| Message ID | 20201008170426.465-2-lukasz.luba@arm.com (mailing list archive) |
|---|---|
| State | Superseded, archived |
| Headers | show |
| Series | Improve the estimations in Intelligent Power Allocation | expand |
On Thursday 08 Oct 2020 at 18:04:25 (+0100), Lukasz Luba wrote: > Intelligent Power Allocation (IPA) is built around the PID controller > concept. The initialization code tries to setup the environment based on > the information available in DT or estimate the value based on minimum > power reported by each of the cooling device. The estimation will have an > impact on the PID controller behaviour via the related 'k_po', 'k_pu', > 'k_i' coefficients and also on the power budget calculation. > > This change prevents the situation when 'k_i' is relatively big compared > to 'k_po' and 'k_pu' values. This might happen when the estimation for > 'sustainable_power' returned small value, thus 'k_po' and 'k_pu' are > small. > > Signed-off-by: Lukasz Luba <lukasz.luba@arm.com> > --- > drivers/thermal/gov_power_allocator.c | 8 ++++++-- > 1 file changed, 6 insertions(+), 2 deletions(-) > > diff --git a/drivers/thermal/gov_power_allocator.c b/drivers/thermal/gov_power_allocator.c > index e566806f1550..aa35aa6c561c 100644 > --- a/drivers/thermal/gov_power_allocator.c > +++ b/drivers/thermal/gov_power_allocator.c > @@ -132,6 +132,7 @@ static void estimate_pid_constants(struct thermal_zone_device *tz, > int ret; > int switch_on_temp; > u32 temperature_threshold; > + s32 k_i; > > ret = tz->ops->get_trip_temp(tz, trip_switch_on, &switch_on_temp); > if (ret) > @@ -157,8 +158,11 @@ static void estimate_pid_constants(struct thermal_zone_device *tz, > tz->tzp->k_pu = int_to_frac(2 * sustainable_power) / > temperature_threshold; > > - if (!tz->tzp->k_i || force) > - tz->tzp->k_i = int_to_frac(10) / 1000; > + if (!tz->tzp->k_i || force) { > + k_i = tz->tzp->k_pu / 10; > + tz->tzp->k_i = k_i > 0 ? k_i : 1; > + } I spent some time to understand how smaller or bigger values here impact the stability of the output and its closeness to the control temperature so I could give you and informed review :). I did observed that if the k_i value has the same order of magnitude as k_p, the output oscillates more, so I do believe this is a good change to have. What I also observed is that a small k_d value could be very beneficial in quicker stabilising the oscillation and saw that it's recommended to have for temperature, or in general for systems with measurement lag. It's probably worth experimenting with some real systems first, but I wonder if setting k_d to 1 as well is a good default. The risk is that we will end up too conservative and not take advantage of some power budget that's actually still left on the table. In any case, this is a story for another time :). For these changes: Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com> Regards, Ionela. > + > /* > * The default for k_d and integral_cutoff is 0, so we can > * leave them as they are. > -- > 2.17.1 >
On 10/9/20 2:05 PM, Ionela Voinescu wrote: > On Thursday 08 Oct 2020 at 18:04:25 (+0100), Lukasz Luba wrote: >> Intelligent Power Allocation (IPA) is built around the PID controller >> concept. The initialization code tries to setup the environment based on >> the information available in DT or estimate the value based on minimum >> power reported by each of the cooling device. The estimation will have an >> impact on the PID controller behaviour via the related 'k_po', 'k_pu', >> 'k_i' coefficients and also on the power budget calculation. >> >> This change prevents the situation when 'k_i' is relatively big compared >> to 'k_po' and 'k_pu' values. This might happen when the estimation for >> 'sustainable_power' returned small value, thus 'k_po' and 'k_pu' are >> small. >> >> Signed-off-by: Lukasz Luba <lukasz.luba@arm.com> >> --- >> drivers/thermal/gov_power_allocator.c | 8 ++++++-- >> 1 file changed, 6 insertions(+), 2 deletions(-) >> >> diff --git a/drivers/thermal/gov_power_allocator.c b/drivers/thermal/gov_power_allocator.c >> index e566806f1550..aa35aa6c561c 100644 >> --- a/drivers/thermal/gov_power_allocator.c >> +++ b/drivers/thermal/gov_power_allocator.c >> @@ -132,6 +132,7 @@ static void estimate_pid_constants(struct thermal_zone_device *tz, >> int ret; >> int switch_on_temp; >> u32 temperature_threshold; >> + s32 k_i; >> >> ret = tz->ops->get_trip_temp(tz, trip_switch_on, &switch_on_temp); >> if (ret) >> @@ -157,8 +158,11 @@ static void estimate_pid_constants(struct thermal_zone_device *tz, >> tz->tzp->k_pu = int_to_frac(2 * sustainable_power) / >> temperature_threshold; >> >> - if (!tz->tzp->k_i || force) >> - tz->tzp->k_i = int_to_frac(10) / 1000; >> + if (!tz->tzp->k_i || force) { >> + k_i = tz->tzp->k_pu / 10; >> + tz->tzp->k_i = k_i > 0 ? k_i : 1; >> + } > > I spent some time to understand how smaller or bigger values here impact > the stability of the output and its closeness to the control temperature > so I could give you and informed review :). > > I did observed that if the k_i value has the same order of magnitude as > k_p, the output oscillates more, so I do believe this is a good change > to have. > > What I also observed is that a small k_d value could be very beneficial > in quicker stabilising the oscillation and saw that it's recommended to > have for temperature, or in general for systems with measurement lag. > > It's probably worth experimenting with some real systems first, but I > wonder if setting k_d to 1 as well is a good default. The risk is that > we will end up too conservative and not take advantage of some power > budget that's actually still left on the table. In any case, this is a > story for another time :). > > For these changes: > > Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com> Thank you for the review. I will add it to the v3, which I am going to send soon. Regards, Lukasz > > Regards, > Ionela. > >> + >> /* >> * The default for k_d and integral_cutoff is 0, so we can >> * leave them as they are. >> -- >> 2.17.1 >> > > >
diff --git a/drivers/thermal/gov_power_allocator.c b/drivers/thermal/gov_power_allocator.c index e566806f1550..aa35aa6c561c 100644 --- a/drivers/thermal/gov_power_allocator.c +++ b/drivers/thermal/gov_power_allocator.c @@ -132,6 +132,7 @@ static void estimate_pid_constants(struct thermal_zone_device *tz, int ret; int switch_on_temp; u32 temperature_threshold; + s32 k_i; ret = tz->ops->get_trip_temp(tz, trip_switch_on, &switch_on_temp); if (ret) @@ -157,8 +158,11 @@ static void estimate_pid_constants(struct thermal_zone_device *tz, tz->tzp->k_pu = int_to_frac(2 * sustainable_power) / temperature_threshold; - if (!tz->tzp->k_i || force) - tz->tzp->k_i = int_to_frac(10) / 1000; + if (!tz->tzp->k_i || force) { + k_i = tz->tzp->k_pu / 10; + tz->tzp->k_i = k_i > 0 ? k_i : 1; + } + /* * The default for k_d and integral_cutoff is 0, so we can * leave them as they are.
Intelligent Power Allocation (IPA) is built around the PID controller concept. The initialization code tries to setup the environment based on the information available in DT or estimate the value based on minimum power reported by each of the cooling device. The estimation will have an impact on the PID controller behaviour via the related 'k_po', 'k_pu', 'k_i' coefficients and also on the power budget calculation. This change prevents the situation when 'k_i' is relatively big compared to 'k_po' and 'k_pu' values. This might happen when the estimation for 'sustainable_power' returned small value, thus 'k_po' and 'k_pu' are small. Signed-off-by: Lukasz Luba <lukasz.luba@arm.com> --- drivers/thermal/gov_power_allocator.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-)