| Message ID | 20201029081513.10562-2-chuanjia.liu@mediatek.com (mailing list archive) |
|---|---|
| State | Changes Requested, archived |
| Headers | show |
| Series | PCI: mediatek: Spilt PCIe node to comply with hardware design | expand |
On Thu, 29 Oct 2020 16:15:10 +0800, Chuanjia Liu wrote: > Split the PCIe node and add pciecfg node to fix MSI issue. > > Signed-off-by: Chuanjia Liu <chuanjia.liu@mediatek.com> > Acked-by: Ryder Lee <ryder.lee@mediatek.com> > --- > .../bindings/pci/mediatek-pcie-cfg.yaml | 39 ++++++ > .../devicetree/bindings/pci/mediatek-pcie.txt | 129 +++++++++++------- > 2 files changed, 118 insertions(+), 50 deletions(-) > create mode 100644 Documentation/devicetree/bindings/pci/mediatek-pcie-cfg.yaml > My bot found errors running 'make dt_binding_check' on your patch: yamllint warnings/errors: ./Documentation/devicetree/bindings/pci/mediatek-pcie-cfg.yaml:19:7: [warning] wrong indentation: expected 4 but found 6 (indentation) dtschema/dtc warnings/errors: See https://patchwork.ozlabs.org/patch/1389940 The base for the patch is generally the last rc1. Any dependencies should be noted. If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date: pip3 install dtschema --upgrade Please check and re-submit.
On Thu, Oct 29, 2020 at 04:15:10PM +0800, Chuanjia Liu wrote: > Split the PCIe node and add pciecfg node to fix MSI issue. I still think if you are changing the binding this much, then further work should be done removing the slot nodes. > > Signed-off-by: Chuanjia Liu <chuanjia.liu@mediatek.com> > Acked-by: Ryder Lee <ryder.lee@mediatek.com> > --- > .../bindings/pci/mediatek-pcie-cfg.yaml | 39 ++++++ > .../devicetree/bindings/pci/mediatek-pcie.txt | 129 +++++++++++------- > 2 files changed, 118 insertions(+), 50 deletions(-) > create mode 100644 Documentation/devicetree/bindings/pci/mediatek-pcie-cfg.yaml > > diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie-cfg.yaml b/Documentation/devicetree/bindings/pci/mediatek-pcie-cfg.yaml > new file mode 100644 > index 000000000000..d3ecbcd032a2 > --- /dev/null > +++ b/Documentation/devicetree/bindings/pci/mediatek-pcie-cfg.yaml > @@ -0,0 +1,39 @@ > +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/pci/mediatek-pcie-cfg.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Mediatek PCIECFG controller > + > +maintainers: > + - Chuanjia Liu <chuanjia.liu@mediatek.com> > + - Jianjun Wang <jianjun.wang@mediatek.com> > + > +description: | > + The MediaTek PCIECFG controller controls some feature about > + LTSSM, ASPM and so on. > + > +properties: > + compatible: > + items: > + - enum: > + - mediatek,generic-pciecfg > + - const: syscon > + > + reg: > + maxItems: 1 > + > +required: > + - compatible > + - reg > + > +additionalProperties: false > + > +examples: > + - | > + pciecfg: pciecfg@1a140000 { > + compatible = "mediatek,generic-pciecfg", "syscon"; > + reg = <0x1a140000 0x1000>; > + }; > +... > diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt > index 7468d666763a..c14a2745de37 100644 > --- a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt > +++ b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt > @@ -8,7 +8,7 @@ Required properties: > "mediatek,mt7623-pcie" > "mediatek,mt7629-pcie" > - device_type: Must be "pci" > -- reg: Base addresses and lengths of the PCIe subsys and root ports. > +- reg: Base addresses and lengths of the root ports. > - reg-names: Names of the above areas to use during resource lookup. > - #address-cells: Address representation for root ports (must be 3) > - #size-cells: Size representation for root ports (must be 2) > @@ -143,56 +143,71 @@ Examples for MT7623: > > Examples for MT2712: > > - pcie: pcie@11700000 { > + pcie1: pcie@112ff000 { > compatible = "mediatek,mt2712-pcie"; > device_type = "pci"; > - reg = <0 0x11700000 0 0x1000>, > - <0 0x112ff000 0 0x1000>; > - reg-names = "port0", "port1"; > + reg = <0 0x112ff000 0 0x1000>; > + reg-names = "port1"; > #address-cells = <3>; > #size-cells = <2>; > - interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>, > - <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&topckgen CLK_TOP_PE2_MAC_P0_SEL>, > - <&topckgen CLK_TOP_PE2_MAC_P1_SEL>, > - <&pericfg CLK_PERI_PCIE0>, > + interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "pcie_irq"; > + clocks = <&topckgen CLK_TOP_PE2_MAC_P1_SEL>, > <&pericfg CLK_PERI_PCIE1>; > - clock-names = "sys_ck0", "sys_ck1", "ahb_ck0", "ahb_ck1"; > - phys = <&pcie0_phy PHY_TYPE_PCIE>, <&pcie1_phy PHY_TYPE_PCIE>; > - phy-names = "pcie-phy0", "pcie-phy1"; > + clock-names = "sys_ck1", "ahb_ck1"; > + phys = <&u3port1 PHY_TYPE_PCIE>; > + phy-names = "pcie-phy1"; > bus-range = <0x00 0xff>; > - ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>; > + ranges = <0x82000000 0 0x11400000 0x0 0x11400000 0 0x300000>; > > - pcie0: pcie@0,0 { > - reg = <0x0000 0 0 0 0>; > + slot1: pcie@1,0 { Does the driver still work if this is devfn 0 instead of 1 (or swap 0 and 1 slots)? I'll bet it does. The reason being is that AFAICT, the Mediatek PCI controller is Designware based. The registers at 0x70c and 0x73c are DWC 'port logic' registers. The DWC RC also has a quirk that it doesn't filter config accesses to only devfn 0 (see pci_dw_valid_device()), so your config accesses to the RP should work no matter what devfn you use. You'll have to get rid of the ports list and just get the mtk_pcie_port from bus->sysdata instead. Rob
