@@ -18,6 +18,7 @@
#include <linux/phylink.h>
#include <linux/gpio/consumer.h>
#include <linux/etherdevice.h>
+#include <linux/leds.h>
#include "qca8k.h"
@@ -950,6 +951,467 @@ qca8k_setup_of_rgmii_delay(struct qca8k_priv *priv)
return 0;
}
+static int
+qca8k_get_enable_led_reg(int port_num, int led_num, struct qca8k_led_pattern_en *reg_info)
+{
+ int shift;
+
+ switch (port_num) {
+ case 0:
+ reg_info->reg = QCA8K_LED_CTRL_REG(led_num);
+ reg_info->shift = 14;
+ break;
+ case 1:
+ case 2:
+ case 3:
+ reg_info->reg = QCA8K_LED_CTRL_REG(3);
+ shift = 2 * led_num + (6 * (port_num - 1));
+
+ reg_info->shift = 8 + shift;
+
+ break;
+ case 4:
+ reg_info->reg = QCA8K_LED_CTRL_REG(led_num);
+ reg_info->shift = 30;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int
+qca8k_get_control_led_reg(int port_num, int led_num, struct qca8k_led_pattern_en *reg_info)
+{
+ reg_info->reg = QCA8K_LED_CTRL_REG(led_num);
+
+ /* 6 total control rule:
+ * 3 control rules for phy0-3 that applies to all their leds
+ * 3 control rules for phy4
+ */
+ if (port_num == 4)
+ reg_info->shift = 16;
+ else
+ reg_info->shift = 0;
+
+ return 0;
+}
+
+static int
+qca8k_setup_led_rules(struct qca8k_led *led, struct fwnode_handle *node)
+{
+ struct qca8k_led_pattern_en reg_info;
+ const char **rules;
+ int i, count, ret;
+ const char *rule;
+ u32 val = 0;
+
+ if (!fwnode_property_present(node, "qca,led_rules"))
+ return 0;
+
+ rules = kcalloc(QCA8K_LED_RULE_MAX, sizeof(*rules), GFP_KERNEL);
+ if (!rules)
+ return -ENOMEM;
+
+ ret = fwnode_property_read_string_array(node, "qca,led_rules", rules, QCA8K_LED_RULE_MAX);
+ if (ret < 0)
+ return ret;
+
+ count = (unsigned int)ret;
+
+ for (i = 0; i < count; i++) {
+ rule = rules[i];
+
+ if (!strcmp(rule, "tx-blink"))
+ val |= QCA8K_LED_TX_BLINK_MASK;
+
+ if (!strcmp(rule, "rx-blink"))
+ val |= QCA8K_LED_RX_BLINK_MASK;
+
+ if (!strcmp(rule, "collision-blink"))
+ val |= QCA8K_LED_COL_BLINK_MASK;
+
+ if (!strcmp(rule, "link-10M"))
+ val |= QCA8K_LED_LINK_10M_EN_MASK;
+
+ if (!strcmp(rule, "link-100M"))
+ val |= QCA8K_LED_LINK_100M_EN_MASK;
+
+ if (!strcmp(rule, "link-1000M"))
+ val |= QCA8K_LED_LINK_1000M_EN_MASK;
+
+ if (!strcmp(rule, "half-duplex"))
+ val |= QCA8K_LED_HALF_DUPLEX_MASK;
+
+ if (!strcmp(rule, "full-duplex"))
+ val |= QCA8K_LED_FULL_DUPLEX_MASK;
+
+ if (!strcmp(rule, "linkup-over"))
+ val |= QCA8K_LED_LINKUP_OVER_MASK;
+
+ if (!strcmp(rule, "power-on-reset"))
+ val |= QCA8K_LED_POWER_ON_LIGHT_MASK;
+
+ if (!(val & QCA8K_LED_BLINK_FREQ_MASK)) {
+ if (!strcmp(rule, "blink-2hz"))
+ val |= QCA8K_LED_BLINK_2HZ << QCA8K_LED_BLINK_FREQ_SHITF;
+ else if (!strcmp(rule, "blink-4hz"))
+ val |= QCA8K_LED_BLINK_4HZ << QCA8K_LED_BLINK_FREQ_SHITF;
+ else if (!strcmp(rule, "blink-8hz"))
+ val |= QCA8K_LED_BLINK_8HZ << QCA8K_LED_BLINK_FREQ_SHITF;
+ else if (!strcmp(rule, "blink-auto"))
+ val |= QCA8K_LED_BLINK_AUTO << QCA8K_LED_BLINK_FREQ_SHITF;
+ }
+ }
+
+ kfree(rules);
+
