diff mbox series

[v3,09/11] dt-bindings: usb: convert mediatek,mtk-xhci.txt to YAML schema

Message ID 20201118082126.42701-9-chunfeng.yun@mediatek.com (mailing list archive)
State Not Applicable
Delegated to: Netdev Maintainers
Headers show
Series [v3,01/11] dt-bindings: usb: convert usb-device.txt to YAML schema | expand

Checks

Context Check Description
netdev/tree_selection success Not a local patch

Commit Message

Chunfeng Yun (云春峰) Nov. 18, 2020, 8:21 a.m. UTC 
Convert mediatek,mtk-xhci.txt to YAML schema mediatek,mtk-xhci.yaml

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v3:
  1. fix yamllint warning
  2. remove pinctrl* properties supported by default suggested by Rob
  3. drop unused labels
  4. modify description of mediatek,syscon-wakeup
  5. remove type of imod-interval-ns

v2: new patch
---
 .../bindings/usb/mediatek,mtk-xhci.txt        | 121 -------------
 .../bindings/usb/mediatek,mtk-xhci.yaml       | 171 ++++++++++++++++++
 2 files changed, 171 insertions(+), 121 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt
 create mode 100644 Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml

Comments

Rob Herring Dec. 7, 2020, 9:24 p.m. UTC | #1 
On Wed, Nov 18, 2020 at 04:21:24PM +0800, Chunfeng Yun wrote:
> Convert mediatek,mtk-xhci.txt to YAML schema mediatek,mtk-xhci.yaml
> 
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
> v3:
>   1. fix yamllint warning
>   2. remove pinctrl* properties supported by default suggested by Rob
>   3. drop unused labels
>   4. modify description of mediatek,syscon-wakeup
>   5. remove type of imod-interval-ns
> 
> v2: new patch
> ---
>  .../bindings/usb/mediatek,mtk-xhci.txt        | 121 -------------
>  .../bindings/usb/mediatek,mtk-xhci.yaml       | 171 ++++++++++++++++++
>  2 files changed, 171 insertions(+), 121 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt
>  create mode 100644 Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
> 
> diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt
> deleted file mode 100644
> index 42d8814f903a..000000000000
> --- a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt
> +++ /dev/null
> @@ -1,121 +0,0 @@
> -MT8173 xHCI
> -
> -The device node for Mediatek SOC USB3.0 host controller
> -
> -There are two scenarios: the first one only supports xHCI driver;
> -the second one supports dual-role mode, and the host is based on xHCI
> -driver. Take account of backward compatibility, we divide bindings
> -into two parts.
> -
> -1st: only supports xHCI driver
> -------------------------------------------------------------------------
> -
> -Required properties:
> - - compatible : should be "mediatek,<soc-model>-xhci", "mediatek,mtk-xhci",
> -	soc-model is the name of SoC, such as mt8173, mt2712 etc, when using
> -	"mediatek,mtk-xhci" compatible string, you need SoC specific ones in
> -	addition, one of:
> -	- "mediatek,mt8173-xhci"
> - - reg : specifies physical base address and size of the registers
> - - reg-names: should be "mac" for xHCI MAC and "ippc" for IP port control
> - - interrupts : interrupt used by the controller
> - - power-domains : a phandle to USB power domain node to control USB's
> -	mtcmos
> - - vusb33-supply : regulator of USB avdd3.3v
> -
> - - clocks : a list of phandle + clock-specifier pairs, one for each
> -	entry in clock-names
> - - clock-names : must contain
> -	"sys_ck": controller clock used by normal mode,
> -	the following ones are optional:
> -	"ref_ck": reference clock used by low power mode etc,
> -	"mcu_ck": mcu_bus clock for register access,
> -	"dma_ck": dma_bus clock for data transfer by DMA,
> -	"xhci_ck": controller clock
> -
> - - phys : see usb-hcd.yaml in the current directory
> -
> -Optional properties:
> - - wakeup-source : enable USB remote wakeup;
> - - mediatek,syscon-wakeup : phandle to syscon used to access the register
> -	of the USB wakeup glue layer between xHCI and SPM; it depends on
> -	"wakeup-source", and has two arguments:
> -	- the first one : register base address of the glue layer in syscon;
> -	- the second one : hardware version of the glue layer
> -		- 1 : used by mt8173 etc
> -		- 2 : used by mt2712 etc
> - - mediatek,u3p-dis-msk : mask to disable u3ports, bit0 for u3port0,
> -	bit1 for u3port1, ... etc;
> - - vbus-supply : reference to the VBUS regulator;
> - - usb3-lpm-capable : supports USB3.0 LPM
> - - pinctrl-names : a pinctrl state named "default" must be defined
> - - pinctrl-0 : pin control group
> -	See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
> - - imod-interval-ns: default interrupt moderation interval is 5000ns
> -
> -additionally the properties from usb-hcd.yaml (in the current directory) are
