@@ -70,6 +70,7 @@ config NET_DSA_QCA8K
config NET_DSA_REALTEK_SMI
tristate "Realtek SMI Ethernet switch family support"
select NET_DSA_TAG_RTL4_A
+ select NET_DSA_TAG_RTL8_4
select FIXED_PHY
select IRQ_DOMAIN
select REALTEK_PHY
@@ -10,7 +10,7 @@ obj-$(CONFIG_NET_DSA_MT7530) += mt7530.o
obj-$(CONFIG_NET_DSA_MV88E6060) += mv88e6060.o
obj-$(CONFIG_NET_DSA_QCA8K) += qca8k.o
obj-$(CONFIG_NET_DSA_REALTEK_SMI) += realtek-smi.o
-realtek-smi-objs := realtek-smi-core.o rtl8366.o rtl8366rb.o
+realtek-smi-objs := realtek-smi-core.o rtl8366.o rtl8366rb.o rtl8365mb.o
obj-$(CONFIG_NET_DSA_SMSC_LAN9303) += lan9303-core.o
obj-$(CONFIG_NET_DSA_SMSC_LAN9303_I2C) += lan9303_i2c.o
obj-$(CONFIG_NET_DSA_SMSC_LAN9303_MDIO) += lan9303_mdio.o
@@ -501,6 +501,10 @@ static const struct of_device_id realtek_smi_of_match[] = {
.compatible = "realtek,rtl8366s",
.data = NULL,
},
+ {
+ .compatible = "realtek,rtl8365mb",
+ .data = &rtl8365mb_variant,
+ },
{ /* sentinel */ },
};
MODULE_DEVICE_TABLE(of, realtek_smi_of_match);
@@ -140,5 +140,6 @@ int rtl8366_get_sset_count(struct dsa_switch *ds, int port, int sset);
void rtl8366_get_ethtool_stats(struct dsa_switch *ds, int port, uint64_t *data);
extern const struct realtek_smi_variant rtl8366rb_variant;
+extern const struct realtek_smi_variant rtl8365mb_variant;
#endif /* _REALTEK_SMI_H */
new file mode 100644
@@ -0,0 +1,1981 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Realtek SMI subdriver for the Realtek RTL8365MB-VC ethernet switch.
+ *
+ * Copyright (C) 2021 Alvin Šipraga <alsi@bang-olufsen.dk>
+ * Copyright (C) 2021 Michael Rasmussen <mir@bang-olufsen.dk>
+ *
+ * The RTL8365MB-VC is a 4+1 port 10/100/1000M switch controller. It includes 4
+ * integrated PHYs for the user facing ports, and an extension interface which
+ * can be connected to the CPU - or another PHY - via either MII, RMII, or
+ * RGMII. The switch is configured via the Realtek Simple Management Interface
+ * (SMI), which uses the MDIO/MDC lines.
+ *
+ * Below is a simplified block diagram of the chip and its relevant interfaces.
+ *
+ * .-----------------------------------.
+ * | |
+ * UTP <---------------> Giga PHY <-> PCS <-> P0 GMAC |
+ * UTP <---------------> Giga PHY <-> PCS <-> P1 GMAC |
+ * UTP <---------------> Giga PHY <-> PCS <-> P2 GMAC |
+ * UTP <---------------> Giga PHY <-> PCS <-> P3 GMAC |
+ * | |
+ * CPU/PHY <-MII/RMII/RGMII---> Extension <---> Extension |
+ * | interface 1 GMAC 1 |
+ * | |
+ * SMI driver/ <-MDC/SCL---> Management ~~~~~~~~~~~~~~ |
+ * EEPROM <-MDIO/SDA--> interface ~REALTEK ~~~~~ |
+ * | ~RTL8365MB ~~~ |
+ * | ~GXXXC TAIWAN~ |
+ * GPIO <--------------> Reset ~~~~~~~~~~~~~~ |
+ * | |
+ * Interrupt <----------> Link UP/DOWN events |
+ * controller | |
+ * '-----------------------------------'
+ *
+ * The driver uses DSA to integrate the 4 user and 1 extension ports into the
+ * kernel. Netdevices are created for the user ports, as are PHY devices for
+ * their integrated PHYs. The device tree firmware should also specify the link
+ * partner of the extension port - either via a fixed-link or other phy-handle.
+ * See the device tree bindings for more detailed information. Note that the
+ * driver has only been tested with a fixed-link, but in principle it should not
+ * matter.
+ *
+ * NOTE: Currently, only the RGMII interface is implemented in this driver.
+ *
+ * The interrupt line is asserted on link UP/DOWN events. The driver creates a
+ * custom irqchip to handle this interrupt and demultiplex the events by reading
+ * the status registers via SMI. Interrupts are then propagated to the relevant
+ * PHY device.
+ *
+ * The EEPROM contains initial register values which the chip will read over I2C
+ * upon hardware reset. It is also possible to omit the EEPROM. In both cases,
+ * the driver will manually reprogram some registers using jam tables to reach
+ * an initial state defined by the vendor driver.
+ *
+ * This Linux driver is written based on an OS-agnostic vendor driver from
+ * Realtek. The reference GPL-licensed sources can be found in the OpenWrt
+ * source tree under the name rtl8367c. The vendor driver claims to support a
+ * number of similar switch controllers from Realtek, but the only hardware we
+ * have is the RTL8365MB-VC. Moreover, there does not seem to be any chip under
+ * the name RTL8367C. Although one wishes that the 'C' stood for some kind of
+ * common hardware revision, there exist examples of chips with the suffix -VC
+ * which are explicitly not supported by the rtl8367c driver and which instead
+ * require the rtl8367d vendor driver. With all this uncertainty, the driver has
+ * been modestly named rtl8365mb. Future implementors may wish to rename things
+ * accordingly.
+ *
+ * In the same family of chips, some carry up to 8 user ports and up to 2
+ * extension ports. Where possible this driver tries to make things generic, but
+ * more work must be done to support these configurations. According to
+ * documentation from Realtek, the family should include the following chips:
+ *
+ * - RTL8363NB
+ * - RTL8363NB-VB
+ * - RTL8363SC
+ * - RTL8363SC-VB
+ * - RTL8364NB
+ * - RTL8364NB-VB
+ * - RTL8365MB-VC
+ * - RTL8366SC
+ * - RTL8367RB-VB
+ * - RTL8367SB
+ * - RTL8367S
+ * - RTL8370MB
+ * - RTL8310SR
+ *
+ * Some of the register logic for these additional chips has been skipped over
+ * while implementing this driver. It is therefore not possible to assume that
+ * things will work out-of-the-box for other chips, and a careful review of the
+ * vendor driver may be needed to expand support. The RTL8365MB-VC seems to be
+ * one of the simpler chips.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bitops.h>
+#include <linux/interrupt.h>
+#include <linux/irqdomain.h>
+#include <linux/of_irq.h>
+#include <linux/regmap.h>
+#include <linux/if_bridge.h>
+
+#include "realtek-smi-core.h"
+
+/* Chip-specific data and limits */
+#define RTL8365MB_CHIP_ID_8365MB_VC 0x6367
+#define RTL8365MB_CPU_PORT_NUM_8365MB_VC 6
+#define RTL8365MB_LEARN_LIMIT_MAX_8365MB_VC 2112
+
+/* Family-specific data and limits */
+#define RTL8365MB_NUM_PHYREGS 32
+#define RTL8365MB_PHYREGMAX (RTL8365MB_NUM_PHYREGS - 1)
+#define RTL8365MB_MAX_NUM_PORTS (RTL8365MB_CPU_PORT_NUM_8365MB_VC + 1)
+
+/* Chip identification registers */
+#define RTL8365MB_CHIP_ID_REG 0x1300
+
+#define RTL8365MB_CHIP_VER_REG 0x1301
+
+#define RTL8365MB_MAGIC_REG 0x13C2
+#define RTL8365MB_MAGIC_VALUE 0x0249
+
+/* Chip reset register */
+#define RTL8365MB_CHIP_RESET_REG 0x1322
+#define RTL8365MB_CHIP_RESET_SW_MASK 0x0002
+#define RTL8365MB_CHIP_RESET_HW_MASK 0x0001
+
+/* Interrupt polarity register */
+#define RTL8365MB_INTR_POLARITY_REG 0x1100
+#define RTL8365MB_INTR_POLARITY_MASK 0x0001
+#define RTL8365MB_INTR_POLARITY_HIGH 0
+#define RTL8365MB_INTR_POLARITY_LOW 1
+
+/* Interrupt control/status register - enable/check specific interrupt types */
+#define RTL8365MB_INTR_CTRL_REG 0x1101
+#define RTL8365MB_INTR_STATUS_REG 0x1102
+#define RTL8365MB_INTR_SLIENT_START_2_MASK 0x1000
+#define RTL8365MB_INTR_SLIENT_START_MASK 0x0800
+#define RTL8365MB_INTR_ACL_ACTION_MASK 0x0200
+#define RTL8365MB_INTR_CABLE_DIAG_FIN_MASK 0x0100
+#define RTL8365MB_INTR_INTERRUPT_8051_MASK 0x0080
+#define RTL8365MB_INTR_LOOP_DETECTION_MASK 0x0040
+#define RTL8365MB_INTR_GREEN_TIMER_MASK 0x0020
+#define RTL8365MB_INTR_SPECIAL_CONGEST_MASK 0x0010
