| Message ID | 1611113968-102424-1-git-send-email-dh10.jung@samsung.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | usb: dwc3: gadget: skip pullup and set_speed after suspend | expand |
Hi, Daehwan Jung wrote: > Sometimes dwc3_gadget_pullup and dwc3_gadget_set_speed are called after > entering suspend. That's why it needs to check whether suspend > > 1. dwc3 sends disconnect uevent and turn off. (suspend) > 2. Platform side causes pullup or set_speed(e.g., adbd closes ffs node) > 3. It causes unexpected behavior like ITMON error. > > Signed-off-by: Daehwan Jung <dh10.jung@samsung.com> > --- > drivers/usb/dwc3/gadget.c | 6 ++++++ > 1 file changed, 6 insertions(+) > > diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c > index ee44321..d7d4202 100644 > --- a/drivers/usb/dwc3/gadget.c > +++ b/drivers/usb/dwc3/gadget.c > @@ -2093,6 +2093,9 @@ static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on) > unsigned long flags; > int ret; > > + if (pm_runtime_suspended(dwc->dev)) > + return 0; > + > is_on = !!is_on; > > /* > @@ -2403,6 +2406,9 @@ static void dwc3_gadget_set_speed(struct usb_gadget *g, > unsigned long flags; > u32 reg; > > + if (pm_runtime_suspended(dwc->dev)) > + return; > + > spin_lock_irqsave(&dwc->lock, flags); > reg = dwc3_readl(dwc->regs, DWC3_DCFG); > reg &= ~(DWC3_DCFG_SPEED_MASK); This is already addressed in Wesley Cheng's patches. Can you try the latest changes of DWC3 in Greg's usb-next branch? Thanks, Thinh
Hi, On Thu, Jan 21, 2021 at 01:00:32AM +0000, Thinh Nguyen wrote: > Hi, > > Daehwan Jung wrote: > > Sometimes dwc3_gadget_pullup and dwc3_gadget_set_speed are called after > > entering suspend. That's why it needs to check whether suspend > > > > 1. dwc3 sends disconnect uevent and turn off. (suspend) > > 2. Platform side causes pullup or set_speed(e.g., adbd closes ffs node) > > 3. It causes unexpected behavior like ITMON error. > > > > Signed-off-by: Daehwan Jung <dh10.jung@samsung.com> > > --- > > drivers/usb/dwc3/gadget.c | 6 ++++++ > > 1 file changed, 6 insertions(+) > > > > diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c > > index ee44321..d7d4202 100644 > > --- a/drivers/usb/dwc3/gadget.c > > +++ b/drivers/usb/dwc3/gadget.c > > @@ -2093,6 +2093,9 @@ static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on) > > unsigned long flags; > > int ret; > > > > + if (pm_runtime_suspended(dwc->dev)) > > + return 0; > > + > > is_on = !!is_on; > > > > /* > > @@ -2403,6 +2406,9 @@ static void dwc3_gadget_set_speed(struct usb_gadget *g, > > unsigned long flags; > > u32 reg; > > > > + if (pm_runtime_suspended(dwc->dev)) > > + return; > > + > > spin_lock_irqsave(&dwc->lock, flags); > > reg = dwc3_readl(dwc->regs, DWC3_DCFG); > > reg &= ~(DWC3_DCFG_SPEED_MASK); > > This is already addressed in Wesley Cheng's patches. Can you try the > latest changes of DWC3 in Greg's usb-next branch? > > Thanks, > Thinh I checked Wesly Cheng's pathces but it's not same. What I want to do for this patch is to avoid pullup from platform side. (android in my case) It's possible that platform side tries to pullup by UDC_Store after usb is already disconnected. It can finally run controller and enable irq. I think we have to avoid it and other possible things related to platform side.
