| Message ID | 1603442745-13085-5-git-send-email-yilun.xu@intel.com (mailing list archive) |
|---|---|
| State | New |
| Headers | show |
| Series | Add the netdev support for Intel PAC N3000 FPGA | expand |
On 10/23/20 1:45 AM, Xu Yilun wrote: > This driver supports the ethernet retimers (Parkvale) for the Intel PAC > (Programmable Acceleration Card) N3000, which is a FPGA based Smart NIC. Parkvale is a code name, it would be better if the public name was used. As this is a physical chip that could be used on other cards, I think the generic parts should be split out of intel-m10-bmc-retimer.c into a separate file, maybe retimer-c827.c Tom > > Parkvale is an Intel(R) Ethernet serdes transceiver chip that supports up > to 100G transfer. On Intel PAC N3000 there are 2 Parkvale chips managed > by the Intel MAX 10 BMC firmware. They are configured in 4 ports 10G/25G > retimer mode. Host could query their link status via retimer interfaces > (Shared registers) on Intel MAX 10 BMC. > > The driver adds the phy device for each port of the 2 retimer chips. > Since the phys are not accessed by the real MDIO bus, it creates a virtual > mdio bus for each NIC device instance, and a dedicated phy driver which > only provides the supported features and link state. > > A DFL Ether Group driver will create net devices and connect to these > phys. > > Signed-off-by: Xu Yilun <yilun.xu@intel.com> > --- > drivers/fpga/dfl-n3000-nios.c | 11 +- > drivers/mfd/intel-m10-bmc.c | 18 ++ > drivers/net/ethernet/intel/Kconfig | 12 ++ > drivers/net/ethernet/intel/Makefile | 2 + > drivers/net/ethernet/intel/intel-m10-bmc-retimer.c | 229 +++++++++++++++++++++ > include/linux/mfd/intel-m10-bmc.h | 16 ++ > 6 files changed, 286 insertions(+), 2 deletions(-) > create mode 100644 drivers/net/ethernet/intel/intel-m10-bmc-retimer.c > > diff --git a/drivers/fpga/dfl-n3000-nios.c b/drivers/fpga/dfl-n3000-nios.c > index 4983a2b..096931a 100644 > --- a/drivers/fpga/dfl-n3000-nios.c > +++ b/drivers/fpga/dfl-n3000-nios.c > @@ -16,6 +16,7 @@ > #include <linux/io-64-nonatomic-lo-hi.h> > #include <linux/kernel.h> > #include <linux/module.h> > +#include <linux/mfd/intel-m10-bmc.h> > #include <linux/platform_device.h> > #include <linux/regmap.h> > #include <linux/stddef.h> > @@ -159,6 +160,8 @@ struct n3000_nios { > struct regmap *regmap; > struct device *dev; > struct platform_device *altera_spi; > + struct intel_m10bmc_platdata m10bmc_pdata; > + struct intel_m10bmc_retimer_pdata m10bmc_retimer_pdata; > }; > > static ssize_t nios_fw_version_show(struct device *dev, > @@ -412,7 +415,8 @@ static struct spi_board_info m10_n3000_info = { > .chip_select = 0, > }; > > -static int create_altera_spi_controller(struct n3000_nios *nn) > +static int create_altera_spi_controller(struct n3000_nios *nn, > + struct device *retimer_master) > { > struct altera_spi_platform_data pdata = { 0 }; > struct platform_device_info pdevinfo = { 0 }; > @@ -431,6 +435,9 @@ static int create_altera_spi_controller(struct n3000_nios *nn) > pdata.bits_per_word_mask = > SPI_BPW_RANGE_MASK(1, FIELD_GET(N3000_NS_PARAM_DATA_WIDTH, v)); > > + nn->m10bmc_retimer_pdata.retimer_master = retimer_master; > + nn->m10bmc_pdata.retimer = &nn->m10bmc_retimer_pdata; > + m10_n3000_info.platform_data = &nn->m10bmc_pdata; > pdata.num_devices = 1; > pdata.devices = &m10_n3000_info; > > @@ -549,7 +556,7 @@ static int n3000_nios_probe(struct dfl_device *ddev) > if (ret) > return ret; > > - ret = create_altera_spi_controller(nn); > + ret = create_altera_spi_controller(nn, dfl_dev_get_base_dev(ddev)); > if (ret) > dev_err(dev, "altera spi controller create failed: %d\n", ret); > > diff --git a/drivers/mfd/intel-m10-bmc.c b/drivers/mfd/intel-m10-bmc.c > index b84579b..adbfb177 100644 > --- a/drivers/mfd/intel-m10-bmc.c > +++ b/drivers/mfd/intel-m10-bmc.c > @@ -23,6 +23,21 @@ static struct mfd_cell m10bmc_pacn3000_subdevs[] = { > { .name = "n3000bmc-secure" }, > }; > > +static void > +m10bmc_init_cells_platdata(struct intel_m10bmc_platdata *pdata, > + struct mfd_cell *cells, int n_cell) > +{ > + int i; > + > + for (i = 0; i < n_cell; i++) { > + if (!strcmp(cells[i].name, "n3000bmc-retimer")) { > + cells[i].platform_data = pdata->retimer; > + cells[i].pdata_size = > + pdata->retimer ? sizeof(*pdata->retimer) : 0; > + } > + } > +} > + > static struct regmap_config intel_m10bmc_regmap_config = { > .reg_bits = 32, > .val_bits = 32, > @@ -97,6 +112,7 @@ static int check_m10bmc_version(struct intel_m10bmc *ddata) > > static int intel_m10_bmc_spi_probe(struct spi_device *spi) > { > + struct intel_m10bmc_platdata *pdata = dev_get_platdata(&spi->dev); > const struct spi_device_id *id = spi_get_device_id(spi); > struct device *dev = &spi->dev; > struct mfd_cell *cells; > @@ -134,6 +150,8 @@ static int intel_m10_bmc_spi_probe(struct spi_device *spi) > return -ENODEV; > } > > + m10bmc_init_cells_platdata(pdata, cells, n_cell); > + > ret = devm_mfd_add_devices(dev, PLATFORM_DEVID_AUTO, cells, n_cell, > NULL, 0, NULL); > if (ret) > diff --git a/drivers/net/ethernet/intel/Kconfig b/drivers/net/ethernet/intel/Kconfig > index 5aa8631..81c43d4 100644 > --- a/drivers/net/ethernet/intel/Kconfig > +++ b/drivers/net/ethernet/intel/Kconfig > @@ -343,4 +343,16 @@ config IGC > To compile this driver as a module, choose M here. The module > will be called igc. > > +config INTEL_M10_BMC_RETIMER > + tristate "Intel(R) MAX 10 BMC ethernet retimer support" > + depends on MFD_INTEL_M10_BMC > + select PHYLIB > + help > + This driver supports the ethernet retimer (Parkvale) on > + Intel(R) MAX 10 BMC, which is used by Intel PAC N3000 FPGA based > + Smart NIC. > + > + To compile this driver as a module, choose M here. The module > + will be called intel-m10-bmc-retimer. > + > endif # NET_VENDOR_INTEL > diff --git a/drivers/net/ethernet/intel/Makefile b/drivers/net/ethernet/intel/Makefile > index 3075290..5965447 100644 > --- a/drivers/net/ethernet/intel/Makefile > +++ b/drivers/net/ethernet/intel/Makefile > @@ -16,3 +16,5 @@ obj-$(CONFIG_IXGB) += ixgb/ > obj-$(CONFIG_IAVF) += iavf/ > obj-$(CONFIG_FM10K) += fm10k/ > obj-$(CONFIG_ICE) += ice/ > + > +obj-$(CONFIG_INTEL_M10_BMC_RETIMER) += intel-m10-bmc-retimer.o > diff --git a/drivers/net/ethernet/intel/intel-m10-bmc-retimer.c b/drivers/net/ethernet/intel/intel-m10-bmc-retimer.c > new file mode 100644 > index 0000000..c7b0558 > --- /dev/null > +++ b/drivers/net/ethernet/intel/intel-m10-bmc-retimer.c > @@ -0,0 +1,229 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* Intel Max10 BMC Retimer Interface Driver > + * > + * Copyright (C) 2018-2020 Intel Corporation. All rights reserved. > + * > + */ > +#include <linux/device.h> > +#include <linux/mfd/intel-m10-bmc.h> > +#include <linux/module.h> > +#include <linux/phy.h> > +#include <linux/platform_device.h> > + > +#define NUM_CHIP 2 > +#define MAX_LINK 4 > + > +#define BITS_MASK(nbits) ((1 << (nbits)) - 1) > + > +#define N3000BMC_RETIMER_DEV_NAME "n3000bmc-retimer" > +#define M10BMC_RETIMER_MII_NAME "m10bmc retimer mii" > + > +struct m10bmc_retimer { > + struct device *dev; > + struct intel_m10bmc *m10bmc; > + int num_devs; > + struct device *base_dev; > + struct mii_bus *retimer_mii_bus; > +}; > + > +#define RETIMER_LINK_STAT_BIT(retimer_id, link_id) \ > + BIT(((retimer_id) << 