| Message ID | 20201202135409.13683-9-andre.przywara@arm.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | arm64: sunxi: Initial Allwinner H616 SoC support | expand |
在 2020-12-02星期三的 13:54 +0000，Andre Przywara写道： > The OrangePi Zero 2 is a development board with the new H616 SoC. > > It features the usual connectors used on those small boards, and > comes > with the AXP305, which seems to be compatible with the AXP805. > > For more details see: http://linux-sunxi.org/Xunlong_Orange_Pi_Zero2 > > Signed-off-by: Andre Przywara <andre.przywara@arm.com> > --- > arch/arm64/boot/dts/allwinner/Makefile | 1 + > .../allwinner/sun50i-h616-orangepi-zero2.dts | 228 > ++++++++++++++++++ > 2 files changed, 229 insertions(+) > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616- > orangepi-zero2.dts > > diff --git a/arch/arm64/boot/dts/allwinner/Makefile > b/arch/arm64/boot/dts/allwinner/Makefile > index 211d1e9d4701..0cf8299b1ce7 100644 > --- a/arch/arm64/boot/dts/allwinner/Makefile > +++ b/arch/arm64/boot/dts/allwinner/Makefile > @@ -35,3 +35,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one- > plus.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb > +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi- > zero2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi- > zero2.dts > new file mode 100644 > index 000000000000..814f5b4fec7c > --- /dev/null > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts > @@ -0,0 +1,228 @@ > +// SPDX-License-Identifier: (GPL-2.0+ or MIT) > +/* > + * Copyright (C) 2020 Arm Ltd. > + */ > + > +/dts-v1/; > + > +#include "sun50i-h616.dtsi" > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/interrupt-controller/arm-gic.h> > + > +/ { > + model = "OrangePi Zero2"; > + compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616"; > + > + aliases { > + ethernet0 = &emac0; > + serial0 = &uart0; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + power { > + label = "orangepi:red:power"; > + gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 > */ > + default-state = "on"; > + }; > + > + status { > + label = "orangepi:green:status"; > + gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 > */ > + }; > + }; > + > + reg_vcc5v: vcc5v { > + /* board wide 5V supply directly from the USB-C socket > */ > + compatible = "regulator-fixed"; > + regulator-name = "vcc-5v"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + }; > + > + reg_usb1_vbus: usb1-vbus { > + compatible = "regulator-fixed"; > + regulator-name = "usb1-vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */ > + status = "okay"; > + }; > +}; > + > +&ehci0 { > + status = "okay"; > +}; > + > +&ehci1 { > + status = "okay"; > +}; > + > +/* USB 2 & 3 are on headers only. */ > + > +&emac0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&ext_rgmii_pins>; > + phy-mode = "rgmii"; > + phy-handle = <&ext_rgmii_phy>; > + phy-supply = <®_dcdce>; > + allwinner,rx-delay-ps = <3100>; > + allwinner,tx-delay-ps = <700>; > + status = "okay"; > +}; > + > +&mdio { > + ext_rgmii_phy: ethernet-phy@1 { > + compatible = "ethernet-phy-ieee802.3-c22"; > + reg = <1>; > + }; > +}; > + > +&mmc0 { > + vmmc-supply = <®_dcdce>; > + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ > + bus-width = <4>; > + status = "okay"; > +}; > + > +&ohci0 { > + status = "okay"; > +}; > + > +&ohci1 { > + status = "okay"; > +}; > + > +&r_i2c { > + status = "okay"; > + > + axp305: pmic@36 { > + compatible = "x-powers,axp305", "x-powers,axp805", > + "x-powers,axp806"; > + reg = <0x36>; > + > + /* dummy interrupt to appease the driver for now */ > + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-controller; > + #interrupt-cells = <1>; Is dummy interrupt future-proof? > + > + x-powers,self-working-mode; > + vina-supply = <®_vcc5v>; > + vinb-supply = <®_vcc5v>; > + vinc-supply = <®_vcc5v>; > + vind-supply = <®_vcc5v>; > + vine-supply = <®_vcc5v>; > + aldoin-supply = <®_vcc5v>; > + bldoin-supply = <®_vcc5v>; > + cldoin-supply = <®_vcc5v>; > + > + regulators { > + reg_aldo1: aldo1 { > + regulator-always-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc-sys"; > + }; > + > + reg_aldo2: aldo2 { > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc3v3-ext"; > + }; > + > + reg_aldo3: aldo3 { > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc3v3-ext2"; > + }; > + > + reg_bldo1: bldo1 { > + regulator-always-on; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcc1v8"; > + }; > + > + bldo2 { > + /* unused */ > + }; > + > + bldo3 { > + /* unused */ > + }; > + > + bldo4 { > + /* unused */ > + }; > + > + cldo1 { > + /* reserved */ > + }; > + > + cldo2 { > + /* unused */ > + }; > + > + cldo3 { > + /* unused */ > + }; > + > + reg_dcdca: dcdca { > + regulator-always-on; > + regulator-min-microvolt = <810000>; > + regulator-max-microvolt = <1080000>; > + regulator-name = "vdd-cpu"; > + }; > + > + reg_dcdcc: dcdcc { > + regulator-always-on; > + regulator-min-microvolt = <810000>; > + regulator-max-microvolt = <1080000>; > + regulator-name = "vdd-gpu-sys"; > + }; > + > + reg_dcdcd: dcdcd { > + regulator-always-on; > + regulator-min-microvolt = <1500000>; > + regulator-max-microvolt = <1500000>; > + regulator-name = "vdd-dram"; > + }; > + > + reg_dcdce: dcdce { > + regulator-boot-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc-eth-mmc"; > + }; > + > + sw { > + /* unused */ > + }; > + }; > + }; > +}; > + > +&uart0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart0_ph_pins>; > + status = "okay"; > +}; > + > +&usbotg { > + dr_mode = "otg"; The board is locked to a UFP due to fixed resistor on CC. OTG is not possible. > + status = "okay"; > +}; > + > +&usbphy { > + usb0_vbus-supply = <®_vcc5v>; > + usb1_vbus-supply = <®_usb1_vbus>; > + status = "okay"; > +};
On Wed, Dec 02, 2020 at 01:54:09PM +0000, Andre Przywara wrote: > The OrangePi Zero 2 is a development board with the new H616 SoC. > > It features the usual connectors used on those small boards, and comes > with the AXP305, which seems to be compatible with the AXP805. > > For more details see: http://linux-sunxi.org/Xunlong_Orange_Pi_Zero2 > > Signed-off-by: Andre Przywara <andre.przywara@arm.com> > --- > arch/arm64/boot/dts/allwinner/Makefile | 1 + > .../allwinner/sun50i-h616-orangepi-zero2.dts | 228 ++++++++++++++++++ > 2 files changed, 229 insertions(+) > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts > > diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile > index 211d1e9d4701..0cf8299b1ce7 100644 > --- a/arch/arm64/boot/dts/allwinner/Makefile > +++ b/arch/arm64/boot/dts/allwinner/Makefile > @@ -35,3 +35,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb > +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts > new file mode 100644 > index 000000000000..814f5b4fec7c > --- /dev/null > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts > @@ -0,0 +1,228 @@ > +// SPDX-License-Identifier: (GPL-2.0+ or MIT) > +/* > + * Copyright (C) 2020 Arm Ltd. > + */ > + > +/dts-v1/; > + > +#include "sun50i-h616.dtsi" > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/interrupt-controller/arm-gic.h> > + > +/ { > + model = "OrangePi Zero2"; > + compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616"; This needs to be documented too > + aliases { > + ethernet0 = &emac0; > + serial0 = &uart0; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + power { > + label = "orangepi:red:power"; > + gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */ > + default-state = "on"; > + }; > + > + status { > + label = "orangepi:green:status"; > + gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */ > + }; Those node names don't follow the led binding convention > + }; > + > + reg_vcc5v: vcc5v { > + /* board wide 5V supply directly from the USB-C socket */ > + compatible = "regulator-fixed"; > + regulator-name = "vcc-5v"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + }; > + > + reg_usb1_vbus: usb1-vbus { > + compatible = "regulator-fixed"; > + regulator-name = "usb1-vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */ > + status = "okay"; > + }; > +}; > + > +&ehci0 { > + status = "okay"; > +}; > + > +&ehci1 { > + status = "okay"; > +}; > + > +/* USB 2 & 3 are on headers only. */ > + > +&emac0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&ext_rgmii_pins>; > + phy-mode = "rgmii"; > + phy-handle = <&ext_rgmii_phy>; > + phy-supply = <®_dcdce>; > + allwinner,rx-delay-ps = <3100>; > + allwinner,tx-delay-ps = <700>; > + status = "okay"; > +}; > + > +&mdio { > + ext_rgmii_phy: ethernet-phy@1 { > + compatible = "ethernet-phy-ieee802.3-c22"; > + reg = <1>; > + }; > +}; > + > +&mmc0 { > + vmmc-supply = <®_dcdce>; > + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ > + bus-width = <4>; > + status = "okay"; > +}; > + > +&ohci0 { > + status = "okay"; > +}; > + > +&ohci1 { > + status = "okay"; > +}; > + > +&r_i2c { > + status = "okay"; > + > + axp305: pmic@36 { > + compatible = "x-powers,axp305", "x-powers,axp805", > + "x-powers,axp806"; > + reg = <0x36>; > + > + /* dummy interrupt to appease the driver for now */ > + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-controller; > + #interrupt-cells = <1>; > + > + x-powers,self-working-mode; > + vina-supply = <®_vcc5v>; > + vinb-supply = <®_vcc5v>; > + vinc-supply = <®_vcc5v>; > + vind-supply = <®_vcc5v>; > + vine-supply = <®_vcc5v>; > + aldoin-supply = <®_vcc5v>; > + bldoin-supply = <®_vcc5v>; > + cldoin-supply = <®_vcc5v>; > + > + regulators { > + reg_aldo1: aldo1 { > + regulator-always-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc-sys"; > + }; > + > + reg_aldo2: aldo2 { > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc3v3-ext"; > + }; > + > + reg_aldo3: aldo3 { > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc3v3-ext2"; > + }; > + > + reg_bldo1: bldo1 { > + regulator-always-on; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcc1v8"; > + }; > + > + bldo2 { > + /* unused */ > + }; > + > + bldo3 { > + /* unused */ > + }; > + > + bldo4 { > + /* unused */ > + }; > + > + cldo1 { > + /* reserved */ > + }; > + > + cldo2 { > + /* unused */ > + }; > + > + cldo3 { > + /* unused */ > + }; > + > + reg_dcdca: dcdca { > + regulator-always-on; > + regulator-min-microvolt = <810000>; > + regulator-max-microvolt = <1080000>; > + regulator-name = "vdd-cpu"; > + }; > + > + reg_dcdcc: dcdcc { > + regulator-always-on; > + regulator-min-microvolt = <810000>; > + regulator-max-microvolt = <1080000>; > + regulator-name = "vdd-gpu-sys"; > + }; > + > + reg_dcdcd: dcdcd { > + regulator-always-on; > + regulator-min-microvolt = <1500000>; > + regulator-max-microvolt = <1500000>; > + regulator-name = "vdd-dram"; > + }; > + > + reg_dcdce: dcdce { > + regulator-boot-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc-eth-mmc"; > + }; > + > + sw { > + /* unused */ > + }; > + }; > + }; > +}; > + > +&uart0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart0_ph_pins>; > + status = "okay"; > +}; > + > +&usbotg { > + dr_mode = "otg"; > + status = "okay"; > +}; > + > +&usbphy { > + usb0_vbus-supply = <®_vcc5v>; > + usb1_vbus-supply = <®_usb1_vbus>; > + status = "okay"; > +}; Did you really test it as OTG without an ID pin? Maxime
Dne sreda, 02. december 2020 ob 17:07:02 CET je Maxime Ripard napisal(a): > On Wed, Dec 02, 2020 at 01:54:09PM +0000, Andre Przywara wrote: > > The OrangePi Zero 2 is a development board with the new H616 SoC. > > > > It features the usual connectors used on those small boards, and comes > > with the AXP305, which seems to be compatible with the AXP805. > > > > For more details see: http://linux-sunxi.org/Xunlong_Orange_Pi_Zero2 > > > > Signed-off-by: Andre Przywara <andre.przywara@arm.com> > > --- > > arch/arm64/boot/dts/allwinner/Makefile | 1 + > > .../allwinner/sun50i-h616-orangepi-zero2.dts | 228 ++++++++++++++++++ > > 2 files changed, 229 insertions(+) > > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi- zero2.dts > > > > diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/ allwinner/Makefile > > index 211d1e9d4701..0cf8299b1ce7 100644 > > --- a/arch/arm64/boot/dts/allwinner/Makefile > > +++ b/arch/arm64/boot/dts/allwinner/Makefile > > @@ -35,3 +35,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one- plus.dtb > > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb > > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb > > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb > > +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb > > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts > > new file mode 100644 > > index 000000000000..814f5b4fec7c > > --- /dev/null > > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts > > @@ -0,0 +1,228 @@ > > +// SPDX-License-Identifier: (GPL-2.0+ or MIT) > > +/* > > + * Copyright (C) 2020 Arm Ltd. > > + */ > > + > > +/dts-v1/; > > + > > +#include "sun50i-h616.dtsi" > > + > > +#include <dt-bindings/gpio/gpio.h> > > +#include <dt-bindings/interrupt-controller/arm-gic.h> > > + > > +/ { > > + model = "OrangePi Zero2"; > > + compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616"; > > This needs to be documented too > > > + aliases { > > + ethernet0 = &emac0; > > + serial0 = &uart0; > > + }; > > + > > + chosen { > > + stdout-path = "serial0:115200n8"; > > + }; > > + > > + leds { > > + compatible = "gpio-leds"; > > + > > + power { > > + label = "orangepi:red:power"; > > + gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */ > > + default-state = "on"; > > + }; > > + > > + status { > > + label = "orangepi:green:status"; > > + gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */ > > + }; > > Those node names don't follow the led binding convention > > > + }; > > + > > + reg_vcc5v: vcc5v { > > + /* board wide 5V supply directly from the USB-C socket */ > > + compatible = "regulator-fixed"; > > + regulator-name = "vcc-5v"; > > + regulator-min-microvolt = <5000000>; > > + regulator-max-microvolt = <5000000>; > > + regulator-always-on; > > + }; > > + > > + reg_usb1_vbus: usb1-vbus { > > + compatible = "regulator-fixed"; > > + regulator-name = "usb1-vbus"; > > + regulator-min-microvolt = <5000000>; > > + regulator-max-microvolt = <5000000>; > > + enable-active-high; > > + gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */ > > + status = "okay"; > > + }; > > +}; > > + > > +&ehci0 { > > + status = "okay"; > > +}; > > + > > +&ehci1 { > > + status = "okay"; > > +}; > > + > > +/* USB 2 & 3 are on headers only. */ > > + > > +&emac0 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&ext_rgmii_pins>; > > + phy-mode = "rgmii"; > > + phy-handle = <&ext_rgmii_phy>; > > + phy-supply = <®_dcdce>; > > + allwinner,rx-delay-ps = <3100>; > > + allwinner,tx-delay-ps = <700>; > > + status = "okay"; > > +}; > > + > > +&mdio { > > + ext_rgmii_phy: ethernet-phy@1 { > > + compatible = "ethernet-phy-ieee802.3-c22"; > > + reg = <1>; > > + }; > > +}; > > + > > +&mmc0 { > > + vmmc-supply = <®_dcdce>; > > + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ > > + bus-width = <4>; > > + status = "okay"; > > +}; > > + > > +&ohci0 { > > + status = "okay"; > > +}; > > + > > +&ohci1 { > > + status = "okay"; > > +}; > > + > > +&r_i2c { > > + status = "okay"; > > + > > + axp305: pmic@36 { > > + compatible = "x-powers,axp305", "x-powers,axp805", > > + "x-powers,axp806"; > > + reg = <0x36>; > > + > > + /* dummy interrupt to appease the driver for now */ > > + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; > > + interrupt-controller; > > + #interrupt-cells = <1>; > > + > > + x-powers,self-working-mode; > > + vina-supply = <®_vcc5v>; > > + vinb-supply = <®_vcc5v>; > > + vinc-supply = <®_vcc5v>; > > + vind-supply = <®_vcc5v>; > > + vine-supply = <®_vcc5v>; > > + aldoin-supply = <®_vcc5v>; > > + bldoin-supply = <®_vcc5v>; > > + cldoin-supply = <®_vcc5v>; > > + > > + regulators { > > + reg_aldo1: aldo1 { > > + regulator-always-on; > > + regulator-min-microvolt = <3300000>; > > + regulator-max-microvolt = <3300000>; > > + regulator-name = "vcc-sys"; > > + }; > > + > > + reg_aldo2: aldo2 { > > + regulator-min-microvolt = <3300000>; > > + regulator-max-microvolt = <3300000>; > > + regulator-name = "vcc3v3-ext"; > > + }; > > + > > + reg_aldo3: aldo3 { > > + regulator-min-microvolt = <3300000>; > > + regulator-max-microvolt = <3300000>; > > + regulator-name = "vcc3v3-ext2"; > > + }; > > + > > + reg_bldo1: bldo1 { > > + regulator-always-on; > > + regulator-min-microvolt = <1800000>; > > + regulator-max-microvolt = <1800000>; > > + regulator-name = "vcc1v8"; > > + }; > > + > > + bldo2 { > > + /* unused */ > > + }; > > + > > + bldo3 { > > + /* unused */ > > + }; > > + > > + bldo4 { > > + /* unused */ > > + }; > > + > > + cldo1 { > > + /* reserved */ > > + }; > > + > > + cldo2 { > > + /* unused */ > > + }; > > + > > + cldo3 { > > + /* unused */ > > + }; > > + > > + reg_dcdca: dcdca { > > + regulator-always-on; > > + regulator-min-microvolt = <810000>; > > + regulator-max-microvolt = <1080000>; > > + regulator-name = "vdd-cpu"; > > + }; > > + > > + reg_dcdcc: dcdcc { > > + regulator-always-on; > > + regulator-min-microvolt = <810000>; > > + regulator-max-microvolt = <1080000>; > > + regulator-name = "vdd-gpu-sys"; > > + }; > > + > > + reg_dcdcd: dcdcd { > > + regulator-always-on; > > + regulator-min-microvolt = <1500000>; > > + regulator-max-microvolt = <1500000>; > > + regulator-name = "vdd-dram"; > > + }; > > + > > + reg_dcdce: dcdce { > > + regulator-boot-on; > > + regulator-min-microvolt = <3300000>; > > + regulator-max-microvolt = <3300000>; > > + regulator-name = "vcc-eth-mmc"; > > + }; > > + > > + sw { > > + /* unused */ > > + }; > > + }; > > + }; > > +}; > > + > > +&uart0 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&uart0_ph_pins>; > > + status = "okay"; > > +}; > > + > > +&usbotg { > > + dr_mode = "otg"; > > + status = "okay"; > > +}; > > + > > +&usbphy { > > + usb0_vbus-supply = <®_vcc5v>; > > + usb1_vbus-supply = <®_usb1_vbus>; > > + status = "okay"; > > +}; > > Did you really test it as OTG without an ID pin? As stated in cover letter, USB doesn't work yet. USB related nodes, both here and DTSI should be dropped until they work. Best regards, Jernej