Run "git log --oneline" and follow the convention, e.g., dt-bindings: PCI: mediatek: ... On Thu, Oct 29, 2020 at 04:15:10PM +0800, Chuanjia Liu wrote: > Split the PCIe node and add pciecfg node to fix MSI issue. I assume "split" refers to the new yaml file? It's not really obvious how the two files are connected. Could this be done in two patches? One for the split and one for the MSI issue? It'd be nice to say something more about the MSI issue. > Signed-off-by: Chuanjia Liu <chuanjia.liu@mediatek.com> > Acked-by: Ryder Lee <ryder.lee@mediatek.com> > --- > .../bindings/pci/mediatek-pcie-cfg.yaml | 39 ++++++ > .../devicetree/bindings/pci/mediatek-pcie.txt | 129 +++++++++++------- > 2 files changed, 118 insertions(+), 50 deletions(-) > create mode 100644 Documentation/devicetree/bindings/pci/mediatek-pcie-cfg.yaml > > diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie-cfg.yaml b/Documentation/devicetree/bindings/pci/mediatek-pcie-cfg.yaml > new file mode 100644 > index 000000000000..d3ecbcd032a2 > --- /dev/null > +++ b/Documentation/devicetree/bindings/pci/mediatek-pcie-cfg.yaml > @@ -0,0 +1,39 @@ > +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/pci/mediatek-pcie-cfg.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Mediatek PCIECFG controller > + > +maintainers: > + - Chuanjia Liu <chuanjia.liu@mediatek.com> > + - Jianjun Wang <jianjun.wang@mediatek.com> > + > +description: | > + The MediaTek PCIECFG controller controls some feature about > + LTSSM, ASPM and so on. > + > +properties: > + compatible: > + items: > + - enum: > + - mediatek,generic-pciecfg > + - const: syscon > + > + reg: > + maxItems: 1 > + > +required: > + - compatible > + - reg > + > +additionalProperties: false > + > +examples: > + - | > + pciecfg: pciecfg@1a140000 { > + compatible = "mediatek,generic-pciecfg", "syscon"; > + reg = <0x1a140000 0x1000>; > + }; > +... > diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt > index 7468d666763a..c14a2745de37 100644 > --- a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt > +++ b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt > @@ -8,7 +8,7 @@ Required properties: > "mediatek,mt7623-pcie" > "mediatek,mt7629-pcie" > - device_type: Must be "pci" > -- reg: Base addresses and lengths of the PCIe subsys and root ports. > +- reg: Base addresses and lengths of the root ports. > - reg-names: Names of the above areas to use during resource lookup. > - #address-cells: Address representation for root ports (must be 3) > - #size-cells: Size representation for root ports (must be 2) > @@ -143,56 +143,71 @@ Examples for MT7623: > > Examples for MT2712: > > - pcie: pcie@11700000 { > + pcie1: pcie@112ff000 { > compatible = "mediatek,mt2712-pcie"; > device_type = "pci"; > - reg = <0 0x11700000 0 0x1000>, > - <0 0x112ff000 0 0x1000>; > - reg-names = "port0", "port1"; > + reg = <0 0x112ff000 0 0x1000>; > + reg-names = "port1"; > #address-cells = <3>; > #size-cells = <2>; > - interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>, > - <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&topckgen CLK_TOP_PE2_MAC_P0_SEL>, > - <&topckgen CLK_TOP_PE2_MAC_P1_SEL>, > - <&pericfg CLK_PERI_PCIE0>, > + interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "pcie_irq"; > + clocks = <&topckgen CLK_TOP_PE2_MAC_P1_SEL>, > <&pericfg CLK_PERI_PCIE1>; > - clock-names = "sys_ck0", "sys_ck1", "ahb_ck0", "ahb_ck1"; > - phys = <&pcie0_phy PHY_TYPE_PCIE>, <&pcie1_phy PHY_TYPE_PCIE>; > - phy-names = "pcie-phy0", "pcie-phy1"; > + clock-names = "sys_ck1", "ahb_ck1"; > + phys = <&u3port1 PHY_TYPE_PCIE>; > + phy-names = "pcie-phy1"; > bus-range = <0x00 0xff>; > - ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>; > + ranges = <0x82000000 0 0x11400000 0x0 0x11400000 0 0x300000>; > > - pcie0: pcie@0,0 { > - reg = <0x0000 0 0 0 0>; > + slot1: pcie@1,0 { > + reg = <0x0800 0 0 0 0>; > #address-cells = <3>; > #size-cells = <2>; > #interrupt-cells = <1>; > ranges; > interrupt-map-mask = <0 0 0 7>; > - interrupt-map = <0 0 0 1 &pcie_intc0 0>, > - <0 0 0 2 &pcie_intc0 1>, > - <0 0 0 3 &pcie_intc0 2>, > - <0 0 0 4 &pcie_intc0 3>; > - pcie_intc0: interrupt-controller { > + interrupt-map = <0 0 0 1 &pcie_intc1 0>, > + <0 0 0 2 &pcie_intc1 1>, > + <0 0 0 3 &pcie_intc1 2>, > + <0 0 0 4 &pcie_intc1 3>; > + pcie_intc1: interrupt-controller { > interrupt-controller; > #address-cells = <0>; > #interrupt-cells = <1>; > }; > }; > + }; > > - pcie1: pcie@1,0 { > - reg = <0x0800 0 0 0 0>; > + pcie0: pcie@11700000 { > + compatible = "mediatek,mt2712-pcie"; > + device_type = "pci"; > + reg = <0 0x11700000 0 0x1000>; > + reg-names = "port0"; > + #address-cells = <3>; > + #size-cells = <2>; > + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "pcie_irq"; > + clocks = <&topckgen