> -supported.
> -
> -Example:
> -usb30: usb@11270000 {
> -	compatible = "mediatek,mt8173-xhci";
> -	reg = <0 0x11270000 0 0x1000>,
> -	      <0 0x11280700 0 0x0100>;
> -	reg-names = "mac", "ippc";
> -	interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
> -	power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
> -	clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>,
> -		 <&pericfg CLK_PERI_USB0>,
> -		 <&pericfg CLK_PERI_USB1>;
> -	clock-names = "sys_ck", "ref_ck";
> -	phys = <&phy_port0 PHY_TYPE_USB3>,
> -	       <&phy_port1 PHY_TYPE_USB2>;
> -	vusb33-supply = <&mt6397_vusb_reg>;
> -	vbus-supply = <&usb_p1_vbus>;
> -	usb3-lpm-capable;
> -	mediatek,syscon-wakeup = <&pericfg 0x400 1>;
> -	wakeup-source;
> -	imod-interval-ns = <10000>;
> -};
> -
> -2nd: dual-role mode with xHCI driver
> -------------------------------------------------------------------------
> -
> -In the case, xhci is added as subnode to mtu3. An example and the DT binding
> -details of mtu3 can be found in:
> -Documentation/devicetree/bindings/usb/mediatek,mtu3.txt
> -
> -Required properties:
> - - compatible : should be "mediatek,<soc-model>-xhci", "mediatek,mtk-xhci",
> -	soc-model is the name of SoC, such as mt8173, mt2712 etc, when using
> -	"mediatek,mtk-xhci" compatible string, you need SoC specific ones in
> -	addition, one of:
> -	- "mediatek,mt8173-xhci"
> - - reg : specifies physical base address and size of the registers
> - - reg-names: should be "mac" for xHCI MAC
> - - interrupts : interrupt used by the host controller
> - - power-domains : a phandle to USB power domain node to control USB's
> -	mtcmos
> - - vusb33-supply : regulator of USB avdd3.3v
> -
> - - clocks : a list of phandle + clock-specifier pairs, one for each
> -	entry in clock-names
> - - clock-names : must contain "sys_ck", and the following ones are optional:
> -	"ref_ck", "mcu_ck" and "dma_ck", "xhci_ck"
> -
> -Optional properties:
> - - vbus-supply : reference to the VBUS regulator;
> - - usb3-lpm-capable : supports USB3.0 LPM
> -
> -Example:
> -usb30: usb@11270000 {
> -	compatible = "mediatek,mt8173-xhci";
> -	reg = <0 0x11270000 0 0x1000>;
> -	reg-names = "mac";
> -	interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
> -	power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
> -	clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>;
> -	clock-names = "sys_ck", "ref_ck";
> -	vusb33-supply = <&mt6397_vusb_reg>;
> -	usb3-lpm-capable;
> -};
> diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
> new file mode 100644
> index 000000000000..4a36ad5c4d25
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
> @@ -0,0 +1,171 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +# Copyright (c) 2020 MediaTek
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/usb/mediatek,mtk-xhci.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: MediaTek USB3 xHCI Device Tree Bindings
> +
> +maintainers:
> +  - Chunfeng Yun <chunfeng.yun@mediatek.com>
> +
> +allOf:
> +  - $ref: "usb-hcd.yaml"
> +
> +description: |
> +  There are two scenarios:
> +  case 1: only supports xHCI driver;
> +  case 2: supports dual-role mode, and the host is based on xHCI driver.
> +
> +properties:
> +  # common properties for both case 1 and case 2
> +  compatible:
> +    items:
> +      - enum:
> +          - mediatek,mt2712-xhci
> +          - mediatek,mt7622-xhci
> +          - mediatek,mt7629-xhci
> +          - mediatek,mt8173-xhci
> +          - mediatek,mt8183-xhci
> +      - const: mediatek,mtk-xhci
> +
> +  reg:
> +    minItems: 1
> +    maxItems: 2
> +    items:
> +      - description: the registers of xHCI MAC
> +      - description: the registers of IP Port Control
> +
> +  reg-names:
> +    minItems: 1
> +    maxItems: 2
> +    items:
> +      - const: mac
> +      - const: ippc  # optional, only needed for case 1.
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  power-domains:
> +    description: A phandle to USB power domain node to control USB's MTCMOS
> +    maxItems: 1
> +
> +  clocks:
> +    minItems: 1
> +    maxItems: 5
> +    items:
> +      - description: Controller clock used by normal mode
> +      - description: Reference clock used by low power mode etc
> +      - description: Mcu bus clock for register access
> +      - description: DMA bus clock for data transfer
> +      - description: controller clock
> +
> +  clock-names:
> +    minItems: 1
> +    maxItems: 5
> +    items:
> +      - const: sys_ck  # required, the following ones are optional
> +      - const: ref_ck
> +      - const: mcu_ck
> +      - const: dma_ck
> +      - const: xhci_ck
> +
> +  phys:
> +    $ref: /usb/usb-hcd.yaml#