On 02/12/2020 15:57, Icenowy Zheng wrote: > 在 2020-12-02星期三的 13:54 +0000，Andre Przywara写道： >> The OrangePi Zero 2 is a development board with the new H616 SoC. >> >> It features the usual connectors used on those small boards, and >> comes >> with the AXP305, which seems to be compatible with the AXP805. >> >> For more details see: http://linux-sunxi.org/Xunlong_Orange_Pi_Zero2 >> >> Signed-off-by: Andre Przywara <andre.przywara@arm.com> >> --- >> arch/arm64/boot/dts/allwinner/Makefile | 1 + >> .../allwinner/sun50i-h616-orangepi-zero2.dts | 228 >> ++++++++++++++++++ >> 2 files changed, 229 insertions(+) >> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616- >> orangepi-zero2.dts >> >> diff --git a/arch/arm64/boot/dts/allwinner/Makefile >> b/arch/arm64/boot/dts/allwinner/Makefile >> index 211d1e9d4701..0cf8299b1ce7 100644 >> --- a/arch/arm64/boot/dts/allwinner/Makefile >> +++ b/arch/arm64/boot/dts/allwinner/Makefile >> @@ -35,3 +35,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one- >> plus.dtb >> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb >> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb >> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb >> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb >> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi- >> zero2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi- >> zero2.dts >> new file mode 100644 >> index 000000000000..814f5b4fec7c >> --- /dev/null >> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts >> @@ -0,0 +1,228 @@ >> +// SPDX-License-Identifier: (GPL-2.0+ or MIT) >> +/* >> + * Copyright (C) 2020 Arm Ltd. >> + */ >> + >> +/dts-v1/; >> + >> +#include "sun50i-h616.dtsi" >> + >> +#include <dt-bindings/gpio/gpio.h> >> +#include <dt-bindings/interrupt-controller/arm-gic.h> >> + >> +/ { >> + model = "OrangePi Zero2"; >> + compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616"; >> + >> + aliases { >> + ethernet0 = &emac0; >> + serial0 = &uart0; >> + }; >> + >> + chosen { >> + stdout-path = "serial0:115200n8"; >> + }; >> + >> + leds { >> + compatible = "gpio-leds"; >> + >> + power { >> + label = "orangepi:red:power"; >> + gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 >> */ >> + default-state = "on"; >> + }; >> + >> + status { >> + label = "orangepi:green:status"; >> + gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 >> */ >> + }; >> + }; >> + >> + reg_vcc5v: vcc5v { >> + /* board wide 5V supply directly from the USB-C socket >> */ >> + compatible = "regulator-fixed"; >> + regulator-name = "vcc-5v"; >> + regulator-min-microvolt = <5000000>; >> + regulator-max-microvolt = <5000000>; >> + regulator-always-on; >> + }; >> + >> + reg_usb1_vbus: usb1-vbus { >> + compatible = "regulator-fixed"; >> + regulator-name = "usb1-vbus"; >> + regulator-min-microvolt = <5000000>; >> + regulator-max-microvolt = <5000000>; >> + enable-active-high; >> + gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */ >> + status = "okay"; >> + }; >> +}; >> + >> +&ehci0 { >> + status = "okay"; >> +}; >> + >> +&ehci1 { >> + status = "okay"; >> +}; >> + >> +/* USB 2 & 3 are on headers only. */ >> + >> +&emac0 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&ext_rgmii_pins>; >> + phy-mode = "rgmii"; >> + phy-handle = <&ext_rgmii_phy>; >> + phy-supply = <®_dcdce>; >> + allwinner,rx-delay-ps = <3100>; >> + allwinner,tx-delay-ps = <700>; >> + status = "okay"; >> +}; >> + >> +&mdio { >> + ext_rgmii_phy: ethernet-phy@1 { >> + compatible = "ethernet-phy-ieee802.3-c22"; >> + reg = <1>; >> + }; >> +}; >> + >> +&mmc0 { >> + vmmc-supply = <®_dcdce>; >> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ >> + bus-width = <4>; >> + status = "okay"; >> +}; >> + >> +&ohci0 { >> + status = "okay"; >> +}; >> + >> +&ohci1 { >> + status = "okay"; >> +}; >> + >> +&r_i2c { >> + status = "okay"; >> + >> + axp305: pmic@36 { >> + compatible = "x-powers,axp305", "x-powers,axp805", >> + "x-powers,axp806"; >> + reg = <0x36>; >> + >> + /* dummy interrupt to appease the driver for now */ >> + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; >> + interrupt-controller; >> + #interrupt-cells = <1>; > > Is dummy interrupt future-proof? No, it's just a placeholder. The whole interrupt controller story isn't fully clear yet, the BSP DTS mentions one, but I didn't have time to investigate this yet. There is no NMI pad anymore, but an NMI IRQ number in this GIC table. The OPi Zero2 does not connect the AXP's IRQ pin to anything. I haven't checked the AXP driver yet, maybe it just needs to accept no interrupts? >> + >> + x-powers,self-working-mode; >> + vina-supply = <®_vcc5v>; >> + vinb-supply = <®_vcc5v>; >> + vinc-supply = <®_vcc5v>; >> + vind-supply = <®_vcc5v>; >> + vine-supply = <®_vcc5v>; >> + aldoin-supply = <®_vcc5v>; >> + bldoin-supply = <®_vcc5v>; >> + cldoin-supply = <®_vcc5v>; >> + >> + regulators { >> + reg_aldo1: aldo1 { >> + regulator-always-on; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + regulator-name = "vcc-sys"; >> + }; >> + >> + reg_aldo2: aldo2 { >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + regulator-name = "vcc3v3-ext"; >> + }; >> + >> + reg_aldo3: aldo3 { >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + regulator-name = "vcc3v3-ext2"; >> + }; >> + >> + reg_bldo1: bldo1 { >> + regulator-always-on; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-name = "vcc1v8"; >> + }; >> + >> + bldo2 { >> + /* unused */ >> + }; >> + >> + bldo3 { >> + /* unused */ >> + }; >> + >> + bldo4 { >> + /* unused */ >> + }; >> + >> + cldo1 { >> + /* reserved */ >> + }; >> + >> + cldo2 { >> + /* unused */ >> + }; >> + >> + cldo3 { >> + /* unused */ >> + }; >> + >> + reg_dcdca: dcdca { >> + regulator-always-on; >> + regulator-min-microvolt = <810000>; >> + regulator-max-microvolt = <1080000>; >> + regulator-name = "vdd-cpu"; >> + }; >> + >> + reg_dcdcc: dcdcc { >> + regulator-always-on; >> + regulator-min-microvolt = <810000>; >> + regulator-max-microvolt = <1080000>; >> + regulator-name = "vdd-gpu-sys"; >> + }; >> + >> + reg_dcdcd: dcdcd { >> + regulator-always-on; >> + regulator-min-microvolt = <1500000>; >> + regulator-max-microvolt = <1500000>; >> + regulator-name = "vdd-dram"; >> + }; >> + >> + reg_dcdce: dcdce { >> + regulator-boot-on; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + regulator-name = "vcc-eth-mmc"; >> + }; >> + >> + sw { >> + /* unused */ >> + }; >> + }; >> + }; >> +}; >> + >> +&uart0 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&uart0_ph_pins>; >> + status = "okay"; >> +}; >> + >> +&usbotg { >> + dr_mode = "otg"; > > The board is locked to a UFP due to fixed resistor on CC. OTG is not > possible. Ah, good point, I forgot to check this (not yet familiar with USB-C so much). Makes some sense, since this is the primary power connector as well. Cheers, Andre > >> + status = "okay"; >> +}; >> + >> +&usbphy { >> + usb0_vbus-supply = <®_vcc5v>; >> + usb1_vbus-supply = <®_usb1_vbus>; >> + status = "okay"; >> +};
Hi Andre, On Wed, 2 Dec 2020 at 14:54, Andre Przywara <andre.przywara@arm.com> wrote: > > The OrangePi Zero 2 is a development board with the new H616 SoC. > > It features the usual connectors used on those small boards, and comes > with the AXP305, which seems to be compatible with the AXP805. > > For more details see: http://linux-sunxi.org/Xunlong_Orange_Pi_Zero2 > > Signed-off-by: Andre Przywara <andre.przywara@arm.com> > --- > arch/arm64/boot/dts/allwinner/Makefile | 1 + > .../allwinner/sun50i-h616-orangepi-zero2.dts | 228 ++++++++++++++++++ > 2 files changed, 229 insertions(+) > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts > > diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile > index 211d1e9d4701..0cf8299b1ce7 100644 > --- a/arch/arm64/boot/dts/allwinner/Makefile > +++ b/arch/arm64/boot/dts/allwinner/Makefile > @@ -35,3 +35,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb > +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts > new file mode 100644 > index 000000000000..814f5b4fec7c > --- /dev/null > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts > @@ -0,0 +1,228 @@ > +// SPDX-License-Identifier: (GPL-2.0+ or MIT) > +/* > + * Copyright (C) 2020 Arm Ltd. > + */ > + > +/dts-v1/; > + > +#include "sun50i-h616.dtsi" > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/interrupt-controller/arm-gic.h> > + > +/ { > + model = "OrangePi Zero2"; > + compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616"; You need to add this