, Jul 01, 2020 at 03:01:27PM +0200, Benjamin Gaignard wrote: > >> Document st,stm32-dcmi-min-frequency property which is used to > >> request CPUs minimum frequency when streaming frames. > >> > >> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com> > >> --- > >> Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml | 8 ++++++++ > >> 1 file changed, 8 insertions(+) > >> > >> diff --git a/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml b/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml > >> index 3fe778cb5cc3..05ca85a2411a 100644 > >> --- a/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml > >> +++ b/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml > >> @@ -44,6 +44,13 @@ properties: > >> bindings defined in > >> Documentation/devicetree/bindings/media/video-interfaces.txt. > >> > >> + st,stm32-dcmi-min-frequency: > >> + description: DCMI minimum CPUs frequency requirement (in KHz). > >> + allOf: > >> + - $ref: /schemas/types.yaml#/definitions/uint32 > >> + - minimum: 0 > >> + - default: 0 > > I think this is questionable to be in DT and if it is, it's something > > that's hardly specific to ST or this block. IIRC, we already have a way > > to specify minimum OPPs. > This binding is only needed on some STM32 SoC when DVFS is activated > with low frequency setting in opp. The value also depends of the targeted > video format and framerate. As those 2 things are not in the DT, then neither should this value be. > It is not an opp because it doesn't define a voltage-current-frequency > combination > but only set a minimum target for the CPUs frequency to guaranty a good > reaction > time when handling IRQs for the sensor. OPPs can be frequency only. This is pretty clearly defining the CPU must Operate at a certain minimum Performance Point. Rob
On 7/10/20 10:01 PM, Rob Herring wrote: > On Fri, Jul 10, 2020 at 1:33 AM Benjamin GAIGNARD > <benjamin.gaignard@st.com> wrote: >> >> >> On 7/9/20 10:37 PM, Rob Herring wrote: >>> On Wed, Jul 01, 2020 at 03:01:27PM +0200, Benjamin Gaignard wrote: >>>> Document st,stm32-dcmi-min-frequency property which is used to >>>> request CPUs minimum frequency when streaming frames. >>>> >>>> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com> >>>> --- >>>> Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml | 8 ++++++++ >>>> 1 file changed, 8 insertions(+) >>>> >>>> diff --git a/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml b/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml >>>> index 3fe778cb5cc3..05ca85a2411a 100644 >>>> --- a/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml >>>> +++ b/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml >>>> @@ -44,6 +44,13 @@ properties: >>>> bindings defined in >>>> Documentation/devicetree/bindings/media/video-interfaces.txt. >>>> >>>> + st,stm32-dcmi-min-frequency: >>>> + description: DCMI minimum CPUs frequency requirement (in KHz). >>>> + allOf: >>>> + - $ref: /schemas/types.yaml#/definitions/uint32 >>>> + - minimum: 0 >>>> + - default: 0 >>> I think this is questionable to be in DT and if it is, it's something >>> that's hardly specific to ST or this block. IIRC, we already have a way >>> to specify minimum OPPs. >> This binding is only needed on some STM32 SoC when DVFS is activated >> with low frequency setting in opp. The value also depends of the targeted >> video format and framerate. > As those 2 things are not in the DT, then neither should this value be. > >> It is not an opp because it doesn't define a voltage-current-frequency >> combination >> but only set a minimum target for the CPUs frequency to guaranty a good >> reaction >> time when handling IRQs for the sensor. > OPPs can be frequency only. This is pretty clearly defining the CPU > must Operate at a certain minimum Performance Point. Hi Rob, My goal here wasn't to define an OPP for the CPU since it is the camera interface node but to avoid let the CPU go to down. I haven't found how to use OPP bindings, can you provide me hints or examples of how I should do it? Thanks, Benjamin > > Rob
diff --git a/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml b/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml index 3fe778cb5cc3..05ca85a2411a 100644 --- a/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml +++ b/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml @@ -44,6 +44,13 @@ properties: bindings defined in Documentation/devicetree/bindings/media/video-interfaces.txt. + st,stm32-dcmi-min-frequency: + description: DCMI minimum CPUs frequency requirement (in KHz). + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - minimum: 0 + - default: 0 + required: - compatible - reg @@ -71,6 +78,7 @@ examples: clock-names = "mclk"; dmas = <&dmamux1 75 0x400 0x0d>; dma-names = "tx"; + st,stm32-dcmi-min-frequency = <650000>; port { dcmi_0: endpoint {
Document st,stm32-dcmi-min-frequency property which is used to request CPUs minimum frequency when streaming frames. Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com> --- Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml | 8 ++++++++ 1 file changed, 8 insertions(+)