+#define RTL8365MB_INTR_SPEED_CHANGE_MASK 0x0008
+#define RTL8365MB_INTR_LEARN_OVER_MASK 0x0004
+#define RTL8365MB_INTR_METER_EXCEEDED_MASK 0x0002
+#define RTL8365MB_INTR_LINK_CHANGE_MASK 0x0001
+#define RTL8365MB_INTR_ALL_MASK \
+ (RTL8365MB_INTR_SLIENT_START_2_MASK | \
+ RTL8365MB_INTR_SLIENT_START_MASK | \
+ RTL8365MB_INTR_ACL_ACTION_MASK | \
+ RTL8365MB_INTR_CABLE_DIAG_FIN_MASK | \
+ RTL8365MB_INTR_INTERRUPT_8051_MASK | \
+ RTL8365MB_INTR_LOOP_DETECTION_MASK | \
+ RTL8365MB_INTR_GREEN_TIMER_MASK | \
+ RTL8365MB_INTR_SPECIAL_CONGEST_MASK | \
+ RTL8365MB_INTR_SPEED_CHANGE_MASK | \
+ RTL8365MB_INTR_LEARN_OVER_MASK | \
+ RTL8365MB_INTR_METER_EXCEEDED_MASK | \
+ RTL8365MB_INTR_LINK_CHANGE_MASK)
+
+/* Per-port interrupt type status registers */
+#define RTL8365MB_PORT_LINKDOWN_IND_REG 0x1106
+#define RTL8365MB_PORT_LINKDOWN_IND_MASK 0x07FF
+
+#define RTL8365MB_PORT_LINKUP_IND_REG 0x1107
+#define RTL8365MB_PORT_LINKUP_IND_MASK 0x07FF
+
+/* PHY indirect access registers */
+#define RTL8365MB_INDIRECT_ACCESS_CTRL_REG 0x1F00
+#define RTL8365MB_INDIRECT_ACCESS_CTRL_RW_MASK 0x0002
+#define RTL8365MB_INDIRECT_ACCESS_CTRL_RW_READ 0
+#define RTL8365MB_INDIRECT_ACCESS_CTRL_RW_WRITE 1
+#define RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_MASK 0x0001
+#define RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_VALUE 1
+#define RTL8365MB_INDIRECT_ACCESS_STATUS_REG 0x1F01
+#define RTL8365MB_INDIRECT_ACCESS_ADDRESS_REG 0x1F02
+#define RTL8365MB_INDIRECT_ACCESS_ADDRESS_OCPADR_5_1_MASK GENMASK(4, 0)
+#define RTL8365MB_INDIRECT_ACCESS_ADDRESS_PHYNUM_MASK GENMASK(6, 5)
+#define RTL8365MB_INDIRECT_ACCESS_ADDRESS_OCPADR_9_6_MASK GENMASK(11, 8)
+#define RTL8365MB_PHY_BASE 0x2000
+#define RTL8365MB_INDIRECT_ACCESS_WRITE_DATA_REG 0x1F03
+#define RTL8365MB_INDIRECT_ACCESS_READ_DATA_REG 0x1F04
+
+/* PHY OCP address prefix register */
+#define RTL8365MB_GPHY_OCP_MSB_0_REG 0x1D15
+#define RTL8365MB_GPHY_OCP_MSB_0_CFG_CPU_OCPADR_MASK 0x0FC0
+#define RTL8365MB_PHY_OCP_ADDR_PREFIX_MASK 0xFC00
+
+/* The PHY OCP addresses of PHY registers 0~31 start here */
+#define RTL8365MB_PHY_OCP_ADDR_PHYREG_BASE 0xA400
+
+/* EXT port interface mode values - used in DIGITAL_INTERFACE_SELECT */
+#define RTL8365MB_EXT_PORT_MODE_DISABLE 0
+#define RTL8365MB_EXT_PORT_MODE_RGMII 1
+#define RTL8365MB_EXT_PORT_MODE_MII_MAC 2
+#define RTL8365MB_EXT_PORT_MODE_MII_PHY 3
+#define RTL8365MB_EXT_PORT_MODE_TMII_MAC 4
+#define RTL8365MB_EXT_PORT_MODE_TMII_PHY 5
+#define RTL8365MB_EXT_PORT_MODE_GMII 6
+#define RTL8365MB_EXT_PORT_MODE_RMII_MAC 7
+#define RTL8365MB_EXT_PORT_MODE_RMII_PHY 8
+#define RTL8365MB_EXT_PORT_MODE_SGMII 9
+#define RTL8365MB_EXT_PORT_MODE_HSGMII 10
+#define RTL8365MB_EXT_PORT_MODE_1000X_100FX 11
+#define RTL8365MB_EXT_PORT_MODE_1000X 12
+#define RTL8365MB_EXT_PORT_MODE_100FX 13
+
+/* EXT port interface mode configuration registers 0~1 */
+#define RTL8365MB_DIGITAL_INTERFACE_SELECT_REG0 0x1305
+#define RTL8365MB_DIGITAL_INTERFACE_SELECT_REG1 0x13C3
+#define RTL8365MB_DIGITAL_INTERFACE_SELECT_REG(_extport) \
+ (RTL8365MB_DIGITAL_INTERFACE_SELECT_REG0 + \
+ ((_extport) >> 1) * (0x13C3 - 0x1305))
+#define RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_MASK(_extport) \
+ (0xF << (((_extport) % 2)))
+#define RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_OFFSET(_extport) \
+ (((_extport) % 2) * 4)
+
+/* EXT port RGMII TX/RX delay configuration registers 1~2 */
+#define RTL8365MB_EXT_RGMXF_REG1 0x1307
+#define RTL8365MB_EXT_RGMXF_REG2 0x13C5
+#define RTL8365MB_EXT_RGMXF_REG(_extport) \
+ (RTL8365MB_EXT_RGMXF_REG1 + \
+ (((_extport) >> 1) * (0x13C5 - 0x1307)))
+#define RTL8365MB_EXT_RGMXF_RXDELAY_MASK 0x0007
+#define RTL8365MB_EXT_RGMXF_TXDELAY_MASK 0x0008
+
+/* External port speed values - used in DIGITAL_INTERFACE_FORCE */
+#define RTL8365MB_PORT_SPEED_10M 0
+#define RTL8365MB_PORT_SPEED_100M 1
+#define RTL8365MB_PORT_SPEED_1000M 2
+
+/* EXT port force configuration registers 0~2 */
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG0 0x1310
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG1 0x1311
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG2 0x13C4
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG(_extport) \
+ (RTL8365MB_DIGITAL_INTERFACE_FORCE_REG0 + \
+ ((_extport) & 0x1) + \
+ ((((_extport) >> 1) & 0x1) * (0x13C4 - 0x1310)))
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_EN_MASK 0x1000
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_NWAY_MASK 0x0080
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_TXPAUSE_MASK 0x0040
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_RXPAUSE_MASK 0x0020
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_LINK_MASK 0x0010
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_DUPLEX_MASK 0x0004
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_SPEED_MASK 0x0003
+
+/* CPU port mask register - controls which ports are treated as CPU ports */
+#define RTL8365MB_CPU_PORT_MASK_REG 0x1219
+#define RTL8365MB_CPU_PORT_MASK_MASK 0x07FF
+
+/* CPU control register */
+#define RTL8365MB_CPU_CTRL_REG 0x121A
+#define RTL8365MB_CPU_CTRL_TRAP_PORT_EXT_MASK 0x0400
+#define RTL8365MB_CPU_CTRL_TAG_FORMAT_MASK 0x0200
+#define RTL8365MB_CPU_CTRL_RXBYTECOUNT_MASK 0x0080
+#define RTL8365MB_CPU_CTRL_TAG_POSITION_MASK 0x0040
+#define RTL8365MB_CPU_CTRL_TRAP_PORT_MASK 0x0038
+#define RTL8365MB_CPU_CTRL_INSERTMODE_MASK 0x0006
+#define RTL8365MB_CPU_CTRL_EN_MASK 0x0001
+
+/* Maximum packet length register */
+#define RTL8365MB_CFG0_MAX_LEN_REG 0x088C
+#define RTL8365MB_CFG0_MAX_LEN_MASK 0x3FFF
+
+/* Port learning limit registers */
+#define RTL8365MB_LUT_PORT_LEARN_LIMIT_BASE 0x0A20
+#define RTL8365MB_LUT_PORT_LEARN_LIMIT_REG(_physport) \
+ (RTL8365MB_LUT_PORT_LEARN_LIMIT_BASE + (_physport))
+
+/* Port isolation (forwarding mask) registers */
+#define RTL8365MB_PORT_ISOLATION_REG_BASE 0x08A2
+#define RTL8365MB_PORT_ISOLATION_REG(_physport) \
+ (RTL8365MB_PORT_ISOLATION_REG_BASE + (_physport))
+#define RTL8365MB_PORT_ISOLATION_MASK 0x07FF
+
+/* MSTP port state registers - indexed by tree instancrSTI (tree ine */
+#define RTL8365MB_MSTI_CTRL_BASE 0x0A00
+#define RTL8365MB_MSTI_CTRL_REG(_msti, _physport) \
+ (RTL8365MB_MSTI_CTRL_BASE + ((_msti) << 1) + ((_physport) >> 3))
+#define RTL8365MB_MSTI_CTRL_PORT_STATE_OFFSET(_physport) ((_physport) << 1)
+#define RTL8365MB_MSTI_CTRL_PORT_STATE_MASK(_physport) \
+ (0x3 << RTL8365MB_MSTI_CTRL_PORT_STATE_OFFSET((_physport)))
+
+/* MIB counter value registers */
+#define RTL8365MB_MIB_COUNTER_BASE 0x1000
+#define RTL8365MB_MIB_COUNTER_REG(_x) (RTL8365MB_MIB_COUNTER_BASE + (_x))
+
+/* MIB counter address register */
+#define RTL8365MB_MIB_ADDRESS_REG 0x1004
+#define RTL8365MB_MIB_ADDRESS_PORT_OFFSET 0x007C
+#define RTL8365MB_MIB_ADDRESS(_p, _x) \
+ (((RTL8365MB_MIB_ADDRESS_PORT_OFFSET) * (_p) + (_x)) >> 2)
+
+#define RTL8365MB_MIB_CTRL0_REG 0x1005
+#define RTL8365MB_MIB_CTRL0_RESET_MASK 0x0002
+#define RTL8365MB_MIB_CTRL0_BUSY_MASK 0x0001
+
+/* The DSA callback .get_stats64 runs in atomic context, so we are not allowed
+ * to sleep. On the other hand, accessing MIB counters absolutely requires us to
+ * sleep. The solution is thus to schedule work which polls the MIB counters
+ * asynchronously and updates some private data, which the callback can then
+ * fetch atomically. Three seconds should be a good enough polling interval.