CLK_TOP_PE2_MAC_P0_SEL>, > + <&pericfg CLK_PERI_PCIE0>; > + clock-names = "sys_ck0", "ahb_ck0"; > + phys = <&u3port0 PHY_TYPE_PCIE>; > + phy-names = "pcie-phy0"; > + bus-range = <0x00 0xff>; > + ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>; > + > + slot0: pcie@0,0 { > + reg = <0x0000 0 0 0 0>; > #address-cells = <3>; > #size-cells = <2>; > #interrupt-cells = <1>; > ranges; > interrupt-map-mask = <0 0 0 7>; > - interrupt-map = <0 0 0 1 &pcie_intc1 0>, > - <0 0 0 2 &pcie_intc1 1>, > - <0 0 0 3 &pcie_intc1 2>, > - <0 0 0 4 &pcie_intc1 3>; > - pcie_intc1: interrupt-controller { > + interrupt-map = <0 0 0 1 &pcie_intc0 0>, > + <0 0 0 2 &pcie_intc0 1>, > + <0 0 0 3 &pcie_intc0 2>, > + <0 0 0 4 &pcie_intc0 3>; > + pcie_intc0: interrupt-controller { > interrupt-controller; > #address-cells = <0>; > #interrupt-cells = <1>; > @@ -202,39 +217,29 @@ Examples for MT2712: > > Examples for MT7622: > > - pcie: pcie@1a140000 { > + pcie0: pcie@1a143000 { > compatible = "mediatek,mt7622-pcie"; > device_type = "pci"; > - reg = <0 0x1a140000 0 0x1000>, > - <0 0x1a143000 0 0x1000>, > - <0 0x1a145000 0 0x1000>; > - reg-names = "subsys", "port0", "port1"; > + reg = <0 0x1a143000 0 0x1000>; > + reg-names = "port0"; > #address-cells = <3>; > #size-cells = <2>; > - interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_LOW>, > - <GIC_SPI 229 IRQ_TYPE_LEVEL_LOW>; > + interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_LOW>; > + interrupt-names = "pcie_irq"; > clocks = <&pciesys CLK_PCIE_P0_MAC_EN>, > - <&pciesys CLK_PCIE_P1_MAC_EN>, > <&pciesys CLK_PCIE_P0_AHB_EN>, > - <&pciesys CLK_PCIE_P1_AHB_EN>, > <&pciesys CLK_PCIE_P0_AUX_EN>, > - <&pciesys CLK_PCIE_P1_AUX_EN>, > <&pciesys CLK_PCIE_P0_AXI_EN>, > - <&pciesys CLK_PCIE_P1_AXI_EN>, > <&pciesys CLK_PCIE_P0_OBFF_EN>, > - <&pciesys CLK_PCIE_P1_OBFF_EN>, > - <&pciesys CLK_PCIE_P0_PIPE_EN>, > - <&pciesys CLK_PCIE_P1_PIPE_EN>; > - clock-names = "sys_ck0", "sys_ck1", "ahb_ck0", "ahb_ck1", > - "aux_ck0", "aux_ck1", "axi_ck0", "axi_ck1", > - "obff_ck0", "obff_ck1", "pipe_ck0", "pipe_ck1"; > - phys = <&pcie0_phy PHY_TYPE_PCIE>, <&pcie1_phy PHY_TYPE_PCIE>; > - phy-names = "pcie-phy0", "pcie-phy1"; > + <&pciesys CLK_PCIE_P0_PIPE_EN>; > + clock-names = "sys_ck0", "ahb_ck0", "aux_ck0", > + "axi_ck0", "obff_ck0", "pipe_ck0"; > + > power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>; > bus-range = <0x00 0xff>; > - ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>; > + ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x8000000>; > > - pcie0: pcie@0,0 { > + slot0: pcie@0,0 { > reg = <0x0000 0 0 0 0>; > #address-cells = <3>; > #size-cells = <2>; > @@ -251,8 +256,32 @@ Examples for MT7622: > #interrupt-cells = <1>; > }; > }; > + }; > + > + pcie1: pcie@1a145000 { > + compatible = "mediatek,mt7622-pcie"; > + device_type = "pci"; > + reg = <0 0x1a145000 0 0x1000>; > + reg-names = "port1"; > + #address-cells = <3>; > + #size-cells = <2>; > + interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_LOW>; > + interrupt-names = "pcie_irq"; > + clocks = <&pciesys CLK_PCIE_P1_MAC_EN>, > + /* designer has connect RC1 with p0_ahb clock */ > + <&pciesys CLK_PCIE_P0_AHB_EN>, > + <&pciesys CLK_PCIE_P1_AUX_EN>, > + <&pciesys CLK_PCIE_P1_AXI_EN>, > + <&pciesys CLK_PCIE_P1_OBFF_EN>, > + <&pciesys CLK_PCIE_P1_PIPE_EN>; > + clock-names = "sys_ck1", "ahb_ck1", "aux_ck1", > + "axi_ck1", "obff_ck1", "pipe_ck1"; > + > + power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>; > + bus-range = <0x00 0xff>; > + ranges = <0x82000000 0 0x28000000 0x0 0x28000000 0 0x8000000>; > > - pcie1: pcie@1,0 { > + slot1: pcie@1,0 { > reg = <0x0800 0 0 0 0>; > #address-cells = <3>; > #size-cells = <2>; > -- > 2.18.0 > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
On Thu, 2020-10-29 at 10:34 -0500, Rob Herring wrote: > On Thu, 29 Oct 2020 16:15:10 +0800, Chuanjia Liu wrote: > > Split the PCIe node and add pciecfg node to fix MSI issue. > > > > Signed-off-by: Chuanjia Liu <chuanjia.liu@mediatek.com> > > Acked-by: Ryder Lee <ryder.lee@mediatek.com> > > --- > > .../bindings/pci/mediatek-pcie-cfg.yaml | 39 ++++++ > > .../devicetree/bindings/pci/mediatek-pcie.txt | 129 +++++++++++------- > > 2 files changed, 118 insertions(+), 50 deletions(-) > > create mode 100644 Documentation/devicetree/bindings/pci/mediatek-pcie-cfg.yaml > > > > > My bot found errors running 'make dt_binding_check' on your patch: > > yamllint warnings/errors: > ./Documentation/devicetree/bindings/pci/mediatek-pcie-cfg.yaml:19:7: [warning] wrong indentation: expected 4 but found 6 (indentation) > > dtschema/dtc warnings/errors: > > > See https://patchwork.ozlabs.org/patch/1389940 > > The base for the patch is generally the last rc1. Any dependencies > should be noted. > > If you already ran 'make dt_binding_check' and didn't see the above > error(s), then make sure 'yamllint' is installed and dt-schema is up to > date: > > pip3 install dtschema --upgrade > > Please check and re-submit. > Thanks for your comment，After install ‘yamllint’ ，I can see this warning ，I will fix it and rebase to 5.10-rc1 in next version.