Hi, On Thu, Jan 21, 2021 at 01:00:32AM +0000, Thinh Nguyen wrote: > Hi, > > Daehwan Jung wrote: > > Sometimes dwc3_gadget_pullup and dwc3_gadget_set_speed are called after > > entering suspend. That's why it needs to check whether suspend > > > > 1. dwc3 sends disconnect uevent and turn off. (suspend) > > 2. Platform side causes pullup or set_speed(e.g., adbd closes ffs node) > > 3. It causes unexpected behavior like ITMON error. > > > > Signed-off-by: Daehwan Jung <dh10.jung@samsung.com> > > --- > > drivers/usb/dwc3/gadget.c | 6 ++++++ > > 1 file changed, 6 insertions(+) > > > > diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c > > index ee44321..d7d4202 100644 > > --- a/drivers/usb/dwc3/gadget.c > > +++ b/drivers/usb/dwc3/gadget.c > > @@ -2093,6 +2093,9 @@ static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on) > > unsigned long flags; > > int ret; > > > > + if (pm_runtime_suspended(dwc->dev)) > > + return 0; > > + > > is_on = !!is_on; > > > > /* > > @@ -2403,6 +2406,9 @@ static void dwc3_gadget_set_speed(struct usb_gadget *g, > > unsigned long flags; > > u32 reg; > > > > + if (pm_runtime_suspended(dwc->dev)) > > + return; > > + > > spin_lock_irqsave(&dwc->lock, flags); > > reg = dwc3_readl(dwc->regs, DWC3_DCFG); > > reg &= ~(DWC3_DCFG_SPEED_MASK); > > This is already addressed in Wesley Cheng's patches. Can you try the > latest changes of DWC3 in Greg's usb-next branch? > > Thanks, > Thinh I checked Wesly Cheng's pathces but it's not same. What I want to do for this patch is to avoid pullup from platform side. (android in my case) It's possible that platform side tries to pullup by UDC_Store after usb is already disconnected. It can finally run controller and enable irq. I think we have to avoid it and other possible things related to platform side. BR, Jung Daehwan
On 1/20/2021 10:49 PM, Jung Daehwan wrote: > Hi, > > On Thu, Jan 21, 2021 at 01:00:32AM +0000, Thinh Nguyen wrote: >> Hi, >> >> Daehwan Jung wrote: >>> Sometimes dwc3_gadget_pullup and dwc3_gadget_set_speed are called after >>> entering suspend. That's why it needs to check whether suspend >>> >>> 1. dwc3 sends disconnect uevent and turn off. (suspend) >>> 2. Platform side causes pullup or set_speed(e.g., adbd closes ffs node) >>> 3. It causes unexpected behavior like ITMON error. >>> >>> Signed-off-by: Daehwan Jung <dh10.jung@samsung.com> >>> --- >>> drivers/usb/dwc3/gadget.c | 6 ++++++ >>> 1 file changed, 6 insertions(+) >>> >>> diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c >>> index ee44321..d7d4202 100644 >>> --- a/drivers/usb/dwc3/gadget.c >>> +++ b/drivers/usb/dwc3/gadget.c >>> @@ -2093,6 +2093,9 @@ static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on) >>> unsigned long flags; >>> int ret; >>> >>> + if (pm_runtime_suspended(dwc->dev)) >>> + return 0; >>> + >>> is_on = !!is_on; >>> >>> /* >>> @@ -2403,6 +2406,9 @@ static void dwc3_gadget_set_speed(struct usb_gadget *g, >>> unsigned long flags; >>> u32 reg; >>> >>> + if (pm_runtime_suspended(dwc->dev)) >>> + return; >>> + >>> spin_lock_irqsave(&dwc->lock, flags); >>> reg = dwc3_readl(dwc->regs, DWC3_DCFG); >>> reg &= ~(DWC3_DCFG_SPEED_MASK); >> >> This is already addressed in Wesley Cheng's patches. Can you try the >> latest changes of DWC3 in Greg's usb-next branch? >> >> Thanks, >> Thinh > > I checked Wesly Cheng's pathces but it's not same. > What I want to do for this patch is to