| Message ID | 20210618030934.27376-1-ainux.wang@gmail.com (mailing list archive) |
|---|---|
| State | Changes Requested |
| Headers | show |
| Series | [v2] hwmon: (pmbus) Add support for MPS MP2949A | expand |
On Fri, Jun 18, 2021 at 11:09:34AM +0800, ainux.wang@gmail.com wrote: > From: "Ainux.Wang" <ainux.wang@gmail.com> > > Add support for MP2949A device from Monolithic Power Systems, Inc. (MPS). > This is a triple-loop, digital, multi-phase controller. > This device: > - Supports up to three power rail. > - Provides 6 pulse-width modulations (PWMs), and can be configured up > to 6-phase operation for Rail A , up to 2-phase operation for Rail B > and up to 1-phase operation for Rail C. > - The PMBus registers are distributed into three pages: Page 0, Page 1, > Page 2. Page 0 contains the registers for Rail A and most of the common > settings for all of the rails. Page 1 contains register information for > Rail B. Page 2 contains register information for Rail C. > - The MP2949A supports both 5mV VID step and 10mv VID step for IMVP8 and > IMVP9 with only one DAC for each rail to generate REF. > > Signed-off-by: Ainux.Wang <ainux.wang@gmail.com> > --- Change log goes here. My normal response to patches with missing change log is: <Formletter> Change log goes here. If it is missing, I won't know what changed. That means I will have to dig out older patch versions to compare. That costs time and would hold up both this patch as well as all other patches which I still have to review. For this reason, I will not review patches without change log. </Formletter> so you are lucky that your previous version is recent enough that I remember at least some of it. However, please do provide change logs in the future. > Documentation/hwmon/index.rst | 1 + > Documentation/hwmon/mp2949a.rst | 44 ++++++++++++ > drivers/hwmon/pmbus/Kconfig | 9 +++ > drivers/hwmon/pmbus/Makefile | 1 + > drivers/hwmon/pmbus/mp2949a.c | 119 ++++++++++++++++++++++++++++++++ > 5 files changed, 174 insertions(+) > create mode 100644 Documentation/hwmon/mp2949a.rst > create mode 100644 drivers/hwmon/pmbus/mp2949a.c > > diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst > index 9ed60fa84cbe..56aac3b1678d 100644 > --- a/Documentation/hwmon/index.rst > +++ b/Documentation/hwmon/index.rst > @@ -137,6 +137,7 @@ Hardware Monitoring Kernel Drivers > mcp3021 > menf21bmc > mlxreg-fan > + mp2949a > mp2975 > nct6683 > nct6775 > diff --git a/Documentation/hwmon/mp2949a.rst b/Documentation/hwmon/mp2949a.rst > new file mode 100644 > index 000000000000..ac4084e067f1 > --- /dev/null > +++ b/Documentation/hwmon/mp2949a.rst > @@ -0,0 +1,44 @@ > +.. SPDX-License-Identifier: GPL-2.0 > + > +Kernel driver mp2949a > +==================== > + > +Supported chips: > + > + * MPS MP2949A > + > + Prefix: 'mp2949a' > + > +Author: > + > + Ainux Wang <ainux.wang@gmail.com> > + > +Description > +----------- > + > +This driver implements support for Monolithic Power Systems, Inc. (MPS) > +triple-loop, digital, multi-phase controller MP2949A. > + > +This device: > + > +- Supports up to three power rail. rails > +- Provides 6 pulse-width modulations (PWMs), and can be configured up can be configured for ... > + to 6-phase operation for Rail A , up to 2-phase operation for Rail B Rail B, > + and up to 1-phase operation for Rail C. > +- The PMBus registers are distributed into three pages: Page 0, Page 1, > + Page 2. Page 0 contains the registers for Rail A and most of the common > + settings for all of the rails. Page 1 contains register information for > + Rail B. Page 2 contains register information for Rail C. > +- The MP2949A supports both 5mV VID step and 10mv VID step for IMVP8 and > + IMVP9 with only one