+ */
+#define RTL8365MB_STATS_INTERVAL_JIFFIES (3 * HZ)
+
+enum rtl8365mb_mib_counter_index {
+ RTL8365MB_MIB_ifInOctets,
+ RTL8365MB_MIB_dot3StatsFCSErrors,
+ RTL8365MB_MIB_dot3StatsSymbolErrors,
+ RTL8365MB_MIB_dot3InPauseFrames,
+ RTL8365MB_MIB_dot3ControlInUnknownOpcodes,
+ RTL8365MB_MIB_etherStatsFragments,
+ RTL8365MB_MIB_etherStatsJabbers,
+ RTL8365MB_MIB_ifInUcastPkts,
+ RTL8365MB_MIB_etherStatsDropEvents,
+ RTL8365MB_MIB_ifInMulticastPkts,
+ RTL8365MB_MIB_ifInBroadcastPkts,
+ RTL8365MB_MIB_inMldChecksumError,
+ RTL8365MB_MIB_inIgmpChecksumError,
+ RTL8365MB_MIB_inMldSpecificQuery,
+ RTL8365MB_MIB_inMldGeneralQuery,
+ RTL8365MB_MIB_inIgmpSpecificQuery,
+ RTL8365MB_MIB_inIgmpGeneralQuery,
+ RTL8365MB_MIB_inMldLeaves,
+ RTL8365MB_MIB_inIgmpLeaves,
+ RTL8365MB_MIB_etherStatsOctets,
+ RTL8365MB_MIB_etherStatsUnderSizePkts,
+ RTL8365MB_MIB_etherOversizeStats,
+ RTL8365MB_MIB_etherStatsPkts64Octets,
+ RTL8365MB_MIB_etherStatsPkts65to127Octets,
+ RTL8365MB_MIB_etherStatsPkts128to255Octets,
+ RTL8365MB_MIB_etherStatsPkts256to511Octets,
+ RTL8365MB_MIB_etherStatsPkts512to1023Octets,
+ RTL8365MB_MIB_etherStatsPkts1024to1518Octets,
+ RTL8365MB_MIB_ifOutOctets,
+ RTL8365MB_MIB_dot3StatsSingleCollisionFrames,
+ RTL8365MB_MIB_dot3StatsMultipleCollisionFrames,
+ RTL8365MB_MIB_dot3StatsDeferredTransmissions,
+ RTL8365MB_MIB_dot3StatsLateCollisions,
+ RTL8365MB_MIB_etherStatsCollisions,
+ RTL8365MB_MIB_dot3StatsExcessiveCollisions,
+ RTL8365MB_MIB_dot3OutPauseFrames,
+ RTL8365MB_MIB_ifOutDiscards,
+ RTL8365MB_MIB_dot1dTpPortInDiscards,
+ RTL8365MB_MIB_ifOutUcastPkts,
+ RTL8365MB_MIB_ifOutMulticastPkts,
+ RTL8365MB_MIB_ifOutBroadcastPkts,
+ RTL8365MB_MIB_outOampduPkts,
+ RTL8365MB_MIB_inOampduPkts,
+ RTL8365MB_MIB_inIgmpJoinsSuccess,
+ RTL8365MB_MIB_inIgmpJoinsFail,
+ RTL8365MB_MIB_inMldJoinsSuccess,
+ RTL8365MB_MIB_inMldJoinsFail,
+ RTL8365MB_MIB_inReportSuppressionDrop,
+ RTL8365MB_MIB_inLeaveSuppressionDrop,
+ RTL8365MB_MIB_outIgmpReports,
+ RTL8365MB_MIB_outIgmpLeaves,
+ RTL8365MB_MIB_outIgmpGeneralQuery,
+ RTL8365MB_MIB_outIgmpSpecificQuery,
+ RTL8365MB_MIB_outMldReports,
+ RTL8365MB_MIB_outMldLeaves,
+ RTL8365MB_MIB_outMldGeneralQuery,
+ RTL8365MB_MIB_outMldSpecificQuery,
+ RTL8365MB_MIB_inKnownMulticastPkts,
+ RTL8365MB_MIB_END,
+};
+
+struct rtl8365mb_mib_counter {
+ u32 offset;
+ u32 length;
+ const char *name;
+};
+
+#define RTL8365MB_MAKE_MIB_COUNTER(_offset, _length, _name) \
+ [RTL8365MB_MIB_ ## _name] = { _offset, _length, #_name }
+
+static struct rtl8365mb_mib_counter rtl8365mb_mib_counters[] = {
+ RTL8365MB_MAKE_MIB_COUNTER(0, 4, ifInOctets),
+ RTL8365MB_MAKE_MIB_COUNTER(4, 2, dot3StatsFCSErrors),
+ RTL8365MB_MAKE_MIB_COUNTER(6, 2, dot3StatsSymbolErrors),
+ RTL8365MB_MAKE_MIB_COUNTER(8, 2, dot3InPauseFrames),
+ RTL8365MB_MAKE_MIB_COUNTER(10, 2, dot3ControlInUnknownOpcodes),
+ RTL8365MB_MAKE_MIB_COUNTER(12, 2, etherStatsFragments),
+ RTL8365MB_MAKE_MIB_COUNTER(14, 2, etherStatsJabbers),
+ RTL8365MB_MAKE_MIB_COUNTER(16, 2, ifInUcastPkts),
+ RTL8365MB_MAKE_MIB_COUNTER(18, 2, etherStatsDropEvents),
+ RTL8365MB_MAKE_MIB_COUNTER(20, 2, ifInMulticastPkts),
+ RTL8365MB_MAKE_MIB_COUNTER(22, 2, ifInBroadcastPkts),
+ RTL8365MB_MAKE_MIB_COUNTER(24, 2, inMldChecksumError),
+ RTL8365MB_MAKE_MIB_COUNTER(26, 2, inIgmpChecksumError),
+ RTL8365MB_MAKE_MIB_COUNTER(28, 2, inMldSpecificQuery),
+ RTL8365MB_MAKE_MIB_COUNTER(30, 2, inMldGeneralQuery),
+ RTL8365MB_MAKE_MIB_COUNTER(32, 2, inIgmpSpecificQuery),
+ RTL8365MB_MAKE_MIB_COUNTER(34, 2, inIgmpGeneralQuery),
+ RTL8365MB_MAKE_MIB_COUNTER(36, 2, inMldLeaves),
+ RTL8365MB_MAKE_MIB_COUNTER(38, 2, inIgmpLeaves),
+ RTL8365MB_MAKE_MIB_COUNTER(40, 4, etherStatsOctets),
+ RTL8365MB_MAKE_MIB_COUNTER(44, 2, etherStatsUnderSizePkts),
+ RTL8365MB_MAKE_MIB_COUNTER(46, 2, etherOversizeStats),
+ RTL8365MB_MAKE_MIB_COUNTER(48, 2, etherStatsPkts64Octets),
+ RTL8365MB_MAKE_MIB_COUNTER(50, 2, etherStatsPkts65to127Octets),
+ RTL8365MB_MAKE_MIB_COUNTER(52, 2, etherStatsPkts128to255Octets),
+ RTL8365MB_MAKE_MIB_COUNTER(54, 2, etherStatsPkts256to511Octets),
+ RTL8365MB_MAKE_MIB_COUNTER(56, 2, etherStatsPkts512to1023Octets),
+ RTL8365MB_MAKE_MIB_COUNTER(58, 2, etherStatsPkts1024to1518Octets),
+ RTL8365MB_MAKE_MIB_COUNTER(60, 4, ifOutOctets),
+ RTL8365MB_MAKE_MIB_COUNTER(64, 2, dot3StatsSingleCollisionFrames),
+ RTL8365MB_MAKE_MIB_COUNTER(66, 2, dot3StatsMultipleCollisionFrames),
+ RTL8365MB_MAKE_MIB_COUNTER(68, 2, dot3StatsDeferredTransmissions),
+ RTL8365MB_MAKE_MIB_COUNTER(70, 2, dot3StatsLateCollisions),
+ RTL8365MB_MAKE_MIB_COUNTER(72, 2, etherStatsCollisions),
+ RTL8365MB_MAKE_MIB_COUNTER(74, 2, dot3StatsExcessiveCollisions),
+ RTL8365MB_MAKE_MIB_COUNTER(76, 2, dot3OutPauseFrames),
+ RTL8365MB_MAKE_MIB_COUNTER(78, 2, ifOutDiscards),
+ RTL8365MB_MAKE_MIB_COUNTER(80, 2, dot1dTpPortInDiscards),
+ RTL8365MB_MAKE_MIB_COUNTER(82, 2, ifOutUcastPkts),
+ RTL8365MB_MAKE_MIB_COUNTER(84, 2, ifOutMulticastPkts),
+ RTL8365MB_MAKE_MIB_COUNTER(86, 2, ifOutBroadcastPkts),
+ RTL8365MB_MAKE_MIB_COUNTER(88, 2, outOampduPkts),
+ RTL8365MB_MAKE_MIB_COUNTER(90, 2, inOampduPkts),
+ RTL8365MB_MAKE_MIB_COUNTER(92, 4, inIgmpJoinsSuccess),
+ RTL8365MB_MAKE_MIB_COUNTER(96, 2, inIgmpJoinsFail),
+ RTL8365MB_MAKE_MIB_COUNTER(98, 2, inMldJoinsSuccess),
+ RTL8365MB_MAKE_MIB_COUNTER(100, 2, inMldJoinsFail),
+ RTL8365MB_MAKE_MIB_COUNTER(102, 2, inReportSuppressionDrop),
+ RTL8365MB_MAKE_MIB_COUNTER(104, 2, inLeaveSuppressionDrop),
+ RTL8365MB_MAKE_MIB_COUNTER(106, 2, outIgmpReports),
+ RTL8365MB_MAKE_MIB_COUNTER(108, 2, outIgmpLeaves),
+ RTL8365MB_MAKE_MIB_COUNTER(110, 2, outIgmpGeneralQuery),
+ RTL8365MB_MAKE_MIB_COUNTER(112, 2, outIgmpSpecificQuery),
+ RTL8365MB_MAKE_MIB_COUNTER(114, 2, outMldReports),
+ RTL8365MB_MAKE_MIB_COUNTER(116, 2, outMldLeaves),
+ RTL8365MB_MAKE_MIB_COUNTER(118, 2, outMldGeneralQuery),
+ RTL8365MB_MAKE_MIB_COUNTER(120, 2, outMldSpecificQuery),
+ RTL8365MB_MAKE_MIB_COUNTER(122, 2, inKnownMulticastPkts),
+};
+
+static_assert(ARRAY_SIZE(rtl8365mb_mib_counters) == RTL8365MB_MIB_END);
+
+struct rtl8365mb_jam_tbl_entry {
+ u16 reg;
+ u16 val;
+};
+
+/* Lifted from the vendor driver sources */
+static const struct rtl8365mb_jam_tbl_entry rtl8365mb_init_jam_8365mb_vc[] = {
+ { 0x13EB, 0x15BB }, { 0x1303, 0x06D6 }, { 0x1304, 0x0700 },
+ { 0x13E2, 0x003F }, { 0x13F9, 0x0090 }, { 0x121E, 0x03CA },
+ { 0x1233, 0x0352 }, { 0x1237, 0x00A0 }, { 0x123A, 0x0030 },
+ { 0x1239, 0x0084 }, { 0x0301, 0x1000 }, { 0x1349, 0x001F },
+ { 0x18E0, 0x4004 }, { 0x122B, 0x241C }, { 0x1305, 0xC000 },
+ { 0x13F0, 0x0000 },
+};
+
+static const struct rtl8365mb_jam_tbl_entry rtl8365mb_init_jam_common[] = {
+ { 0x1200, 0x7FCB }, { 0x0884, 0x0003 }, { 0x06EB, 0x0001 },
+ { 0x03Fa, 0x0007 }, { 0x08C8, 0x00C0 }, { 0x0A30, 0x020E },
+ { 0x0800, 0x0000 }, { 0x0802, 0x0000 }, { 0x09DA, 0x0013 },
+ { 0x1D32, 0x0002 },
+};
+
+enum rtl8365mb_stp_state {
+ RTL8365MB_STP_STATE_DISABLED = 0,
+ RTL8365MB_STP_STATE_BLOCKING = 1,
+ RTL8365MB_STP_STATE_LEARNING = 2,
+ RTL8365MB_STP_STATE_FORWARDING = 3,
+};
+
+enum rtl8365mb_cpu_insert {
+ RTL8365MB_CPU_INSERT_TO_ALL = 0,
+ RTL8365MB_CPU_INSERT_TO_TRAPPING = 1,
+ RTL8365MB_CPU_INSERT_TO_NONE = 2,
+};
+
+enum rtl8365mb_cpu_position {
+ RTL8365MB_CPU_POS_AFTER_SA = 0,
+ RTL8365MB_CPU_POS_BEFORE_CRC = 1,
+};
+
+enum rtl8365mb_cpu_format {
+ RTL8365MB_CPU_FORMAT_8BYTES = 0,
+ RTL8365MB_CPU_FORMAT_4BYTES = 1,
+};
+
+enum rtl8365mb_cpu_rxlen {
+ RTL8365MB_CPU_RXLEN_72BYTES = 0,
+ RTL8365MB_CPU_RXLEN_64BYTES = 1,
+};
+
+/**
+ * struct rtl8365mb_cpu - CPU port configuration
+ * @enable: enable/disable hardware insertion of CPU tag in switch->CPU frames
+ * @mask: port mask of ports that parse should parse CPU tags
+ * @trap_port: forward trapped frames to this port
+ * @insert: CPU tag insertion mode in switch->CPU frames
+ * @position: position of CPU tag in frame
+ * @rx_length: minimum CPU RX length
+ * @format: CPU tag format
+ *
+ * Represents the CPU tagging and CPU port configuration of the switch. These
+ * settings are configurable at runtime.