That's not right.

You need 'items' and list each entry.

> +    description: List of all the USB PHYs on this HCD
> +
> +  vusb33-supply:
> +    description: Regulator of USB AVDD3.3v
> +
> +  vbus-supply:
> +    description: Regulator of USB VBUS5v
> +
> +  usb3-lpm-capable:
> +    description: supports USB3.0 LPM
> +    type: boolean
> +
> +  imod-interval-ns:
> +    description:
> +      Interrupt moderation interval value, it is 8 times as much as that
> +      defined in the xHCI spec on MTK's controller.
> +    default: 5000
> +
> +  # the following properties are only used for case 1
> +  wakeup-source:
> +    description: enable USB remote wakeup, see power/wakeup-source.txt
> +    type: boolean
> +
> +  mediatek,syscon-wakeup:
> +    $ref: /schemas/types.yaml#/definitions/phandle-array
> +    maxItems: 1
> +    description: |
> +      A phandle to syscon used to access the register of the USB wakeup glue
> +      layer between xHCI and SPM, the field should always be 3 cells long.
> +
> +      items:

Indentation is wrong here. Should be 2 fewer spaces.

> +        - description:
> +            The first cell represents a phandle to syscon
> +        - description:
> +            The second cell represents the register base address of the glue
> +            layer in syscon
> +        - description:
> +            The third cell represents the hardware version of the glue layer,
> +            1 is used by mt8173 etc, 2 is used by mt2712 etc
> +          enum: [1, 2]
> +
> +  mediatek,u3p-dis-msk:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    description: The mask to disable u3ports, bit0 for u3port0,
> +      bit1 for u3port1, ... etc
> +
> +  "#address-cells":
> +    const: 1
> +
> +  "#size-cells":
> +    const: 0
> +
> +patternProperties:
> +  "^[a-f]+@[0-9a-f]+$":
> +    $ref: /usb/usb-hcd.yaml#

This $ref isn't right. You already referenced it at the top.