On Mon, 2020-11-02 at 10:19 -0600, Rob Herring wrote: > On Thu, Oct 29, 2020 at 04:15:10PM +0800, Chuanjia Liu wrote: > > Split the PCIe node and add pciecfg node to fix MSI issue. > > I still think if you are changing the binding this much, then further > work should be done removing the slot nodes. > > > > > Signed-off-by: Chuanjia Liu <chuanjia.liu@mediatek.com> > > Acked-by: Ryder Lee <ryder.lee@mediatek.com> > > --- > > .../bindings/pci/mediatek-pcie-cfg.yaml | 39 ++++++ > > .../devicetree/bindings/pci/mediatek-pcie.txt | 129 +++++++++++------- > > 2 files changed, 118 insertions(+), 50 deletions(-) > > create mode 100644 Documentation/devicetree/bindings/pci/mediatek-pcie-cfg.yaml > > > > diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie-cfg.yaml b/Documentation/devicetree/bindings/pci/mediatek-pcie-cfg.yaml > > new file mode 100644 > > index 000000000000..d3ecbcd032a2 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/pci/mediatek-pcie-cfg.yaml > > @@ -0,0 +1,39 @@ > > +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/pci/mediatek-pcie-cfg.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: Mediatek PCIECFG controller > > + > > +maintainers: > > + - Chuanjia Liu <chuanjia.liu@mediatek.com> > > + - Jianjun Wang <jianjun.wang@mediatek.com> > > + > > +description: | > > + The MediaTek PCIECFG controller controls some feature about > > + LTSSM, ASPM and so on. > > + > > +properties: > > + compatible: > > + items: > > + - enum: > > + - mediatek,generic-pciecfg > > + - const: syscon > > + > > + reg: > > + maxItems: 1 > > + > > +required: > > + - compatible > > + - reg > > + > > +additionalProperties: false > > + > > +examples: > > + - | > > + pciecfg: pciecfg@1a140000 { > > + compatible = "mediatek,generic-pciecfg", "syscon"; > > + reg = <0x1a140000 0x1000>; > > + }; > > +... > > diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt > > index 7468d666763a..c14a2745de37 100644 > > --- a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt > > +++ b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt > > @@ -8,7 +8,7 @@ Required properties: > > "mediatek,mt7623-pcie" > > "mediatek,mt7629-pcie" > > - device_type: Must be "pci" > > -- reg: Base addresses and lengths of the PCIe subsys and root ports. > > +- reg: Base addresses and lengths of the root ports. > > - reg-names: Names of the above areas to use during resource lookup. > > - #address-cells: Address representation for root ports (must be 3) > > - #size-cells: Size representation for root ports (must be 2) > > @@ -143,56 +143,71 @@ Examples for MT7623: > > > > Examples for MT2712: > > > > - pcie: pcie@11700000 { > > + pcie1: pcie@112ff000 { > > compatible = "mediatek,mt2712-pcie"; > > device_type = "pci"; > > - reg = <0 0x11700000 0 0x1000>, > > - <0 0x112ff000 0 0x1000>; > > - reg-names = "port0", "port1"; > > + reg = <0 0x112ff000 0 0x1000>; > > + reg-names = "port1"; > > #address-cells = <3>; > > #size-cells = <2>; > > - interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>, > > - <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; > > - clocks = <&topckgen CLK_TOP_PE2_MAC_P0_SEL>, > > - <&topckgen CLK_TOP_PE2_MAC_P1_SEL>, > > - <&pericfg CLK_PERI_PCIE0>, > > + interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; > > + interrupt-names = "pcie_irq"; > > + clocks = <&topckgen CLK_TOP_PE2_MAC_P1_SEL>, > > <&pericfg CLK_PERI_PCIE1>; > > - clock-names = "sys_ck0", "sys_ck1", "ahb_ck0", "ahb_ck1"; > > - phys = <&pcie0_phy PHY_TYPE_PCIE>, <&pcie1_phy PHY_TYPE_PCIE>; > > - phy-names = "pcie-phy0", "pcie-phy1"; > > + clock-names = "sys_ck1", "ahb_ck1"; > > + phys = <&u3port1 PHY_TYPE_PCIE>; > > + phy-names = "pcie-phy1"; > > bus-range = <0x00 0xff>; > > - ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>; > > + ranges = <0x82000000 0 0x11400000 0x0 0x11400000 0 0x300000>; > > > > - pcie0: pcie@0,0 { > > - reg = <0x0000 0 0 0 0>; > > + slot1: pcie@1,0 { > > Does the driver still work if this is devfn 0 instead of 1 (or swap 0 > and 1 slots)? I'll bet it does. > The driver still work when devfn 0 instead of 1，but the driver and dtsi need some change.Because some setting in the driver is based on slot number to determine offset. > The reason being is that AFAICT, the Mediatek PCI controller is > Designware based. The registers at 0x70c and 0x73c are DWC 'port logic' > registers. The DWC RC also has a quirk that it doesn't filter config > accesses to only devfn 0 (see pci_dw_valid_device()), so your config > accesses to the RP should work no matter what devfn you use. You'll have > to get rid of the ports list and just get the mtk_pcie_port from > bus->sysdata instead. I don’t understand why must get rid of the ports list and get the mtk_pcie_port from bus->sysdata instead. Ports list was retained for compatibility with the old DTS format. And in pci-tegra.c and pci-mvebu.c ,they also have ports list and devfn doesn't start at 0.(e.g:tegra210.dtsi, armada-385.dtsi). >