DAC for each rail to generate REF. Please explain REF. > + > +Device supports: > + > +- SVID interface. > +- PMBus rev 1.2 interface. > + > +Device supports direct format for reading output power. > +Device supports linear format for reading input voltage and output current input voltage, output current, and temperature. > +and temperature. > +Device supports VID for reading output voltage. > +The below VID modes are supported: VR12, VR13, IMVP8, IMVP9. The following > diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig > index 37a5c39784fa..b1344b265976 100644 > --- a/drivers/hwmon/pmbus/Kconfig > +++ b/drivers/hwmon/pmbus/Kconfig > @@ -248,6 +248,15 @@ config SENSORS_MAX8688 > This driver can also be built as a module. If so, the module will > be called max8688. > > +config SENSORS_MP2949A > + tristate "MPS MP2949A" > + help > + If you say yes here you get hardware monitoring support for MPS > + MP2949A Triple Loop Digital Multi-Phase Controller. > + > + This driver can also be built as a module. If so, the module will > + be called mp2949a. > + > config SENSORS_MP2975 > tristate "MPS MP2975" > help > diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile > index f8dcc27cd56a..bfb55ab12da1 100644 > --- a/drivers/hwmon/pmbus/Makefile > +++ b/drivers/hwmon/pmbus/Makefile > @@ -28,6 +28,7 @@ obj-$(CONFIG_SENSORS_MAX20751) += max20751.o > obj-$(CONFIG_SENSORS_MAX31785) += max31785.o > obj-$(CONFIG_SENSORS_MAX34440) += max34440.o > obj-$(CONFIG_SENSORS_MAX8688) += max8688.o > +obj-$(CONFIG_SENSORS_MP2949A) += mp2949a.o > obj-$(CONFIG_SENSORS_MP2975) += mp2975.o > obj-$(CONFIG_SENSORS_PM6764TR) += pm6764tr.o > obj-$(CONFIG_SENSORS_PXE1610) += pxe1610.o > diff --git a/drivers/hwmon/pmbus/mp2949a.c b/drivers/hwmon/pmbus/mp2949a.c > new file mode 100644 > index 000000000000..d68e8526abe3 > --- /dev/null > +++ b/drivers/hwmon/pmbus/mp2949a.c > @@ -0,0 +1,119 @@ > +// SPDX-License-Identifier: GPL-2.0-or-later > +/* > + * Hardware monitoring driver for Monolithic Power Systems MP2949A > + * > + * Copyright (c) 2021 Lemote Technologies. All rights reserved. > + * Copyright (c) 2021 Ainux <ainux.wang@gmail.com> > + */ > + > +#include <linux/err.h> > +#include <linux/i2c.h> > +#include <linux/init.h> > +#include <linux/kernel.h> > +#include <linux/module.h> > +#include "pmbus.h" > + > +#define MP2949A_PAGE_NUM 3 > + > +static int mp2949a_read_byte_data(struct i2c_client *client, int page, int reg) > +{ > + switch (reg) { > + case PMBUS_VOUT_MODE: > + /* This chip do not support the VOUT_MODE command. */ s/do/does/ This warrants a more detailed explanation: What happens if the command is sent to the chip, and why is it not possible to rely on the standard response to unsupported commands ? > + return -EINVAL; > + default: > + return -ENODATA; > + } > +} > + > +static int mp2949a_identify(struct i2c_client *client, > + struct pmbus_driver_info *info) > +{ > + u8 vout_params; > + int i, ret; > + > + for (i = 0; i < MP2949A_PAGE_NUM; i++) { > + /* Read the register with VOUT scaling value.*/ > + ret = pmbus_read_byte_data(client, i, PMBUS_VOUT_MODE); ^^^^^^^^^^^^^^^ Should this be MFR_VR_CONFIG ? > + if (ret < 0) > + return ret; > + > + /* > + * Rail A bit 5, Rail B bit 4, Rail C bit 3. > + * 1'b1: 5mV (vr12/imvp8) > + * 1'b0: 10mv (imvp9) > + */ > + vout_params = ret & ~BIT(5-i); space before and after '-'. vout_params is really unnecessary; just do the check directly in the if() statement. > + if (vout_params) > + info->vrm_version[i] = vr12; > + else > + info->vrm_version[i] = imvp9; > + Unnecessary empty line. checkpatch --strict reports this and the above problem, plus another alignment problem. Please fix everything it reports. > + } > + > + return 0; > +} > + > +static struct pmbus_driver_info mp2949a_info = { > + .pages = MP2949A_PAGE_NUM, > + .format[PSC_VOLTAGE_IN] = linear, > + .format[PSC_VOLTAGE_OUT] = vid, > + .format[PSC_CURRENT_OUT] = linear, > + .format[PSC_TEMPERATURE] = linear, > + .format[PSC_POWER] = direct, > + .m[PSC_POWER] = 1, > + .b[PSC_POWER] = 0, > + .R[PSC_POWER] = 0, > + .