| Message ID | 87lfdpndkt.fsf@intel.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [PULL] topic/dp-hdmi-2.1-pcon for drm-misc-next | expand |
On Wed, Dec 23, 2020 at 10:14:58AM +0200, Jani Nikula wrote: > > Hi Maarten, Maxime, and Thomas - > > Here's the DP-HDMI2.1 PCON support topic pull consisting of the series > [1]. The series is split roughly 50-50 between drm helpers and i915, so > a topic branch seemed to be the right way to go. > > I'll also pull this to drm-intel-next once you've merged to > drm-misc-next. I didn't see this merged into drm-misc-next, so pulled into drm-next. I'm processing an entire batch of pulls, I'll ping you on irc when it's all ready for backmerging. Cheers, Daniel > > BR, > Jani. > > > [1] https://patchwork.freedesktop.org/series/82098/ > > > topic/dp-hdmi-2.1-pcon-2020-12-23: > Add support for DP-HDMI2.1 PCON > > From the series cover letter: > > This patch series attempts to add support for a DP-HDMI2.1 Protocol > Convertor. The VESA spec for the HDMI2.1 PCON are proposed in Errata > E5 to DisplayPort_v2.0: > https://vesa.org/join-vesamemberships/member-downloads/?action=stamp&fileid=42299 > The details are mentioned in: > VESA DP-to-HDMI PCON Specification Standalone Document > https://groups.vesa.org/wg/DP/document/15651 > > This series starts with adding support for FRL (Fixed Rate Link) > Training between the PCON and HDMI2.1 sink. > As per HDMI2.1 specification, a new data-channel or lane is added in > FRL mode, by repurposing the TMDS clock Channel. Through FRL, higher > bit-rate can be supported, ie. up to 12 Gbps/lane (48 Gbps over 4 > lanes). > > With these patches, the HDMI2.1 PCON can be configured to achieve FRL > training based on the maximum FRL rate supported by the panel, source > and the PCON. > The approach is to add the support for FRL training between PCON and > HDMI2.1 sink and gradually add other blocks for supporting higher > resolutions and other HDMI2.1 features, that can be supported by pcon > for the sources that do not natively support HDMI2.1. > > This is done before the DP Link training between the source and PCON > is started. In case of FRL training is not achieved, the PCON will > work in the regular TMDS mode, without HDMI2.1 feature support. > Any interruption in FRL training between the PCON and HDMI2.1 sink is > notified through IRQ_HPD. On receiving the IRQ_HPD the concerned DPCD > registers are read and FRL training is re-attempted. > > Currently, we have tested the FRL training and are able to enable 4K > display with TGL Platform + Realtek PCON RTD2173 with HDMI2.1 supporting > panel. > > The following changes since commit b3bf99daaee96a141536ce5c60a0d6dba6ec1d23: > > drm/i915/display: Defer initial modeset until after GGTT is initialised (2020-11-26 11:01:52 +0000) > > are available in the Git repository at: > > git://anongit.freedesktop.org/drm/drm-intel tags/topic/dp-hdmi-2.1-pcon-2020-12-23 > > for you to fetch changes up to 522508b665df3bbfdf40381d4e61777844b1703f: > > drm/i915/display: Let PCON convert from RGB to YCbCr if it can (2020-12-22 17:59:07 +0200) > > ---------------------------------------------------------------- > Add support for DP-HDMI2.1 PCON > > From the series cover letter: > > This patch series attempts to add support for a DP-HDMI2.1 Protocol > Convertor. The VESA spec for the HDMI2.1 PCON are proposed in Errata > E5 to DisplayPort_v2.0: > https://vesa.org/join-vesamemberships/member-downloads/?action=stamp&fileid=42299 > The details are mentioned in: > VESA DP-to-HDMI PCON Specification Standalone Document > https://groups.vesa.org/wg/DP/document/15651 > > This series starts with adding support for FRL (Fixed Rate Link) > Training between the PCON and HDMI2.1 sink. > As per HDMI2.1 specification, a new data-channel or lane is added in > FRL mode, by repurposing the TMDS clock Channel. Through FRL, higher > bit-rate