| Message ID | 1628334401-6577-1-git-send-email-stefan.wahren@i2se.com (mailing list archive) |
|---|---|
| Headers | show |
| Series | ARM: dts: Add Raspberry Pi CM4 & CM4 IO Board support | expand |
On 8/7/2021 1:06 PM, Stefan Wahren wrote: > This series add support for the Raspberry Pi Compute Module 4 and its > IO board. > > Changes in V2: > - drop emmc2bus patch as it affects userspace (thanks to Marc Zyngier) > - tested with CM4 and integrate sdhci patches from Nicolas (just include kHz fixups) > - add Rob's Acked-by > - add HS200 property to emmc2 node for a slight performance gain > - move antenna comment to the proper position Nicolas, I am assuming you will be picking up these patches and submit a BCM283x pull request with them. Thanks! > > Nicolas Saenz Julienne (2): > mmc: sdhci-iproc: Cap min clock frequency on BCM2711 > mmc: sdhci-iproc: Set SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN on BCM2711 > > Stefan Wahren (8): > ARM: dts: bcm2711: fix MDIO #address- and #size-cells > ARM: dts: bcm2711-rpi-4-b: fix sd_io_1v8_reg regulator states > dt-bindings: display: bcm2835: add optional property power-domains > ARM: dts: bcm283x-rpi: Move Wifi/BT into separate dtsi > dt-bindings: arm: bcm2835: Add Raspberry Pi Compute Module 4 > ARM: dts: Add Raspberry Pi Compute Module 4 > ARM: dts: Add Raspberry Pi Compute Module 4 IO Board > arm64: dts: broadcom: Add reference to RPi CM4 IO Board > > .../devicetree/bindings/arm/bcm/bcm2835.yaml | 1 + > .../bindings/display/brcm,bcm2835-dsi0.yaml | 3 + > .../bindings/display/brcm,bcm2835-hdmi.yaml | 3 + > .../bindings/display/brcm,bcm2835-v3d.yaml | 3 + > .../bindings/display/brcm,bcm2835-vec.yaml | 3 + > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/bcm2711-rpi-4-b.dts | 42 ++----- > arch/arm/boot/dts/bcm2711-rpi-cm4-io.dts | 138 +++++++++++++++++++++ > arch/arm/boot/dts/bcm2711-rpi-cm4.dtsi | 113 +++++++++++++++++ > arch/arm/boot/dts/bcm2711.dtsi | 4 +- > arch/arm/boot/dts/bcm2835-rpi-zero-w.dts | 31 ++--- > arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts | 36 ++---- > arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts | 36 ++---- > arch/arm/boot/dts/bcm2837-rpi-3-b.dts | 36 ++---- > arch/arm/boot/dts/bcm283x-rpi-wifi-bt.dtsi | 34 +++++ > arch/arm64/boot/dts/broadcom/Makefile | 1 + > .../arm64/boot/dts/broadcom/bcm2711-rpi-cm4-io.dts | 2 + > drivers/mmc/host/sdhci-iproc.c | 21 +++- > 18 files changed, 366 insertions(+), 142 deletions(-) > create mode 100644 arch/arm/boot/dts/bcm2711-rpi-cm4-io.dts > create mode 100644 arch/arm/boot/dts/bcm2711-rpi-cm4.dtsi > create mode 100644 arch/arm/boot/dts/bcm283x-rpi-wifi-bt.dtsi > create mode 100644 arch/arm64/boot/dts/broadcom/bcm2711-rpi-cm4-io.dts >
Hi Florian, On Sun, 2021-08-22 at 12:31 +0200, Florian Fainelli wrote: > > On 8/7/2021 1:06 PM, Stefan Wahren wrote: > > This series add support for the Raspberry Pi Compute Module 4 and its > > IO board. > > > > Changes in V2: > > - drop emmc2bus patch as it affects userspace (thanks to Marc Zyngier) > > - tested with CM4 and integrate sdhci patches from Nicolas (just include kHz fixups) > > - add Rob's Acked-by > > - add HS200 property to emmc2 node for a slight performance gain > > - move antenna comment to the proper position > > Nicolas, I am assuming you will be picking up these patches and submit a > BCM283x pull request with them. Thanks! Yes, sorry for the late replies. I'm just back from vacation. Regards, Nicolas
