| Message ID | 20201125155113.192079-7-alexandru.elisei@arm.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | GIC fixes and improvements | expand |
Hi Alexandru, On 11/25/20 4:51 PM, Alexandru Elisei wrote: > The gicv{2,3}-active test sends an IPI from the boot CPU to itself, then > checks that the interrupt has been received as expected. The > ipi_clear_active_handler() clears the active state of the interrupt with a > write to the GICD_ICACTIVER register instead of writing the to EOI > register. > > When acknowledging the interrupt it is possible to get back an spurious > interrupt ID (ID 1023), and the interrupt handler increments the number of > spurious interrupts received on the current processor. However, this is not > checked at the end of the test. Let's also check for spurious interrupts, > like the IPI test does. > > For IPIs on GICv2, the value returned by a read of the GICC_IAR register > performed when acknowledging the interrupt also contains the sender CPU > ID. Add a check for that too. > > Signed-off-by: Alexandru Elisei <alexandru.elisei@arm.com> Reviewed-by: Eric Auger <eric.auger@redhat.com> Eric > --- > arm/gic.c | 8 +++++--- > 1 file changed, 5 insertions(+), 3 deletions(-) > > diff --git a/arm/gic.c b/arm/gic.c > index bcb834406d23..5727d72a0ef3 100644 > --- a/arm/gic.c > +++ b/arm/gic.c > @@ -125,12 +125,12 @@ static void check_spurious(void) > } > } > > -static void check_ipi_sender(u32 irqstat) > +static void check_ipi_sender(u32 irqstat, int sender) > { > if (gic_version() == 2) { > int src = (irqstat >> 10) & 7; > > - if (src != IPI_SENDER) > + if (src != sender) > bad_sender[smp_processor_id()] = src; > } > } > @@ -155,7 +155,7 @@ static void ipi_handler(struct pt_regs *regs __unused) > */ > if (gic_version() == 2) > smp_rmb(); > - check_ipi_sender(irqstat); > + check_ipi_sender(irqstat, IPI_SENDER); > check_irqnr(irqnr); > smp_wmb(); /* pairs with smp_rmb in check_acked */ > ++acked[smp_processor_id()]; > @@ -382,6 +382,7 @@ static void ipi_clear_active_handler(struct pt_regs *regs __unused) > > writel(val, base + GICD_ICACTIVER); > > + check_ipi_sender(irqstat, smp_processor_id()); > check_irqnr(irqnr); > ++acked[smp_processor_id()]; > } else { > @@ -394,6 +395,7 @@ static void run_active_clear_test(void) > report_prefix_push("active"); > setup_irq(ipi_clear_active_handler); > ipi_test_self(); > + check_spurious(); > report_prefix_pop(); > } > >
diff --git a/arm/gic.c b/arm/gic.c index bcb834406d23..5727d72a0ef3 100644 --- a/arm/gic.c +++ b/arm/gic.c @@ -125,12 +125,12 @@ static void check_spurious(void) } } -static void check_ipi_sender(u32 irqstat) +static void check_ipi_sender(u32 irqstat, int sender) { if (gic_version() == 2) { int src = (irqstat >> 10) & 7; - if (src != IPI_SENDER) + if (src != sender) bad_sender[smp_processor_id()] = src; } } @@ -155,7 +155,7 @@ static void ipi_handler(struct pt_regs *regs __unused) */ if (gic_version() == 2) smp_rmb(); - check_ipi_sender(irqstat); + check_ipi_sender(irqstat, IPI_SENDER); check_irqnr(irqnr); smp_wmb(); /* pairs with smp_rmb in check_acked */ ++acked[smp_processor_id()]; @@ -382,6 +382,7 @@ static void ipi_clear_active_handler(struct pt_regs *regs __unused) writel(val, base + GICD_ICACTIVER); + check_ipi_sender(irqstat, smp_processor_id()); check_irqnr(irqnr); ++acked[smp_processor_id()]; } else { @@ -394,6 +395,7 @@ static void run_active_clear_test(void) report_prefix_push("active"); setup_irq(ipi_clear_active_handler); ipi_test_self(); + check_spurious(); report_prefix_pop(); }
The gicv{2,3}-active test sends an IPI from the boot CPU to itself, then checks that the interrupt has been received as expected. The ipi_clear_active_handler() clears the active state of the interrupt with a write to the GICD_ICACTIVER register instead of writing the to EOI register. When acknowledging the interrupt it is possible to get back an spurious interrupt ID (ID 1023), and the interrupt handler increments the number of spurious interrupts received on the current processor. However, this is not checked at the end of the test. Let's also check for spurious interrupts, like the IPI test does. For IPIs on GICv2, the value returned by a read of the GICC_IAR register performed when acknowledging the interrupt also contains the sender CPU ID. Add a check for that too. Signed-off-by: Alexandru Elisei <alexandru.elisei@arm.com> --- arm/gic.c | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-)