can be supported, ie. up to 12 Gbps/lane (48 Gbps over 4 > lanes). > > With these patches, the HDMI2.1 PCON can be configured to achieve FRL > training based on the maximum FRL rate supported by the panel, source > and the PCON. > The approach is to add the support for FRL training between PCON and > HDMI2.1 sink and gradually add other blocks for supporting higher > resolutions and other HDMI2.1 features, that can be supported by pcon > for the sources that do not natively support HDMI2.1. > > This is done before the DP Link training between the source and PCON > is started. In case of FRL training is not achieved, the PCON will > work in the regular TMDS mode, without HDMI2.1 feature support. > Any interruption in FRL training between the PCON and HDMI2.1 sink is > notified through IRQ_HPD. On receiving the IRQ_HPD the concerned DPCD > registers are read and FRL training is re-attempted. > > Currently, we have tested the FRL training and are able to enable 4K > display with TGL Platform + Realtek PCON RTD2173 with HDMI2.1 supporting > panel. > > ---------------------------------------------------------------- > Ankit Nautiyal (11): > drm/edid: Parse DSC1.2 cap fields from HFVSDB block > drm/dp_helper: Add Helpers for FRL Link Training support for DP-HDMI2.1 PCON > drm/dp_helper: Add support for Configuring DSC for HDMI2.1 Pcon > drm/dp_helper: Add helpers to configure PCONs RGB-YCbCr Conversion > drm/i915: Capture max frl rate for PCON in dfp cap structure > drm/i915: Add support for starting FRL training for HDMI2.1 via PCON > drm/i915: Check for FRL training before DP Link training > drm/i915: Read DSC capabilities of the HDMI2.1 PCON encoder > drm/i915: Add helper functions for calculating DSC parameters for HDMI2.1 > drm/i915/display: Configure PCON for DSC1.1 to DSC1.2 encoding > drm/i915/display: Let PCON convert from RGB to YCbCr if it can > > Swati Sharma (4): > drm/edid: Add additional HFVSDB fields for HDMI2.1 > drm/edid: Parse MAX_FRL field from HFVSDB block > drm/dp_helper: Add support for link failure detection > drm/i915: Add support for enabling link status and recovery > > drivers/gpu/drm/drm_dp_helper.c | 566 +++++++++++++++++++++ > drivers/gpu/drm/drm_edid.c | 103 ++++ > drivers/gpu/drm/i915/display/intel_ddi.c | 6 +- > drivers/gpu/drm/i915/display/intel_display_types.h | 10 + > drivers/gpu/drm/i915/display/intel_dp.c | 440 +++++++++++++++- > drivers/gpu/drm/i915/display/intel_dp.h | 7 +- > drivers/gpu/drm/i915/display/intel_hdmi.c | 233 +++++++++ > drivers/gpu/drm/i915/display/intel_hdmi.h | 7 + > include/drm/drm_connector.h | 49 ++ > include/drm/drm_dp_helper.h | 218 ++++++++ > include/drm/drm_edid.h | 30 ++ > 11 files changed, 1650 insertions(+), 19 deletions(-) > > -- > Jani Nikula, Intel Open Source Graphics Center
On Thu, 07 Jan 2021, Daniel Vetter <daniel@ffwll.ch> wrote: > On Wed, Dec 23, 2020 at 10:14:58AM +0200, Jani Nikula wrote: >> >> Hi Maarten, Maxime, and Thomas - >> >> Here's the DP-HDMI2.1 PCON support topic pull consisting of the series >> [1]. The series is split roughly 50-50 between drm helpers and i915, so >> a topic branch seemed to be the right way to go. >> >> I'll also pull this to drm-intel-next once you've merged to >> drm-misc-next. > > I didn't see this merged into drm-misc-next, so pulled into drm-next. I'm > processing an entire batch of pulls, I'll ping you on irc when it's all > ready for backmerging. Thanks, Rodrigo covered the backmerge. BR, Jani. > > Cheers, Daniel > >> >> BR, >> Jani. >> >> >> [1] https://patchwork.freedesktop.org/series/82098/ >> >> >> topic/dp-hdmi-2.1-pcon-2020-12-23: >> Add support for DP-HDMI2.1 PCON >> >> From the series cover letter: >> >> This patch series attempts to add support for a DP-HDMI2.1 Protocol >> Convertor. The VESA spec for the HDMI2.1 PCON are proposed in Errata >> E5 to DisplayPort_v2.0: >> https://vesa.org/join-vesamemberships/member-downloads/?action=stamp&fileid=42299 >> The details are mentioned in: >> VESA DP-to-HDMI PCON Specification Standalone Document >> https://groups.vesa.org/wg/DP/document/15651 >> >> This series starts with adding support for FRL (Fixed Rate Link) >> Training between the PCON and HDMI2.1 sink. >> As per HDMI2.1 specification, a new data-channel or lane is added in >> FRL mode, by repurposing the TMDS clock Channel. Through FRL, higher >> bit-rate can be supported, ie. up to 12 Gbps/lane (48 Gbps over 4 >> lanes). >> >> With these patches, the HDMI2.1 PCON can be configured to achieve FRL >> training based on the maximum FRL rate supported by the panel, source >> and the PCON. >> The approach is to add the support for FRL training between PCON and >> HDMI2.1 sink and gradually add other blocks for supporting higher >> resolutions and other HDMI2.1 features, that can be supported by pcon >> for the sources that do not natively support HDMI2.1. >> >> This is done before the DP Link training between the source and PCON >> is started. In case of FRL training is not achieved, the PCON will >> work in the regular TMDS mode, without HDMI2.1 feature support. >> Any interruption in FRL training between the PCON and HDMI2.1 sink is >> notified through IRQ_HPD. On receiving the IRQ_HPD the concerned DPCD >> registers are read and FRL training is re-attempted. >> >> Currently, we have tested the FRL training and are able to enable 4K >> display with TGL Platform + Realtek PCON RTD2173 with HDMI2.1 supporting >> panel. >> >> The following changes since commit b3bf99daaee96a141536ce5c60a0d6dba6ec1d23: >> >> drm/i915/display: Defer initial modeset until after GGTT is initialised (2020-11-26 11:01:52 +0000) >> >> are available in the Git repository at: >> >> git://anongit.freedesktop.org/drm/drm-intel tags/topic/dp-hdmi-2.1-pcon-2020-12-23 >> >> for you to fetch changes up to 522508b665df3bbfdf40381d4e61777844b1703f: >> >> drm/i915/display: Let PCON convert from RGB to YCbCr if it can (2020-12-22 17:59:07 +0200) >> >> ---------------------------------------------------------------- >> Add support for DP-HDMI2.1 PCON >> >> From the series cover letter: >> >> This patch series attempts to add support for a DP-HDMI2.1 Protocol >> Convertor. The VESA spec for the HDMI2.1 PCON are proposed in Errata >> E5 to DisplayPort_v2.0: >> https://vesa.org/join-vesamemberships/member-downloads/?action=stamp&fileid=42299 >> The details are mentioned in: >> VESA DP-to-HDMI PCON Specification Standalone Document >> https://groups.vesa.org/wg/DP/document/15651 >> >> This series starts with adding support for FRL (Fixed Rate Link) >> Training between the PCON and HDMI2.1 sink. >> As per HDMI2.1 specification, a new data-channel or lane is added in >> FRL mode, by repurposing the TMDS clock Channel. Through FRL, higher >> bit-rate can be supported, ie. up to 12 Gbps/lane (48 Gbps over 4 >> lanes). >> >> With these patches, the HDMI2.1 PCON can be configured to achieve FRL >> training based on the maximum FRL rate supported by the panel, source >> and the PCON. >> The approach is to add the support for FRL training between PCON and >> HDMI2.1 sink and gradually add other blocks for supporting higher >> resolutions and other HDMI2.1 features, that can be supported by pcon >> for the sources that do not natively support HDMI2.1. >> >> This is done before the DP Link training between the source and PCON >> is started. In case of FRL training is not achieved, the PCON will >> work in the regular TMDS mode, without HDMI2.1 feature support. >> Any interruption in FRL training between the PCON and HDMI2.1 sink is >> notified through IRQ_HPD. On receiving the IRQ_HPD the concerned DPCD >> registers are read and FRL training is re-attempted. >> >> Currently, we have tested the FRL training and are able to enable 4K >> display with TGL Platform + Realtek PCON RTD2173 with HDMI2.1 supporting >> panel. >> >> ---------------------------------------------------------------- >> Ankit Nautiyal (11): >> drm/edid: Parse DSC1.2 cap fields from HFVSDB block >> drm/dp_helper: Add Helpers for FRL Link Training support for DP-HDMI2.1 PCON >> drm/dp_helper: Add support for Configuring DSC for HDMI2.1 Pcon >> drm/dp_helper: Add helpers to configure PCONs RGB-YCbCr Conversion >> drm/i915: Capture max frl rate for PCON in dfp cap structure >> drm/i915: Add support for starting FRL training for HDMI2.1 via PCON >> drm/i915: Check for FRL training before DP Link training >> drm/i915: Read DSC capabilities of the HDMI2.1 PCON encoder >> drm/i915: Add helper functions for calculating DSC parameters for HDMI2.1 >> drm/i915/display: Configure PCON for DSC1.1 to DSC1.2 encoding >> drm/i915/display: Let PCON convert from RGB to YCbCr if it can >> >> Swati Sharma (4): >> drm/edid: Add additional HFVSDB fields for HDMI2.1 >> drm/edid: Parse MAX_FRL field from HFVSDB block >> drm/dp_helper: Add support for link failure detection >> drm/i915: Add support for enabling link status and recovery >> >> drivers/gpu/drm/drm_dp_helper.c | 566 +++++++++++++++++++++ >> drivers/gpu/drm/drm_edid.c | 103 ++++ >> drivers/gpu/drm/i915/display/intel_ddi.c | 6 +- >> drivers/gpu/drm/i915/display/intel_display_types.h | 10 + >> drivers/gpu/drm/i915/display/intel_dp.c | 440 +++++++++++++++- >> drivers/gpu/drm/i915/display/intel_dp.h | 7 +- >> drivers/gpu/drm/i915/display/intel_hdmi.c | 233 +++++++++ >> drivers/gpu/drm/i915/display/intel_hdmi.h | 7 + >> include/drm/drm_connector.h | 49 ++ >> include/drm/drm_dp_helper.h | 218 ++++++++ >> include/drm/drm_edid.h | 30 ++ >> 11 files changed, 1650 insertions(+), 19 deletions(-) >> >> -- >> Jani Nikula, Intel Open Source Graphics Center
Hi Maarten, Maxime, and Thomas - Here's the DP-HDMI2.1 PCON support topic pull consisting of the series [1]. The series is split roughly 50-50 between drm helpers and i915, so a topic branch seemed to be the right way to go. I'll also pull this to drm-intel-next once you've merged to drm-misc-next. BR, Jani. [1] https://patchwork.freedesktop.org/series/82098/ topic/dp-hdmi-2.1-pcon-2020-12-23: Add support for DP-HDMI2.1 PCON From the series cover letter: This patch series attempts to add support for a DP-HDMI2.1 Protocol Convertor. The VESA spec for the HDMI2.1 PCON are proposed in Errata E5 to DisplayPort_v2.0: https://vesa.org/join-vesamemberships/member-downloads/?action=stamp&fileid=42299 The details are mentioned in: VESA DP-to-HDMI PCON Specification Standalone Document https://groups.vesa.org/wg/DP/document/15651 This series starts with adding support for FRL (Fixed Rate Link) Training between the PCON and HDMI2.1 sink. As per HDMI2.1 specification, a new data-channel or lane is added in FRL mode, by repurposing the TMDS clock Channel. Through FRL, higher bit-rate can be supported, ie. up to 12 Gbps/lane (48 Gbps over 4 lanes). With these patches, the HDMI2.1 PCON can be configured to achieve FRL training based on the maximum FRL rate supported by the panel, source and the PCON. The approach is to add the support for FRL training between PCON and HDMI2.1 sink and gradually add other blocks for supporting higher resolutions and other HDMI2.1 features, that can be supported by pcon for the sources that do not natively support HDMI2.1. This is done before the DP Link training between the source and PCON is started. In case of FRL training is not achieved, the PCON will work in the regular TMDS mode, without HDMI2.1 feature support. Any interruption in FRL training between the PCON and HDMI2.1 sink is notified through IRQ_HPD. On receiving the IRQ_HPD the concerned DPCD registers are read and FRL training is re-attempted. Currently, we have tested the FRL training and are able to enable 4K display with TGL Platform + Realtek PCON