On Tue, 2020-11-03 at 16:56 -0600, Bjorn Helgaas wrote: > Run "git log --oneline" and follow the convention, e.g., > > dt-bindings: PCI: mediatek: ... > thanks for your comment, I will update to dt-bindings: PCI: mediatek: Update the Device tree bindings > On Thu, Oct 29, 2020 at 04:15:10PM +0800, Chuanjia Liu wrote: > > Split the PCIe node and add pciecfg node to fix MSI issue. > > I assume "split" refers to the new yaml file? It's not really obvious > how the two files are connected. In mt2712 and mt7622,old DTS format is one PCIe controller have two slot. In new DTS, split two independent PCIe controller and a pciecfg node. I once added the "mediatek,pcie-cfg = <&pciecfg>" in PCIe node, but Rob suggested that search for the node by compatible.so I remove it. > Could this be done in two patches? One for the split and one for the > MSI issue? MSI issue is fixed when the PCIe node is separated. So I think this should be one patch. > It'd be nice to say something more about the MSI issue. The detailed description in patch 3/4, I will add description of the msi issue in the next version of this patch. Thanks again for your review. > > > Signed-off-by: Chuanjia Liu <chuanjia.liu@mediatek.com> > > Acked-by: Ryder Lee <ryder.lee@mediatek.com> > > --- > > .../bindings/pci/mediatek-pcie-cfg.yaml | 39 ++++++ > > .../devicetree/bindings/pci/mediatek-pcie.txt | 129 +++++++++++------- > > 2 files changed, 118 insertions(+), 50 deletions(-) > > create mode 100644 Documentation/devicetree/bindings/pci/mediatek-pcie-cfg.yaml > > > > diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie-cfg.yaml b/Documentation/devicetree/bindings/pci/mediatek-pcie-cfg.yaml > > new file mode 100644 > > index 000000000000..d3ecbcd032a2 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/pci/mediatek-pcie-cfg.yaml > > @@ -0,0 +1,39 @@ > > +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/pci/mediatek-pcie-cfg.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: Mediatek PCIECFG controller > > + > > +maintainers: > > + - Chuanjia Liu <chuanjia.liu@mediatek.com> > > + - Jianjun Wang <jianjun.wang@mediatek.com> > > + > > +description: | > > + The MediaTek PCIECFG controller controls some feature about > > + LTSSM, ASPM and so on. > > + > > +properties: > > + compatible: > > + items: > > + - enum: > > + - mediatek,generic-pciecfg > > + - const: syscon > > + > > + reg: > > + maxItems: 1 > > + > > +required: > > + - compatible > > + - reg > > + > > +additionalProperties: false > > + > > +examples: > > + - | > > + pciecfg: pciecfg@1a140000 { > > + compatible = "mediatek,generic-pciecfg", "syscon"; > > + reg = <0x1a140000 0x1000>; > > + }; > > +... > > diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt > > index 7468d666763a..c14a2745de37 100644 > > --- a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt > > +++ b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt > > @@ -8,7 +8,7 @@ Required properties: > > "mediatek,mt7623-pcie" > > "mediatek,mt7629-pcie" > > - device_type: Must be "pci" > > -- reg: Base addresses and lengths of the PCIe subsys and root ports. > > +- reg: Base addresses and lengths of the root ports. > > - reg-names: Names of the above areas to use during resource lookup. > > - #address-cells: Address representation for root ports (must be 3) > > - #size-cells: Size representation for root ports (must be 2) > > @@ -143,56 +143,71 @@ Examples for MT7623: > > > > Examples for MT2712: > > > > - pcie: pcie@11700000 { > > + pcie1: pcie@112ff000 { > > compatible = "mediatek,mt2712-pcie"; > > device_type = "pci"; > > - reg = <0 0x11700000 0 0x1000>, > > - <0 0x112ff000 0 0x1000>; > > - reg-names = "port0", "port1"; > > + reg = <0 0x112ff000 0 0x1000>; > > + reg-names = "port1"; > > #address-cells = <3>; > > #size-cells = <2>; > > - interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>, > > - <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; > > - clocks = <&topckgen CLK_TOP_PE2_MAC_P0_SEL>, > > - <&topckgen CLK_TOP_PE2_MAC_P1_SEL>, > > - <&pericfg CLK_PERI_PCIE0>, > > + interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; > > + interrupt-names = "pcie_irq"; > > + clocks = <&topckgen CLK_TOP_PE2_MAC_P1_SEL>, > > <&pericfg CLK_PERI_PCIE1>; > > - clock-names = "sys_ck0", "sys_ck1", "ahb_ck0", "ahb_ck1"; > > - phys = <&pcie0_phy PHY_TYPE_PCIE>, <&pcie1_phy PHY_TYPE_PCIE>; > > - phy-names = "pcie-phy0", "pcie-phy1"; > > + clock-names = "sys_ck1", "ahb_ck1"; > > + phys = <&u3port1 PHY_TYPE_PCIE>; > > + phy-names = "pcie-phy1"; > > bus-range = <0x00 0xff>; > > - ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>; > > + ranges = <0x82000000 0 0x11400000 0x0 0x11400000 0 0x300000>; > > > > - pcie0: pcie@0,0 { > > - reg = <0x0000 0 0 0 0>; > > + slot1: pcie@1,0 { > > + reg = <0x0800 0 0 0 0>; > > #address-cells = <3>; > > #size-cells = <2>; > > #interrupt-cells = <1>; > > ranges; > > interrupt-map-mask = <0 0 0 7>; > > - interrupt-map = <0 0 0 1 &pcie_intc0 0>, > > - <0 0 0 2 &pcie_intc0 1>, > > - <0 0 0 3 &pcie_intc0 2>, > > - <0 0 0 4 &pcie_intc0 3>; > > - pcie_intc0: interrupt-controller { > > + interrupt-map = <0 0 0 1 &pcie_intc1 0>, > > + <0 0 0 2 &pcie_intc1 1>, > > + <0 0 0 3 &pcie_intc1 2>, > > + <0 0 0 4 &pcie_intc1 3>; > > + pcie_intc1: interrupt-controller { > > interrupt-controller; > > #address-cells = <0>; > > #interrupt-cells = <1>; > > }; > > }; > > + }; > > > > - pcie1: pcie@1,0 { > > - reg = <0x0800 0 0 0 0>; > > + pcie0: pcie@11700000 { > > + compatible = "mediatek,mt2712-pcie"; > > + device_type = "pci"; > > + reg = <0 0x11700000 0 0x1000>; > > + reg-names = "port0"; > > + #address-cells = <3>; > > + #size-cells = <2>; > > + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>; > > + interrupt-names = "pcie_irq"; > > + clocks = <&topckgen CLK_TOP_PE2_MAC_P0_SEL>, > > + <&pericfg CLK_PERI_PCIE0>; > > + clock-names = "sys_ck0", "ahb_ck0"; > > + phys = <&u3port0 PHY_TYPE_PCIE>; > > + phy-names = "pcie-phy0"; > > + bus-range = <0x00 0xff>; > > + ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>; > > + > > + slot0: pcie@0,0 { > > + reg = <0x0000 0 0 0 0>; > > #address-cells = <3>; > > #size-cells = <2>; > > #interrupt-cells = <1>; > > ranges; > > interrupt-map-mask = <0 0 0 7>; > > - interrupt-map = <0 0 0 1 &pcie_intc1 0>, > > - <0 0 0 2 &pcie_intc1 1>, > > - <0 0 0 3 &pcie_intc1 2>, > > - <0 0 0 4 &pcie_intc1 3>; > > - pcie_intc1: interrupt-controller { > > + interrupt-map = <0 0 0 1 &pcie_intc0 0>, > > + <0 0 0 2 &pcie_intc0 1>, > > + <0 0 0 3 &pcie_intc0 2>, > > + <0 0 0 4 &pcie_intc0 3>; > > + pcie_intc0: interrupt-controller { > > interrupt-controller; > > #address-cells = <0>; > > #interrupt-cells = <1>; > > @@ -202,39 +217,29 @@ Examples for MT2712: > > > > Examples for MT7622: > > > > - pcie: pcie@1a140000 { > > + pcie0: pcie@1a143000 { > > compatible = "mediatek,mt7622-pcie"; > > device_type = "pci"; > > - reg = <0 0x1a140000 0 0x1000>, > > - <0 0x1a143000 0 0x1000>, > > - <0 0x1a145000 0 0x1000>; > > - reg-names = "subsys", "port0", "port1"; > > + reg = <0 0x1a143000 0 0x1000>; > > + reg-names = "port0"; > > #address-cells = <3>; > > #size-cells = <2>; > > - interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_LOW>, > > - <GIC_SPI 229 IRQ_TYPE_LEVEL_LOW>; > > + interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_LOW>; > > + interrupt-names = "pcie_irq"; > > clocks = <&pciesys CLK_PCIE_P0_MAC_EN>, > > - <&pciesys CLK_PCIE_P1_MAC_EN>, > > <&pciesys CLK_PCIE_P0_AHB_EN>, > > - <&pciesys CLK_PCIE_P1_AHB_EN>, > > <&pciesys CLK_PCIE_P0_AUX_EN>, > > - <&pciesys CLK_PCIE_P1_AUX_EN>, > > <&pciesys CLK_PCIE_P0_AXI_EN>, > > - <&pciesys CLK_PCIE_P1_AXI_EN>, > > <&pciesys CLK_PCIE_P0_OBFF_EN>, > > - <&pciesys CLK_PCIE_P1_OBFF_EN>, > > - <&pciesys CLK_PCIE_P0_PIPE_EN>, > > - <&pciesys CLK_PCIE_P1_PIPE_EN>; > > - clock-names = "sys_ck0", "sys_ck1", "ahb_ck0", "ahb_ck1", > > - "aux_ck0", "aux_ck1", "axi_ck0", "axi_ck1", > > - "obff_ck0", "obff_ck1", "pipe_ck0", "pipe_ck1"; > > - phys = <&pcie0_phy PHY_TYPE_PCIE>, <&pcie1_phy PHY_TYPE_PCIE>; > > - phy-names = "pcie-phy0", "pcie-phy1"; > > + <&pciesys