avoid pullup from platform side. > (android in my case) > > It's possible that platform side tries to pullup by UDC_Store after usb is already disconnected. > It can finally run controller and enable irq. > > I think we have to avoid it and other possible things related to platform side. > > Hi Daehwan, I think what you're trying to do is to avoid the unnecessary runtime resume if the cable is disconnected and userspace attempts to bind/unbind the UDC. I'm not exactly sure what patches you've pulled in, but assuming you didn't pull in any of the recent suspend changes: usb: dwc3: gadget: Allow runtime suspend if UDC unbinded usb: dwc3: gadget: Preserve UDC max speed setting Please consider the following scenario: 1. USB connected 2. UDC unbinded 3. DWC3 will continue to stay in runtime active, since dwc->connected = true In this scenario, we should allow the DWC3 to enter runtime suspend, since runstop has been disabled. If you have pulled in the above changes, and adding your changes on top of it, then consider the following: 1. USB connected 2. UDC unbinded 3. DWC enters runtime suspend (due to the above changes) 4. UDC binded The check for pm_runtime_suspended() will block step#4 from re-enabling the runstop bit even if the USB cable is connected. Thanks Wesley Cheng
On Wed, Jan 20, 2021 at 11:44:05PM -0800, Wesley Cheng wrote: > > > On 1/20/2021 10:49 PM, Jung Daehwan wrote: > > Hi, > > > > On Thu, Jan 21, 2021 at 01:00:32AM +0000, Thinh Nguyen wrote: > >> Hi, > >> > >> Daehwan Jung wrote: > >>> Sometimes dwc3_gadget_pullup and dwc3_gadget_set_speed are called after > >>> entering suspend. That's why it needs to check whether suspend > >>> > >>> 1. dwc3 sends disconnect uevent and turn off. (suspend) > >>> 2. Platform side causes pullup or set_speed(e.g., adbd closes ffs node) > >>> 3. It causes unexpected behavior like ITMON error. > >>> > >>> Signed-off-by: Daehwan Jung <dh10.jung@samsung.com> > >>> --- > >>> drivers/usb/dwc3/gadget.c | 6 ++++++ > >>> 1 file changed, 6 insertions(+) > >>> > >>> diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c > >>> index ee44321..d7d4202 100644 > >>> --- a/drivers/usb/dwc3/gadget.c > >>> +++ b/drivers/usb/dwc3/gadget.c > >>> @@ -2093,6 +2093,9 @@ static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on) > >>> unsigned long flags; > >>> int ret; > >>> > >>> + if (pm_runtime_suspended(dwc->dev)) > >>> + return 0; > >>> + > >>> is_on = !!is_on; > >>> > >>> /* > >>> @@ -2403,6 +2406,9 @@ static void dwc3_gadget_set_speed(struct usb_gadget *g, > >>> unsigned long flags; > >>> u32 reg; > >>> > >>> + if (pm_runtime_suspended(dwc->dev)) > >>> + return; > >>> + > >>> spin_lock_irqsave(&dwc->lock, flags); > >>> reg = dwc3_readl(dwc->regs, DWC3_DCFG); > >>> reg &= ~(DWC3_DCFG_SPEED_MASK); > >> > >> This is already addressed in Wesley Cheng's patches. Can you try the > >> latest changes of DWC3 in Greg's usb-next branch? > >> > >> Thanks, > >> Thinh > > > > I checked Wesly Cheng's pathces but it's not same. > > What I want to do for this patch is to avoid pullup from platform side. > > (android in my case) > > > > It's possible that platform side tries to pullup by UDC_Store after usb is already disconnected. > > It can finally run controller and enable irq. > > > > I think we have to avoid it and other possible things related to platform side. > > > > > > Hi Daehwan, > > I think what you're