2) + (link_id)) > + > +static u32 retimer_get_link(struct m10bmc_retimer *retimer, int index) > +{ > + unsigned int val; > + > + if (m10bmc_sys_read(retimer->m10bmc, PKVL_LINK_STATUS, &val)) { > + dev_err(retimer->dev, "fail to read PKVL_LINK_STATUS\n"); > + return 0; > + } > + > + if (val & BIT(index)) > + return 1; > + > + return 0; > +} > + > +static int m10bmc_retimer_phy_match(struct phy_device *phydev) > +{ > + if (phydev->mdio.bus->name && > + !strcmp(phydev->mdio.bus->name, M10BMC_RETIMER_MII_NAME)) { > + return 1; > + } > + > + return 0; > +} > + > +static int m10bmc_retimer_phy_probe(struct phy_device *phydev) > +{ > + struct m10bmc_retimer *retimer = phydev->mdio.bus->priv; > + > + phydev->priv = retimer; > + > + return 0; > +} > + > +static void m10bmc_retimer_phy_remove(struct phy_device *phydev) > +{ > + if (phydev->attached_dev) > + phy_disconnect(phydev); > +} > + > +static int m10bmc_retimer_read_status(struct phy_device *phydev) > +{ > + struct m10bmc_retimer *retimer = phydev->priv; > + > + phydev->link = retimer_get_link(retimer, phydev->mdio.addr); > + > + phydev->duplex = DUPLEX_FULL; > + > + return 0; > +} > + > +static int m10bmc_retimer_get_features(struct phy_device *phydev) > +{ > + linkmode_set_bit(ETHTOOL_LINK_MODE_10000baseT_Full_BIT, > + phydev->supported); > + linkmode_set_bit(ETHTOOL_LINK_MODE_10000baseSR_Full_BIT, > + phydev->supported); > + linkmode_set_bit(ETHTOOL_LINK_MODE_10000baseLR_Full_BIT, > + phydev->supported); > + > + linkmode_set_bit(ETHTOOL_LINK_MODE_25000baseCR_Full_BIT, > + phydev->supported); > + linkmode_set_bit(ETHTOOL_LINK_MODE_25000baseSR_Full_BIT, > + phydev->supported); > + > + linkmode_set_bit(ETHTOOL_LINK_MODE_40000baseCR4_Full_BIT, > + phydev->supported); > + linkmode_set_bit(ETHTOOL_LINK_MODE_40000baseSR4_Full_BIT, > + phydev->supported); > + linkmode_set_bit(ETHTOOL_LINK_MODE_40000baseLR4_Full_BIT, > + phydev->supported); > + > + linkmode_set_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT, phydev->supported); > + > + return 0; > +} > + > +static struct phy_driver m10bmc_retimer_phy_driver = { > + .phy_id = 0xffffffff, > + .phy_id_mask = 0xffffffff, > + .name = "m10bmc retimer PHY", > + .match_phy_device = m10bmc_retimer_phy_match, > + .probe = m10bmc_retimer_phy_probe, > + .remove = m10bmc_retimer_phy_remove, > + .read_status = m10bmc_retimer_read_status, > + .get_features = m10bmc_retimer_get_features, > + .read_mmd = genphy_read_mmd_unsupported, > + .write_mmd = genphy_write_mmd_unsupported, > +}; > + > +static int m10bmc_retimer_read(struct mii_bus *bus, int addr, int regnum) > +{ > + struct m10bmc_retimer *retimer = bus->priv; > + > + if (addr < retimer->num_devs && > + (regnum == MII_PHYSID1 || regnum == MII_PHYSID2)) > + return 0; > + > + return 0xffff; > +} > + > +static int m10bmc_retimer_write(struct mii_bus *bus, int addr, int regnum, u16 val) > +{ > + return 0; > +} > + > +static int m10bmc_retimer_mii_bus_init(struct m10bmc_retimer *retimer) > +{ > + struct mii_bus *bus; > + int ret; > + > + bus = devm_mdiobus_alloc(retimer->dev); > + if (!bus) > + return -ENOMEM; > + > + bus->priv = (void *)retimer; > + bus->name = M10BMC_RETIMER_MII_NAME; > + bus->read = m10bmc_retimer_read; > + bus->write = m10bmc_retimer_write; > + snprintf(bus->id, MII_BUS_ID_SIZE, "%s-mii", > + dev_name(retimer->base_dev)); > + bus->parent = retimer->dev; > + bus->phy_mask = ~(BITS_MASK(retimer->num_devs)); > + > + ret = mdiobus_register(bus); > + if (ret) > + return ret; > + > + retimer->retimer_mii_bus = bus; > + > + return 0; > +} > + > +static void m10bmc_retimer_mii_bus_uinit(struct m10bmc_retimer *retimer) > +{ > + mdiobus_unregister(retimer->retimer_mii_bus); > +} > + > +static int intel_m10bmc_retimer_probe(struct platform_device *pdev) > +{ > + struct intel_m10bmc_retimer_pdata *pdata = dev_get_platdata(&pdev->dev); > + struct intel_m10bmc *m10bmc = dev_get_drvdata(pdev->dev.parent); > + struct m10bmc_retimer *retimer; > + > + retimer = devm_kzalloc(&pdev->dev, sizeof(*retimer), GFP_KERNEL); > + if (!retimer) > + return -ENOMEM; > + > + dev_set_drvdata(&pdev->dev, retimer); > + > + retimer->dev = &pdev->dev; > + retimer->m10bmc = m10bmc; > + retimer->base_dev = pdata->retimer_master; > + retimer->num_devs = NUM_CHIP * MAX_LINK; > + > + return m10bmc_retimer_mii_bus_init(retimer); > +} > + > +static int intel_m10bmc_retimer_remove(struct platform_device *pdev) > +{ > + struct m10bmc_retimer *retimer = dev_get_drvdata(&pdev->dev); > + > + m10bmc_retimer_mii_bus_uinit(retimer); > + > + return 0; > +} > + > +static struct platform_driver intel_m10bmc_retimer_driver = { > + .probe = intel_m10bmc_retimer_probe, > + .remove = intel_m10bmc_retimer_remove, > + .driver = { > + .name = N3000BMC_RETIMER_DEV_NAME, > + }, > +}; > + > +static int __init intel_m10bmc_retimer_init(void) > +{ > + int ret; > + > + ret = phy_driver_register(&m10bmc_retimer_phy_driver, THIS_MODULE); > + if (ret) > + return ret; > + > + return platform_driver_register(&intel_m10bmc_retimer_driver); > +} > +module_init(intel_m10bmc_retimer_init); > + > +static void __exit intel_m10bmc_retimer_exit(void) > +{ > + platform_driver_unregister(&intel_m10bmc_retimer_driver); > + phy_driver_unregister(&m10bmc_retimer_phy_driver); > +} > +module_exit(intel_m10bmc_retimer_exit); > + > +MODULE_ALIAS("platform:" N3000BMC_RETIMER_DEV_NAME); > +MODULE_AUTHOR("Intel Corporation"); > +MODULE_DESCRIPTION("Intel MAX 10 BMC retimer driver"); > +MODULE_LICENSE("GPL"); > diff --git a/include/linux/mfd/intel-m10-bmc.h b/include/linux/mfd/intel-m10-bmc.h > index c8ef2f1..3d9d22c 100644 > --- a/include/linux/mfd/intel-m10-bmc.h > +++ b/include/linux/mfd/intel-m10-bmc.h > @@ -21,6 +21,22 @@ > #define M10BMC_VER_PCB_INFO_MSK GENMASK(31, 24) > #define M10BMC_VER_LEGACY_INVALID 0xffffffff > > +/* PKVL related registers, in system register region */ > +#define PKVL_LINK_STATUS 0x164 > + > +/** > + * struct intel_m10bmc_retimer_pdata - subdev retimer platform data > + * > + * @retimer_master: the NIC device which connects to the retimers on m10bmc > + */ > +struct intel_m10bmc_retimer_pdata { > + struct device *retimer_master; > +}; > + > +struct intel_m10bmc_platdata { > + struct intel_m10bmc_retimer_pdata *retimer; > +}; > + > /** > * struct intel_m10bmc - Intel MAX 10 BMC parent driver data structure > * @dev: this device
On Sat, Oct 24, 2020 at 08:03:51AM -0700, Tom Rix wrote: > > On 10/23/20 1:45 AM, Xu Yilun wrote: > > This driver supports the ethernet retimers (Parkvale) for the Intel PAC > > (Programmable Acceleration Card) N3000, which is a FPGA based Smart NIC. > > Parkvale is a code name, it would be better if the public name was used. > > As this is a physical chip that could be used on other cards, > > I think the generic parts should be split out of intel-m10-bmc-retimer.c > > into a separate file, maybe retimer-c827.c This driver is not really a driver for the Parkvale. That driver is hidden away in the BMC. So we need to be a bit careful with the name, leaving it available for when somebody writes a real Linux driver for retimer. Andrew