compatible to the sunxi.yaml boards list > + > + aliases { > + ethernet0 = &emac0; > + serial0 = &uart0; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + power { > + label = "orangepi:red:power"; label is deprecated function = LED_FUNCTION_POWER; color = <LED_COLOR_ID_RED>; > + gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */ > + default-state = "on"; > + }; > + > + status { > + label = "orangepi:green:status"; same here function = LED_FUNCTION_STATUS; color = <LED_COLOR_ID_GREEN>; > + gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */ > + }; > + }; > + > + reg_vcc5v: vcc5v { > + /* board wide 5V supply directly from the USB-C socket */ > + compatible = "regulator-fixed"; > + regulator-name = "vcc-5v"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + }; > + > + reg_usb1_vbus: usb1-vbus { > + compatible = "regulator-fixed"; > + regulator-name = "usb1-vbus"; Could you add reg_vcc5v as vin-supply. This doesn't change anything but will be a better description of the HW. > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */ > + status = "okay"; > + }; > +}; > + > +&ehci0 { > + status = "okay"; > +}; > + > +&ehci1 { > + status = "okay"; > +}; > + > +/* USB 2 & 3 are on headers only. */ > + > +&emac0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&ext_rgmii_pins>; > + phy-mode = "rgmii"; > + phy-handle = <&ext_rgmii_phy>; > + phy-supply = <®_dcdce>; > + allwinner,rx-delay-ps = <3100>; > + allwinner,tx-delay-ps = <700>; > + status = "okay"; > +}; > + > +&mdio { > + ext_rgmii_phy: ethernet-phy@1 { > + compatible = "ethernet-phy-ieee802.3-c22"; > + reg = <1>; > + }; > +}; > + > +&mmc0 { > + vmmc-supply = <®_dcdce>; > + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ > + bus-width = <4>; > + status = "okay"; > +}; > + > +&ohci0 { > + status = "okay"; > +}; > + > +&ohci1 { > + status = "okay"; > +}; > + > +&r_i2c { > + status = "okay"; > + > + axp305: pmic@36 { > + compatible = "x-powers,axp305", "x-powers,axp805", > + "x-powers,axp806"; > + reg = <0x36>; > + > + /* dummy interrupt to appease the driver for now */ > + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-controller; > + #interrupt-cells = <1>; > + > + x-powers,self-working-mode; > + vina-supply = <®_vcc5v>; > + vinb-supply = <®_vcc5v>; > + vinc-supply = <®_vcc5v>; > + vind-supply = <®_vcc5v>; > + vine-supply = <®_vcc5v>; > + aldoin-supply = <®_vcc5v>; > + bldoin-supply = <®_vcc5v>; > + cldoin-supply = <®_vcc5v>; > + > + regulators { > + reg_aldo1: aldo1 { > + regulator-always-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc-sys"; > + }; > + > + reg_aldo2: aldo2 { > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc3v3-ext"; > + }; > + > + reg_aldo3: aldo3 { > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc3v3-ext2"; > + }; > + > + reg_bldo1: bldo1 { > + regulator-always-on; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcc1v8"; > + }; > + > + bldo2 { > + /* unused */ > + }; > + > + bldo3 { > + /* unused */ > + }; > + > + bldo4 { > + /* unused */ > + }; > + > + cldo1 { > + /* reserved */ > + }; > + > + cldo2 { > + /* unused */ > + }; > + > + cldo3 { > + /* unused */ > + }; > + > + reg_dcdca: dcdca { > + regulator-always-on; > + regulator-min-microvolt = <810000>; > + regulator-max-microvolt = <1080000>; > + regulator-name = "vdd-cpu"; > + }; > + > + reg_dcdcc: dcdcc { > + regulator-always-on; > + regulator-min-microvolt = <810000>; > + regulator-max-microvolt = <1080000>; > + regulator-name = "vdd-gpu-sys"; > + }; > + > + reg_dcdcd: dcdcd { > + regulator-always-on; > + regulator-min-microvolt = <1500000>; > + regulator-max-microvolt = <1500000>; > + regulator-name = "vdd-dram"; > + }; > + > + reg_dcdce: dcdce { > + regulator-boot-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc-eth-mmc"; > + }; > + > + sw { > + /* unused */ > + }; > + }; > + }; > +}; > + > +&uart0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart0_ph_pins>; > + status = "okay"; > +}; > + > +&usbotg { > + dr_mode = "otg"; > + status = "okay"; > +}; > + > +&usbphy { > + usb0_vbus-supply = <®_vcc5v>; > + usb1_vbus-supply = <®_usb1_vbus>; > + status = "okay"; > +}; > -- > 2.17.5 > > -- > You received this message because you are subscribed to the Google Groups "linux-sunxi" group. > To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@googlegroups.com. > To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20201202135409.13683-9-andre.przywara%40arm.com.