+ qca8k_get_control_led_reg(led->port_num, led->led_num, ®_info);
+
+ ret = qca8k_rmw(led->priv, reg_info.reg,
+ QCA8K_LED_CTRL_MASK << reg_info.shift,
+ val << reg_info.shift);
+
+ return ret;
+}
+
+static ssize_t
+control_rule_show(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ struct led_classdev *led_cdev = dev_get_drvdata(dev);
+ struct qca8k_led *led = container_of(led_cdev, struct qca8k_led, cdev);
+ struct qca8k_led_pattern_en reg_info;
+ u32 value;
+ int ret;
+
+ qca8k_get_control_led_reg(led->port_num, led->led_num, ®_info);
+
+ ret = qca8k_read(led->priv, reg_info.reg, &value);
+ if (ret)
+ return sprintf(buf, "Error reading control rule\n");
+
+ value >>= reg_info.shift;
+ value &= QCA8K_LED_CTRL_MASK;
+
+ return sprintf(buf, "%x\n", value);
+}
+
+static ssize_t
+control_rule_store(struct device *dev,
+ struct device_attribute *attr, const char *buf,
+ size_t size)
+{
+ struct led_classdev *led_cdev = dev_get_drvdata(dev);
+ struct qca8k_led *led = container_of(led_cdev, struct qca8k_led, cdev);
+ struct qca8k_led_pattern_en reg_info;
+ ssize_t status;
+ long value;
+ int ret;
+
+ status = kstrtol(buf, 0, &value);
+ if (status)
+ return status;
+
+ if (value < 0)
+ return -EINVAL;
+
+ qca8k_get_control_led_reg(led->port_num, led->led_num, ®_info);
+
+ value &= QCA8K_LED_CTRL_MASK;
+
+ ret = qca8k_rmw(led->priv, reg_info.reg,
+ QCA8K_LED_CTRL_MASK << reg_info.shift,
+ value << reg_info.shift);
+ if (ret)
+ return ret;
+
+ return size;
+}
+
+static ssize_t
+hw_mode_show(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ struct led_classdev *led_cdev = dev_get_drvdata(dev);
+ struct qca8k_led *led = container_of(led_cdev, struct qca8k_led, cdev);
+ struct qca8k_led_pattern_en reg_info;
+ u32 value;
+ int ret;
+
+ qca8k_get_enable_led_reg(led->port_num, led->led_num, ®_info);
+
+ ret = qca8k_read(led->priv, reg_info.reg, &value);
+ if (ret)
+ return sprintf(buf, "Error reading hw mode\n");
+
+ value >>= reg_info.shift;
+ value &= GENMASK(1, 0);
+
+ return sprintf(buf, "%x\n", value == QCA8K_LED_RULE_CONTROLLED ? 1 : 0);
+}
+
+static ssize_t
+hw_mode_store(struct device *dev,
+ struct device_attribute *attr, const char *buf,
+ size_t size)
+{
+ struct led_classdev *led_cdev = dev_get_drvdata(dev);
+ struct qca8k_led *led = container_of(led_cdev, struct qca8k_led, cdev);
+ struct qca8k_led_pattern_en reg_info;
+ ssize_t status;
+ long value;
+ int ret;
+
+ status = kstrtol(buf, 0, &value);
+ if (status)
+ return status;
+
+ if (value < 0)
+ return -EINVAL;
+
+ qca8k_get_enable_led_reg(led->port_num, led->led_num, ®_info);
+
+ if (value)
+ value = QCA8K_LED_RULE_CONTROLLED;
+
+ value &= GENMASK(1, 0);
+
+ ret = qca8k_rmw(led->priv, reg_info.reg,
+ GENMASK(1, 0) << reg_info.shift,
+ value << reg_info.shift);
+ if (ret)
+ return ret;
+
+ return size;
+}
+
+static DEVICE_ATTR_RW(control_rule);
+static DEVICE_ATTR_RW(hw_mode);
+
+/* Each led have a enable hw_mode and optionally a way to set control rule */