> +    type: object
> +    description: The hard wired USB devices.
> +
> +dependencies:
> +  wakeup-source: [ 'mediatek,syscon-wakeup' ]
> +
> +required:
> +  - compatible
> +  - reg
> +  - reg-names
> +  - interrupts
> +  - clocks
> +  - clock-names
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/clock/mt8173-clk.h>
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +    #include <dt-bindings/phy/phy.h>
> +    #include <dt-bindings/power/mt8173-power.h>
> +
> +    usb@11270000 {
> +        compatible = "mediatek,mt8173-xhci", "mediatek,mtk-xhci";
> +        reg = <0x11270000 0x1000>, <0x11280700 0x0100>;
> +        reg-names = "mac", "ippc";
> +        interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
> +        power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
> +        clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>;
> +        clock-names = "sys_ck", "ref_ck";
> +        phys = <&u3port0 PHY_TYPE_USB3>, <&u2port1 PHY_TYPE_USB2>;
> +        vusb33-supply = <&mt6397_vusb_reg>;
> +        vbus-supply = <&usb_p1_vbus>;
> +        imod-interval-ns = <10000>;
> +        mediatek,syscon-wakeup = <&pericfg 0x400 1>;
> +        wakeup-source;
> +        usb3-lpm-capable;
> +    };
> +...
> -- 
> 2.18.0
>
Chunfeng Yun (云春峰) Dec. 8, 2020, 9:11 a.m. UTC | #2 
On Mon, 2020-12-07 at 15:24 -0600, Rob Herring wrote:
> On Wed, Nov 18, 2020 at 04:21:24PM +0800, Chunfeng Yun wrote:
> > Convert mediatek,mtk-xhci.txt to YAML schema mediatek,mtk-xhci.yaml
> > 
> > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> > ---
> > v3:
> >   1. fix yamllint warning
> >   2. remove pinctrl* properties supported by default suggested by Rob
> >   3. drop unused labels
> >   4. modify description of mediatek,syscon-wakeup
> >   5. remove type of imod-interval-ns
> > 
> > v2: new patch
> > ---
> >  .../bindings/usb/mediatek,mtk-xhci.txt        | 121 -------------
> >  .../bindings/usb/mediatek,mtk-xhci.yaml       | 171 ++++++++++++++++++
> >  2 files changed, 171 insertions(+), 121 deletions(-)
> >  delete mode 100644 Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt
> >  create mode 100644 Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
[...]
> > diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
> > new file mode 100644
> > index 000000000000..4a36ad5c4d25
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
> > @@ -0,0 +1,171 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +# Copyright (c) 2020 MediaTek
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/usb/mediatek,mtk-xhci.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: MediaTek USB3 xHCI Device Tree Bindings
> > +
> > +maintainers:
> > +  - Chunfeng Yun <chunfeng.yun@mediatek.com>
> > +
> > +allOf:
> > +  - $ref: "usb-hcd.yaml"
> > +
> > +description: |
> > +  There are two scenarios:
> > +  case 1: only supports xHCI driver;
> > +  case 2: supports dual-role mode, and the host is based on xHCI driver.
> > +
> > +properties:
> > +  # common properties for both case 1 and case 2
> > +  compatible:
> > +    items:
> > +      - enum:
> > +          - mediatek,mt2712-xhci
> > +          - mediatek,mt7622-xhci
> > +          - mediatek,mt7629-xhci
> > +          - mediatek,mt8173-xhci
> > +          - mediatek,mt8183-xhci
> > +      - const: mediatek,mtk-xhci
> > +
> > +  reg:
> > +    minItems: 1
> > +    maxItems: 2
> > +    items:
> > +      - description: the registers of xHCI MAC
> > +      - description: the registers of IP Port Control
> > +
> > +  reg-names:
> > +    minItems: 1
> > +    maxItems: 2
> > +    items:
> > +      - const: mac
> > +      - const: ippc  # optional, only needed for case 1.
> > +
> > +  interrupts:
> > +    maxItems: 1
> > +
> > +  power-domains:
> > +    description: A phandle to USB power domain node to control USB's MTCMOS
> > +    maxItems: 1
> > +
> > +  clocks:
> > +    minItems: 1
> > +    maxItems: 5
> > +    items:
> > +      - description: Controller clock used by normal mode
> > +      - description: Reference clock used by low power mode etc
> > +      - description: Mcu bus clock for register access
> > +      - description: DMA bus clock for data transfer
> > +      - description: controller clock
> > +
> > +  clock-names:
> > +    minItems: 1
> > +    maxItems: 5
> > +    items:
> > +      - const: sys_ck  # required, the following ones are optional
> > +      - const: ref_ck
> > +      - const: mcu_ck
> > +      - const: dma_ck
> > +      - const: xhci_ck
> > +
> > +  phys:
> > +    $ref: /usb/usb-hcd.yaml#
> 
> That's not right.
> 
> You need 'items' and list each entry.
Will add minItems/maxItems instead due to it's variable and phy-names is
not used