CLK_PCIE_P0_PIPE_EN>; > > + clock-names = "sys_ck0", "ahb_ck0", "aux_ck0", > > + "axi_ck0", "obff_ck0", "pipe_ck0"; > > + > > power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>; > > bus-range = <0x00 0xff>; > > - ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>; > > + ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x8000000>; > > > > - pcie0: pcie@0,0 { > > + slot0: pcie@0,0 { > > reg = <0x0000 0 0 0 0>; > > #address-cells = <3>; > > #size-cells = <2>; > > @@ -251,8 +256,32 @@ Examples for MT7622: > > #interrupt-cells = <1>; > > }; > > }; > > + }; > > + > > + pcie1: pcie@1a145000 { > > + compatible = "mediatek,mt7622-pcie"; > > + device_type = "pci"; > > + reg = <0 0x1a145000 0 0x1000>; > > + reg-names = "port1"; > > + #address-cells = <3>; > > + #size-cells = <2>; > > + interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_LOW>; > > + interrupt-names = "pcie_irq"; > > + clocks = <&pciesys CLK_PCIE_P1_MAC_EN>, > > + /* designer has connect RC1 with p0_ahb clock */ > > + <&pciesys CLK_PCIE_P0_AHB_EN>, > > + <&pciesys CLK_PCIE_P1_AUX_EN>, > > + <&pciesys CLK_PCIE_P1_AXI_EN>, > > + <&pciesys CLK_PCIE_P1_OBFF_EN>, > > + <&pciesys CLK_PCIE_P1_PIPE_EN>; > > + clock-names = "sys_ck1", "ahb_ck1", "aux_ck1", > > + "axi_ck1", "obff_ck1", "pipe_ck1"; > > + > > + power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>; > > + bus-range = <0x00 0xff>; > > + ranges = <0x82000000 0 0x28000000 0x0 0x28000000 0 0x8000000>; > > > > - pcie1: pcie@1,0 { > > + slot1: pcie@1,0 { > > reg = <0x0800 0 0 0 0>; > > #address-cells = <3>; > > #size-cells = <2>; > > -- > > 2.18.0 > > _______________________________________________ > > linux-arm-kernel mailing list > > linux-arm-kernel@lists.infradead.org > > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie-cfg.yaml b/Documentation/devicetree/bindings/pci/mediatek-pcie-cfg.yaml new file mode 100644 index 000000000000..d3ecbcd032a2 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/mediatek-pcie-cfg.yaml @@ -0,0 +1,39 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pci/mediatek-pcie-cfg.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Mediatek PCIECFG controller + +maintainers: + - Chuanjia Liu <chuanjia.liu@mediatek.com> + - Jianjun Wang <jianjun.wang@mediatek.com> + +description: | + The MediaTek PCIECFG controller controls some feature about + LTSSM, ASPM and so on. + +properties: + compatible: + items: + - enum: + - mediatek,generic-pciecfg + - const: syscon + + reg: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + pciecfg: pciecfg@1a140000 { + compatible = "mediatek,generic-pciecfg", "syscon"; + reg = <0x1a140000 0x1000>; + }; +... diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt index 7468d666763a..c14a2745de37 100644 --- a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt +++ b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt @@ -8,7 +8,7 @@ Required properties: "mediatek,mt7623-pcie" "mediatek,mt7629-pcie" - device_type: Must be "pci" -- reg: Base addresses and lengths of the PCIe subsys and root ports. +- reg: Base addresses and lengths of the root ports. - reg-names: Names of the above areas to use during resource lookup. - #address-cells: Address representation for root ports (must be 3) - #size-cells: Size representation for root ports (must be 2) @@ -143,56 +143,71 @@ Examples for MT7623: Examples for MT2712: - pcie: pcie@11700000 { + pcie1: pcie@112ff000 { compatible = "mediatek,mt2712-pcie"; device_type = "pci"; - reg = <0 0x11700000 0 0x1000>, - <0 0x112ff000 0 0x1000>; - reg-names = "port0", "port1"; + reg = <0 0x112ff000 0 0x1000>; + reg-names = "port1"; #address-cells = <3>; #size-cells = <2>; - interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&topckgen CLK_TOP_PE2_MAC_P0_SEL>, - <&topckgen CLK_TOP_PE2_MAC_P1_SEL>, - <&pericfg CLK_PERI_PCIE0>, + interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "pcie_irq"; + clocks = <&topckgen CLK_TOP_PE2_MAC_P1_SEL>, <&pericfg CLK_PERI_PCIE1>; - clock-names = "sys_ck0", "sys_ck1", "ahb_ck0", "ahb_ck1"; - phys = <&pcie0_phy PHY_TYPE_PCIE>, <&pcie1_phy PHY_TYPE_PCIE>; - phy-names = "pcie-phy0", "pcie-phy1"; + clock-names = "sys_ck1", "ahb_ck1"; + phys = <&u3port1 PHY_TYPE_PCIE>; + phy-names = "pcie-phy1"; bus-range = <0x00 0xff>; - ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>; + ranges = <0x82000000 