| Message ID | 20211217150854.2081-7-granquet@baylibre.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | drm/mediatek: Add mt8195 DisplayPort driver | expand |
On 17-12-21, 16:08, Guillaume Ranquet wrote: > From: Markus Schneider-Pargmann <msp@baylibre.com> Pls cc relevant folks on cover so that they know what is going on in the series... Is this dependent on rest? It should not and can be sent and reviewed separately! > This is a new driver that supports the integrated DisplayPort phy for > mediatek SoCs, especially the mt8195. The phy is integrated into the > DisplayPort controller and will be created by the mtk-dp driver. This > driver expects a struct regmap to be able to work on the same registers > as the DisplayPort controller. It sets the device data to be the struct > phy so that the DisplayPort controller can easily work with it. > > The driver does not have any devicetree bindings because the datasheet > does not list the controller and the phy as distinct units. > > The interaction with the controller can be covered by the configure > callback of the phy framework and its displayport parameters. > > Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> > Signed-off-by: Guillaume Ranquet <granquet@baylibre.com> > --- > MAINTAINERS | 1 + > drivers/phy/mediatek/Kconfig | 8 ++ > drivers/phy/mediatek/Makefile | 1 + > drivers/phy/mediatek/phy-mtk-dp.c | 219 ++++++++++++++++++++++++++++++ > 4 files changed, 229 insertions(+) > create mode 100644 drivers/phy/mediatek/phy-mtk-dp.c > > diff --git a/MAINTAINERS b/MAINTAINERS > index 8b7a98daf8e05..c44829d8a74df 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -6394,6 +6394,7 @@ L: linux-mediatek@lists.infradead.org (moderated for non-subscribers) > S: Supported > F: Documentation/devicetree/bindings/display/mediatek/ > F: drivers/gpu/drm/mediatek/ > +F: drivers/phy/mediatek/phy-mtk-dp.c > F: drivers/phy/mediatek/phy-mtk-hdmi* > F: drivers/phy/mediatek/phy-mtk-mipi* > > diff --git a/drivers/phy/mediatek/Kconfig b/drivers/phy/mediatek/Kconfig > index 55f8e6c048ab3..f7ec860590492 100644 > --- a/drivers/phy/mediatek/Kconfig > +++ b/drivers/phy/mediatek/Kconfig > @@ -55,3 +55,11 @@ config PHY_MTK_MIPI_DSI > select GENERIC_PHY > help > Support MIPI DSI for Mediatek SoCs. > + > +config PHY_MTK_DP > + tristate "MediaTek DP-PHY Driver" > + depends on ARCH_MEDIATEK || COMPILE_TEST > + depends on OF > + select GENERIC_PHY > + help > + Support DisplayPort PHY for Mediatek SoCs. > diff --git a/drivers/phy/mediatek/Makefile b/drivers/phy/mediatek/Makefile > index ace660fbed3a1..4ba1e06504346 100644 > --- a/drivers/phy/mediatek/Makefile > +++ b/drivers/phy/mediatek/Makefile > @@ -3,6 +3,7 @@ > # Makefile for the phy drivers. > # > > +obj-$(CONFIG_PHY_MTK_DP) += phy-mtk-dp.o > obj-$(CONFIG_PHY_MTK_TPHY) += phy-mtk-tphy.o > obj-$(CONFIG_PHY_MTK_UFS) += phy-mtk-ufs.o > obj-$(CONFIG_PHY_MTK_XSPHY) += phy-mtk-xsphy.o > diff --git a/drivers/phy/mediatek/phy-mtk-dp.c b/drivers/phy/mediatek/phy-mtk-dp.c > new file mode 100644 > index 0000000000000..e0de2a367e788 > --- /dev/null > +++ b/drivers/phy/mediatek/phy-mtk-dp.c > @@ -0,0 +1,219 