> 
> > +    description: List of all the USB PHYs on this HCD
> > +
> > +  vusb33-supply:
> > +    description: Regulator of USB AVDD3.3v
> > +
> > +  vbus-supply:
> > +    description: Regulator of USB VBUS5v
> > +
> > +  usb3-lpm-capable:
> > +    description: supports USB3.0 LPM
> > +    type: boolean
> > +
> > +  imod-interval-ns:
> > +    description:
> > +      Interrupt moderation interval value, it is 8 times as much as that
> > +      defined in the xHCI spec on MTK's controller.
> > +    default: 5000
> > +
> > +  # the following properties are only used for case 1
> > +  wakeup-source:
> > +    description: enable USB remote wakeup, see power/wakeup-source.txt
> > +    type: boolean
> > +
> > +  mediatek,syscon-wakeup:
> > +    $ref: /schemas/types.yaml#/definitions/phandle-array
> > +    maxItems: 1
> > +    description: |
> > +      A phandle to syscon used to access the register of the USB wakeup glue
> > +      layer between xHCI and SPM, the field should always be 3 cells long.
> > +
> > +      items:
> 
> Indentation is wrong here. Should be 2 fewer spaces.
Will fix it
> 
> > +        - description:
> > +            The first cell represents a phandle to syscon
> > +        - description:
> > +            The second cell represents the register base address of the glue
> > +            layer in syscon
> > +        - description:
> > +            The third cell represents the hardware version of the glue layer,
> > +            1 is used by mt8173 etc, 2 is used by mt2712 etc
> > +          enum: [1, 2]
> > +
> > +  mediatek,u3p-dis-msk:
> > +    $ref: /schemas/types.yaml#/definitions/uint32
> > +    description: The mask to disable u3ports, bit0 for u3port0,
> > +      bit1 for u3port1, ... etc
> > +
> > +  "#address-cells":
> > +    const: 1
> > +
> > +  "#size-cells":
> > +    const: 0
> > +
> > +patternProperties:
> > +  "^[a-f]+@[0-9a-f]+$":
> > +    $ref: /usb/usb-hcd.yaml#
> 
> This $ref isn't right. You already referenced it at the top.
Will drop it

