| Message ID | 20210420132614.150242-3-jitao.shi@mediatek.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [1/4] drm/panel: seperate panel power control from panel prepare/unprepare | expand |
Hi, Jitao: Jitao Shi <jitao.shi@mediatek.com> 於 2021年4月20日 週二 下午9:26寫道： > > Add the drm_panel_prepare_power and drm_panel_unprepare_power control. > Turn on panel power(drm_panel_prepare_power) and control before dsi > enable. And then dsi enable, send dcs cmd in drm_panel_prepare, last > turn on backlight. Please describe WHY do you need this patch? Fix any bug? > > Signed-off-by: Jitao Shi <jitao.shi@mediatek.com> > --- > drivers/gpu/drm/mediatek/mtk_dsi.c | 12 ++++++++++-- > 1 file changed, 10 insertions(+), 2 deletions(-) > > diff --git a/drivers/gpu/drm/mediatek/mtk_dsi.c b/drivers/gpu/drm/mediatek/mtk_dsi.c > index a1ff152ef468..455fe582c6b5 100644 > --- a/drivers/gpu/drm/mediatek/mtk_dsi.c > +++ b/drivers/gpu/drm/mediatek/mtk_dsi.c > @@ -615,10 +615,13 @@ static int mtk_dsi_poweron(struct mtk_dsi *dsi) > dsi->data_rate = DIV_ROUND_UP_ULL(dsi->vm.pixelclock * bit_per_pixel, > dsi->lanes); > > + if (panel_bridge_prepare_power(dsi->next_bridge)) ret = panel_bridge_prepare_power(dsi->next_bridge); if (ret) > + DRM_INFO("can't prepare power the panel\n"); I think you should goto err_refcount; > + > ret = clk_set_rate(dsi->hs_clk, dsi->data_rate); > if (ret < 0) { > dev_err(dev, "Failed to set data rate: %d\n", ret); > - goto err_refcount; > + goto err_prepare_power; > } > > phy_power_on(dsi->phy); > @@ -661,7 +664,9 @@ static int mtk_dsi_poweron(struct mtk_dsi *dsi) > clk_disable_unprepare(dsi->engine_clk); > err_phy_power_off: > phy_power_off(dsi->phy); > -err_refcount: > +err_prepare_power: > + if (panel_bridge_unprepare_power(dsi->next_bridge)) ret = panel_bridge_unprepare_power(dsi->next_bridge); > + DRM_INFO("Can't unprepare power the panel\n"); > dsi->refcount--; > return ret; > } > @@ -694,6 +699,9 @@ static void mtk_dsi_poweroff(struct mtk_dsi *dsi) > clk_disable_unprepare(dsi->digital_clk); > > phy_power_off(dsi->phy); > + > + if (panel_bridge_unprepare_power(dsi->next_bridge)) ret = panel_bridge_unprepare_power(dsi->next_bridge); > + DRM_INFO("Can't unprepare power the panel\n"); > } > > static void mtk_output_dsi_enable(struct mtk_dsi *dsi) > -- > 2.25.1 > _______________________________________________ > dri-devel mailing list > dri-devel@lists.freedesktop.org > https://lists.freedesktop.org/mailman/listinfo/dri-devel
On Sat, 2021-04-24 at 00:36 +0800, Chun-Kuang Hu wrote: > Hi, Jitao: > > Jitao Shi <jitao.shi@mediatek.com> 於 2021年4月20日 週二 下午9:26寫道： > > > > Add the drm_panel_prepare_power and drm_panel_unprepare_power control. > > Turn on panel power(drm_panel_prepare_power) and control before dsi > > enable. And then dsi enable, send dcs cmd in drm_panel_prepare, last > > turn on backlight. > > Please describe WHY do you need this patch? Fix any bug? Most panels, have five steps when poweron. 1. turn on dsi signal to LP11 --> dsi host's action 2. turn on the power supplies, --> panel's action 3. send the DCS cmd to panel --> panel's action 4. start send video stream --> dsi host's action 5. turn on backlight. --> panel's action we put "turn on the power supplies" and "send the DCS cmd to panel" in panel_prepare. And "turn on backlight" in panel_enable. But some other panels has a special poweron sequence as the following. 1. turn on the power supplies, --> panel's action 2. turn on dsi signal to LP11 --> dsi host's action 3. send the DCS cmd to panel --> panel's action 4. start send video stream --> dsi host's action 5. turn on backlight. --> panel's action panel's actions are divided into three parts. So I add a new api "drm_panel_prepare_power/rm_panel_unprepare_power" to control the sequence. Best Regards Jitao > > > > > Signed-off-by: Jitao Shi <jitao.shi@mediatek.com> > > --- > > drivers/gpu/drm/mediatek/mtk_dsi.c | 12 ++++++++++-- > > 1 file changed, 10 insertions(+), 2 deletions(-) > > > > diff --git a/drivers/gpu/drm/mediatek/mtk_dsi.c b/drivers/gpu/drm/mediatek/mtk_dsi.c > > index a1ff152ef468..455fe582c6b5 100644 > > --- a/drivers/gpu/drm/mediatek/mtk_dsi.c > > +++ b/drivers/gpu/drm/mediatek/mtk_dsi.c > > @@ -615,10 +615,13 @@ static int mtk_dsi_poweron(struct mtk_dsi *dsi) > > dsi->data_rate = DIV_ROUND_UP_ULL(dsi->vm.pixelclock * bit_per_pixel, > > dsi->lanes); > > > > + if (panel_bridge_prepare_power(dsi->next_bridge)) > > ret = panel_bridge_prepare_power(dsi->next_bridge); > if (ret) > > > + DRM_INFO("can't prepare power the panel\n"); > > I think you should goto err_refcount; Thanks for your review. I'll fix it next patch. > > > + > > ret = clk_set_rate(dsi->hs_clk, dsi->data_rate); > > if (ret < 0) { > > dev_err(dev, "Failed to set data rate: %d\n", ret); > > - goto err_refcount; > > + goto err_prepare_power; > > } > > > > phy_power_on(dsi->phy); > > @@ -661,7 +664,9 @@ static int mtk_dsi_poweron(struct mtk_dsi *dsi) > > clk_disable_unprepare(dsi->engine_clk); > > err_phy_power_off: > > phy_power_off(dsi->phy); > > -err_refcount: > > +err_prepare_power: > > + if (panel_bridge_unprepare_power(dsi->next_bridge)) > > ret = panel_bridge_unprepare_power(dsi->next_bridge); > > > + DRM_INFO("Can't unprepare power the panel\n"); > > dsi->refcount--; > > return ret; > > } > > @@ -694,6 +699,9 @@ static void mtk_dsi_poweroff(struct mtk_dsi *dsi) > > clk_disable_unprepare(dsi->digital_clk); > > > > phy_power_off(dsi->phy); > > + > > + if (panel_bridge_unprepare_power(dsi->next_bridge)) > > ret = panel_bridge_unprepare_power(dsi->next_bridge); > > > + DRM_INFO("Can't unprepare power the panel\n"); > > } > > > > static void mtk_output_dsi_enable(struct mtk_dsi *dsi) > > -- > > 2.25.1 > > _______________________________________________ > > dri-devel mailing list > > dri-devel@lists.freedesktop.org > > https://lists.freedesktop.org/mailman/listinfo/dri-devel
diff --git a/drivers/gpu/drm/mediatek/mtk_dsi.c b/drivers/gpu/drm/mediatek/mtk_dsi.c index a1ff152ef468..455fe582c6b5 100644 --- a/drivers/gpu/drm/mediatek/mtk_dsi.c +++ b/drivers/gpu/drm/mediatek/mtk_dsi.c @@ -615,10 +615,13 @@ static int mtk_dsi_poweron(struct mtk_dsi *dsi) dsi->data_rate = DIV_ROUND_UP_ULL(dsi->vm.pixelclock * bit_per_pixel, dsi->lanes); + if (panel_bridge_prepare_power(dsi->next_bridge)) + DRM_INFO("can't prepare power the panel\n"); + ret = clk_set_rate(dsi->hs_clk, dsi->data_rate); if (ret < 0) { dev_err(dev, "Failed to set data rate: %d\n", ret); - goto err_refcount; + goto err_prepare_power; } phy_power_on(dsi->phy); @@ -661,7 +664,9 @@ static int mtk_dsi_poweron(struct mtk_dsi *dsi) clk_disable_unprepare(dsi->engine_clk); err_phy_power_off: phy_power_off(dsi->phy); -err_refcount: +err_prepare_power: + if (panel_bridge_unprepare_power(dsi->next_bridge)) + DRM_INFO("Can't unprepare power the panel\n"); dsi->refcount--; return ret; } @@ -694,6 +699,9 @@ static void mtk_dsi_poweroff(struct mtk_dsi *dsi) clk_disable_unprepare(dsi->digital_clk); phy_power_off(dsi->phy); + + if (panel_bridge_unprepare_power(dsi->next_bridge)) + DRM_INFO("Can't unprepare power the panel\n"); } static void mtk_output_dsi_enable(struct mtk_dsi *dsi)
Add the drm_panel_prepare_power and drm_panel_unprepare_power control. Turn on panel power(drm_panel_prepare_power) and control before dsi enable. And then dsi enable, send dcs cmd in drm_panel_prepare, last turn on backlight. Signed-off-by: Jitao Shi <jitao.shi@mediatek.com> --- drivers/gpu/drm/mediatek/mtk_dsi.c | 12 ++++++++++-- 1 file changed, 10 insertions(+), 2 deletions(-)