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT | > + PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT | > + PMBUS_HAVE_TEMP | PMBUS_HAVE_POUT, > + .func[1] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT | > + PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT | > + PMBUS_HAVE_POUT, > + .func[2] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT | > + PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT | > + PMBUS_HAVE_POUT, > + .identify = mp2949a_identify, > + .read_byte_data = mp2949a_read_byte_data, > +}; > + > +static int mp2949a_probe(struct i2c_client *client, > + const struct i2c_device_id *id) > +{ > + struct pmbus_driver_info *info; > + > + info = devm_kmemdup(&client->dev, &mp2949a_info, sizeof(*info), > + GFP_KERNEL); > + if (!info) > + return -ENOMEM; > + > + return pmbus_do_probe(client, info); > +} > + > +static const struct i2c_device_id mp2949a_id[] = { > + {"mp2949a", 0}, > + {} > +}; > + > +MODULE_DEVICE_TABLE(i2c, mp2949a_id); > + > +static const struct of_device_id mp2949a_of_match[] = { > + {.compatible = "mps,mp2949a"}, > + {} > +}; > +MODULE_DEVICE_TABLE(of, mp2949a_of_match); > + > +static struct i2c_driver mp2949a_driver = { > + .driver = { > + .name = "mp2949a", > + .of_match_table = of_match_ptr(mp2949a_of_match), > + }, > + .probe = mp2949a_probe, > + .id_table = mp2949a_id, > +}; > + > +module_i2c_driver(mp2949a_driver); > + > +MODULE_AUTHOR("Ainux <ainux.wang@gmail.com>"); > +MODULE_DESCRIPTION("PMBus driver for Monolithic Power Systems MP2949A"); > +MODULE_LICENSE("GPL"); > -- > 2.18.1 >
Hi，Guenter
Thanks for the review. It all sounds reasonable. I'll address it all in v3.
Best regards,
Ainux Wang.
On Sat, 19 Jun 2021 at 03:39, Guenter Roeck <linux@roeck-us.net> wrote:
>
> On Fri, Jun 18, 2021 at 11:09:34AM +0800, ainux.wang@gmail.com wrote:
> > From: "Ainux.Wang" <ainux.wang@gmail.com>
> >
> > Add support for MP2949A device from Monolithic Power Systems, Inc. (MPS).
> > This is a triple-loop, digital, multi-phase controller.
> > This device:
> > - Supports up to three power rail.
> > - Provides 6 pulse-width modulations (PWMs), and can be configured up
> > to 6-phase operation for Rail A , up to 2-phase operation for Rail B
> > and up to 1-phase operation for Rail C.
> > - The PMBus registers are distributed into three pages: Page 0, Page 1,
> > Page 2. Page 0 contains the registers for Rail A and most of the common
> > settings for all of the rails. Page 1 contains register information for
> > Rail B. Page 2 contains register information for Rail C.
> > - The MP2949A supports both 5mV VID step and 10mv VID step for IMVP8 and
> > IMVP9 with only one DAC for each rail to generate REF.
> >
> > Signed-off-by: Ainux.Wang <ainux.wang@gmail.com>
> > ---
>
> Change log goes here. My normal response to patches with missing change log is:
>
> <Formletter>
> Change log goes here. If it is missing, I won't know what changed.
> That means I will have to dig out older patch versions to compare.
> That costs time and would hold up both this patch as well as all other
> patches which I still have to review.
>
> For this reason, I will not review patches without change log.
> </Formletter>
>
> so you are lucky that your previous version is recent enough that I remember
> at least some of it. However, please do provide change logs in the future.