Hi Stefan, On Sat, 2021-08-07 at 13:06 +0200, Stefan Wahren wrote: > This series add support for the Raspberry Pi Compute Module 4 and its > IO board. Sorry for the late review. I finally got some time to review/test this properly. The devicetree patches look really good, dtbs_check's shows no new errors, and all peripherals work. The only thing I can't verify is PCIe as I have nothing to plug into it, but it should work. I'll apply the series (modulo the mmc patches) for-next soon. Thanks! > Changes in V2: > - drop emmc2bus patch as it affects userspace (thanks to Marc Zyngier) > - tested with CM4 and integrate sdhci patches from Nicolas (just include kHz fixups) > - add Rob's Acked-by > - add HS200 property to emmc2 node for a slight performance gain > - move antenna comment to the proper position > > Nicolas Saenz Julienne (2): > mmc: sdhci-iproc: Cap min clock frequency on BCM2711 > mmc: sdhci-iproc: Set SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN on BCM2711 > > Stefan Wahren (8): > ARM: dts: bcm2711: fix MDIO #address- and #size-cells > ARM: dts: bcm2711-rpi-4-b: fix sd_io_1v8_reg regulator states > dt-bindings: display: bcm2835: add optional property power-domains > ARM: dts: bcm283x-rpi: Move Wifi/BT into separate dtsi > dt-bindings: arm: bcm2835: Add Raspberry Pi Compute Module 4 > ARM: dts: Add Raspberry Pi Compute Module 4 > ARM: dts: Add Raspberry Pi Compute Module 4 IO Board > arm64: dts: broadcom: Add reference to RPi CM4 IO Board > > .../devicetree/bindings/arm/bcm/bcm2835.yaml | 1 + > .../bindings/display/brcm,bcm2835-dsi0.yaml | 3 + > .../bindings/display/brcm,bcm2835-hdmi.yaml | 3 + > .../bindings/display/brcm,bcm2835-v3d.yaml | 3 + > .../bindings/display/brcm,bcm2835-vec.yaml | 3 + > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/bcm2711-rpi-4-b.dts | 42 ++----- > arch/arm/boot/dts/bcm2711-rpi-cm4-io.dts | 138 +++++++++++++++++++++ > arch/arm/boot/dts/bcm2711-rpi-cm4.dtsi | 113 +++++++++++++++++ > arch/arm/boot/dts/bcm2711.dtsi | 4 +- > arch/arm/boot/dts/bcm2835-rpi-zero-w.dts | 31 ++--- > arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts | 36 ++---- > arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts | 36 ++---- > arch/arm/boot/dts/bcm2837-rpi-3-b.dts | 36 ++---- > arch/arm/boot/dts/bcm283x-rpi-wifi-bt.dtsi | 34 +++++ > arch/arm64/boot/dts/broadcom/Makefile | 1 + > .../arm64/boot/dts/broadcom/bcm2711-rpi-cm4-io.dts | 2 + > drivers/mmc/host/sdhci-iproc.c | 21 +++- > 18 files changed, 366 insertions(+), 142 deletions(-) > create mode 100644 arch/arm/boot/dts/bcm2711-rpi-cm4-io.dts > create mode 100644 arch/arm/boot/dts/bcm2711-rpi-cm4.dtsi > create mode 100644 arch/arm/boot/dts/bcm283x-rpi-wifi-bt.dtsi > create mode 100644 arch/arm64/boot/dts/broadcom/bcm2711-rpi-cm4-io.dts >