Thank you

> 
> > +    type: object
> > +    description: The hard wired USB devices.
> > +
> > +dependencies:
> > +  wakeup-source: [ 'mediatek,syscon-wakeup' ]
> > +
> > +required:
> > +  - compatible
> > +  - reg
> > +  - reg-names
> > +  - interrupts
> > +  - clocks
> > +  - clock-names
> > +
> > +additionalProperties: false
> > +
> > +examples:
> > +  - |
> > +    #include <dt-bindings/clock/mt8173-clk.h>
> > +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> > +    #include <dt-bindings/interrupt-controller/irq.h>
> > +    #include <dt-bindings/phy/phy.h>
> > +    #include <dt-bindings/power/mt8173-power.h>
> > +
> > +    usb@11270000 {
> > +        compatible = "mediatek,mt8173-xhci", "mediatek,mtk-xhci";
> > +        reg = <0x11270000 0x1000>, <0x11280700 0x0100>;
> > +        reg-names = "mac", "ippc";
> > +        interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
> > +        power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
> > +        clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>;
> > +        clock-names = "sys_ck", "ref_ck";
> > +        phys = <&u3port0 PHY_TYPE_USB3>, <&u2port1 PHY_TYPE_USB2>;
> > +        vusb33-supply = <&mt6397_vusb_reg>;
> > +        vbus-supply = <&usb_p1_vbus>;
> > +        imod-interval-ns = <10000>;
> > +        mediatek,syscon-wakeup = <&pericfg 0x400 1>;
> > +        wakeup-source;
> > +        usb3-lpm-capable;
> > +    };
> > +...
> > -- 
> > 2.18.0
> >
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt
deleted file mode 100644
index 42d8814f903a..000000000000
--- a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt
+++ /dev/null
@@ -1,121 +0,0 @@ 
-MT8173 xHCI
-
-The device node for Mediatek SOC USB3.0 host controller
-
-There are two scenarios: the first one only supports xHCI driver;
-the second one supports dual-role mode, and the host is based on xHCI
-driver. Take account of backward compatibility, we divide bindings
-into two parts.
-
-1st: only supports xHCI driver
-------------------------------------------------------------------------
-
-Required properties:
- - compatible : should be "mediatek,<soc-model>-xhci", "mediatek,mtk-xhci",
-	soc-model is the name of SoC, such as mt8173, mt2712 etc, when using
-	"mediatek,mtk-xhci" compatible string, you need SoC specific ones in
-	addition, one of:
-	- "mediatek,mt8173-xhci"
- - reg : specifies physical base address and size of the registers
- - reg-names: should be "mac" for xHCI MAC and "ippc" for IP port control
- - interrupts : interrupt used by the controller
- - power-domains : a phandle to USB power domain node to control USB's
-	mtcmos
- - vusb33-supply : regulator of USB avdd3.3v
-
- - clocks : a list of phandle + clock-specifier pairs, one for each
-	entry in clock-names
- - clock-names : must contain
-	"sys_ck": controller clock used by normal mode,
-	the following ones are optional:
-	"ref_ck": reference clock used by low power mode etc,
-	"mcu_ck": mcu_bus clock for register access,
-	"dma_ck": dma_bus clock for data transfer by DMA,
-	"xhci_ck": controller clock
-
- - phys : see usb-hcd.yaml in the current directory
-
-Optional properties:
- - wakeup-source : enable USB remote wakeup;
- - mediatek,syscon-wakeup : phandle to syscon used to access the register
-	of the USB wakeup glue layer between xHCI and SPM; it depends on
-	"wakeup-source", and has two arguments:
-	- the first one : register base address of the glue layer in syscon;
-	- the second one : hardware version of the glue layer
-		- 1 : used by mt8173 etc
-		- 2 : used by mt2712 etc
- - mediatek,u3p-dis-msk : mask to disable u3ports, bit0 for u3port0,
-	bit1 for u3port1, ... etc;
- - vbus-supply : reference to the VBUS regulator;
- - usb3-lpm-capable : supports USB3.0 LPM
- - pinctrl-names : a pinctrl state named "default" must be defined
- - pinctrl-0 : pin control group
-	See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
- - imod-interval-ns: default interrupt moderation interval is 5000ns
-
-additionally the properties from usb-hcd.yaml (in the current directory) are
-supported.
-
-Example:
-usb30: usb@11270000 {
-	compatible = "mediatek,mt8173-xhci";
-	reg = <0 0x11270000 0 0x1000>,
-	      <0 0x11280700 0 0x0100>;
-	reg-names = "mac", "ippc";
-	interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
-	power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
-	clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>,
-		 <&pericfg CLK_PERI_USB0>,
-		 <&pericfg CLK_PERI_USB1>;
-	clock-names = "sys_ck", "ref_ck";
-	phys = <&phy_port0 PHY_TYPE_USB3>,
-	       <&phy_port1 PHY_TYPE_USB2>;
-	vusb33-supply = <&mt6397_vusb_reg>;
-	vbus-supply = <&usb_p1_vbus>;
-	usb3-lpm-capable;
-	mediatek,syscon-wakeup = <&pericfg 0x400 1>;
-	wakeup-source;
-	imod-interval-ns = <10000>;
-};
-
-2nd: dual-role mode with xHCI driver
-------------------------------------------------------------------------
-
-In the case, xhci is added as subnode to mtu3. An example and the DT binding
-details of mtu3 can be found in:
-Documentation/devicetree/bindings/usb/mediatek,mtu3.txt
-
-Required properties:
- - compatible : should be "mediatek,<soc-model>-xhci", "mediatek,mtk-xhci",
-	soc-model is the name of SoC, such as mt8173, mt2712 etc, when using
-	"mediatek,mtk-xhci" compatible string, you need SoC specific ones in
-	addition, one of:
-	- "mediatek,mt8173-xhci"
- - reg : specifies physical base address and size of the registers
- - reg-names: should be "mac" for xHCI MAC
- - interrupts : interrupt used by the host controller
- - power-domains : a phandle to USB power domain node to control USB's