>
> > Documentation/hwmon/index.rst | 1 +
> > Documentation/hwmon/mp2949a.rst | 44 ++++++++++++
> > drivers/hwmon/pmbus/Kconfig | 9 +++
> > drivers/hwmon/pmbus/Makefile | 1 +
> > drivers/hwmon/pmbus/mp2949a.c | 119 ++++++++++++++++++++++++++++++++
> > 5 files changed, 174 insertions(+)
> > create mode 100644 Documentation/hwmon/mp2949a.rst
> > create mode 100644 drivers/hwmon/pmbus/mp2949a.c
> >
> > diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst
> > index 9ed60fa84cbe..56aac3b1678d 100644
> > --- a/Documentation/hwmon/index.rst
> > +++ b/Documentation/hwmon/index.rst
> > @@ -137,6 +137,7 @@ Hardware Monitoring Kernel Drivers
> > mcp3021
> > menf21bmc
> > mlxreg-fan
> > + mp2949a
> > mp2975
> > nct6683
> > nct6775
> > diff --git a/Documentation/hwmon/mp2949a.rst b/Documentation/hwmon/mp2949a.rst
> > new file mode 100644
> > index 000000000000..ac4084e067f1
> > --- /dev/null
> > +++ b/Documentation/hwmon/mp2949a.rst
> > @@ -0,0 +1,44 @@
> > +.. SPDX-License-Identifier: GPL-2.0
> > +
> > +Kernel driver mp2949a
> > +====================
> > +
> > +Supported chips:
> > +
> > + * MPS MP2949A
> > +
> > + Prefix: 'mp2949a'
> > +
> > +Author:
> > +
> > + Ainux Wang <ainux.wang@gmail.com>
> > +
> > +Description
> > +-----------
> > +
> > +This driver implements support for Monolithic Power Systems, Inc. (MPS)
> > +triple-loop, digital, multi-phase controller MP2949A.
> > +
> > +This device:
> > +
> > +- Supports up to three power rail.
>
> rails
>
> > +- Provides 6 pulse-width modulations (PWMs), and can be configured up
>
> can be configured for ...
>
> > + to 6-phase operation for Rail A , up to 2-phase operation for Rail B
>
> Rail B,
>
> > + and up to 1-phase operation for Rail C.
> > +- The PMBus registers are distributed into three pages: Page 0, Page 1,
> > + Page 2. Page 0 contains the registers for Rail A and most of the common
> > + settings for all of the rails. Page 1 contains register information for
> > + Rail B. Page 2 contains register information for Rail C.
> > +- The MP2949A supports both 5mV VID step and 10mv VID step for IMVP8 and
> > + IMVP9 with only one DAC for each rail to generate REF.
>
> Please explain REF.
>
> > +
> > +Device supports:
> > +
> > +- SVID interface.
> > +- PMBus rev 1.2 interface.
> > +
> > +Device supports direct format for reading output power.
> > +Device supports linear format for reading input voltage and output current
>
> input voltage, output current, and temperature.
>
> > +and temperature.
> > +Device supports VID for reading output voltage.
> > +The below VID modes are supported: VR12, VR13, IMVP8, IMVP9.
>
> The following
>
> > diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
> > index 37a5c39784fa..b1344b265976 100644
> > --- a/drivers/hwmon/pmbus/Kconfig
> > +++ b/drivers/hwmon/pmbus/Kconfig
> > @@ -248,6 +248,15 @@ config SENSORS_MAX8688
> > This driver can also be built as a module. If so, the module will
> > be called max8688.
> >
> > +config SENSORS_MP2949A
> > + tristate "MPS MP2949A"
> > + help
> > + If you say yes here you get hardware monitoring support for MPS
> > + MP2949A Triple Loop Digital Multi-Phase Controller.
> > +
> > + This driver can also be built as a module. If so, the module will
> > + be called mp2949a.