+ */
+struct rtl8365mb_cpu {
+ bool enable;
+ u32 mask;
+ u32 trap_port;
+ enum rtl8365mb_cpu_insert insert;
+ enum rtl8365mb_cpu_position position;
+ enum rtl8365mb_cpu_rxlen rx_length;
+ enum rtl8365mb_cpu_format format;
+};
+
+/**
+ * struct rtl8365mb_port - private per-port data
+ * @smi: pointer to parent realtek_smi data
+ * @index: DSA port index, same as dsa_port::index
+ * @stats: link statistics populated by rtl8365mb_stats_poll, ready for atomic
+ * access via rtl8365mb_get_stats64
+ * @stats_lock: spinlock to protect the stats structure during read/update
+ * @mib_work: delayed work for polling MIB counters
+ */
+struct rtl8365mb_port {
+ struct realtek_smi *smi;
+ unsigned int index;
+ struct rtnl_link_stats64 stats;
+ spinlock_t stats_lock;
+ struct delayed_work mib_work;
+};
+
+/**
+ * struct rtl8365mb - private chip-specific driver data
+ * @smi: pointer to parent realtek_smi data
+ * @irq: registered IRQ or zero
+ * @chip_id: chip identifier
+ * @chip_ver: chip silicon revision
+ * @port_mask: mask of all ports
+ * @learn_limit_max: maximum number of L2 addresses the chip can learn
+ * @cpu: CPU tagging and CPU port configuration for this chip
+ * @mib_lock: spinlock to prevent concurrent reads of MIB counters
+ * @ports: per-port data
+ * @jam_table: chip-specific initialization jam table
+ * @jam_size: size of the chip's jam table
+ *
+ * Private data for this driver.
+ */
+struct rtl8365mb {
+ struct realtek_smi *smi;
+ int irq;
+ u32 chip_id;
+ u32 chip_ver;
+ u32 port_mask;
+ u32 learn_limit_max;
+ struct rtl8365mb_cpu cpu;
+ spinlock_t mib_lock;
+ struct rtl8365mb_port ports[RTL8365MB_MAX_NUM_PORTS];
+ const struct rtl8365mb_jam_tbl_entry *jam_table;
+ size_t jam_size;
+};
+
+static int rtl8365mb_phy_poll_busy(struct realtek_smi *smi)
+{
+ u32 val;
+
+ return regmap_read_poll_timeout(smi->map,
+ RTL8365MB_INDIRECT_ACCESS_STATUS_REG,
+ val, !val, 10, 100);
+}
+
+static int rtl8365mb_phy_ocp_prepare(struct realtek_smi *smi, int phy,
+ u32 ocp_addr)
+{
+ u32 val;
+ int ret;
+
+ /* Set OCP prefix */
+ val = FIELD_GET(RTL8365MB_PHY_OCP_ADDR_PREFIX_MASK, ocp_addr);
+ ret = regmap_update_bits(
+ smi->map, RTL8365MB_GPHY_OCP_MSB_0_REG,
+ RTL8365MB_GPHY_OCP_MSB_0_CFG_CPU_OCPADR_MASK,
+ FIELD_PREP(RTL8365MB_GPHY_OCP_MSB_0_CFG_CPU_OCPADR_MASK, val));
+ if (ret)
+ return ret;
+
+ /* Set PHY register address */
+ val = RTL8365MB_PHY_BASE;
+ val |= FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_ADDRESS_PHYNUM_MASK, phy);
+ val |= FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_ADDRESS_OCPADR_5_1_MASK,
+ ocp_addr >> 1);
+ val |= FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_ADDRESS_OCPADR_9_6_MASK,
+ ocp_addr >> 6);
+ ret = regmap_write(smi->map, RTL8365MB_INDIRECT_ACCESS_ADDRESS_REG,
+ val);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int rtl8365mb_phy_ocp_read(struct realtek_smi *smi, int phy,
+ u32 ocp_addr, u16 *data)
+{
+ u32 val;
+ int ret;
+
+ ret = rtl8365mb_phy_poll_busy(smi);
+ if (ret)
+ return ret;
+
+ ret = rtl8365mb_phy_ocp_prepare(smi, phy, ocp_addr);
+ if (ret)
+ return ret;
+
+ /* Execute read operation */
+ val = FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_MASK,
+ RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_VALUE) |
+ FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_CTRL_RW_MASK,
+ RTL8365MB_INDIRECT_ACCESS_CTRL_RW_READ);
+ ret = regmap_write(smi->map, RTL8365MB_INDIRECT_ACCESS_CTRL_REG, val);
+ if (ret)
+ return ret;
+
+ ret = rtl8365mb_phy_poll_busy(smi);
+ if (ret)
+ return ret;
+
+ /* Get PHY register data */
+ ret = regmap_read(smi->map, RTL8365MB_INDIRECT_ACCESS_READ_DATA_REG,
+ &val);
+ if (ret)
+ return ret;
+
+ *data = val & 0xFFFF;
+
+ return 0;
+}
+
+static int rtl8365mb_phy_ocp_write(struct realtek_smi *smi, int phy,
+ u32 ocp_addr, u16 data)
+{
+ u32 val;
+ int ret;
+
+ ret = rtl8365mb_phy_poll_busy(smi);
+ if (ret)
+ return ret;
+
+ ret = rtl8365mb_phy_ocp_prepare(smi, phy, ocp_addr);
+ if (ret)
+ return ret;
+
+ /* Set PHY register data */
+ ret = regmap_write(smi->map, RTL8365MB_INDIRECT_ACCESS_WRITE_DATA_REG,
+ data);
+ if (ret)
+ return ret;
+
+ /* Execute write operation */
+ val = FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_MASK,
+ RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_VALUE) |
+ FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_CTRL_RW_MASK,
+ RTL8365MB_INDIRECT_ACCESS_CTRL_RW_WRITE);
+ ret = regmap_write(smi->map, RTL8365MB_INDIRECT_ACCESS_CTRL_REG, val);
+ if (ret)
+ return ret;
+
+ ret = rtl8365mb_phy_poll_busy(smi);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int rtl8365mb_phy_read(struct realtek_smi *smi, int phy, int regnum)
+{
+ u32 ocp_addr;
+ u16 val;
+ int ret;
+
+ if (regnum > RTL8365MB_PHYREGMAX)
+ return -EINVAL;
+
+ ocp_addr = RTL8365MB_PHY_OCP_ADDR_PHYREG_BASE + regnum * 2;
+
+ ret = rtl8365mb_phy_ocp_read(smi, phy, ocp_addr, &val);
+ if (ret) {
+ dev_err(smi->dev,
+ "failed to read PHY%d reg %02x @ %04x, ret %d\n", phy,
+ regnum, ocp_addr, ret);
+ return ret;
+ }
+
+ dev_dbg(smi->dev, "read PHY%d register 0x%02x @ %04x, val <- %04x\n",
+ phy, regnum, ocp_addr, val);
+
+ return val;
+}
+
+static int rtl8365mb_phy_write(struct realtek_smi *smi, int phy, int regnum,
+ u16 val)
+{
+ u32 ocp_addr;
+ int ret;
+
+ if (regnum > RTL8365MB_PHYREGMAX)
+ return -EINVAL;
+
+ ocp_addr = RTL8365MB_PHY_OCP_ADDR_PHYREG_BASE + regnum * 2;
+
+ ret = rtl8365mb_phy_ocp_write(smi, phy, ocp_addr, val);
+ if (ret) {
+ dev_err(smi->dev,
+ "failed to write PHY%d reg %02x @ %04x, ret %d\n", phy,
+ regnum, ocp_addr, ret);
+ return ret;
+ }
+
+ dev_dbg(smi->dev, "write PHY%d register 0x%02x @ %04x, val -> %04x\n",
+ phy, regnum, ocp_addr, val);
+
+ return 0;
+}
+
+static enum dsa_tag_protocol
+rtl8365mb_get_tag_protocol(struct dsa_switch *ds, int port,
+ enum dsa_tag_protocol mp)
+{
+ return DSA_TAG_PROTO_RTL8_4;
+}
+
+static int rtl8365mb_ext_config_rgmii(struct realtek_smi *smi, int port,
+ phy_interface_t interface)
+{
+ struct device_node *dn;
+ struct dsa_port *dp;
+ int tx_delay = 0;
+ int rx_delay = 0;
+ int ext_port;
+ u32 val;
+ int ret;
+
+ if (port == smi->cpu_port) {
+ ext_port = 1;
+ } else {
+ dev_err(smi->dev, "only one EXT port is currently supported\n");
+ return -EINVAL;
+ }
+
+ dp = dsa_to_port(smi->ds, port);
+ dn = dp->dn;
+
+ /* Set the RGMII TX/RX delay
+ *
+ * The Realtek vendor driver indicates the following possible
+ * configuration settings:
+ *
+ * TX delay:
+ * 0 = no delay, 1 = 2 ns delay
+ * RX delay:
+ * 0 = no delay, 7 = maximum delay
+ * No units are specified, but there are a total of 8 steps.
+ *
+ * The vendor driver also states that this must be configured *before*
+ * forcing the external interface into a particular mode, which is done
+ * in the rtl8365mb_phylink_mac_link_{up,down} functions.
+ *
+ * Only configure an RGMII TX (resp. RX) delay if the
+ * tx-internal-delay-ps (resp. rx-internal-delay-ps) OF property is
+ * specified. We ignore the detail of the RGMII interface mode
+ * (RGMII_{RXID, TXID, etc.}), as this is considered to be a PHY-only
+ * property.
+ *
+ * For the RX delay, we assume that a register value of 4 corresponds to
+ * 2 ns. But this is just an educated guess, so ignore all other values
+ * to avoid too much confusion.
