| Message ID | a91eb6288331bb80b30534a31049cde508307fc0.1610110144.git.matti.vaittinen@fi.rohmeurope.com (mailing list archive) |
|---|---|
| State | Not Applicable, archived |
| Headers | show |
| Series | Support ROHM BD71815 PMIC | expand |
On Fri, Jan 08, 2021 at 03:34:16PM +0200, Matti Vaittinen wrote: > The BD71828 allows configuring the clk32kout pin mode to CMOS or > open-drain. Add device-tree property for specifying the preferred mode. > > Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> > --- > .../devicetree/bindings/mfd/rohm,bd71828-pmic.yaml | 7 +++++++ > 1 file changed, 7 insertions(+) > > diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml b/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml > index 3a6a1a26e2b3..cba085836bc0 100644 > --- a/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml > +++ b/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml > @@ -44,6 +44,13 @@ properties: > clock-output-names: > const: bd71828-32k-out > > + rohm,clkout-mode: > + description: clk32kout mode. Can be set to "open-drain" or "cmos". > + $ref: "/schemas/types.yaml#/definitions/string" > + enum: > + - open-drain > + - cmos > + I think a boolean or tristate ((0/1/not present) if you need 'leave default') would be better. > rohm,charger-sense-resistor-ohms: > minimum: 10000000 > maximum: 50000000 > -- > 2.25.4 > > > -- > Matti Vaittinen, Linux device drivers > ROHM Semiconductors, Finland SWDC > Kiviharjunlenkki 1E > 90220 OULU > FINLAND > > ~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~ > Simon says - in Latin please. > ~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~ > Thanks to Simon Glass for the translation =]
On Wed, 2021-01-13 at 07:52 -0600, Rob Herring wrote: > On Fri, Jan 08, 2021 at 03:34:16PM +0200, Matti Vaittinen wrote: > > The BD71828 allows configuring the clk32kout pin mode to CMOS or > > open-drain. Add device-tree property for specifying the preferred > > mode. > > > > Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> > > --- > > .../devicetree/bindings/mfd/rohm,bd71828-pmic.yaml | 7 > > +++++++ > > 1 file changed, 7 insertions(+) > > > > diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71828- > > pmic.yaml b/Documentation/devicetree/bindings/mfd/rohm,bd71828- > > pmic.yaml > > index 3a6a1a26e2b3..cba085836bc0 100644 > > --- a/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml > > +++ b/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml > > @@ -44,6 +44,13 @@ properties: > > clock-output-names: > > const: bd71828-32k-out > > > > + rohm,clkout-mode: > > + description: clk32kout mode. Can be set to "open-drain" or > > "cmos". > > + $ref: "/schemas/types.yaml#/definitions/string" > > + enum: > > + - open-drain > > + - cmos > > + > > I think a boolean or tristate ((0/1/not present) if you need 'leave > default') would be better. I was thinking of boolean but I hit the exact problem of leaving the default. (Booleans are so tempting for a lazy coder like me :] ) Do you mean uint with allowed values of 0/1 with the tristated? I can sure do that - but wouldn't open-drain / cmos be more descriptive? Best Regards Matti Vaittinen
On Wed, Jan 13, 2021 at 8:52 AM Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> wrote: > > > On Wed, 2021-01-13 at 07:52 -0600, Rob Herring wrote: > > On Fri, Jan 08, 2021 at 03:34:16PM +0200, Matti Vaittinen wrote: > > > The BD71828 allows configuring the clk32kout pin mode to CMOS or > > > open-drain. Add device-tree property for specifying the preferred > > > mode. > > > > > > Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> > > > --- > > > .../devicetree/bindings/mfd/rohm,bd71828-pmic.yaml | 7 > > > +++++++ > > > 1 file changed, 7 insertions(+) > > > > > > diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71828- > > > pmic.yaml b/Documentation/devicetree/bindings/mfd/rohm,bd71828- > > > pmic.yaml > > > index 3a6a1a26e2b3..cba085836bc0 100644 > > > --- a/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml > > > +++ b/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml > > > @@ -44,6 +44,13 @@ properties: > > > clock-output-names: > > > const: bd71828-32k-out > > > > > > + rohm,clkout-mode: > > > + description: clk32kout mode. Can be set to "open-drain" or > > > "cmos". > > > + $ref: "/schemas/types.yaml#/definitions/string" > > > + enum: > > > + - open-drain > > > + - cmos > > > + > > > > I think a boolean or tristate ((0/1/not present) if you need 'leave > > default') would be better. > > I was thinking of boolean but I hit the exact problem of leaving the > default. (Booleans are so tempting for a lazy coder like me :] ) Do you > mean uint with allowed values of 0/1 with the tristated? Yes. > I can sure do > that - but wouldn't open-drain / cmos be more descriptive? You'd get at least half by naming it 'rohm,clkout-open-drain'. I think anyone that knows what open-drain means will know what !open-drain implies. Rob
diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml b/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml index 3a6a1a26e2b3..cba085836bc0 100644 --- a/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml +++ b/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml @@ -44,6 +44,13 @@ properties: clock-output-names: const: bd71828-32k-out + rohm,clkout-mode: + description: clk32kout mode. Can be set to "open-drain" or "cmos". + $ref: "/schemas/types.yaml#/definitions/string" + enum: + - open-drain + - cmos + rohm,charger-sense-resistor-ohms: minimum: 10000000 maximum: 50000000
The BD71828 allows configuring the clk32kout pin mode to CMOS or open-drain. Add device-tree property for specifying the preferred mode. Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> --- .../devicetree/bindings/mfd/rohm,bd71828-pmic.yaml | 7 +++++++ 1 file changed, 7 insertions(+)