On 10/24/20 9:39 AM, Andrew Lunn wrote: > On Sat, Oct 24, 2020 at 08:03:51AM -0700, Tom Rix wrote: >> On 10/23/20 1:45 AM, Xu Yilun wrote: >>> This driver supports the ethernet retimers (Parkvale) for the Intel PAC >>> (Programmable Acceleration Card) N3000, which is a FPGA based Smart NIC. >> Parkvale is a code name, it would be better if the public name was used. >> >> As this is a physical chip that could be used on other cards, >> >> I think the generic parts should be split out of intel-m10-bmc-retimer.c >> >> into a separate file, maybe retimer-c827.c > This driver is not really a driver for the Parkvale. That driver is > hidden away in the BMC. So we need to be a bit careful with the name, > leaving it available for when somebody writes a real Linux driver for > retimer. Then the parkvale verbage should be removed. And the doc ascii diagram be updated with a +---------+ | BMC | | retimer | +---------+ Tom > Andrew >
On Sat, Oct 24, 2020 at 10:36:36AM -0700, Tom Rix wrote: > > On 10/24/20 9:39 AM, Andrew Lunn wrote: > > On Sat, Oct 24, 2020 at 08:03:51AM -0700, Tom Rix wrote: > >> On 10/23/20 1:45 AM, Xu Yilun wrote: > >>> This driver supports the ethernet retimers (Parkvale) for the Intel PAC > >>> (Programmable Acceleration Card) N3000, which is a FPGA based Smart NIC. > >> Parkvale is a code name, it would be better if the public name was used. > >> > >> As this is a physical chip that could be used on other cards, > >> > >> I think the generic parts should be split out of intel-m10-bmc-retimer.c > >> > >> into a separate file, maybe retimer-c827.c > > This driver is not really a driver for the Parkvale. That driver is > > hidden away in the BMC. So we need to be a bit careful with the name, > > leaving it available for when somebody writes a real Linux driver for > > retimer. > > Then the parkvale verbage should be removed. > > And the doc ascii diagram be updated with a > > +---------+ > > | BMC | > > | retimer | > > +---------+ Yes, i would like to get a better understanding of what the BMC is actually doing, particularly the SFP. Given my current limited understanding of the driver architecture, i'm not sure it is flexiable enough to handle other cards where Linux is controlling the SFPs, the retimer, the host side PCS of the Arria 10, etc. Once Linux is driving all that, you need phylink, not phylib. The proposed phylib driver/mdio bus driver actually looks like a hack. Andrew
diff --git a/drivers/fpga/dfl-n3000-nios.c b/drivers/fpga/dfl-n3000-nios.c index 4983a2b..096931a 100644 --- a/drivers/fpga/dfl-n3000-nios.c +++ b/drivers/fpga/dfl-n3000-nios.c @@ -16,6 +16,7 @@ #include <linux/io-64-nonatomic-lo-hi.h> #include <linux/kernel.h> #include <linux/module.h> +#include <linux/mfd/intel-m10-bmc.h> #include <linux/platform_device.h> #include <linux/regmap.h> #include <linux/stddef.h> @@ -159,6 +160,8 @@ struct n3000_nios { struct regmap *regmap; struct device *dev; struct platform_device *altera_spi; + struct intel_m10bmc_platdata m10bmc_pdata; + struct intel_m10bmc_retimer_pdata m10bmc_retimer_pdata; }; static ssize_t nios_fw_version_show(struct device *dev, @@ -412,7 +415,8 @@ static struct spi_board_info m10_n3000_info = { .chip_select = 0, }; -static int create_altera_spi_controller(struct n3000_nios *nn) +static int create_altera_spi_controller(struct n3000_nios *nn, + struct device *retimer_master) { struct altera_spi_platform_data pdata = { 0 }; struct platform_device_info pdevinfo = { 0 }; @@ -431,6 +435,9 @@ static int create_altera_spi_controller(struct n3000_nios *nn) pdata.bits_per_word_mask = SPI_BPW_RANGE_MASK(1, FIELD_GET(N3000_NS_PARAM_DATA_WIDTH, v)); + nn->m10bmc_retimer_pdata.retimer_master = retimer_master; + nn->m10bmc_pdata.retimer = &nn->m10bmc_retimer_pdata; + m10_n3000_info.platform_data = &nn->m10bmc_pdata; pdata.num_devices = 1; pdata.devices = &m10_n3000_info; @@ -549,7 +556,7 @@ static int n3000_nios_probe(struct dfl_device *ddev) if (ret) return ret; - ret = create_altera_spi_controller(nn); + ret = create_altera_spi_controller(nn, dfl_dev_get_base_dev(ddev)); if (ret) dev_err(dev, "altera spi controller create failed: %d\n", ret); diff --git a/drivers/mfd/intel-m10-bmc.c b/drivers/mfd/intel-m10-bmc.c index b84579b..adbfb177 100644 --- a/drivers/mfd/intel-m10-bmc.c +++ b/drivers/mfd/intel-m10-bmc.c @@ -23,6 +23,21 @@ static struct mfd_cell m10bmc_pacn3000_subdevs[] = { { .name = "n3000bmc-secure" }, }; +static void +m10bmc_init_cells_platdata(struct intel_m10bmc_platdata *pdata, + struct mfd_cell *cells, int n_cell) +{ + int i; + + for (i = 0; i < n_cell; i++) { + if (!strcmp(cells[i].name, "n3000bmc-retimer")) { + cells[i].platform_data = pdata->retimer; + cells[i].pdata_size = + pdata->retimer ? sizeof(*pdata->retimer) : 0; + } + } +} + static struct regmap_config intel_m10bmc_regmap_config = { .reg_bits = 32, .val_bits = 32, @@ -97,6 +112,7 @@ static int check_m10bmc_version(struct intel_m10bmc *ddata) static int intel_m10_bmc_spi_probe(struct spi_device *spi) { + struct intel_m10bmc_platdata *pdata = dev_get_platdata(&spi->dev); const struct spi_device_id *id = spi_get_device_id(spi); struct device *dev = &spi->dev; struct mfd_cell *cells; @@ -134,6 +150,8 @@ static int intel_m10_bmc_spi_probe(struct spi_device *spi) return -ENODEV; } + m10bmc_init_cells_platdata(pdata, cells, n_cell); + ret = devm_mfd_add_devices(dev, PLATFORM_DEVID_AUTO, cells, n_cell, NULL, 0, NULL); if (ret) diff --git a/drivers/net/ethernet/intel/Kconfig b/drivers/net/ethernet/intel/Kconfig index 5aa8631..81c43d4 100644 --- a/drivers/net/ethernet/intel/Kconfig +++ b/drivers/net/ethernet/intel/Kconfig @@ -343,4 +343,16 @@ config IGC To compile this driver as a module, choose M here. The module will be called igc. +config INTEL_M10_BMC_RETIMER + tristate "Intel(R) MAX 10 BMC ethernet retimer support" + depends on MFD_INTEL_M10_BMC + select PHYLIB + help + This driver supports the ethernet retimer (Parkvale) on + Intel(R) MAX 10 BMC, which is used by Intel PAC N3000 FPGA based + Smart NIC. + + To compile this driver as a module, choose M here. The module + will be called intel-m10-bmc-retimer. + endif # NET_VENDOR_INTEL diff --git a/drivers/net/ethernet/intel/Makefile b/drivers/net/ethernet/intel/Makefile index 3075290..5965447 100644 --- a/drivers/net/ethernet/intel/Makefile +++ b/drivers/net/ethernet/intel/Makefile @@ -16,3 +16,5 @@ obj-$(CONFIG_IXGB) += ixgb/ obj-$(CONFIG_IAVF) += iavf/ obj-$(CONFIG_FM10K) += fm10k/ obj-$(CONFIG_ICE) += ice/ + +obj-$(CONFIG_INTEL_M10_BMC_RETIMER) += intel-m10-bmc-retimer.o diff --git a/drivers/net/ethernet/intel/intel-m10-bmc-retimer.c b/drivers/net/ethernet/intel/intel-m10-bmc-retimer.c new file mode 100644 index 0000000..c7b0558 --- /dev/null +++ b/drivers/net/ethernet/intel/intel-m10-bmc-retimer.c @@ -0,0 +1,229 @@ +// SPDX-License-Identifier: GPL-2.0 +/* Intel Max10 BMC Retimer Interface Driver + * + * Copyright (C) 2018-2020 Intel Corporation. All rights reserved. + * + */ +#include <linux/device.h> +#include <linux/mfd/intel-m10-bmc.h> +#include <linux/module.h> +#include <linux/phy.h> +#include <linux/platform_device.h> + +#define NUM_CHIP 2 +#define MAX_LINK 4 + +#define BITS_MASK(nbits) ((1 << (nbits)) - 1) + +#define N3000BMC_RETIMER_DEV_NAME "n3000bmc-retimer" +#define M10BMC_RETIMER_MII_NAME "m10bmc retimer mii" + +struct m10bmc_retimer { + struct device *dev; + struct intel_m10bmc *m10bmc; + int num_devs; + struct device *base_dev; + struct