+ */
+ if (!of_property_read_u32(dn, "tx-internal-delay-ps", &val)) {
+ val = val / 1000; /* convert to ns */
+
+ if (val == 0 || val == 2)
+ tx_delay = val / 2;
+ else
+ dev_warn(smi->dev,
+ "EXT port TX delay must be 0 or 2 ns\n");
+ }
+
+ if (!of_property_read_u32(dn, "rx-internal-delay-ps", &val)) {
+ val = val / 1000; /* convert to ns */
+
+ if (val == 0 || val == 2)
+ rx_delay = val * 2;
+ else
+ dev_warn(smi->dev,
+ "EXT port RX delay must be 0 to 2 ns\n");
+ }
+
+ ret = regmap_update_bits(
+ smi->map, RTL8365MB_EXT_RGMXF_REG(ext_port),
+ RTL8365MB_EXT_RGMXF_TXDELAY_MASK |
+ RTL8365MB_EXT_RGMXF_RXDELAY_MASK,
+ FIELD_PREP(RTL8365MB_EXT_RGMXF_TXDELAY_MASK, tx_delay) |
+ FIELD_PREP(RTL8365MB_EXT_RGMXF_RXDELAY_MASK, rx_delay));
+ if (ret)
+ return ret;
+
+ ret = regmap_update_bits(
+ smi->map, RTL8365MB_DIGITAL_INTERFACE_SELECT_REG(ext_port),
+ RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_MASK(ext_port),
+ RTL8365MB_EXT_PORT_MODE_RGMII
+ << RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_OFFSET(
+ ext_port));
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int rtl8365mb_ext_config_forcemode(struct realtek_smi *smi, int port,
+ bool link, int speed, int duplex,
+ bool tx_pause, bool rx_pause)
+{
+ u32 r_tx_pause;
+ u32 r_rx_pause;
+ u32 r_duplex;
+ u32 r_speed;
+ u32 r_link;
+ int ext_port;
+ int val;
+ int ret;
+
+ if (port == smi->cpu_port) {
+ ext_port = 1;
+ } else {
+ dev_err(smi->dev, "only one EXT port is currently supported\n");
+ return -EINVAL;
+ }
+
+ if (link) {
+ /* Force the link up with the desired configuration */
+ r_link = 1;
+ r_rx_pause = rx_pause ? 1 : 0;
+ r_tx_pause = tx_pause ? 1 : 0;
+
+ if (speed == SPEED_1000) {
+ r_speed = RTL8365MB_PORT_SPEED_1000M;
+ } else if (speed == SPEED_100) {
+ r_speed = RTL8365MB_PORT_SPEED_100M;
+ } else if (speed == SPEED_10) {
+ r_speed = RTL8365MB_PORT_SPEED_10M;
+ } else {
+ dev_err(smi->dev, "unsupported port speed %s\n",
+ phy_speed_to_str(speed));
+ return -EINVAL;
+ }
+
+ if (duplex == DUPLEX_FULL) {
+ r_duplex = 1;
+ } else if (duplex == DUPLEX_HALF) {
+ r_duplex = 0;
+ } else {
+ dev_err(smi->dev, "unsupported duplex %s\n",
+ phy_duplex_to_str(duplex));
+ return -EINVAL;
+ }
+ } else {
+ /* Force the link down and reset any programmed configuration */
+ r_link = 0;
+ r_tx_pause = 0;
+ r_rx_pause = 0;
+ r_speed = 0;
+ r_duplex = 0;
+ }
+
+ val = FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_EN_MASK, 1) |
+ FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_TXPAUSE_MASK,
+ r_tx_pause) |
+ FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_RXPAUSE_MASK,
+ r_rx_pause) |
+ FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_LINK_MASK, r_link) |
+ FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_DUPLEX_MASK,
+ r_duplex) |
+ FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_SPEED_MASK, r_speed);
+ ret = regmap_write(smi->map,
+ RTL8365MB_DIGITAL_INTERFACE_FORCE_REG(ext_port),
+ val);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static bool rtl8365mb_phy_mode_supported(struct dsa_switch *ds, int port,
+ phy_interface_t interface)
+{
+ if (dsa_is_user_port(ds, port) &&
+ (interface == PHY_INTERFACE_MODE_NA ||
+ interface == PHY_INTERFACE_MODE_INTERNAL))
+ /* Internal PHY */
+ return true;
+ else if (dsa_is_cpu_port(ds, port) &&
+ phy_interface_mode_is_rgmii(interface))
+ /* Extension MAC */
+ return true;
+
+ return false;
+}
+
+static void rtl8365mb_phylink_validate(struct dsa_switch *ds, int port,
+ unsigned long *supported,
+ struct phylink_link_state *state)
+{
+ struct realtek_smi *smi = ds->priv;
+ __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0 };
+
+ /* include/linux/phylink.h says:
+ * When @state->interface is %PHY_INTERFACE_MODE_NA, phylink
+ * expects the MAC driver to return all supported link modes.
+ */
+ if (state->interface != PHY_INTERFACE_MODE_NA &&
+ !rtl8365mb_phy_mode_supported(ds, port, state->interface)) {
+ dev_err(smi->dev, "phy mode %s is unsupported on port %d\n",
+ phy_modes(state->interface), port);
+ linkmode_zero(supported);
+ return;
+ }
+
+ phylink_set_port_modes(mask);
+
+ phylink_set(mask, Autoneg);
+ phylink_set(mask, Pause);
+ phylink_set(mask, Asym_Pause);
+
+ phylink_set(mask, 10baseT_Half);
+ phylink_set(mask, 10baseT_Full);
+ phylink_set(mask, 100baseT_Half);
+ phylink_set(mask, 100baseT_Full);
+ phylink_set(mask, 1000baseT_Full);
+
+ linkmode_and(supported, supported, mask);
+ linkmode_and(state->advertising, state->advertising, mask);
+}
+
+static void rtl8365mb_phylink_mac_config(struct dsa_switch *ds, int port,
+ unsigned int mode,
+ const struct phylink_link_state *state)
+{
+ struct realtek_smi *smi = ds->priv;
+ int ret;
+
+ if (!rtl8365mb_phy_mode_supported(ds, port, state->interface)) {
+ dev_err(smi->dev, "phy mode %s is unsupported on port %d\n",
+ phy_modes(state->interface), port);
+ return;
+ }
+
+ if (mode != MLO_AN_PHY && mode != MLO_AN_FIXED) {
+ dev_err(smi->dev,
+ "port %d supports only conventional PHY or fixed-link\n",
+ port);
+ return;
+ }
+
+ if (phy_interface_mode_is_rgmii(state->interface)) {
+ ret = rtl8365mb_ext_config_rgmii(smi, port, state->interface);
+ if (ret)
+ dev_err(smi->dev,
+ "failed to configure RGMII mode on port %d: %d\n",
+ port, ret);
+ return;
+ }
+
+ /* TODO: Implement MII and RMII modes, which the RTL8365MB-VC also
+ * supports
+ */
+}
+
+static void rtl8365mb_phylink_mac_link_down(struct dsa_switch *ds, int port,
+ unsigned int mode,
+ phy_interface_t interface)
+{
+ struct realtek_smi *smi = ds->priv;
+ struct rtl8365mb_port *p;
+ struct rtl8365mb *mb;
+ int ret;
+
+ mb = smi->chip_data;
+ p = &mb->ports[port];
+ cancel_delayed_work_sync(&p->mib_work);
+
+ if (phy_interface_mode_is_rgmii(interface)) {
+ ret = rtl8365mb_ext_config_forcemode(smi, port, false, 0, 0,
+ false, false);
+ if (ret)
+ dev_err(smi->dev,
+ "failed to reset forced mode on port %d: %d\n",
+ port, ret);
+
+ return;
+ }
+}
+
+static void rtl8365mb_phylink_mac_link_up(struct dsa_switch *ds, int port,
+ unsigned int mode,
+ phy_interface_t interface,
+ struct phy_device *phydev, int speed,
+ int duplex, bool tx_pause,
+ bool rx_pause)
+{
+ struct realtek_smi *smi = ds->priv;
+ struct rtl8365mb_port *p;
+ struct rtl8365mb *mb;
+ int ret;
+
+ mb = smi->chip_data;
+ p = &mb->ports[port];
+ schedule_delayed_work(&p->mib_work, 0);
+
+ if (phy_interface_mode_is_rgmii(interface)) {
+ ret = rtl8365mb_ext_config_forcemode(smi, port, true, speed,
+ duplex, tx_pause,
+ rx_pause);
+ if (ret)
+ dev_err(smi->dev,
+ "failed to force mode on port %d: %d\n", port,
+ ret);
+
+ return;
+ }
+}
+
+static void rtl8365mb_port_stp_state_set(struct dsa_switch *ds, int port,
+ u8 state)
+{
+ struct realtek_smi *smi = ds->priv;
+ enum rtl8365mb_stp_state val;
+ int msti = 0;
+
+ switch (state) {
+ case BR_STATE_DISABLED:
+ val = RTL8365MB_STP_STATE_DISABLED;
+ break;
+ case BR_STATE_BLOCKING:
+ case BR_STATE_LISTENING:
+ val = RTL8365MB_STP_STATE_BLOCKING;
+ break;
+ case BR_STATE_LEARNING:
+ val = RTL8365MB_STP_STATE_LEARNING;
+ break;
+ case BR_STATE_FORWARDING:
+ val = RTL8365MB_STP_STATE_FORWARDING;
+ break;
+ default:
+ dev_err(smi->dev, "invalid STP state: %u\n", state);
+ return;
+ }
+
+ regmap_update_bits(smi->map, RTL8365MB_MSTI_CTRL_REG(msti, port),
+ RTL8365MB_MSTI_CTRL_PORT_STATE_MASK(port),
+ val << RTL8365MB_MSTI_CTRL_PORT_STATE_OFFSET(port));
+}
+
+static int rtl8365mb_port_set_learning(struct realtek_smi *smi, int port,
+ bool enable)
+{
+ struct rtl8365mb *mb = smi->chip_data;
+
+ /* Enable/disable learning by limiting the number of L2 addresses the
+ * port can learn. Realtek documentation states that a limit of zero
+ * disables learning. When enabling learning, set it to the chip's
+ * maximum.
+ */
+ return regmap_write(smi->map, RTL8365MB_LUT_PORT_LEARN_LIMIT_REG(port),
+ enable ? mb->learn_limit_max : 0);
+}
+
+static int rtl8365mb_port_set_isolation(struct realtek_smi *smi, int port,
+ u32 mask)
+{
+ return regmap_write(smi->map, RTL8365MB_PORT_ISOLATION_REG(port), mask);
+}
+
+static int rtl8365mb_mib_counter_read(struct realtek_smi *smi, int port,
+ u32 offset, u32 length, u64 *mibvalue)
+{
+ u64 tmpvalue = 0;
+ u32 val;
+ int ret;
+ int i;
+
+ /* The MIB address is an SRAM address. We request a particular address
+ * and then poll the control register before reading the value from some
+ * counter registers.
+ */
+ ret = regmap_write(smi->map, RTL8365MB_MIB_ADDRESS_REG,
+ RTL8365MB_MIB_ADDRESS(port, offset));
+ if (ret)
+ return ret;
+
+ /* Poll for completion */
+ ret = regmap_read_poll_timeout(smi->map, RTL8365MB_MIB_CTRL0_REG, val,
+ !(val & RTL8365MB_MIB_CTRL0_BUSY_MASK),
+ 10, 100);
+ if (ret)
+ return ret;
+
+ /* Presumably this indicates a MIB counter read failure */
+ if (val & RTL8365MB_MIB_CTRL0_RESET_MASK)
+ return -EIO;
+
+ /* There are four MIB counter registers each holding a 16 bit word of a
+ * MIB counter. Depending on the offset, we should read from the upper
+ * two or lower two registers. In case the MIB counter is 4 words, we
+ * read from all four registers.