+static struct attribute *qca8k_leds_attrs[] = {
+ &dev_attr_hw_mode.attr,
+ &dev_attr_control_rule.attr,
+ NULL,
+};
+
+static struct attribute_group qca8k_leds_rule_group = {
+ .attrs = qca8k_leds_attrs,
+};
+
+static const struct attribute_group *qca8k_leds_groups[] = {
+ &qca8k_leds_rule_group,
+ NULL,
+};
+
+static void
+qca8k_led_brightness_set(struct qca8k_led *led,
+ enum led_brightness b)
+{
+ struct qca8k_led_pattern_en reg_info;
+ u32 val = QCA8K_LED_ALWAYS_OFF;
+
+ qca8k_get_enable_led_reg(led->port_num, led->led_num, ®_info);
+
+ if (b)
+ val = QCA8K_LED_ALWAYS_ON;
+
+ qca8k_rmw(led->priv, reg_info.reg,
+ GENMASK(1, 0) << reg_info.shift,
+ val << reg_info.shift);
+}
+
+static void
+qca8k_cled_brightness_set(struct led_classdev *ldev,
+ enum led_brightness b)
+{
+ struct qca8k_led *led = container_of(ldev, struct qca8k_led, cdev);
+
+ return qca8k_led_brightness_set(led, b);
+}
+
+static enum led_brightness
+qca8k_led_brightness_get(struct qca8k_led *led)
+{
+ struct qca8k_led_pattern_en reg_info;
+ u32 val;
+ int ret;
+
+ qca8k_get_enable_led_reg(led->port_num, led->led_num, ®_info);
+
+ ret = qca8k_read(led->priv, reg_info.reg, &val);
+ if (ret)
+ return 0;
+
+ val >>= reg_info.shift;
+ val &= GENMASK(1, 0);
+
+ return val > 0 ? 1 : 0;
+}
+
+static enum led_brightness
+qca8k_cled_brightness_get(struct led_classdev *ldev)
+{
+ struct qca8k_led *led = container_of(ldev, struct qca8k_led, cdev);
+
+ return qca8k_led_brightness_get(led);
+}
+
+static int
+qca8k_cled_blink_set(struct led_classdev *ldev,
+ unsigned long *delay_on,
+ unsigned long *delay_off)
+{
+ struct qca8k_led *led = container_of(ldev, struct qca8k_led, cdev);
+ struct qca8k_led_pattern_en reg_info;
+
+ if (*delay_on == 0 && *delay_off == 0) {
+ *delay_on = 125;
+ *delay_off = 125;
+ }
+
+ if (*delay_on != 125 || *delay_off != 125) {
+ /* The hardware only supports blinking at 4Hz. Fall back
+ * to software implementation in other cases.
+ */
+ return -EINVAL;
+ }
+
+ qca8k_get_enable_led_reg(led->port_num, led->led_num, ®_info);
+
+ qca8k_rmw(led->priv, reg_info.reg,
+ GENMASK(1, 0) << reg_info.shift,
+ QCA8K_LED_ALWAYS_BLINK_4HZ << reg_info.shift);
+
+ return 0;
+}
+
+static void
+qca8k_cled_flash_resume(struct led_classdev *ldev)
+{
+ struct qca8k_led *led = container_of(ldev, struct qca8k_led, cdev);
+ struct qca8k_led_pattern_en reg_info;
+
+ qca8k_get_enable_led_reg(led->port_num, led->led_num, ®_info);
+ qca8k_rmw(led->priv, reg_info.reg,
+ GENMASK(1, 0) << reg_info.shift,
+ led->old_pattern << reg_info.shift);
+}
+
+static int
+qca8k_parse_port_leds(struct qca8k_priv *priv, struct fwnode_handle *port, int port_num)
+{
+ struct led_init_data init_data = { };
+ struct fwnode_handle *led = NULL;
+ struct qca8k_led *port_led;
+ int led_num, port_index;
+ const char *state;
+ int ret;
+
+ fwnode_for_each_child_node(port, led) {
+ /* Reg rapresent the led number of the port.