-	mtcmos
- - vusb33-supply : regulator of USB avdd3.3v
-
- - clocks : a list of phandle + clock-specifier pairs, one for each
-	entry in clock-names
- - clock-names : must contain "sys_ck", and the following ones are optional:
-	"ref_ck", "mcu_ck" and "dma_ck", "xhci_ck"
-
-Optional properties:
- - vbus-supply : reference to the VBUS regulator;
- - usb3-lpm-capable : supports USB3.0 LPM
-
-Example:
-usb30: usb@11270000 {
-	compatible = "mediatek,mt8173-xhci";
-	reg = <0 0x11270000 0 0x1000>;
-	reg-names = "mac";
-	interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
-	power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
-	clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>;
-	clock-names = "sys_ck", "ref_ck";
-	vusb33-supply = <&mt6397_vusb_reg>;
-	usb3-lpm-capable;
-};
diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
new file mode 100644
index 000000000000..4a36ad5c4d25
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
@@ -0,0 +1,171 @@ 
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (c) 2020 MediaTek
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/usb/mediatek,mtk-xhci.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek USB3 xHCI Device Tree Bindings
+
+maintainers:
+  - Chunfeng Yun <chunfeng.yun@mediatek.com>
+
+allOf:
+  - $ref: "usb-hcd.yaml"
+
+description: |
+  There are two scenarios:
+  case 1: only supports xHCI driver;
+  case 2: supports dual-role mode, and the host is based on xHCI driver.
+
+properties:
+  # common properties for both case 1 and case 2
+  compatible:
+    items:
+      - enum:
+          - mediatek,mt2712-xhci
+          - mediatek,mt7622-xhci
+          - mediatek,mt7629-xhci
+          - mediatek,mt8173-xhci
+          - mediatek,mt8183-xhci
+      - const: mediatek,mtk-xhci
+
+  reg:
+    minItems: 1
+    maxItems: 2
+    items:
+      - description: the registers of xHCI MAC
+      - description: the registers of IP Port Control
+
+  reg-names:
+    minItems: 1
+    maxItems: 2
+    items:
+      - const: mac
+      - const: ippc  # optional, only needed for case 1.
+
+  interrupts:
+    maxItems: 1
+
+  power-domains:
+    description: A phandle to USB power domain node to control USB's MTCMOS
+    maxItems: 1
+
+  clocks:
+    minItems: 1
+    maxItems: 5
+    items:
+      - description: Controller clock used by normal mode
+      - description: Reference clock used by low power mode etc
+      - description: Mcu bus clock for register access
+      - description: DMA bus clock for data transfer
+      - description: controller clock
+
+  clock-names:
+    minItems: 1
+    maxItems: 5
+    items:
+      - const: sys_ck  # required, the following ones are optional
+      - const: ref_ck
+      - const: mcu_ck
+      - const: dma_ck
+      - const: xhci_ck
+
+  phys:
+    $ref: /usb/usb-hcd.yaml#
+    description: List of all the USB PHYs on this HCD
+
+  vusb33-supply:
+    description: Regulator of USB AVDD3.3v
+
+  vbus-supply:
+    description: Regulator of USB VBUS5v
+
+  usb3-lpm-capable:
+    description: supports USB3.0 LPM
+    type: boolean
+
+  imod-interval-ns:
+    description:
+      Interrupt moderation interval value, it is 8 times as much as that
+      defined in the xHCI spec on MTK's controller.
+    default: 5000
+
+  # the following properties are only used for case 1
+  wakeup-source:
+    description: enable USB remote wakeup, see power/wakeup-source.txt
+    type: boolean
+
+  mediatek,syscon-wakeup:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    maxItems: 1
+    description: |
+      A phandle to syscon used to access the register of the USB wakeup glue
+      layer between xHCI and SPM, the field should always be 3 cells long.
+
+      items:
+        - description:
+            The first cell represents a phandle to syscon
+        - description:
+            The second cell represents the register base address of the glue
+            layer in syscon
+        - description:
+            The third cell represents the hardware version of the glue layer,
+            1 is used by mt8173 etc, 2 is used by mt2712 etc
+          enum: [1, 2]
+
+  mediatek,u3p-dis-msk:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: The mask to disable u3ports, bit0 for u3port0,
+      bit1 for u3port1, ... etc
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+patternProperties:
+  "^[a-f]+@[0-9a-f]+$":
+    $ref: /usb/usb-hcd.yaml#
+    type: object
+    description: The hard wired USB devices.
+
+dependencies:
+  wakeup-source: [ 'mediatek,syscon-wakeup' ]
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - interrupts
+  - clocks
+  - clock-names
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/mt8173-clk.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/phy/phy.h>
+    #include <dt-bindings/power/mt8173-power.h>
+
+    usb@11270000 {
+        compatible = "mediatek,mt8173-xhci", "mediatek,mtk-xhci";
+        reg = <0x11270000 0x1000>, <0x11280700 0x0100>;
+        reg-names = "mac", "ippc";
+        interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
+        power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
+        clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>;
+        clock-names = "sys_ck", "ref_ck";
+        phys = <&u3port0 PHY_TYPE_USB3>, <&u2port1 PHY_TYPE_USB2>;
+        vusb33-supply = <&mt6397_vusb_reg>;
+        vbus-supply = <&usb_p1_vbus>;
+        imod-interval-ns = <10000>;
+        mediatek,syscon-wakeup = <&pericfg 0x400 1>;
+        wakeup-source;
+        usb3-lpm-capable;
+    };
+...