trying to do is to avoid the unnecessary runtime > resume if the cable is disconnected and userspace attempts to > bind/unbind the UDC. > > I'm not exactly sure what patches you've pulled in, but assuming you > didn't pull in any of the recent suspend changes: > > usb: dwc3: gadget: Allow runtime suspend if UDC unbinded > usb: dwc3: gadget: Preserve UDC max speed setting > > Please consider the following scenario: > 1. USB connected > 2. UDC unbinded > 3. DWC3 will continue to stay in runtime active, since dwc->connected = > true > > In this scenario, we should allow the DWC3 to enter runtime suspend, > since runstop has been disabled. > > If you have pulled in the above changes, and adding your changes on top > of it, then consider the following: > 1. USB connected > 2. UDC unbinded > 3. DWC enters runtime suspend (due to the above changes) > 4. UDC binded > > The check for pm_runtime_suspended() will block step#4 from re-enabling > the runstop bit even if the USB cable is connected. > > Thanks > Wesley Cheng > > -- > The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, > a Linux Foundation Collaborative Project > Hi Wesley The check for runtime_suspended() will block re-enabling the runstop bit as you said after pulling your patches in. UDC is contolled by userspace and it's possible UDC can be binded unexpectedly. That's why I think it needs to handle it even if the problem is from userspace. Below is an example in my environment. 1. USB disconnected 2. UDC unbinded 3. DWC enters runtime suspend 4. UDC binded unexpectedly 5. Gadget start and enable irq Line 9823: [ 36.024428][ T2889] dwc3 10e00000.dwc3: Turn off gadget dwc3-gadget Line 9827: [ 36.024572][ T2889] __dwc3_gadget_stop called Line 9828: [ 36.025083][ T2603] android_work: sent uevent USB_STATE=DISCONNECTED Line 9842: [ 36.200896][ T554] usb_gadget_disconnect Line 9843: [ 36.200916][ T554] dwc3_gadget_pullup : 0 Line 9844: [ 36.201165][ T554] dwc3_gadget_pullup: get_sync fail Line 9845: [ 36.201197][ T554] dwc3_gadget_stop called Line 9846: [ 36.201250][ T451] android_work: did not send uevent (0 0 0000000000000000) Line 9849: [ 36.202343][ T1] init: processing action (sys.usb.config=adb && sys.usb.configfs=1.. Line 9851: [ 36.203622][ T1] dwc3_gadget_start called Line 9852: [ 36.204079][ T1] usb_gadget_connect Line 9853: [ 36.204086][ T1] dwc3_gadget_pullup : 1 Line 9854: [ 36.204091][ T1] __dwc3_gadget_start called Best Regrars, Jung Daehwan
On 1/21/2021 12:13 AM, Jung Daehwan wrote: > On Wed, Jan 20, 2021 at 11:44:05PM -0800, Wesley Cheng wrote: >> >> >> On 1/20/2021 10:49 PM, Jung Daehwan wrote: >>> Hi, >>> >>> On Thu, Jan 21, 2021 at 01:00:32AM +0000, Thinh Nguyen wrote: >>>> Hi, >>>> >>>> Daehwan Jung wrote: >>>>> Sometimes dwc3_gadget_pullup and dwc3_gadget_set_speed are called after >>>>> entering suspend. That's why it needs to check whether suspend >>>>> >>>>> 1. dwc3 sends disconnect uevent and turn off. (suspend) >>>>> 2. Platform side causes pullup or set_speed(e.g., adbd closes ffs node) >>>>> 3. It causes unexpected behavior like ITMON error. >>>>> >>>>> Signed-off-by: Daehwan Jung <dh10.jung@samsung.com> >>>>> --- >>>>> drivers/usb/dwc3/gadget.c | 6 ++++++ >>>>> 1 file changed, 6 insertions(+) >>>>> >>>>> diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c >>>>> index ee44321..d7d4202 100644 >>>>> --- a/drivers/usb/dwc3/gadget.c >>>>> +++ b/drivers/usb/dwc3/gadget.c >>>>> @@ -2093,6 +2093,9 @@ static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on) >>>>> unsigned long flags; >>>>> int ret; >>>>> >>>>> + if (pm_runtime_suspended(dwc->dev)) >>>>> + return 0; >>>>> + >>>>> is_on = !!is_on; >>>>> >>>>> /* >>>>> @@ -2403,6 +2406,9 @@ static void dwc3_gadget_set_speed(struct usb_gadget *g, >>>>> unsigned long flags; >>>>> u32 reg; >>>>> >>>>> + if (pm_runtime_suspended(dwc->dev)) >>>>> + return; >>>>> + >>>>> spin_lock_irqsave(&dwc->lock, flags); >>>>> reg = dwc3_readl(dwc->regs, DWC3_DCFG); >>>>> reg &= ~(DWC3_DCFG_SPEED_MASK); >>>> >>>> This is already addressed in Wesley Cheng's patches. Can you try the >>>> latest changes of DWC3 in Greg's usb-next branch? >>>> >>>> Thanks, >>>> Thinh >>> >>> I checked Wesly Cheng's pathces but it's not same. >>> What I want to do for this patch is to avoid pullup from platform side. >>> (android in my case) >>> >>> It's possible that platform side tries to pullup by UDC_Store after usb is already disconnected. >>> It can finally run controller and enable irq. >>> >>> I think we have to avoid it and other possible things related to platform side. >>> >>> >> >> Hi Daehwan, >> >> I think what you're trying to do is to avoid the unnecessary runtime >> resume if the cable is disconnected and userspace attempts to >> bind/unbind the UDC. >> >> I'm not exactly sure what patches you've pulled in, but assuming you >> didn't pull in any of the recent suspend changes: >> >> usb: dwc3: gadget: Allow runtime suspend if UDC unbinded >> usb: dwc3: gadget: Preserve UDC max speed setting >> >> Please consider the following scenario: >> 1. USB connected >> 2. UDC unbinded >> 3. DWC3 will continue to stay in runtime active, since dwc->connected = >> true >> >> In this scenario, we should allow the DWC3 to enter runtime suspend, >> since runstop has been disabled. >> >> If you have pulled in the above changes, and adding your changes on top >> of it, then consider the following: >> 1. USB connected >> 2. UDC unbinded >> 3. DWC enters runtime suspend (due to the above changes) >> 4. UDC binded >> >> The check for pm_runtime_suspended() will block step#4 from re-enabling >> the runstop bit even if the USB cable is connected. >> >> Thanks >> Wesley Cheng >> >> -- >> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, >> a Linux Foundation Collaborative Project >> > > Hi Wesley > > The check for runtime_suspended() will block re-enabling the runstop bit as > you said after pulling your patches in. > > UDC is contolled by userspace and it's possible UDC can be binded > unexpectedly. That's why I think it needs to handle it even if the > problem is from userspace. > > Below is an example in my environment. > > 1. USB disconnected > 2. UDC unbinded > 3. DWC enters runtime suspend > 4. UDC binded unexpectedly > 5. Gadget start and enable irq > Hi Daehwan, If this is an unexpected event where userspace initiates the UDC bind sequence, then after the above sequence occurs, the DWC3 device should still be able to re-enter runtime suspend after the autosuspend timer expires. Since the cable is disconnected, the dwc->connected flag would still be false. Is this not happening in your situation? I'm just trying to understand what issue you're seeing other than the momentary transition from runtime suspend (due to cable disconnect) -->runtime resume (due to unexpected UDC