+ * Each port can have at least 3 leds attached
+ * Commonly:
+ * 1. is gigabit led
+ * 2. is mbit led
+ * 3. additional status led
+ */
+ if (fwnode_property_read_u32(led, "reg", &led_num))
+ continue;
+
+ if (led_num >= QCA8K_LED_PORT_COUNT) {
+ dev_warn(priv->dev, "Invalid LED reg defined %d", port_num);
+ continue;
+ }
+
+ port_index = 3 * port_num + led_num;
+
+ port_led = &priv->ports_led[port_index];
+ port_led->port_num = port_num;
+ port_led->led_num = led_num;
+ port_led->priv = priv;
+
+ ret = fwnode_property_read_string(led, "default-state", &state);
+ if (!ret) {
+ if (!strcmp(state, "on")) {
+ port_led->cdev.brightness = 1;
+ qca8k_led_brightness_set(port_led, 1);
+ } else if (!strcmp(state, "off")) {
+ port_led->cdev.brightness = 0;
+ qca8k_led_brightness_set(port_led, 0);
+ } else if (!strcmp(state, "keep")) {
+ port_led->cdev.brightness =
+ qca8k_led_brightness_get(port_led);
+ }
+ }
+
+ /* 3 brightness settings can be applied from Documentation:
+ * 0 always off
+ * 1 blink at 4Hz
+ * 2 always on
+ * 3 rule controlled
+ * Suppots only 2 mode: (pcb limitation, with always on and blink
+ * only the last led is set to this mode)
+ * 0 always off (sets all leds off)
+ * 3 rule controlled
+ */
+ port_led->cdev.max_brightness = 1;
+ port_led->cdev.brightness_set = qca8k_cled_brightness_set;
+ port_led->cdev.brightness_get = qca8k_cled_brightness_get;
+ port_led->cdev.blink_set = qca8k_cled_blink_set;
+ port_led->cdev.flash_resume = qca8k_cled_flash_resume;
+ port_led->cdev.groups = qca8k_leds_groups;
+ port_led->cdev.flags |= LED_CORE_SUSPENDRESUME;
+ init_data.default_label = ":port";
+ init_data.devicename = "qca8k";
+ init_data.fwnode = led;
+
+ /* Provide control rule first lan port and wan port.
+ * Lan port 2-3-4 follow first lan port control rule if the hw mode
+ * is active.
+ * The control_rule sysfs refer to the same reg for lan port (phy0-3)
+ */
+ ret = qca8k_setup_led_rules(port_led, led);
+ if (ret)
+ dev_warn(priv->dev, "Failed to apply led control rules for %s",
+ port_led->cdev.name);
+
+ ret = devm_led_classdev_register_ext(priv->dev, &port_led->cdev, &init_data);
+ if (ret)
+ dev_warn(priv->dev, "Failed to int led");
+ }
+
+ return 0;
+}
+
+static int
+qca8k_setup_led_ctrl(struct qca8k_priv *priv)
+{
+ struct fwnode_handle *leds, *port;
+ int port_num;
+ int ret;
+
+ leds = device_get_named_child_node(priv->dev, "leds");
+ if (!leds) {
+ dev_info(priv->dev, "No LEDs specified in device tree!\n");
+ return 0;
+ }
+
+ fwnode_for_each_child_node(leds, port) {
+ if (fwnode_property_read_u32(port, "reg", &port_num))
+ continue;
+
+ /* Each port can have at least 3 different leds attached */
+ ret = qca8k_parse_port_leds(priv, port, port_num);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
static int
qca8k_setup(struct dsa_switch *ds)
{
@@ -979,6 +1441,10 @@ qca8k_setup(struct dsa_switch *ds)
if (ret)
return ret;
+ ret = qca8k_setup_led_ctrl(priv);
+ if (ret)
+ return ret;
+
/* Enable CPU Port */
ret = qca8k_reg_set(priv, QCA8K_REG_GLOBAL_FW_CTRL0,
QCA8K_GLOBAL_FW_CTRL0_CPU_PORT_EN);
@@ -1890,13 +2356,29 @@ qca8k_sw_remove(struct mdio_device *mdiodev)
static void
qca8k_set_pm(struct qca8k_priv *priv, int enable)
{
- int i;
+ struct qca8k_led_pattern_en reg_info;
+ int port, led, port_index;
+ u32 val;
- for (i = 0; i < QCA8K_NUM_PORTS; i++) {
- if (!priv->port_sts[i].enabled)
+ for (port = 0; port < QCA8K_NUM_PORTS; port++) {
+ /* Save leds state for current port */
+ for (led = 0; led < 3; led++) {