+ */
+ if (length == 4)
+ offset = 3;
+ else
+ offset = (offset + 1) % 4;
+
+ /* Read the MIB counter 16 bits at a time */
+ for (i = 0; i < length; i++) {
+ ret = regmap_read(smi->map,
+ RTL8365MB_MIB_COUNTER_REG(offset - i), &val);
+ if (ret)
+ return ret;
+
+ tmpvalue = ((tmpvalue) << 16) | (val & 0xFFFF);
+ }
+
+ /* Only commit the result if no error occurred */
+ *mibvalue = tmpvalue;
+
+ return 0;
+}
+
+static void rtl8365mb_get_ethtool_stats(struct dsa_switch *ds, int port, u64 *data)
+{
+ struct realtek_smi *smi = ds->priv;
+ struct rtl8365mb *mb;
+ int ret;
+ int i;
+
+ mb = smi->chip_data;
+
+ spin_lock(&mb->mib_lock);
+ for (i = 0; i < RTL8365MB_MIB_END; i++) {
+ struct rtl8365mb_mib_counter *mib = &rtl8365mb_mib_counters[i];
+
+ ret = rtl8365mb_mib_counter_read(smi, port, mib->offset,
+ mib->length, &data[i]);
+ if (ret) {
+ dev_err(smi->dev,
+ "failed to read port %d counters: %d\n", port,
+ ret);
+ break;
+ }
+ }
+ spin_unlock(&mb->mib_lock);
+}
+
+static void rtl8365mb_get_strings(struct dsa_switch *ds, int port, u32 stringset, u8 *data)
+{
+ int i;
+
+ if (stringset != ETH_SS_STATS)
+ return;
+
+ for (i = 0; i < RTL8365MB_MIB_END; i++) {
+ struct rtl8365mb_mib_counter *mib = &rtl8365mb_mib_counters[i];
+
+ strncpy(data + i * ETH_GSTRING_LEN, mib->name, ETH_GSTRING_LEN);
+ }
+}
+
+static int rtl8365mb_get_sset_count(struct dsa_switch *ds, int port, int sset)
+{
+ if (sset != ETH_SS_STATS)
+ return -EOPNOTSUPP;
+
+ return RTL8365MB_MIB_END;
+}
+
+static void rtl8365mb_get_phy_stats(struct dsa_switch *ds, int port,
+ struct ethtool_eth_phy_stats *phy_stats)
+{
+ struct realtek_smi *smi = ds->priv;
+ struct rtl8365mb_mib_counter *mib;
+ struct rtl8365mb *mb;
+
+ mb = smi->chip_data;
+ mib = &rtl8365mb_mib_counters[RTL8365MB_MIB_dot3StatsSymbolErrors];
+
+ spin_lock(&mb->mib_lock);
+ rtl8365mb_mib_counter_read(smi, port, mib->offset, mib->length,
+ &phy_stats->SymbolErrorDuringCarrier);
+ spin_unlock(&mb->mib_lock);
+}
+
+static void rtl8365mb_get_mac_stats(struct dsa_switch *ds, int port,
+ struct ethtool_eth_mac_stats *mac_stats)
+{
+ u64 cnt[RTL8365MB_MIB_END] = {
+ [RTL8365MB_MIB_ifOutOctets] = 1,
+ [RTL8365MB_MIB_ifOutUcastPkts] = 1,
+ [RTL8365MB_MIB_ifOutMulticastPkts] = 1,
+ [RTL8365MB_MIB_ifOutBroadcastPkts] = 1,
+ [RTL8365MB_MIB_dot3OutPauseFrames] = 1,
+ [RTL8365MB_MIB_ifOutDiscards] = 1,
+ [RTL8365MB_MIB_ifInOctets] = 1,
+ [RTL8365MB_MIB_ifInUcastPkts] = 1,
+ [RTL8365MB_MIB_ifInMulticastPkts] = 1,
+ [RTL8365MB_MIB_ifInBroadcastPkts] = 1,
+ [RTL8365MB_MIB_dot3InPauseFrames] = 1,
+ [RTL8365MB_MIB_dot3StatsSingleCollisionFrames] = 1,
+ [RTL8365MB_MIB_dot3StatsMultipleCollisionFrames] = 1,
+ [RTL8365MB_MIB_dot3StatsFCSErrors] = 1,
+ [RTL8365MB_MIB_dot3StatsDeferredTransmissions] = 1,
+ [RTL8365MB_MIB_dot3StatsLateCollisions] = 1,
+ [RTL8365MB_MIB_dot3StatsExcessiveCollisions] = 1,
+
+ };
+ struct realtek_smi *smi = ds->priv;
+ struct rtl8365mb *mb;
+ int ret;
+ int i;
+
+ mb = smi->chip_data;
+
+ spin_lock(&mb->mib_lock);
+ for (i = 0; i < RTL8365MB_MIB_END; i++) {
+ struct rtl8365mb_mib_counter *mib = &rtl8365mb_mib_counters[i];
+
+ /* Only fetch required MIB counters (marked = 1 above) */
+ if (!cnt[i])
+ continue;
+
+ ret = rtl8365mb_mib_counter_read(smi, port, mib->offset,
+ mib->length, &cnt[i]);
+ if (ret)
+ break;
+ }
+ spin_unlock(&mb->mib_lock);
+
+ /* The RTL8365MB-VC exposes MIB objects, which we have to translate into
+ * IEEE 802.3 Managed Objects. This is not always completely faithful,
+ * but we try out best. See RFC 3635 for a detailed treatment of the
+ * subject.
+ */
+
+ mac_stats->FramesTransmittedOK = cnt[RTL8365MB_MIB_ifOutUcastPkts] +
+ cnt[RTL8365MB_MIB_ifOutMulticastPkts] +
+ cnt[RTL8365MB_MIB_ifOutBroadcastPkts] +
+ cnt[RTL8365MB_MIB_dot3OutPauseFrames] -
+ cnt[RTL8365MB_MIB_ifOutDiscards];
+ mac_stats->SingleCollisionFrames =
+ cnt[RTL8365MB_MIB_dot3StatsSingleCollisionFrames];
+ mac_stats->MultipleCollisionFrames =
+ cnt[RTL8365MB_MIB_dot3StatsMultipleCollisionFrames];
+ mac_stats->FramesReceivedOK = cnt[RTL8365MB_MIB_ifInUcastPkts] +
+ cnt[RTL8365MB_MIB_ifInMulticastPkts] +
+ cnt[RTL8365MB_MIB_ifInBroadcastPkts] +
+ cnt[RTL8365MB_MIB_dot3InPauseFrames];
+ mac_stats->FrameCheckSequenceErrors =
+ cnt[RTL8365MB_MIB_dot3StatsFCSErrors];
+ mac_stats->OctetsTransmittedOK = cnt[RTL8365MB_MIB_ifOutOctets] -
+ 18 * mac_stats->FramesTransmittedOK;
+ mac_stats->FramesWithDeferredXmissions =
+ cnt[RTL8365MB_MIB_dot3StatsDeferredTransmissions];
+ mac_stats->LateCollisions = cnt[RTL8365MB_MIB_dot3StatsLateCollisions];
+ mac_stats->FramesAbortedDueToXSColls =
+ cnt[RTL8365MB_MIB_dot3StatsExcessiveCollisions];
+ mac_stats->OctetsReceivedOK = cnt[RTL8365MB_MIB_ifInOctets] -
+ 18 * mac_stats->FramesReceivedOK;
+ mac_stats->MulticastFramesXmittedOK =
+ cnt[RTL8365MB_MIB_ifOutMulticastPkts];
+ mac_stats->BroadcastFramesXmittedOK =
+ cnt[RTL8365MB_MIB_ifOutBroadcastPkts];
+ mac_stats->MulticastFramesReceivedOK =
+ cnt[RTL8365MB_MIB_ifInMulticastPkts];
+ mac_stats->BroadcastFramesReceivedOK =
+ cnt[RTL8365MB_MIB_ifInBroadcastPkts];
+}
+
+static void rtl8365mb_get_ctrl_stats(struct dsa_switch *ds, int port,
+ struct ethtool_eth_ctrl_stats *ctrl_stats)
+{
+ struct realtek_smi *smi = ds->priv;
+ struct rtl8365mb_mib_counter *mib;
+ struct rtl8365mb *mb;
+
+ mb = smi->chip_data;
+ mib = &rtl8365mb_mib_counters[RTL8365MB_MIB_dot3ControlInUnknownOpcodes];
+
+ spin_lock(&mb->mib_lock);
+ rtl8365mb_mib_counter_read(smi, port, mib->offset, mib->length,
+ &ctrl_stats->UnsupportedOpcodesReceived);
+ spin_unlock(&mb->mib_lock);
+}
+
+static void rtl8365mb_stats_update(struct realtek_smi *smi, int port)
+{
+ u64 cnt[RTL8365MB_MIB_END] = {
+ [RTL8365MB_MIB_ifOutOctets] = 1,
+ [RTL8365MB_MIB_ifOutUcastPkts] = 1,
+ [RTL8365MB_MIB_ifOutMulticastPkts] = 1,
+ [RTL8365MB_MIB_ifOutBroadcastPkts] = 1,
+ [RTL8365MB_MIB_ifOutDiscards] = 1,
+ [RTL8365MB_MIB_ifInOctets] = 1,
+ [RTL8365MB_MIB_ifInUcastPkts] = 1,
+ [RTL8365MB_MIB_ifInMulticastPkts] = 1,
+ [RTL8365MB_MIB_ifInBroadcastPkts] = 1,
+ [RTL8365MB_MIB_etherStatsDropEvents] = 1,
+ [RTL8365MB_MIB_etherStatsCollisions] = 1,
+ [RTL8365MB_MIB_etherStatsFragments] = 1,
+ [RTL8365MB_MIB_etherStatsJabbers] = 1,
+ [RTL8365MB_MIB_dot3StatsFCSErrors] = 1,
+ [RTL8365MB_MIB_dot3StatsLateCollisions] = 1,
+ };
+ struct rtl8365mb *mb = smi->chip_data;
+ struct rtnl_link_stats64 *stats;
+ int ret;
+ int i;
+
+ stats = &mb->ports[port].stats;
+
+ spin_lock(&mb->mib_lock);
+ for (i = 0; i < RTL8365MB_MIB_END; i++) {
+ struct rtl8365mb_mib_counter *c = &rtl8365mb_mib_counters[i];
+
+ /* Only fetch required MIB counters (marked = 1 above) */
+ if (!cnt[i])
+ continue;
+
+ ret = rtl8365mb_mib_counter_read(smi, port, c->offset,
+ c->length, &cnt[i]);
+ if (ret)
+ break;
+ }
+ spin_unlock(&mb->mib_lock);
+
+ /* Don't update statistics if there was an error reading the counters */
+ if (ret)
+ return;
+
+ spin_lock(&mb->ports[port].stats_lock);
+
+ stats->rx_packets = cnt[RTL8365MB_MIB_ifInUcastPkts] +
+ cnt[RTL8365MB_MIB_ifInMulticastPkts] +
+ cnt[RTL8365MB_MIB_ifInBroadcastPkts] -
+ cnt[RTL8365MB_MIB_ifOutDiscards];
+
+ stats->tx_packets = cnt[RTL8365MB_MIB_ifOutUcastPkts] +
+ cnt[RTL8365MB_MIB_ifOutMulticastPkts] +
+ cnt[RTL8365MB_MIB_ifOutBroadcastPkts];
+
+ /* if{In,Out}Octets includes FCS - remove it */
+ stats->rx_bytes = cnt[RTL8365MB_MIB_ifInOctets] - 4 * stats->rx_packets;
+ stats->tx_bytes =
+ cnt[RTL8365MB_MIB_ifOutOctets] - 4 * stats->tx_packets;
+
+ stats->rx_dropped = cnt[RTL8365MB_MIB_etherStatsDropEvents];
+ stats->tx_dropped = cnt[RTL8365MB_MIB_ifOutDiscards];
+
+ stats->multicast = cnt[RTL8365MB_MIB_ifInMulticastPkts];
+ stats->collisions = cnt[RTL8365MB_MIB_etherStatsCollisions];
+
+ stats->rx_length_errors = cnt[RTL8365MB_MIB_etherStatsFragments] +
+ cnt[RTL8365MB_MIB_etherStatsJabbers];
+ stats->rx_crc_errors = cnt[RTL8365MB_MIB_dot3StatsFCSErrors];
+ stats->rx_errors = stats->rx_length_errors + stats->rx_crc_errors;
+
+ stats->tx_aborted_errors = cnt[RTL8365MB_MIB_ifOutDiscards];
+ stats->tx_window_errors = cnt[RTL8365MB_MIB_dot3StatsLateCollisions];
+ stats->tx_errors = stats->tx_aborted_errors + stats->tx_window_errors;
+
+ spin_unlock(&mb->ports[port].stats_lock);
+}
+
+static void rtl8365mb_stats_poll(struct work_struct *work)
+{
+ struct rtl8365mb_port *p = container_of(to_delayed_work(work),
+ struct rtl8365mb_port,
+ mib_work);
+ struct realtek_smi *smi = p->smi;
+
+ rtl8365mb_stats_update(smi, p->index);
+
+ schedule_delayed_work(&p->mib_work, RTL8365MB_STATS_INTERVAL_JIFFIES);
+}
+
+static void rtl8365mb_get_stats64(struct dsa_switch *ds, int port,
+ struct rtnl_link_stats64 *s)
+{
+ struct realtek_smi *smi = ds->priv;
+ struct rtl8365mb_port *p;
+ struct rtl8365mb *mb;
+
+ mb = smi->chip_data;
+ p = &mb->ports[port];
+
+ spin_lock(&p->stats_lock);
+ memcpy(s, &p->stats, sizeof(*s));
+ spin_unlock(&p->stats_lock);
+}
+
+static void rtl8365mb_stats_setup(struct realtek_smi *smi)
+{
+ struct rtl8365mb *mb = smi->chip_data;
+ int i;
+
+ /* Per-chip global spinlock to protect MIB counter access, since doing
+ * so requires accessing a series of registers in a particular order.