> > +
> > config SENSORS_MP2975
> > tristate "MPS MP2975"
> > help
> > diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
> > index f8dcc27cd56a..bfb55ab12da1 100644
> > --- a/drivers/hwmon/pmbus/Makefile
> > +++ b/drivers/hwmon/pmbus/Makefile
> > @@ -28,6 +28,7 @@ obj-$(CONFIG_SENSORS_MAX20751) += max20751.o
> > obj-$(CONFIG_SENSORS_MAX31785) += max31785.o
> > obj-$(CONFIG_SENSORS_MAX34440) += max34440.o
> > obj-$(CONFIG_SENSORS_MAX8688) += max8688.o
> > +obj-$(CONFIG_SENSORS_MP2949A) += mp2949a.o
> > obj-$(CONFIG_SENSORS_MP2975) += mp2975.o
> > obj-$(CONFIG_SENSORS_PM6764TR) += pm6764tr.o
> > obj-$(CONFIG_SENSORS_PXE1610) += pxe1610.o
> > diff --git a/drivers/hwmon/pmbus/mp2949a.c b/drivers/hwmon/pmbus/mp2949a.c
> > new file mode 100644
> > index 000000000000..d68e8526abe3
> > --- /dev/null
> > +++ b/drivers/hwmon/pmbus/mp2949a.c
> > @@ -0,0 +1,119 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later
> > +/*
> > + * Hardware monitoring driver for Monolithic Power Systems MP2949A
> > + *
> > + * Copyright (c) 2021 Lemote Technologies. All rights reserved.
> > + * Copyright (c) 2021 Ainux <ainux.wang@gmail.com>
> > + */
> > +
> > +#include <linux/err.h>
> > +#include <linux/i2c.h>
> > +#include <linux/init.h>
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
> > +#include "pmbus.h"
> > +
> > +#define MP2949A_PAGE_NUM 3
> > +
> > +static int mp2949a_read_byte_data(struct i2c_client *client, int page, int reg)
> > +{
> > + switch (reg) {
> > + case PMBUS_VOUT_MODE:
> > + /* This chip do not support the VOUT_MODE command. */
>
> s/do/does/
>
> This warrants a more detailed explanation: What happens if the command
> is sent to the chip, and why is it not possible to rely on the standard
> response to unsupported commands ?
>
> > + return -EINVAL;
> > + default:
> > + return -ENODATA;
> > + }
> > +}
> > +
> > +static int mp2949a_identify(struct i2c_client *client,
> > + struct pmbus_driver_info *info)
> > +{
> > + u8 vout_params;
> > + int i, ret;
> > +
> > + for (i = 0; i < MP2949A_PAGE_NUM; i++) {
> > + /* Read the register with VOUT scaling value.*/
> > + ret = pmbus_read_byte_data(client, i, PMBUS_VOUT_MODE);
> ^^^^^^^^^^^^^^^
> Should this be MFR_VR_CONFIG ?
>
> > + if (ret < 0)
> > + return ret;
> > +
> > + /*
> > + * Rail A bit 5, Rail B bit 4, Rail C bit 3.
> > + * 1'b1: 5mV (vr12/imvp8)
> > + * 1'b0: 10mv (imvp9)
> > + */
> > + vout_params = ret & ~BIT(5-i);
>
> space before and after '-'. vout_params is really unnecessary; just do
> the check directly in the if() statement.
>
> > + if (vout_params)
> > + info->vrm_version[i] = vr12;
> > + else
> > + info->vrm_version[i] = imvp9;
> > +
>
> Unnecessary empty line.
>
> checkpatch --strict reports this and the above problem, plus another
> alignment problem. Please fix everything it reports.