+ port_index = 3 * port + led;
+ qca8k_get_enable_led_reg(port, led, ®_info);
+
+ if (!enable) {
+ qca8k_read(priv, reg_info.reg, &val);
+ val >>= reg_info.shift;
+ val &= GENMASK(1, 0);
+
+ priv->ports_led[port_index].old_pattern = val;
+ }
+ }
+
+ if (!priv->port_sts[port].enabled)
continue;
- qca8k_port_set_status(priv, i, enable);
+ qca8k_port_set_status(priv, port, enable);
}
}
@@ -64,6 +64,42 @@
#define QCA8K_MDIO_MASTER_DATA_MASK GENMASK(15, 0)
#define QCA8K_MDIO_MASTER_MAX_PORTS 5
#define QCA8K_MDIO_MASTER_MAX_REG 32
+
+/* LED control register */
+#define QCA8K_LED_COUNT 15
+#define QCA8K_LED_PORT_COUNT 3
+#define QCA8K_LED_RULE_COUNT 6
+#define QCA8K_LED_RULE_MAX 11
+#define QCA8K_LED_CTRL_REG(_i) (0x050 + (_i) * 4)
+#define QCA8K_LED_CTRL0_REG 0x50
+#define QCA8K_LED_CTRL1_REG 0x54
+#define QCA8K_LED_CTRL2_REG 0x58
+#define QCA8K_LED_CTRL3_REG 0x5C
+#define QCA8K_LED_CTRL_SHIFT(_i) (((_i) % 2) * 16)
+#define QCA8K_LED_CTRL_MASK GENMASK(13, 0)
+#define QCA8K_LED_BLINK_FREQ_MASK GENMASK(1, 0)
+#define QCA8K_LED_BLINK_FREQ_SHITF 0
+#define QCA8K_LED_BLINK_2HZ 0
+#define QCA8K_LED_BLINK_4HZ 1
+#define QCA8K_LED_BLINK_8HZ 2
+#define QCA8K_LED_BLINK_AUTO 3
+#define QCA8K_LED_LINKUP_OVER_MASK BIT(2)
+#define QCA8K_LED_TX_BLINK_MASK BIT(4)
+#define QCA8K_LED_RX_BLINK_MASK BIT(5)
+#define QCA8K_LED_COL_BLINK_MASK BIT(7)
+#define QCA8K_LED_LINK_10M_EN_MASK BIT(8)
+#define QCA8K_LED_LINK_100M_EN_MASK BIT(9)
+#define QCA8K_LED_LINK_1000M_EN_MASK BIT(10)
+#define QCA8K_LED_POWER_ON_LIGHT_MASK BIT(11)
+#define QCA8K_LED_HALF_DUPLEX_MASK BIT(12)
+#define QCA8K_LED_FULL_DUPLEX_MASK BIT(13)
+#define QCA8K_LED_PATTERN_EN_MASK GENMASK(15, 14)
+#define QCA8K_LED_PATTERN_EN_SHIFT 14
+#define QCA8K_LED_ALWAYS_OFF 0
+#define QCA8K_LED_ALWAYS_BLINK_4HZ 1
+#define QCA8K_LED_ALWAYS_ON 2
+#define QCA8K_LED_RULE_CONTROLLED 3
+
#define QCA8K_GOL_MAC_ADDR0 0x60
#define QCA8K_GOL_MAC_ADDR1 0x64
#define QCA8K_MAX_FRAME_SIZE 0x78
@@ -250,6 +286,19 @@ struct qca8k_match_data {
u8 id;
};
+struct qca8k_led_pattern_en {
+ u32 reg;
+ u8 shift;
+};
+
+struct qca8k_led {
+ u8 port_num;
+ u8 led_num;
+ u8 old_pattern;
+ struct qca8k_priv *priv;
+ struct led_classdev cdev;
+};
+
struct qca8k_priv {
u8 switch_id;
u8 switch_revision;
@@ -265,6 +314,7 @@ struct qca8k_priv {
struct dsa_switch_ops ops;
struct gpio_desc *reset_gpio;
unsigned int port_mtu[QCA8K_NUM_PORTS];
+ struct qca8k_led ports_led[QCA8K_LED_COUNT];
};
struct qca8k_mib_desc {
Add support for led control and led toggle. qca8337 and qca8327 switch have various reg to control port leds. The current implementation permit to toggle them on/off and to declare their blink rules based on the entry in the dts. They can also be declared in userspace by the "control_rule" entry in the led sysfs. When hw_mode is active (set by default) the leds blink based on the control_rule. There are 6 total control rule. Control rule that applies to phy0-3 commonly used for lan port. Control rule that applies to phy4 commonly used for wan port. Each phy port (5 in total) can have a maximum of 3 different leds attached. Each led can be turned off, blink at 4hz, off or set to hw_mode and follow their respecitve control rule. The hw_mode can be toggled using the sysfs entry and will be disabled on brightness or blink set. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> --- drivers/net/dsa/qca8k.c | 490 +++++++++++++++++++++++++++++++++++++++- drivers/net/dsa/qca8k.h | 50 ++++ 2 files changed, 536 insertions(+), 4 deletions(-)