+ */
+ spin_lock_init(&mb->mib_lock);
+
+ for (i = 0; i < smi->num_ports; i++) {
+ struct rtl8365mb_port *p = &mb->ports[i];
+
+ if (dsa_is_unused_port(smi->ds, i))
+ continue;
+
+ /* Per-port spinlock to protect the stats64 data */
+ spin_lock_init(&p->stats_lock);
+
+ /* This work polls the MIB counters and keeps the stats64 data
+ * up-to-date.
+ */
+ INIT_DELAYED_WORK(&p->mib_work, rtl8365mb_stats_poll);
+ }
+}
+
+static void rtl8365mb_stats_teardown(struct realtek_smi *smi)
+{
+ struct rtl8365mb *mb = smi->chip_data;
+ int i;
+
+ for (i = 0; i < smi->num_ports; i++) {
+ struct rtl8365mb_port *p = &mb->ports[i];
+
+ if (dsa_is_unused_port(smi->ds, i))
+ continue;
+
+ cancel_delayed_work_sync(&p->mib_work);
+ }
+}
+
+static int rtl8365mb_get_and_clear_status_reg(struct realtek_smi *smi, u32 reg,
+ u32 *val)
+{
+ int ret;
+
+ ret = regmap_read(smi->map, reg, val);
+ if (ret)
+ return ret;
+
+ return regmap_write(smi->map, reg, *val);
+}
+
+static irqreturn_t rtl8365mb_irq(int irq, void *data)
+{
+ struct realtek_smi *smi = data;
+ unsigned long line_changes = 0;
+ struct rtl8365mb *mb;
+ u32 stat;
+ int line;
+ int ret;
+
+ mb = smi->chip_data;
+
+ ret = rtl8365mb_get_and_clear_status_reg(smi, RTL8365MB_INTR_STATUS_REG,
+ &stat);
+ if (ret)
+ goto out_error;
+
+ if (stat & RTL8365MB_INTR_LINK_CHANGE_MASK) {
+ u32 linkdown_ind;
+ u32 linkup_ind;
+ u32 val;
+
+ ret = rtl8365mb_get_and_clear_status_reg(
+ smi, RTL8365MB_PORT_LINKUP_IND_REG, &val);
+ if (ret)
+ goto out_error;
+
+ linkup_ind = FIELD_GET(RTL8365MB_PORT_LINKUP_IND_MASK, val);
+
+ ret = rtl8365mb_get_and_clear_status_reg(
+ smi, RTL8365MB_PORT_LINKDOWN_IND_REG, &val);
+ if (ret)
+ goto out_error;
+
+ linkdown_ind = FIELD_GET(RTL8365MB_PORT_LINKDOWN_IND_MASK, val);
+
+ line_changes = (linkup_ind | linkdown_ind) & mb->port_mask;
+ }
+
+ if (!line_changes)
+ goto out_none;
+
+ for_each_set_bit(line, &line_changes, smi->num_ports) {
+ int child_irq = irq_find_mapping(smi->irqdomain, line);
+
+ handle_nested_irq(child_irq);
+ }
+
+ return IRQ_HANDLED;
+
+out_error:
+ dev_err(smi->dev, "failed to read interrupt status: %d\n", ret);
+
+out_none:
+ return IRQ_NONE;
+}
+
+static struct irq_chip rtl8365mb_irq_chip = {
+ .name = "rtl8365mb",
+ /* The hardware doesn't support masking IRQs on a per-port basis */
+};
+
+static int rtl8365mb_irq_map(struct irq_domain *domain, unsigned int irq,
+ irq_hw_number_t hwirq)
+{
+ irq_set_chip_data(irq, domain->host_data);
+ irq_set_chip_and_handler(irq, &rtl8365mb_irq_chip, handle_simple_irq);
+ irq_set_nested_thread(irq, 1);
+ irq_set_noprobe(irq);
+
+ return 0;
+}
+
+static void rtl8365mb_irq_unmap(struct irq_domain *d, unsigned int irq)
+{
+ irq_set_nested_thread(irq, 0);
+ irq_set_chip_and_handler(irq, NULL, NULL);
+ irq_set_chip_data(irq, NULL);
+}
+
+static const struct irq_domain_ops rtl8365mb_irqdomain_ops = {
+ .map = rtl8365mb_irq_map,
+ .unmap = rtl8365mb_irq_unmap,
+ .xlate = irq_domain_xlate_onecell,
+};
+
+static int rtl8365mb_set_irq_enable(struct realtek_smi *smi, bool enable)
+{
+ return regmap_update_bits(smi->map, RTL8365MB_INTR_CTRL_REG,
+ RTL8365MB_INTR_LINK_CHANGE_MASK,
+ FIELD_PREP(RTL8365MB_INTR_LINK_CHANGE_MASK,
+ enable ? 1 : 0));
+}
+
+static int rtl8365mb_irq_enable(struct realtek_smi *smi)
+{
+ return rtl8365mb_set_irq_enable(smi, true);
+}
+
+static int rtl8365mb_irq_disable(struct realtek_smi *smi)
+{
+ return rtl8365mb_set_irq_enable(smi, false);
+}
+
+static int rtl8365mb_irq_setup(struct realtek_smi *smi)
+{
+ struct rtl8365mb *mb = smi->chip_data;
+ struct device_node *intc;
+ u32 irq_trig;
+ int virq;
+ int irq;
+ u32 val;
+ int ret;
+ int i;
+
+ intc = of_get_child_by_name(smi->dev->of_node, "interrupt-controller");
+ if (!intc) {
+ dev_err(smi->dev, "missing child interrupt-controller node\n");
+ return -EINVAL;
+ }
+
+ smi->irqdomain = irq_domain_add_linear(intc, smi->num_ports,
+ &rtl8365mb_irqdomain_ops, smi);
+ if (!smi->irqdomain) {
+ dev_err(smi->dev, "failed to add irq domain\n");
+ ret = -ENOMEM;
+ goto out_put_node;
+ }
+
+ for (i = 0; i < smi->num_ports; i++) {
+ virq = irq_create_mapping(smi->irqdomain, i);
+ if (!virq) {
+ dev_err(smi->dev,
+ "failed to create irq domain mapping\n");
+ ret = -EINVAL;
+ goto out_remove_irqdomain;
+ }
+
+ irq_set_parent(virq, irq);
+ }
+
+ /* rtl8365mb IRQs cascade off this one */
+ irq = of_irq_get(intc, 0);
+ if (irq <= 0) {
+ if (irq != -EPROBE_DEFER)
+ dev_err(smi->dev, "failed to get parent irq: %d\n",
+ irq);
+ ret = irq ? irq : -EINVAL;
+ goto out_remove_irqdomain;
+ }
+
+ /* Configure chip interrupt signal polarity */
+ irq_trig = irqd_get_trigger_type(irq_get_irq_data(irq));
+ switch (irq_trig) {
+ case IRQF_TRIGGER_RISING:
+ case IRQF_TRIGGER_HIGH:
+ val = RTL8365MB_INTR_POLARITY_HIGH;
+ break;
+ case IRQF_TRIGGER_FALLING:
+ case IRQF_TRIGGER_LOW:
+ val = RTL8365MB_INTR_POLARITY_LOW;
+ break;
+ default:
+ dev_err(smi->dev, "unsupported irq trigger type %u\n",
+ irq_trig);
+ ret = -EINVAL;
+ goto out_remove_irqdomain;
+ }
+
+ ret = regmap_update_bits(smi->map, RTL8365MB_INTR_POLARITY_REG,
+ RTL8365MB_INTR_POLARITY_MASK,
+ FIELD_PREP(RTL8365MB_INTR_POLARITY_MASK, val));
+ if (ret)
+ goto out_remove_irqdomain;
+
+ /* Disable the interrupt in case the chip has it enabled on reset */
+ ret = rtl8365mb_irq_disable(smi);
+ if (ret)
+ goto out_remove_irqdomain;
+
+ /* Clear the interrupt status register */
+ ret = regmap_write(smi->map, RTL8365MB_INTR_STATUS_REG,
+ RTL8365MB_INTR_ALL_MASK);
+ if (ret)
+ goto out_remove_irqdomain;
+
+ ret = request_threaded_irq(irq, NULL, rtl8365mb_irq, IRQF_ONESHOT,
+ "rtl8365mb", smi);
+ if (ret) {
+ dev_err(smi->dev, "failed to request irq: %d\n", ret);
+ goto out_remove_irqdomain;
+ }
+
+ /* Store the irq so that we know to free it during teardown */
+ mb->irq = irq;
+
+ ret = rtl8365mb_irq_enable(smi);
+ if (ret)
+ goto out_free_irq;
+
+ of_node_put(intc);
+
+ return 0;
+
+out_free_irq:
+ free_irq(mb->irq, smi);
+ mb->irq = 0;
+
+out_remove_irqdomain:
+ for (i = 0; i < smi->num_ports; i++) {
+ virq = irq_find_mapping(smi->irqdomain, i);
+ irq_dispose_mapping(virq);
+ }
+
+ irq_domain_remove(smi->irqdomain);
+ smi->irqdomain = NULL;
+
+out_put_node:
+ of_node_put(intc);
+
+ return ret;
+}
+
+static void rtl8365mb_irq_teardown(struct realtek_smi *smi)
+{
+ struct rtl8365mb *mb = smi->chip_data;
+ int virq;
+ int i;
+
+ if (mb->irq) {
+ free_irq(mb->irq, smi);
+ mb->irq = 0;
+ }
+
+ if (smi->irqdomain) {
+ for (i = 0; i < smi->num_ports; i++) {
+ virq = irq_find_mapping(smi->irqdomain, i);
+ irq_dispose_mapping(virq);
+ }
+
+ irq_domain_remove(smi->irqdomain);
+ smi->irqdomain = NULL;
+ }
+}
+
+static int rtl8365mb_cpu_config(struct realtek_smi *smi)
+{
+ struct rtl8365mb *mb = smi->chip_data;
+ struct rtl8365mb_cpu *cpu = &mb->cpu;
+ u32 val;
+ int ret;
+
+ ret = regmap_update_bits(smi->map, RTL8365MB_CPU_PORT_MASK_REG,
+ RTL8365MB_CPU_PORT_MASK_MASK,
+ FIELD_PREP(RTL8365MB_CPU_PORT_MASK_MASK,
+ cpu->mask));
+ if (ret)
+ return ret;
+
+ val = FIELD_PREP(RTL8365MB_CPU_CTRL_EN_MASK, cpu->enable ? 1 : 0) |
+ FIELD_PREP(RTL8365MB_CPU_CTRL_INSERTMODE_MASK, cpu->insert) |
+ FIELD_PREP(RTL8365MB_CPU_CTRL_TAG_POSITION_MASK, cpu->position) |
+ FIELD_PREP(RTL8365MB_CPU_CTRL_RXBYTECOUNT_MASK, cpu->rx_length) |
+ FIELD_PREP(RTL8365MB_CPU_CTRL_TAG_FORMAT_MASK, cpu->format) |
+ FIELD_PREP(RTL8365MB_CPU_CTRL_TRAP_PORT_MASK, cpu->trap_port) |
+ FIELD_PREP(RTL8365MB_CPU_CTRL_TRAP_PORT_EXT_MASK,
+ cpu->trap_port >> 3);
+ ret = regmap_write(smi->map, RTL8365MB_CPU_CTRL_REG, val);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int rtl8365mb_switch_init(struct realtek_smi *smi)
+{
+ struct rtl8365mb *mb = smi->chip_data;
+ int ret;
+ int i;
+
+ /* Do any chip-specific init jam before getting to the common stuff */
+ if (mb->jam_table) {
+ for (i = 0; i < mb->jam_size; i++) {
+ ret = regmap_write(smi->map, mb->jam_table[i].reg,
+ mb->jam_table[i].val);
+ if (ret)
+ return ret;
+ }
+ }
+
+ /* Common init jam */
+ for (i = 0; i < ARRAY_SIZE(rtl8365mb_init_jam_common); i++) {
+ ret = regmap_write(smi->map, rtl8365mb_init_jam_common[i].reg,
+ rtl8365mb_init_jam_common[i].val);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+static int rtl8365mb_reset_chip(struct realtek_smi *smi)
+{
+ u32 val;
+
+ realtek_smi_write_reg_noack(smi, RTL8365MB_CHIP_RESET_REG,
+ FIELD_PREP(RTL8365MB_CHIP_RESET_HW_MASK,
+ 1));
+
+ /* Realtek documentation says the chip needs 1 second to reset. Sleep
+ * for 100 ms before accessing any registers to prevent ACK timeouts.