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile index 211d1e9d4701..0cf8299b1ce7 100644 --- a/arch/arm64/boot/dts/allwinner/Makefile +++ b/arch/arm64/boot/dts/allwinner/Makefile @@ -35,3 +35,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts new file mode 100644 index 000000000000..814f5b4fec7c --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts @@ -0,0 +1,228 @@ +// SPDX-License-Identifier: (GPL-2.0+ or MIT) +/* + * Copyright (C) 2020 Arm Ltd. + */ + +/dts-v1/; + +#include "sun50i-h616.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> + +/ { + model = "OrangePi Zero2"; + compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616"; + + aliases { + ethernet0 = &emac0; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + + power { + label = "orangepi:red:power"; + gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */ + default-state = "on"; + }; + + status { + label = "orangepi:green:status"; + gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */ + }; + }; + + reg_vcc5v: vcc5v { + /* board wide 5V supply directly from the USB-C socket */ + compatible = "regulator-fixed"; + regulator-name = "vcc-5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + reg_usb1_vbus: usb1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */ + status = "okay"; + }; +}; + +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +/* USB 2 & 3 are on headers only. */ + +&emac0 { + pinctrl-names = "default"; + pinctrl-0 = <&ext_rgmii_pins>; + phy-mode = "rgmii"; + phy-handle = <&ext_rgmii_phy>; + phy-supply = <®_dcdce>; + allwinner,rx-delay-ps = <3100>; + allwinner,tx-delay-ps = <700>; + status = "okay"; +}; + +&mdio { + ext_rgmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + +&mmc0 { + vmmc-supply = <®_dcdce>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ + bus-width = <4>; + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +&r_i2c { + status = "okay"; + + axp305: pmic@36 { + compatible = "x-powers,axp305", "x-powers,axp805", + "x-powers,axp806"; + reg = <0x36>; + + /* dummy interrupt to appease the driver for now */ + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + + x-powers,self-working-mode; + vina-supply = <®_vcc5v>; + vinb-supply = <®_vcc5v>; + vinc-supply = <®_vcc5v>; + vind-supply = <®_vcc5v>; + vine-supply = <®_vcc5v>; + aldoin-supply = <®_vcc5v>; + bldoin-supply = <®_vcc5v>; + cldoin-supply = <®_vcc5v>; + + regulators { + reg_aldo1: aldo1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-sys"; + }; + + reg_aldo2: aldo2 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc3v3-ext"; + }; + + reg_aldo3: aldo3 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc3v3-ext2"; + }; + + reg_bldo1: bldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc1v8"; + }; + + bldo2 { + /* unused */ + }; + + bldo3 { + /* unused */ + }; + + bldo4 { + /* unused */ + }; + + cldo1 { + /* reserved */ + }; + + cldo2 { + /* unused */ + }; + + cldo3 { + /* unused */ + }; + + reg_dcdca: dcdca { + regulator-always-on; + regulator-min-microvolt = <810000>; + regulator-max-microvolt = <1080000>; + regulator-name = "vdd-cpu"; + }; + + reg_dcdcc: dcdcc { + regulator-always-on; + regulator-min-microvolt = <810000>; + regulator-max-microvolt = <1080000>; + regulator-name = "vdd-gpu-sys"; + }; + + reg_dcdcd: dcdcd { + regulator-always-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-name = "vdd-dram"; + }; + + reg_dcdce: dcdce { + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-eth-mmc"; + }; + + sw { + /* unused */ + }; + }; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_ph_pins>; + status = "okay"; +}; + +&usbotg { + dr_mode = "otg"; + status = "okay"; +}; + +&usbphy { + usb0_vbus-supply = <®_vcc5v>; + usb1_vbus-supply = <®_usb1_vbus>; + status = "okay"; +};
The OrangePi Zero 2 is a development board with the new H616 SoC. It features the usual connectors used on those small boards, and comes with the AXP305, which seems to be compatible with the AXP805. For more details see: http://linux-sunxi.org/Xunlong_Orange_Pi_Zero2 Signed-off-by: Andre Przywara <andre.przywara@arm.com> --- arch/arm64/boot/dts/allwinner/Makefile | 1 + .../allwinner/sun50i-h616-orangepi-zero2.dts | 228 ++++++++++++++++++ 2 files changed, 229 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts