deleted file mode 100644
@@ -1,84 +0,0 @@
-QCOM Idle States for cpuidle driver
-
-ARM provides idle-state node to define the cpuidle states, as defined in [1].
-cpuidle-qcom is the cpuidle driver for Qualcomm SoCs and uses these idle
-states. Idle states have different enter/exit latency and residency values.
-The idle states supported by the QCOM SoC are defined as -
-
- * Standby
- * Retention
- * Standalone Power Collapse (Standalone PC or SPC)
- * Power Collapse (PC)
-
-Standby: Standby does a little more in addition to architectural clock gating.
-When the WFI instruction is executed the ARM core would gate its internal
-clocks. In addition to gating the clocks, QCOM cpus use this instruction as a
-trigger to execute the SPM state machine. The SPM state machine waits for the
-interrupt to trigger the core back in to active. This triggers the cache
-hierarchy to enter standby states, when all cpus are idle. An interrupt brings
-the SPM state machine out of its wait, the next step is to ensure that the
-cache hierarchy is also out of standby, and then the cpu is allowed to resume
-execution. This state is defined as a generic ARM WFI state by the ARM cpuidle
-driver and is not defined in the DT. The SPM state machine should be
-configured to execute this state by default and after executing every other
-state below.
-
-Retention: Retention is a low power state where the core is clock gated and
-the memory and the registers associated with the core are retained. The
-voltage may be reduced to the minimum value needed to keep the processor
-registers active. The SPM should be configured to execute the retention
-sequence and would wait for interrupt, before restoring the cpu to execution
-state. Retention may have a slightly higher latency than Standby.
-
-Standalone PC: A cpu can power down and warmboot if there is a sufficient time
-between the time it enters idle and the next known wake up. SPC mode is used
-to indicate a core entering a power down state without consulting any other
-cpu or the system resources. This helps save power only on that core. The SPM
-sequence for this idle state is programmed to power down the supply to the
-core, wait for the interrupt, restore power to the core, and ensure the
-system state including cache hierarchy is ready before allowing core to
-resume. Applying power and resetting the core causes the core to warmboot
-back into Elevation Level (EL) which trampolines the control back to the
-kernel. Entering a power down state for the cpu, needs to be done by trapping
-into a EL. Failing to do so, would result in a crash enforced by the warm boot
-code in the EL for the SoC. On SoCs with write-back L1 cache, the cache has to
-be flushed in s/w, before powering down the core.
-
-Power Collapse: This state is similar to the SPC mode, but distinguishes
-itself in that the cpu acknowledges and permits the SoC to enter deeper sleep
-modes. In a hierarchical power domain SoC, this means L2 and other caches can
-be flushed, system bus, clocks - lowered, and SoC main XO clock gated and
-voltages reduced, provided all cpus enter this state. Since the span of low
-power modes possible at this state is vast, the exit latency and the residency
-of this low power mode would be considered high even though at a cpu level,
-this essentially is cpu power down. The SPM in this state also may handshake
-with the Resource power manager (RPM) processor in the SoC to indicate a
-complete application processor subsystem shut down.
-
-The idle-state for QCOM SoCs are distinguished by the compatible property of
-the idle-states device node.
-
-The devicetree representation of the idle state should be -
-
-Required properties:
-
-- compatible: Must be one of -
- "qcom,idle-state-ret",
- "qcom,idle-state-spc",
- "qcom,idle-state-pc",
- and "arm,idle-state".
-
-Other required and optional properties are specified in [1].
-
-Example:
-
- idle-states {
- CPU_SPC: spc {
- compatible = "qcom,idle-state-spc", "arm,idle-state";
- entry-latency-us = <150>;
- exit-latency-us = <200>;
- min-residency-us = <2000>;
- };
- };
-
-[1]. Documentation/devicetree/bindings/arm/idle-states.yaml
new file mode 100644
@@ -0,0 +1,126 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/arm/msm/qcom,idle-state.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: QCOM Idle States binding description
+
+maintainers:
+ - Bjorn Andersson <bjorn.andersson@linaro.org>
+
+description: |
+ ARM provides idle-state node to define the cpuidle states, as defined in [1].
+ cpuidle-qcom is the cpuidle driver for Qualcomm SoCs and uses these idle
+ states. Idle states have different enter/exit latency and residency values.
+ The idle states supported by the QCOM SoC are defined as -
+
+ * Standby
+ * Retention
+ * Standalone Power Collapse (Standalone PC or SPC)
+ * Power Collapse (PC)
+
+ Standby: Standby does a little more in addition to architectural clock gating.
+ When the WFI instruction is executed the ARM core would gate its internal
+ clocks. In addition to gating the clocks, QCOM cpus use this instruction as a
+ trigger to execute the SPM state machine. The SPM state machine waits for the
+ interrupt to trigger the core back in to active. This triggers the cache
+ hierarchy to enter standby states, when all cpus are idle. An interrupt brings
+ the SPM state machine out of its wait, the next step is to ensure that the
+ cache hierarchy is also out of standby, and then the cpu is allowed to resume
+ execution. This state is defined as a generic ARM WFI state by the ARM cpuidle
+ driver and is not defined in the DT. The SPM state machine should be
+ configured to execute this state by default and after executing every other
+ state below.
+
+ Retention: Retention is a low power state where the core is clock gated and
+ the memory and the registers associated with the core are retained. The
+ voltage may be reduced to the minimum value needed to keep the processor
+ registers active. The SPM should be configured to execute the retention
+ sequence and would wait for interrupt, before restoring the cpu to execution
+ state. Retention may have a slightly higher latency than Standby.
+
+ Standalone PC: A cpu can power down and warmboot if there is a sufficient time
+ between the time it enters idle and the next known wake up. SPC mode is used
+ to indicate a core entering a power down state without consulting any other
+ cpu or the system resources. This helps save power only on that core. The SPM
+ sequence for this idle state is programmed to power down the supply to the
+ core, wait for the interrupt, restore power to the core, and ensure the
+ system state including cache hierarchy is ready before allowing core to
+ resume. Applying power and resetting the core causes the core to warmboot
+ back into Elevation Level (EL) which trampolines the control back to the
+ kernel. Entering a power down state for the cpu, needs to be done by trapping
+ into a EL. Failing to do so, would result in a crash enforced by the warm boot
+ code in the EL for the SoC. On SoCs with write-back L1 cache, the cache has to
+ be flushed in s/w, before powering down the core.
+
+ Power Collapse: This state is similar to the SPC mode, but distinguishes
+ itself in that the cpu acknowledges and permits the SoC to enter deeper sleep
+ modes. In a hierarchical power domain SoC, this means L2 and other caches can
+ be flushed, system bus, clocks - lowered, and SoC main XO clock gated and
+ voltages reduced, provided all cpus enter this state. Since the span of low
+ power modes possible at this state is vast, the exit latency and the residency
+ of this low power mode would be considered high even though at a cpu level,
+ this essentially is cpu power down. The SPM in this state also may handshake
+ with the Resource power manager (RPM) processor in the SoC to indicate a
+ complete application processor subsystem shut down.
+
+ The idle-state for QCOM SoCs are distinguished by the compatible property of
+ the idle-states device node.
+
+ [1] Documentation/devicetree/bindings/arm/idle-states.yaml
+
+properties:
+ $nodename:
+ const: idle-states
+
+patternProperties:
+ "^(ret|spc|pc)$":
+ type: object
+ description:
+ Each state node represents a domain idle state description.
+
+ properties:
+ compatible:
+ items:
+ - enum:
+ - qcom,idle-state-ret
+ - qcom,idle-state-spc
+ - qcom,idle-state-pc
+ - const: arm,idle-state
+
+ entry-latency-us:
+ description:
+ The worst case latency in microseconds required to enter the idle
+ state. Note that, the exit-latency-us duration may be guaranteed only
+ after the entry-latency-us has passed.
+
+ exit-latency-us:
+ description:
+ The worst case latency in microseconds required to exit the idle
+ state.
+
+ min-residency-us:
+ description:
+ The minimum residency duration in microseconds after which the idle
+ state will yield power benefits, after overcoming the overhead while
+ entering the idle state.
+
+ required:
+ - compatible
+ - entry-latency-us
+ - exit-latency-us
+ - min-residency-us
+
+additionalProperties: false
+
+examples:
+ - |
+ idle-states {
+ CPU_SPC: spc {
+ compatible = "qcom,idle-state-spc", "arm,idle-state";
+ entry-latency-us = <150>;
+ exit-latency-us = <200>;
+ min-residency-us = <2000>;
+ };
+ };
Switched maintainer from Lina to Bjorn. Doesn't fix: ``` idle-states: 'spc' does not match any of the regexes: '^(cpu|cluster)-', 'pinctrl-[0-9]+' ``` from colliding arm/idle-states.yaml . Signed-off-by: David Heidelberg <david@ixit.cz> --- v2 - maintainer is now Bjorn - fixed some newlines - specified exact state names (added $) .../bindings/arm/msm/qcom,idle-state.txt | 84 ------------ .../bindings/arm/msm/qcom,idle-state.yaml | 126 ++++++++++++++++++ 2 files changed, 126 insertions(+), 84 deletions(-) delete mode 100644 Documentation/devicetree/bindings/arm/msm/qcom,idle-state.txt create mode 100644 Documentation/devicetree/bindings/arm/msm/qcom,idle-state.yaml