RTD2173 with HDMI2.1 supporting panel. The following changes since commit b3bf99daaee96a141536ce5c60a0d6dba6ec1d23: drm/i915/display: Defer initial modeset until after GGTT is initialised (2020-11-26 11:01:52 +0000) are available in the Git repository at: git://anongit.freedesktop.org/drm/drm-intel tags/topic/dp-hdmi-2.1-pcon-2020-12-23 for you to fetch changes up to 522508b665df3bbfdf40381d4e61777844b1703f: drm/i915/display: Let PCON convert from RGB to YCbCr if it can (2020-12-22 17:59:07 +0200) ---------------------------------------------------------------- Add support for DP-HDMI2.1 PCON From the series cover letter: This patch series attempts to add support for a DP-HDMI2.1 Protocol Convertor. The VESA spec for the HDMI2.1 PCON are proposed in Errata E5 to DisplayPort_v2.0: https://vesa.org/join-vesamemberships/member-downloads/?action=stamp&fileid=42299 The details are mentioned in: VESA DP-to-HDMI PCON Specification Standalone Document https://groups.vesa.org/wg/DP/document/15651 This series starts with adding support for FRL (Fixed Rate Link) Training between the PCON and HDMI2.1 sink. As per HDMI2.1 specification, a new data-channel or lane is added in FRL mode, by repurposing the TMDS clock Channel. Through FRL, higher bit-rate can be supported, ie. up to 12 Gbps/lane (48 Gbps over 4 lanes). With these patches, the HDMI2.1 PCON can be configured to achieve FRL training based on the maximum FRL rate supported by the panel, source and the PCON. The approach is to add the support for FRL training between PCON and HDMI2.1 sink and gradually add other blocks for supporting higher resolutions and other HDMI2.1 features, that can be supported by pcon for the sources that do not natively support HDMI2.1. This is done before the DP Link training between the source and PCON is started. In case of FRL training is not achieved, the PCON will work in the regular TMDS mode, without HDMI2.1 feature support. Any interruption in FRL training between the PCON and HDMI2.1 sink is notified through IRQ_HPD. On receiving the IRQ_HPD the concerned DPCD registers are read and FRL training is re-attempted. Currently, we have tested the FRL training and are able to enable 4K display with TGL Platform + Realtek PCON RTD2173 with HDMI2.1 supporting panel. ---------------------------------------------------------------- Ankit Nautiyal (11): drm/edid: Parse DSC1.2 cap fields from HFVSDB block drm/dp_helper: Add Helpers for FRL Link Training support for DP-HDMI2.1 PCON drm/dp_helper: Add support for Configuring DSC for HDMI2.1 Pcon drm/dp_helper: Add helpers to configure PCONs RGB-YCbCr Conversion drm/i915: Capture max frl rate for PCON in dfp cap structure drm/i915: Add support for starting FRL training for HDMI2.1 via PCON drm/i915: Check for FRL training before DP Link training drm/i915: Read DSC capabilities of the HDMI2.1 PCON encoder drm/i915: Add helper functions for calculating DSC parameters for HDMI2.1 drm/i915/display: Configure PCON for DSC1.1 to DSC1.2 encoding drm/i915/display: Let PCON convert from RGB to YCbCr if it can Swati Sharma (4): drm/edid: Add additional HFVSDB fields for HDMI2.1 drm/edid: Parse MAX_FRL field from HFVSDB block drm/dp_helper: Add support for link failure detection drm/i915: Add support for enabling link status and recovery drivers/gpu/drm/drm_dp_helper.c | 566 +++++++++++++++++++++ drivers/gpu/drm/drm_edid.c | 103 ++++ drivers/gpu/drm/i915/display/intel_ddi.c | 6 +- drivers/gpu/drm/i915/display/intel_display_types.h | 10 + drivers/gpu/drm/i915/display/intel_dp.c | 440 +++++++++++++++- drivers/gpu/drm/i915/display/intel_dp.h | 7 +- drivers/gpu/drm/i915/display/intel_hdmi.c | 233 +++++++++ drivers/gpu/drm/i915/display/intel_hdmi.h | 7 + include/drm/drm_connector.h | 49 ++ include/drm/drm_dp_helper.h | 218 ++++++++ include/drm/drm_edid.h | 30 ++ 11 files changed, 1650 insertions(+), 19 deletions(-)