diff mbox series

[v7,4/6] dt-bindings: mvebu-uart: update information about UART clock

Message ID 20210930095838.28145-5-pali@kernel.org (mailing list archive)
State New, archived
Headers show
Series serial: mvebu-uart: Support for higher baudrates | expand

Commit Message

Pali Rohár Sept. 30, 2021, 9:58 a.m. UTC 
Device "marvell,armada-3700-uart" should use
"marvell,armada-3700-uart-clock" compatible clock.

Signed-off-by: Pali Rohár <pali@kernel.org>
---
 Documentation/devicetree/bindings/serial/mvebu-uart.txt | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)

Comments

Rob Herring Oct. 6, 2021, 9:11 p.m. UTC | #1 
On Thu, Sep 30, 2021 at 4:59 AM Pali Rohár <pali@kernel.org> wrote:
>
> Device "marvell,armada-3700-uart" should use
> "marvell,armada-3700-uart-clock" compatible clock.
>
> Signed-off-by: Pali Rohár <pali@kernel.org>
> ---
>  Documentation/devicetree/bindings/serial/mvebu-uart.txt | 9 ++++++---
>  1 file changed, 6 insertions(+), 3 deletions(-)

Reviewed-by: Rob Herring <robh@kernel.org>
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/serial/mvebu-uart.txt b/Documentation/devicetree/bindings/serial/mvebu-uart.txt
index 2d0dbdf32d1d..a062bbca532c 100644
--- a/Documentation/devicetree/bindings/serial/mvebu-uart.txt
+++ b/Documentation/devicetree/bindings/serial/mvebu-uart.txt
@@ -14,7 +14,10 @@  Required properties:
       is provided (possible only with the "marvell,armada-3700-uart"
       compatible string for backward compatibility), it will only work
       if the baudrate was initialized by the bootloader and no baudrate
-      change will then be possible.
+      change will then be possible. When provided it should be UART1-clk
+      for standard variant of UART and UART2-clk for extended variant
+      of UART. TBG clock (with UART TBG divisors d1=d2=1) or xtal clock
+      should not be used and are supported only for backward compatibility.
 - interrupts:
     - Must contain three elements for the standard variant of the IP
       (marvell,armada-3700-uart): "uart-sum", "uart-tx" and "uart-rx",
@@ -34,7 +37,7 @@  Example:
 	uart0: serial@12000 {
 		compatible = "marvell,armada-3700-uart";
 		reg = <0x12000 0x18>;
-		clocks = <&xtalclk>;
+		clocks = <&uartclk 0>;
 		interrupts =
 		<GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
 		<GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
@@ -45,7 +48,7 @@  Example:
 	uart1: serial@12200 {
 		compatible = "marvell,armada-3700-uart-ext";
 		reg = <0x12200 0x30>;
-		clocks = <&xtalclk>;
+		clocks = <&uartclk 1>;
 		interrupts =
 		<GIC_SPI 30 IRQ_TYPE_EDGE_RISING>,
 		<GIC_SPI 31 IRQ_TYPE_EDGE_RISING>;