+ */
+ msleep(100);
+ return regmap_read_poll_timeout(smi->map, RTL8365MB_CHIP_RESET_REG, val,
+ !(val & RTL8365MB_CHIP_RESET_HW_MASK),
+ 20000, 1e6);
+}
+
+static int rtl8365mb_setup(struct dsa_switch *ds)
+{
+ struct realtek_smi *smi = ds->priv;
+ struct rtl8365mb *mb;
+ int ret;
+ int i;
+
+ mb = smi->chip_data;
+
+ ret = rtl8365mb_reset_chip(smi);
+ if (ret) {
+ dev_err(smi->dev, "failed to reset chip: %d\n", ret);
+ goto out_error;
+ }
+
+ /* Configure switch to vendor-defined initial state */
+ ret = rtl8365mb_switch_init(smi);
+ if (ret) {
+ dev_err(smi->dev, "failed to initialize switch: %d\n", ret);
+ goto out_error;
+ }
+
+ /* Set up cascading IRQs */
+ ret = rtl8365mb_irq_setup(smi);
+ if (ret == -EPROBE_DEFER)
+ return ret;
+ else if (ret)
+ dev_info(smi->dev, "no interrupt support\n");
+
+ /* Configure CPU tagging */
+ ret = rtl8365mb_cpu_config(smi);
+ if (ret)
+ goto out_teardown_irq;
+
+ /* Configure ports */
+ for (i = 0; i < smi->num_ports; i++) {
+ struct rtl8365mb_port *p = &mb->ports[i];
+
+ if (dsa_is_unused_port(smi->ds, i))
+ continue;
+
+ /* Set up per-port private data */
+ p->smi = smi;
+ p->index = i;
+
+ /* Forward only to the CPU */
+ ret = rtl8365mb_port_set_isolation(smi, i, BIT(smi->cpu_port));
+ if (ret)
+ goto out_teardown_irq;
+
+ /* Disable learning */
+ ret = rtl8365mb_port_set_learning(smi, i, false);
+ if (ret)
+ goto out_teardown_irq;
+
+ /* Set the initial STP state of all ports to DISABLED, otherwise
+ * ports will still forward frames to the CPU despite being
+ * administratively down by default.
+ */
+ rtl8365mb_port_stp_state_set(smi->ds, i, BR_STATE_DISABLED);
+ }
+
+ /* Set maximum packet length to 1536 bytes */
+ ret = regmap_update_bits(smi->map, RTL8365MB_CFG0_MAX_LEN_REG,
+ RTL8365MB_CFG0_MAX_LEN_MASK,
+ FIELD_PREP(RTL8365MB_CFG0_MAX_LEN_MASK, 1536));
+ if (ret)
+ goto out_teardown_irq;
+
+ ret = realtek_smi_setup_mdio(smi);
+ if (ret) {
+ dev_err(smi->dev, "could not set up MDIO bus\n");
+ goto out_teardown_irq;
+ }
+
+ /* Start statistics counter polling */
+ rtl8365mb_stats_setup(smi);
+
+ return 0;
+
+out_teardown_irq:
+ rtl8365mb_irq_teardown(smi);
+
+out_error:
+ return ret;
+}
+
+static void rtl8365mb_teardown(struct dsa_switch *ds)
+{
+ struct realtek_smi *smi = ds->priv;
+
+ rtl8365mb_stats_teardown(smi);
+ rtl8365mb_irq_teardown(smi);
+}
+
+static int rtl8365mb_get_chip_id_and_ver(struct regmap *map, u32 *id, u32 *ver)
+{
+ int ret;
+
+ /* For some reason we have to write a magic value to an arbitrary
+ * register whenever accessing the chip ID/version registers.
+ */
+ ret = regmap_write(map, RTL8365MB_MAGIC_REG, RTL8365MB_MAGIC_VALUE);
+ if (ret)
+ return ret;
+
+ ret = regmap_read(map, RTL8365MB_CHIP_ID_REG, id);
+ if (ret)
+ return ret;
+
+ ret = regmap_read(map, RTL8365MB_CHIP_VER_REG, ver);
+ if (ret)
+ return ret;
+
+ /* Reset magic register */
+ ret = regmap_write(map, RTL8365MB_MAGIC_REG, 0);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int rtl8365mb_detect(struct realtek_smi *smi)
+{
+ struct rtl8365mb *mb = smi->chip_data;
+ u32 chip_id;
+ u32 chip_ver;
+ int ret;
+
+ ret = rtl8365mb_get_chip_id_and_ver(smi->map, &chip_id, &chip_ver);
+ if (ret) {
+ dev_err(smi->dev, "failed to read chip id and version: %d\n",
+ ret);
+ return ret;
+ }
+
+ switch (chip_id) {
+ case RTL8365MB_CHIP_ID_8365MB_VC:
+ dev_info(smi->dev,
+ "found an RTL8365MB-VC switch (ver=0x%04x)\n",
+ chip_ver);
+
+ smi->cpu_port = RTL8365MB_CPU_PORT_NUM_8365MB_VC;
+ smi->num_ports = smi->cpu_port + 1;
+
+ mb->smi = smi;
+ mb->chip_id = chip_id;
+ mb->chip_ver = chip_ver;
+ mb->port_mask = BIT(smi->num_ports) - 1;
+ mb->learn_limit_max = RTL8365MB_LEARN_LIMIT_MAX_8365MB_VC;
+ mb->jam_table = rtl8365mb_init_jam_8365mb_vc;
+ mb->jam_size = ARRAY_SIZE(rtl8365mb_init_jam_8365mb_vc);
+
+ mb->cpu.enable = 1;
+ mb->cpu.mask = BIT(smi->cpu_port);
+ mb->cpu.trap_port = smi->cpu_port;
+ mb->cpu.insert = RTL8365MB_CPU_INSERT_TO_ALL;
+ mb->cpu.position = RTL8365MB_CPU_POS_AFTER_SA;
+ mb->cpu.rx_length = RTL8365MB_CPU_RXLEN_64BYTES;
+ mb->cpu.format = RTL8365MB_CPU_FORMAT_8BYTES;
+
+ break;
+ default:
+ dev_err(smi->dev,
+ "found an unknown Realtek switch (id=0x%04x, ver=0x%04x)\n",
+ chip_id, chip_ver);
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static const struct dsa_switch_ops rtl8365mb_switch_ops = {
+ .get_tag_protocol = rtl8365mb_get_tag_protocol,
+ .setup = rtl8365mb_setup,
+ .teardown = rtl8365mb_teardown,
+ .phylink_validate = rtl8365mb_phylink_validate,
+ .phylink_mac_config = rtl8365mb_phylink_mac_config,
+ .phylink_mac_link_down = rtl8365mb_phylink_mac_link_down,
+ .phylink_mac_link_up = rtl8365mb_phylink_mac_link_up,
+ .port_stp_state_set = rtl8365mb_port_stp_state_set,
+ .get_strings = rtl8365mb_get_strings,
+ .get_ethtool_stats = rtl8365mb_get_ethtool_stats,
+ .get_sset_count = rtl8365mb_get_sset_count,
+ .get_eth_phy_stats = rtl8365mb_get_phy_stats,
+ .get_eth_mac_stats = rtl8365mb_get_mac_stats,
+ .get_eth_ctrl_stats = rtl8365mb_get_ctrl_stats,
+ .get_stats64 = rtl8365mb_get_stats64,
+};
+
+static const struct realtek_smi_ops rtl8365mb_smi_ops = {
+ .detect = rtl8365mb_detect,
+ .phy_read = rtl8365mb_phy_read,
+ .phy_write = rtl8365mb_phy_write,
+};
+
+const struct realtek_smi_variant rtl8365mb_variant = {
+ .ds_ops = &rtl8365mb_switch_ops,
+ .ops = &rtl8365mb_smi_ops,
+ .clk_delay = 10,
+ .cmd_read = 0xb9,
+ .cmd_write = 0xb8,
+ .chip_data_sz = sizeof(struct rtl8365mb),
+};
+EXPORT_SYMBOL_GPL(rtl8365mb_variant);