0 0x11400000 0x0 0x11400000 0 0x300000>; - pcie0: pcie@0,0 { - reg = <0x0000 0 0 0 0>; + slot1: pcie@1,0 { + reg = <0x0800 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; #interrupt-cells = <1>; ranges; interrupt-map-mask = <0 0 0 7>; - interrupt-map = <0 0 0 1 &pcie_intc0 0>, - <0 0 0 2 &pcie_intc0 1>, - <0 0 0 3 &pcie_intc0 2>, - <0 0 0 4 &pcie_intc0 3>; - pcie_intc0: interrupt-controller { + interrupt-map = <0 0 0 1 &pcie_intc1 0>, + <0 0 0 2 &pcie_intc1 1>, + <0 0 0 3 &pcie_intc1 2>, + <0 0 0 4 &pcie_intc1 3>; + pcie_intc1: interrupt-controller { interrupt-controller; #address-cells = <0>; #interrupt-cells = <1>; }; }; + }; - pcie1: pcie@1,0 { - reg = <0x0800 0 0 0 0>; + pcie0: pcie@11700000 { + compatible = "mediatek,mt2712-pcie"; + device_type = "pci"; + reg = <0 0x11700000 0 0x1000>; + reg-names = "port0"; + #address-cells = <3>; + #size-cells = <2>; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "pcie_irq"; + clocks = <&topckgen CLK_TOP_PE2_MAC_P0_SEL>, + <&pericfg CLK_PERI_PCIE0>; + clock-names = "sys_ck0", "ahb_ck0"; + phys = <&u3port0 PHY_TYPE_PCIE>; + phy-names = "pcie-phy0"; + bus-range = <0x00 0xff>; + ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>; + + slot0: pcie@0,0 { + reg = <0x0000 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; #interrupt-cells = <1>; ranges; interrupt-map-mask = <0 0 0 7>; - interrupt-map = <0 0 0 1 &pcie_intc1 0>, - <0 0 0 2 &pcie_intc1 1>, - <0 0 0 3 &pcie_intc1 2>, - <0 0 0 4 &pcie_intc1 3>; - pcie_intc1: interrupt-controller { + interrupt-map = <0 0 0 1 &pcie_intc0 0>, + <0 0 0 2 &pcie_intc0 1>, + <0 0 0 3 &pcie_intc0 2>, + <0 0 0 4 &pcie_intc0 3>; + pcie_intc0: interrupt-controller { interrupt-controller; #address-cells = <0>; #interrupt-cells = <1>; @@ -202,39 +217,29 @@ Examples for MT2712: Examples for MT7622: - pcie: pcie@1a140000 { + pcie0: pcie@1a143000 { compatible = "mediatek,mt7622-pcie"; device_type = "pci"; - reg = <0 0x1a140000 0 0x1000>, - <0 0x1a143000 0 0x1000>, - <0 0x1a145000 0 0x1000>; - reg-names = "subsys", "port0", "port1"; + reg = <0 0x1a143000 0 0x1000>; + reg-names = "port0"; #address-cells = <3>; #size-cells = <2>; - interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_LOW>, - <GIC_SPI 229 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "pcie_irq"; clocks = <&pciesys CLK_PCIE_P0_MAC_EN>, - <&pciesys CLK_PCIE_P1_MAC_EN>, <&pciesys CLK_PCIE_P0_AHB_EN>, - <&pciesys CLK_PCIE_P1_AHB_EN>, <&pciesys CLK_PCIE_P0_AUX_EN>, - <&pciesys CLK_PCIE_P1_AUX_EN>, <&pciesys CLK_PCIE_P0_AXI_EN>, - <&pciesys CLK_PCIE_P1_AXI_EN>, <&pciesys CLK_PCIE_P0_OBFF_EN>, - <&pciesys CLK_PCIE_P1_OBFF_EN>, - <&pciesys CLK_PCIE_P0_PIPE_EN>, - <&pciesys CLK_PCIE_P1_PIPE_EN>; - clock-names = "sys_ck0", "sys_ck1", "ahb_ck0", "ahb_ck1", - "aux_ck0", "aux_ck1", "axi_ck0", "axi_ck1", - "obff_ck0", "obff_ck1", "pipe_ck0", "pipe_ck1"; - phys = <&pcie0_phy PHY_TYPE_PCIE>, <&pcie1_phy PHY_TYPE_PCIE>; - phy-names = "pcie-phy0", "pcie-phy1"; + <&pciesys CLK_PCIE_P0_PIPE_EN>; + clock-names = "sys_ck0", "ahb_ck0", "aux_ck0", + "axi_ck0", "obff_ck0", "pipe_ck0"; + power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>; bus-range = <0x00 0xff>; - ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>; + ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x8000000>; - pcie0: pcie@0,0 { + slot0: pcie@0,0 { reg = <0x0000 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; @@ -251,8 +256,32 @@ Examples for MT7622: #interrupt-cells = <1>; }; }; + }; + + pcie1: pcie@1a145000 { + compatible = "mediatek,mt7622-pcie"; + device_type = "pci"; + reg = <0 0x1a145000 0 0x1000>; + reg-names = "port1"; + #address-cells = <3>; + #size-cells = <2>; + interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "pcie_irq"; + clocks = <&pciesys CLK_PCIE_P1_MAC_EN>, + /* designer has connect RC1 with p0_ahb clock */ + <&pciesys CLK_PCIE_P0_AHB_EN>, + <&pciesys CLK_PCIE_P1_AUX_EN>, + <&pciesys CLK_PCIE_P1_AXI_EN>, + <&pciesys CLK_PCIE_P1_OBFF_EN>, + <&pciesys CLK_PCIE_P1_PIPE_EN>; + clock-names = "sys_ck1", "ahb_ck1", "aux_ck1", + "axi_ck1", "obff_ck1", "pipe_ck1"; + + power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>; + bus-range = <0x00 0xff>; + ranges = <0x82000000 0 0x28000000 0x0 0x28000000 0 0x8000000>; - pcie1: pcie@1,0 { + slot1: pcie@1,0 { reg = <0x0800 0 0 0 0>; #address-cells = <3>; #size-cells = <2>;