>
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static struct pmbus_driver_info mp2949a_info = {
> > + .pages = MP2949A_PAGE_NUM,
> > + .format[PSC_VOLTAGE_IN] = linear,
> > + .format[PSC_VOLTAGE_OUT] = vid,
> > + .format[PSC_CURRENT_OUT] = linear,
> > + .format[PSC_TEMPERATURE] = linear,
> > + .format[PSC_POWER] = direct,
> > + .m[PSC_POWER] = 1,
> > + .b[PSC_POWER] = 0,
> > + .R[PSC_POWER] = 0,
> > + .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
> > + PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
> > + PMBUS_HAVE_TEMP | PMBUS_HAVE_POUT,
> > + .func[1] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
> > + PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
> > + PMBUS_HAVE_POUT,
> > + .func[2] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
> > + PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
> > + PMBUS_HAVE_POUT,
> > + .identify = mp2949a_identify,
> > + .read_byte_data = mp2949a_read_byte_data,
> > +};
> > +
> > +static int mp2949a_probe(struct i2c_client *client,
> > + const struct i2c_device_id *id)
> > +{
> > + struct pmbus_driver_info *info;
> > +
> > + info = devm_kmemdup(&client->dev, &mp2949a_info, sizeof(*info),
> > + GFP_KERNEL);
> > + if (!info)
> > + return -ENOMEM;
> > +
> > + return pmbus_do_probe(client, info);
> > +}
> > +
> > +static const struct i2c_device_id mp2949a_id[] = {
> > + {"mp2949a", 0},
> > + {}
> > +};
> > +
> > +MODULE_DEVICE_TABLE(i2c, mp2949a_id);
> > +
> > +static const struct of_device_id mp2949a_of_match[] = {
> > + {.compatible = "mps,mp2949a"},
> > + {}
> > +};
> > +MODULE_DEVICE_TABLE(of, mp2949a_of_match);
> > +
> > +static struct i2c_driver mp2949a_driver = {
> > + .driver = {
> > + .name = "mp2949a",
> > + .of_match_table = of_match_ptr(mp2949a_of_match),
> > + },
> > + .probe = mp2949a_probe,
> > + .id_table = mp2949a_id,
> > +};
> > +
> > +module_i2c_driver(mp2949a_driver);
> > +
> > +MODULE_AUTHOR("Ainux <ainux.wang@gmail.com>");
> > +MODULE_DESCRIPTION("PMBus driver for Monolithic Power Systems MP2949A");
> > +MODULE_LICENSE("GPL");
> > --
> > 2.18.1
> >
diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst index 9ed60fa84cbe..56aac3b1678d 100644 --- a/Documentation/hwmon/index.rst +++ b/Documentation/hwmon/index.rst @@ -137,6 +137,7 @@ Hardware Monitoring Kernel Drivers mcp3021 menf21bmc mlxreg-fan + mp2949a mp2975 nct6683 nct6775 diff --git a/Documentation/hwmon/mp2949a.rst b/Documentation/hwmon/mp2949a.rst new file mode 100644 index 000000000000..ac4084e067f1 --- /dev/null +++ b/Documentation/hwmon/mp2949a.rst @@ -0,0 +1,44 @@ +.. SPDX-License-Identifier: GPL-2.0 + +Kernel driver mp2949a +==================== + +Supported chips: + + * MPS MP2949A + + Prefix: 'mp2949a' + +Author: + + Ainux Wang <ainux.wang@gmail.com> + +Description +----------- + +This driver implements support for Monolithic Power Systems, Inc. (MPS) +triple-loop, digital, multi-phase controller MP2949A. + +This device: + +- Supports up to three power rail. +- Provides 6 pulse-width modulations (PWMs), and can be configured up + to 6-phase operation for Rail A , up to 2-phase operation for Rail B + and up to 1-phase operation for Rail C. +- The PMBus registers are distributed into three pages: Page 0, Page 1, + Page 2. Page 0 contains the registers for Rail A and most of the common + settings for all of the rails. Page 1 contains register information for + Rail B. Page 2 contains register information for Rail C. +- The MP2949A supports both 5mV VID step and 10mv VID step for IMVP8 and + IMVP9 with only one DAC for each rail to generate REF. + +Device supports: + +- SVID interface. +- PMBus rev 1.2 interface. + +Device supports direct format for reading output power. +Device supports linear format for reading input voltage and output current +and temperature. +Device supports VID for reading output voltage. +The below VID modes are supported: VR12, VR13, IMVP8, IMVP9. diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig index 37a5c39784fa..b1344b265976 100644 --- a/drivers/hwmon/pmbus/Kconfig +++ b/drivers/hwmon/pmbus/Kconfig @@ -248,6 +248,15 @@ config