mii_bus *retimer_mii_bus; +}; + +#define RETIMER_LINK_STAT_BIT(retimer_id, link_id) \ + BIT(((retimer_id) << 2) + (link_id)) + +static u32 retimer_get_link(struct m10bmc_retimer *retimer, int index) +{ + unsigned int val; + + if (m10bmc_sys_read(retimer->m10bmc, PKVL_LINK_STATUS, &val)) { + dev_err(retimer->dev, "fail to read PKVL_LINK_STATUS\n"); + return 0; + } + + if (val & BIT(index)) + return 1; + + return 0; +} + +static int m10bmc_retimer_phy_match(struct phy_device *phydev) +{ + if (phydev->mdio.bus->name && + !strcmp(phydev->mdio.bus->name, M10BMC_RETIMER_MII_NAME)) { + return 1; + } + + return 0; +} + +static int m10bmc_retimer_phy_probe(struct phy_device *phydev) +{ + struct m10bmc_retimer *retimer = phydev->mdio.bus->priv; + + phydev->priv = retimer; + + return 0; +} + +static void m10bmc_retimer_phy_remove(struct phy_device *phydev) +{ + if (phydev->attached_dev) + phy_disconnect(phydev); +} + +static int m10bmc_retimer_read_status(struct phy_device *phydev) +{ + struct m10bmc_retimer *retimer = phydev->priv; + + phydev->link = retimer_get_link(retimer, phydev->mdio.addr); + + phydev->duplex = DUPLEX_FULL; + + return 0; +} + +static int m10bmc_retimer_get_features(struct phy_device *phydev) +{ + linkmode_set_bit(ETHTOOL_LINK_MODE_10000baseT_Full_BIT, + phydev->supported); + linkmode_set_bit(ETHTOOL_LINK_MODE_10000baseSR_Full_BIT, + phydev->supported); + linkmode_set_bit(ETHTOOL_LINK_MODE_10000baseLR_Full_BIT, + phydev->supported); + + linkmode_set_bit(ETHTOOL_LINK_MODE_25000baseCR_Full_BIT, + phydev->supported); + linkmode_set_bit(ETHTOOL_LINK_MODE_25000baseSR_Full_BIT, + phydev->supported); + + linkmode_set_bit(ETHTOOL_LINK_MODE_40000baseCR4_Full_BIT, + phydev->supported); + linkmode_set_bit(ETHTOOL_LINK_MODE_40000baseSR4_Full_BIT, + phydev->supported); + linkmode_set_bit(ETHTOOL_LINK_MODE_40000baseLR4_Full_BIT, + phydev->supported); + + linkmode_set_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT, phydev->supported); + + return 0; +} + +static struct phy_driver m10bmc_retimer_phy_driver = { + .phy_id = 0xffffffff, + .phy_id_mask = 0xffffffff, + .name = "m10bmc retimer PHY", + .match_phy_device = m10bmc_retimer_phy_match, + .probe = m10bmc_retimer_phy_probe, + .remove = m10bmc_retimer_phy_remove, + .read_status = m10bmc_retimer_read_status, + .get_features = m10bmc_retimer_get_features, + .read_mmd = genphy_read_mmd_unsupported, + .write_mmd = genphy_write_mmd_unsupported, +}; + +static int m10bmc_retimer_read(struct mii_bus *bus, int addr, int regnum) +{ + struct m10bmc_retimer *retimer = bus->priv; + + if (addr < retimer->num_devs && + (regnum == MII_PHYSID1 || regnum == MII_PHYSID2)) + return 0; + + return 0xffff; +} + +static int m10bmc_retimer_write(struct mii_bus *bus, int addr, int regnum, u16 val) +{ + return 0; +} + +static int m10bmc_retimer_mii_bus_init(struct m10bmc_retimer *retimer) +{ + struct mii_bus *bus; + int ret; + + bus = devm_mdiobus_alloc(retimer->dev); + if (!bus) + return -ENOMEM; + + bus->priv = (void *)retimer; + bus->name = M10BMC_RETIMER_MII_NAME; + bus->read = m10bmc_retimer_read; + bus->write = m10bmc_retimer_write; + snprintf(bus->id, MII_BUS_ID_SIZE, "%s-mii", + dev_name(retimer->base_dev)); + bus->parent = retimer->dev; + bus->phy_mask = ~(BITS_MASK(retimer->num_devs)); + + ret = mdiobus_register(bus); + if (ret) + return ret; + + retimer->retimer_mii_bus = bus; + + return 0; +} + +static void m10bmc_retimer_mii_bus_uinit(struct m10bmc_retimer *retimer) +{ + mdiobus_unregister(retimer->retimer_mii_bus); +} + +static int intel_m10bmc_retimer_probe(struct platform_device *pdev) +{ + struct intel_m10bmc_retimer_pdata *pdata = dev_get_platdata(&pdev->dev); + struct intel_m10bmc *m10bmc = dev_get_drvdata(pdev->dev.parent); + struct m10bmc_retimer *retimer; + + retimer = devm_kzalloc(&pdev->dev, sizeof(*retimer), GFP_KERNEL); + if (!retimer) + return -ENOMEM; + + dev_set_drvdata(&pdev->dev, retimer); + + retimer->dev = &pdev->dev; + retimer->m10bmc = m10bmc; + retimer->base_dev = pdata->retimer_master; + retimer->num_devs = NUM_CHIP * MAX_LINK; + + return m10bmc_retimer_mii_bus_init(retimer); +} + +static int intel_m10bmc_retimer_remove(struct platform_device *pdev) +{ + struct m10bmc_retimer *retimer = dev_get_drvdata(&pdev->dev); + + m10bmc_retimer_mii_bus_uinit(retimer); + + return 0; +} + +static struct platform_driver intel_m10bmc_retimer_driver = { + .probe = intel_m10bmc_retimer_probe, + .remove = intel_m10bmc_retimer_remove, + .driver = { + .name = N3000BMC_RETIMER_DEV_NAME, + }, +}; + +static int __init intel_m10bmc_retimer_init(void) +{ + int ret; + + ret = phy_driver_register(&m10bmc_retimer_phy_driver, THIS_MODULE); + if (ret) + return ret; + + return platform_driver_register(&intel_m10bmc_retimer_driver); +} +module_init(intel_m10bmc_retimer_init); + +static void __exit intel_m10bmc_retimer_exit(void) +{ + platform_driver_unregister(&intel_m10bmc_retimer_driver); + phy_driver_unregister(&m10bmc_retimer_phy_driver); +} +module_exit(intel_m10bmc_retimer_exit); + +MODULE_ALIAS("platform:" N3000BMC_RETIMER_DEV_NAME); +MODULE_AUTHOR("Intel Corporation"); +MODULE_DESCRIPTION("Intel MAX 10 BMC retimer driver"); +MODULE_LICENSE("GPL"); diff --git a/include/linux/mfd/intel-m10-bmc.h b/include/linux/mfd/intel-m10-bmc.h index c8ef2f1..3d9d22c 100644 --- a/include/linux/mfd/intel-m10-bmc.h +++ b/include/linux/mfd/intel-m10-bmc.h @@ -21,6 +21,22 @@ #define M10BMC_VER_PCB_INFO_MSK GENMASK(31, 24) #define M10BMC_VER_LEGACY_INVALID 0xffffffff +/* PKVL related registers, in system register region */ +#define PKVL_LINK_STATUS 0x164 + +/** + * struct intel_m10bmc_retimer_pdata - subdev retimer platform data + * + * @retimer_master: the NIC device which connects to the retimers on m10bmc + */ +struct intel_m10bmc_retimer_pdata { + struct device *retimer_master; +}; + +struct intel_m10bmc_platdata { + struct intel_m10bmc_retimer_pdata *retimer; +}; + /** * struct intel_m10bmc - Intel MAX 10 BMC parent driver data structure * @dev: this device
This driver supports the ethernet retimers (Parkvale) for the Intel PAC (Programmable Acceleration Card) N3000, which is a FPGA based Smart NIC. Parkvale is an Intel(R) Ethernet serdes transceiver chip that supports up to 100G transfer. On Intel PAC N3000 there are 2 Parkvale chips managed by the Intel MAX 10 BMC firmware. They are configured in 4 ports 10G/25G retimer mode. Host could query their link status via retimer interfaces (Shared registers) on Intel MAX 10 BMC. The driver adds the phy device for each port of the 2 retimer chips. Since the phys are not accessed by the real MDIO bus, it creates a virtual mdio bus for each NIC device instance, and a dedicated phy driver which only provides the supported features and link state. A DFL Ether Group driver will create net devices and connect to these phys. Signed-off-by: Xu Yilun <yilun.xu@intel.com> --- drivers/fpga/dfl-n3000-nios.c | 11 +- drivers/mfd/intel-m10-bmc.c | 18 ++ drivers/net/ethernet/intel/Kconfig | 12 ++ drivers/net/ethernet/intel/Makefile | 2 + drivers/net/ethernet/intel/intel-m10-bmc-retimer.c | 229 +++++++++++++++++++++ include/linux/mfd/intel-m10-bmc.h | 16 ++ 6 files changed, 286 insertions(+), 2 deletions(-) create mode 100644 drivers/net/ethernet/intel/intel-m10-bmc-retimer.c