bind) --> runtime suspend (due to nothing connected). Thanks Wesley Cheng > > Line 9823: [ 36.024428][ T2889] dwc3 10e00000.dwc3: Turn off gadget dwc3-gadget > Line 9827: [ 36.024572][ T2889] __dwc3_gadget_stop called > Line 9828: [ 36.025083][ T2603] android_work: sent uevent USB_STATE=DISCONNECTED > Line 9842: [ 36.200896][ T554] usb_gadget_disconnect > Line 9843: [ 36.200916][ T554] dwc3_gadget_pullup : 0 > Line 9844: [ 36.201165][ T554] dwc3_gadget_pullup: get_sync fail > Line 9845: [ 36.201197][ T554] dwc3_gadget_stop called > Line 9846: [ 36.201250][ T451] android_work: did not send uevent (0 0 0000000000000000) > Line 9849: [ 36.202343][ T1] init: processing action (sys.usb.config=adb && sys.usb.configfs=1.. > Line 9851: [ 36.203622][ T1] dwc3_gadget_start called > Line 9852: [ 36.204079][ T1] usb_gadget_connect > Line 9853: [ 36.204086][ T1] dwc3_gadget_pullup : 1 > Line 9854: [ 36.204091][ T1] __dwc3_gadget_start called > > Best Regrars, > Jung Daehwan > >
Hi, Daehwan Jung <dh10.jung@samsung.com> writes: > Sometimes dwc3_gadget_pullup and dwc3_gadget_set_speed are called after > entering suspend. That's why it needs to check whether suspend > > 1. dwc3 sends disconnect uevent and turn off. (suspend) > 2. Platform side causes pullup or set_speed(e.g., adbd closes ffs node) > 3. It causes unexpected behavior like ITMON error. please collect dwc3 trace events showing this problem.
On Sun, Jan 24, 2021 at 05:31:57PM +0200, Felipe Balbi wrote: > > Hi, > > Daehwan Jung <dh10.jung@samsung.com> writes: > > Sometimes dwc3_gadget_pullup and dwc3_gadget_set_speed are called after > > entering suspend. That's why it needs to check whether suspend > > > > 1. dwc3 sends disconnect uevent and turn off. (suspend) > > 2. Platform side causes pullup or set_speed(e.g., adbd closes ffs node) > > 3. It causes unexpected behavior like ITMON error. > > please collect dwc3 trace events showing this problem. > > -- > balbi Hi, balbi I'm sorry for late reply. I pulled in belo patch and that issue didn't occur usb: dwc3: gadget: Restart DWC3 gadget when enabling pullup @ Wesley cheng But, I think it needs to modify pm_rumtime_put to pm_runtime_put_sync_suspend for syncronization. pm_rumtime_put calls rumtime_idle not runtime_suspend Please check it. usb: dwc3: gadget: Allow runtime suspend if UDC unbinded Best Regards, Jung Daehwan
diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c index ee44321..d7d4202 100644 --- a/drivers/usb/dwc3/gadget.c +++ b/drivers/usb/dwc3/gadget.c @@ -2093,6 +2093,9 @@ static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on) unsigned long flags; int ret; + if (pm_runtime_suspended(dwc->dev)) + return 0; + is_on = !!is_on; /* @@ -2403,6 +2406,9 @@ static void dwc3_gadget_set_speed(struct usb_gadget *g, unsigned long flags; u32 reg; + if (pm_runtime_suspended(dwc->dev)) + return; + spin_lock_irqsave(&dwc->lock, flags); reg = dwc3_readl(dwc->regs, DWC3_DCFG); reg &= ~(DWC3_DCFG_SPEED_MASK);
Sometimes dwc3_gadget_pullup and dwc3_gadget_set_speed are called after entering suspend. That's why it needs to check whether suspend 1. dwc3 sends disconnect uevent and turn off. (suspend) 2. Platform side causes pullup or set_speed(e.g., adbd closes ffs node) 3. It causes unexpected behavior like ITMON error. Signed-off-by: Daehwan Jung <dh10.jung@samsung.com> --- drivers/usb/dwc3/gadget.c | 6 ++++++ 1 file changed, 6 insertions(+)