| Message ID | 20210416131657.3151464-2-steen.hegelund@microchip.com (mailing list archive) |
|---|---|
| State | Changes Requested |
| Delegated to: | Netdev Maintainers |
| Headers | show |
| Series | Adding the Sparx5 Switch Driver | expand |
| Context | Check | Description |
|---|---|---|
| netdev/cover_letter | success | Link |
| netdev/fixes_present | success | Link |
| netdev/patch_count | success | Link |
| netdev/tree_selection | success | Clearly marked for net-next |
| netdev/subject_prefix | success | Link |
| netdev/cc_maintainers | warning | 1 maintainers not CCed: Steen.Hegelund@microchip.com |
| netdev/source_inline | success | Was 0 now: 0 |
| netdev/verify_signedoff | success | Link |
| netdev/module_param | success | Was 0 now: 0 |
| netdev/build_32bit | success | Errors and warnings before: 0 this patch: 0 |
| netdev/kdoc | success | Errors and warnings before: 0 this patch: 0 |
| netdev/verify_fixes | success | Link |
| netdev/checkpatch | warning | WARNING: added, moved or deleted file(s), does MAINTAINERS need updating? |
| netdev/build_allmodconfig_warn | success | Errors and warnings before: 0 this patch: 0 |
| netdev/header_inline | success | Link |
On Fri, Apr 16, 2021 at 03:16:48PM +0200, Steen Hegelund wrote: > Document the Sparx5 switch device driver bindings > > Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com> > Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com> > Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com> > --- > .../bindings/net/microchip,sparx5-switch.yaml | 227 ++++++++++++++++++ > 1 file changed, 227 insertions(+) > create mode 100644 Documentation/devicetree/bindings/net/microchip,sparx5-switch.yaml > > diff --git a/Documentation/devicetree/bindings/net/microchip,sparx5-switch.yaml b/Documentation/devicetree/bindings/net/microchip,sparx5-switch.yaml > new file mode 100644 > index 000000000000..2eeb5230d8c8 > --- /dev/null > +++ b/Documentation/devicetree/bindings/net/microchip,sparx5-switch.yaml > @@ -0,0 +1,227 @@ > +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/net/microchip,sparx5-switch.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Microchip Sparx5 Ethernet switch controller > + > +maintainers: > + - Steen Hegelund <steen.hegelund@microchip.com> > + - Lars Povlsen <lars.povlsen@microchip.com> > + > +description: | > + The SparX-5 Enterprise Ethernet switch family provides a rich set of > + Enterprise switching features such as advanced TCAM-based VLAN and > + QoS processing enabling delivery of differentiated services, and > + security through TCAM-based frame processing using versatile content > + aware processor (VCAP). > + > + IPv4/IPv6 Layer 3 (L3) unicast and multicast routing is supported > + with up to 18K IPv4/9K IPv6 unicast LPM entries and up to 9K IPv4/3K > + IPv6 (S,G) multicast groups. > + > + L3 security features include source guard and reverse path > + forwarding (uRPF) tasks. Additional L3 features include VRF-Lite and > + IP tunnels (IP over GRE/IP). > + > + The SparX-5 switch family targets managed Layer 2 and Layer 3 > + equipment in SMB, SME, and Enterprise where high port count > + 1G/2.5G/5G/10G switching with 10G/25G aggregation links is required. > + > +properties: > + $nodename: > + pattern: "^switch@[0-9a-f]+$" > + > + compatible: > + const: microchip,sparx5-switch > + > + reg: > + minItems: 3 Drop, that's the default implied by 'items' length. Otherwise, Reviewed-by: Rob Herring <robh@kernel.org> > + items: > + - description: cpu target > + - description: devices target > + - description: general control block target > + > + reg-names: > + items: > + - const: cpu > + - const: devices > + - const: gcb > + > + interrupts: > + minItems: 1 > + items: > + - description: register based extraction > + - description: frame dma based extraction > + > + interrupt-names: > + minItems: 1 > + items: > + - const: xtr > + - const: fdma > + > + resets: > + items: > + - description: Reset controller used for switch core reset (soft reset) > + > + reset-names: > + items: > + - const: switch > + > + mac-address: true > + > + ethernet-ports: > + type: object > + patternProperties: > + "^port@[0-9a-f]+$": > + type: object > + > + properties: > + '#address-cells': > + const: 1 > + '#size-cells': > + const: 0 > + > + reg: > + description: Switch port number > + > + phys: > + maxItems: 1 > + description: > + phandle of a Ethernet SerDes PHY. This defines which SerDes > + instance will handle the Ethernet traffic. > + > + phy-mode: > + description: > + This specifies the interface used by the Ethernet SerDes towards > + the PHY or SFP. > + > + microchip,bandwidth: > + description: Specifies bandwidth in Mbit/s allocated to the port. > + $ref: "/schemas/types.yaml#/definitions/uint32" > + maximum: 25000 > + > + phy-handle: > + description: > + phandle of a Ethernet PHY. This is optional and if provided it > + points to the cuPHY used by the Ethernet SerDes. > + > + sfp: > + description: > + phandle of an SFP. This is optional and used when not specifying > + a cuPHY. It points to the SFP node that describes the SFP used by > + the Ethernet SerDes. > + > + managed: true > + > + microchip,sd-sgpio: > + description: > + Index of the ports Signal Detect SGPIO in the set of 384 SGPIOs > + This is optional, and only needed if the default used index is > + is not correct. > + $ref: "/schemas/types.yaml#/definitions/uint32" > + minimum: 0 > + maximum: 383 > + > + required: > + - reg > + - phys > + - phy-mode > + - microchip,bandwidth > + > + oneOf: > + - required: > + - phy-handle > + - required: > + - sfp > + - managed > + > +required: > + - compatible > + - reg > + - reg-names > + - interrupts > + - interrupt-names > + - resets > + - reset-names > + - ethernet-ports > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + switch: switch@600000000 { > + compatible = "microchip,sparx5-switch"; > + reg = <0 0x401000>, > + <0x10004000 0x7fc000>, > + <0x11010000 0xaf0000>; > + reg-names = "cpu", "devices", "gcb"; > + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "xtr"; > + resets = <&reset 0>; > + reset-names = "switch"; > + ethernet-ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port0: port@0 { > + reg = <0>; > + microchip,bandwidth = <1000>; > + phys = <&serdes 13>; > + phy-handle = <&phy0>; > + phy-mode = "qsgmii"; > + }; > + /* ... */ > + /* Then the 25G interfaces */ > + port60: port@60 { > + reg = <60>; > + microchip,bandwidth = <25000>; > + phys = <&serdes 29>; > + phy-mode = "10gbase-r"; > + sfp = <&sfp_eth60>; > + managed = "in-band-status"; > + microchip,sd-sgpio = <365>; > + }; > + port61: port@61 { > + reg = <61>; > + microchip,bandwidth = <25000>; > + phys = <&serdes 30>; > + phy-mode = "10gbase-r"; > + sfp = <&sfp_eth61>; > + managed = "in-band-status"; > + microchip,sd-sgpio = <369>; > + }; > + port62: port@62 { > + reg = <62>; > + microchip,bandwidth = <25000>; > + phys = <&serdes 31>; > + phy-mode = "10gbase-r"; > + sfp = <&sfp_eth62>; > + managed = "in-band-status"; > + microchip,sd-sgpio = <373>; > + }; > + port63: port@63 { > + reg = <63>; > + microchip,bandwidth = <25000>; > + phys = <&serdes 32>; > + phy-mode = "10gbase-r"; > + sfp = <&sfp_eth63>; > + managed = "in-band-status"; > + microchip,sd-sgpio = <377>; > + }; > + /* Finally the Management interface */ > + port64: port@64 { > + reg = <64>; > + microchip,bandwidth = <1000>; > + phys = <&serdes 0>; > + phy-handle = <&phy64>; > + phy-mode = "sgmii"; > + mac-address = [ 00 00 00 01 02 03 ]; > + }; > + }; > + }; > + > +... > +# vim: set ts=2 sw=2 sts=2 tw=80 et cc=80 ft=yaml : > -- > 2.31.1 >
diff --git a/Documentation/devicetree/bindings/net/microchip,sparx5-switch.yaml b/Documentation/devicetree/bindings/net/microchip,sparx5-switch.yaml new file mode 100644 index 000000000000..2eeb5230d8c8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/microchip,sparx5-switch.yaml @@ -0,0 +1,227 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/microchip,sparx5-switch.