SENSORS_MAX8688 This driver can also be built as a module. If so, the module will be called max8688. +config SENSORS_MP2949A + tristate "MPS MP2949A" + help + If you say yes here you get hardware monitoring support for MPS + MP2949A Triple Loop Digital Multi-Phase Controller. + + This driver can also be built as a module. If so, the module will + be called mp2949a. + config SENSORS_MP2975 tristate "MPS MP2975" help diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile index f8dcc27cd56a..bfb55ab12da1 100644 --- a/drivers/hwmon/pmbus/Makefile +++ b/drivers/hwmon/pmbus/Makefile @@ -28,6 +28,7 @@ obj-$(CONFIG_SENSORS_MAX20751) += max20751.o obj-$(CONFIG_SENSORS_MAX31785) += max31785.o obj-$(CONFIG_SENSORS_MAX34440) += max34440.o obj-$(CONFIG_SENSORS_MAX8688) += max8688.o +obj-$(CONFIG_SENSORS_MP2949A) += mp2949a.o obj-$(CONFIG_SENSORS_MP2975) += mp2975.o obj-$(CONFIG_SENSORS_PM6764TR) += pm6764tr.o obj-$(CONFIG_SENSORS_PXE1610) += pxe1610.o diff --git a/drivers/hwmon/pmbus/mp2949a.c b/drivers/hwmon/pmbus/mp2949a.c new file mode 100644 index 000000000000..d68e8526abe3 --- /dev/null +++ b/drivers/hwmon/pmbus/mp2949a.c @@ -0,0 +1,119 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Hardware monitoring driver for Monolithic Power Systems MP2949A + * + * Copyright (c) 2021 Lemote Technologies. All rights reserved. + * Copyright (c) 2021 Ainux <ainux.wang@gmail.com> + */ + +#include <linux/err.h> +#include <linux/i2c.h> +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include "pmbus.h" + +#define MP2949A_PAGE_NUM 3 + +static int mp2949a_read_byte_data(struct i2c_client *client, int page, int reg) +{ + switch (reg) { + case PMBUS_VOUT_MODE: + /* This chip do not support the VOUT_MODE command. */ + return -EINVAL; + default: + return -ENODATA; + } +} + +static int mp2949a_identify(struct i2c_client *client, + struct pmbus_driver_info *info) +{ + u8 vout_params; + int i, ret; + + for (i = 0; i < MP2949A_PAGE_NUM; i++) { + /* Read the register with VOUT scaling value.*/ + ret = pmbus_read_byte_data(client, i, PMBUS_VOUT_MODE); + if (ret < 0) + return ret; + + /* + * Rail A bit 5, Rail B bit 4, Rail C bit 3. + * 1'b1: 5mV (vr12/imvp8) + * 1'b0: 10mv (imvp9) + */ + vout_params = ret & ~BIT(5-i); + if (vout_params) + info->vrm_version[i] = vr12; + else + info->vrm_version[i] = imvp9; + + } + + return 0; +} + +static struct pmbus_driver_info mp2949a_info = { + .pages = MP2949A_PAGE_NUM, + .format[PSC_VOLTAGE_IN] = linear, + .format[PSC_VOLTAGE_OUT] = vid, + .format[PSC_CURRENT_OUT] = linear, + .format[PSC_TEMPERATURE] = linear, + .format[PSC_POWER] = direct, + .m[PSC_POWER] = 1, + .b[PSC_POWER] = 0, + .R[PSC_POWER] = 0, + .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT | + PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT | + PMBUS_HAVE_TEMP | PMBUS_HAVE_POUT, + .func[1] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT | + PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT | + PMBUS_HAVE_POUT, + .func[2] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT | + PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT | + PMBUS_HAVE_POUT, + .identify = mp2949a_identify, + .read_byte_data = mp2949a_read_byte_data, +}; + +static int mp2949a_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct pmbus_driver_info *info; + + info = devm_kmemdup(&client->dev, &mp2949a_info, sizeof(*info), + GFP_KERNEL); + if (!info) + return -ENOMEM; + + return pmbus_do_probe(client, info); +} + +static const struct i2c_device_id mp2949a_id[] = { + {"mp2949a", 0}, + {} +}; + +MODULE_DEVICE_TABLE(i2c, mp2949a_id); + +static const struct of_device_id mp2949a_of_match[] = { + {.compatible = "mps,mp2949a"}, + {} +}; +MODULE_DEVICE_TABLE(of, mp2949a_of_match); + +static struct i2c_driver mp2949a_driver = { + .driver = { + .name = "mp2949a", + .of_match_table = of_match_ptr(mp2949a_of_match), + }, + .probe = mp2949a_probe, + .id_table = mp2949a_id, +}; + +module_i2c_driver(mp2949a_driver); + +MODULE_AUTHOR("Ainux <ainux.wang@gmail.com>"); +MODULE_DESCRIPTION("PMBus driver for Monolithic Power Systems MP2949A"); +MODULE_LICENSE("GPL");