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip Sparx5 Ethernet switch controller + +maintainers: + - Steen Hegelund <steen.hegelund@microchip.com> + - Lars Povlsen <lars.povlsen@microchip.com> + +description: | + The SparX-5 Enterprise Ethernet switch family provides a rich set of + Enterprise switching features such as advanced TCAM-based VLAN and + QoS processing enabling delivery of differentiated services, and + security through TCAM-based frame processing using versatile content + aware processor (VCAP). + + IPv4/IPv6 Layer 3 (L3) unicast and multicast routing is supported + with up to 18K IPv4/9K IPv6 unicast LPM entries and up to 9K IPv4/3K + IPv6 (S,G) multicast groups. + + L3 security features include source guard and reverse path + forwarding (uRPF) tasks. Additional L3 features include VRF-Lite and + IP tunnels (IP over GRE/IP). + + The SparX-5 switch family targets managed Layer 2 and Layer 3 + equipment in SMB, SME, and Enterprise where high port count + 1G/2.5G/5G/10G switching with 10G/25G aggregation links is required. + +properties: + $nodename: + pattern: "^switch@[0-9a-f]+$" + + compatible: + const: microchip,sparx5-switch + + reg: + minItems: 3 + items: + - description: cpu target + - description: devices target + - description: general control block target + + reg-names: + items: + - const: cpu + - const: devices + - const: gcb + + interrupts: + minItems: 1 + items: + - description: register based extraction + - description: frame dma based extraction + + interrupt-names: + minItems: 1 + items: + - const: xtr + - const: fdma + + resets: + items: + - description: Reset controller used for switch core reset (soft reset) + + reset-names: + items: + - const: switch + + mac-address: true + + ethernet-ports: + type: object + patternProperties: + "^port@[0-9a-f]+$": + type: object + + properties: + '#address-cells': + const: 1 + '#size-cells': + const: 0 + + reg: + description: Switch port number + + phys: + maxItems: 1 + description: + phandle of a Ethernet SerDes PHY. This defines which SerDes + instance will handle the Ethernet traffic. + + phy-mode: + description: + This specifies the interface used by the Ethernet SerDes towards + the PHY or SFP. + + microchip,bandwidth: + description: Specifies bandwidth in Mbit/s allocated to the port. + $ref: "/schemas/types.yaml#/definitions/uint32" + maximum: 25000 + + phy-handle: + description: + phandle of a Ethernet PHY. This is optional and if provided it + points to the cuPHY used by the Ethernet SerDes. + + sfp: + description: + phandle of an SFP. This is optional and used when not specifying + a cuPHY. It points to the SFP node that describes the SFP used by + the Ethernet SerDes. + + managed: true + + microchip,sd-sgpio: + description: + Index of the ports Signal Detect SGPIO in the set of 384 SGPIOs + This is optional, and only needed if the default used index is + is not correct. + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 383 + + required: + - reg + - phys + - phy-mode + - microchip,bandwidth + + oneOf: + - required: + - phy-handle + - required: + - sfp + - managed + +required: + - compatible + - reg + - reg-names + - interrupts + - interrupt-names + - resets + - reset-names + - ethernet-ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + switch: switch@600000000 { + compatible = "microchip,sparx5-switch"; + reg = <0 0x401000>, + <0x10004000 0x7fc000>, + <0x11010000 0xaf0000>; + reg-names = "cpu", "devices", "gcb"; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "xtr"; + resets = <&reset 0>; + reset-names = "switch"; + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port0: port@0 { + reg = <0>; + microchip,bandwidth = <1000>; + phys = <&serdes 13>; + phy-handle = <&phy0>; + phy-mode = "qsgmii"; + }; + /* ... */ + /* Then the 25G interfaces */ + port60: port@60 { + reg = <60>; + microchip,bandwidth = <25000>; + phys = <&serdes 29>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth60>; + managed = "in-band-status"; + microchip,sd-sgpio = <365>; + }; + port61: port@61 { + reg = <61>; + microchip,bandwidth = <25000>; + phys = <&serdes 30>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth61>; + managed = "in-band-status"; + microchip,sd-sgpio = <369>; + }; + port62: port@62 { + reg = <62>; + microchip,bandwidth = <25000>; + phys = <&serdes 31>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth62>; + managed = "in-band-status"; + microchip,sd-sgpio = <373>; + }; + port63: port@63 { + reg = <63>; + microchip,bandwidth = <25000>; + phys = <&serdes 32>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth63>; + managed = "in-band-status"; + microchip,sd-sgpio = <377>; + }; + /* Finally the Management interface */ + port64: port@64 { + reg = <64>; + microchip,bandwidth = <1000>; + phys = <&serdes 0>; + phy-handle = <&phy64>; + phy-mode = "sgmii"; + mac-address = [ 00 00 00 01 02 03 ]; + }; + }; + }; + +... +# vim: set ts=2 sw=2 sts=2 tw=80 et cc=80 ft=yaml :