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Copyright (c) 2021 BayLibre > + * Author: Markus Schneider-Pargmann <msp@baylibre.com> > + */ > + > +#include <linux/delay.h> > +#include <linux/io.h> > +#include <linux/of.h> > +#include <linux/phy/phy.h> > +#include <linux/platform_device.h> > +#include <linux/regmap.h> > + > +#define PHY_OFFSET 0x1000 > + > +#define MTK_DP_PHY_DIG_PLL_CTL_1 (PHY_OFFSET + 0x014) > +# define TPLL_SSC_EN BIT(3) > + > +#define MTK_DP_PHY_DIG_BIT_RATE (PHY_OFFSET + 0x03C) > +# define BIT_RATE_RBR 0 > +# define BIT_RATE_HBR 1 > +# define BIT_RATE_HBR2 2 > +# define BIT_RATE_HBR3 3 > + > +#define MTK_DP_PHY_DIG_SW_RST (PHY_OFFSET + 0x038) > +# define DP_GLB_SW_RST_PHYD BIT(0) > + > +#define MTK_DP_LANE0_DRIVING_PARAM_3 (PHY_OFFSET + 0x138) > +#define MTK_DP_LANE1_DRIVING_PARAM_3 (PHY_OFFSET + 0x238) > +#define MTK_DP_LANE2_DRIVING_PARAM_3 (PHY_OFFSET + 0x338) > +#define MTK_DP_LANE3_DRIVING_PARAM_3 (PHY_OFFSET + 0x438) > +# define XTP_LN_TX_LCTXC0_SW0_PRE0_DEFAULT 0x10 > +# define XTP_LN_TX_LCTXC0_SW0_PRE1_DEFAULT (0x14 << 8) > +# define XTP_LN_TX_LCTXC0_SW0_PRE2_DEFAULT (0x18 << 16) > +# define XTP_LN_TX_LCTXC0_SW0_PRE3_DEFAULT (0x20 << 24) how about defining constants and using FEILD_PREP() to set the value. Here and few other places! > +static int mtk_dp_phy_configure(struct phy *phy, union phy_configure_opts *opts) > +{ > + struct mtk_dp_phy *dp_phy = phy_get_drvdata(phy); > + u32 val; > + > + if (opts->dp.set_rate) { > + switch (opts->dp.link_rate) { > + default: > + dev_err(&phy->dev, > + "Implementation error, unknown linkrate %x\n", > + opts->dp.link_rate); > + return -EINVAL; > + case 1620: > + val = BIT_RATE_RBR; > + break; > + case 2700: > + val = BIT_RATE_HBR; > + break; > + case 5400: > + val = BIT_RATE_HBR2; > + break; > + case 8100: > + val = BIT_RATE_HBR3; > + break; > + } > + regmap_write(dp_phy->regs, MTK_DP_PHY_DIG_BIT_RATE, val); interesting use of default :) which is correct! But why keep the regmap_write inside switch, you are anyway returning in default, so this write could be outside as well
Hi Vinod, Quoting Vinod Koul (2021-12-29 07:00:34) > > On 17-12-21, 16:08, Guillaume Ranquet wrote: > > From: Markus Schneider-Pargmann <msp@baylibre.com> > > Pls cc relevant folks on cover so that they know what is going on in the > series... Is this dependent on rest? It should not and can be sent and > reviewed separately! > Sorry, I'm a bit of a noob... I've used the get_maintainers.pl script to get the to: and cc: for each patch. I'll make sure the cover has everyone included in the next revision. The phy is not dependant on the rest, but this phy cannot be used outside of the mt8195 Display Port context... as the phy is actually the same IP as the DP. The DP driver has a functional dependency with the phy, they can be split into two series as they both merge/compile on their own. Do you want me to split the series with the phy on one hand the the DP driver on the other? > > This is a new driver that supports the integrated DisplayPort phy for > > mediatek SoCs, especially the mt8195. The phy is integrated into the > > DisplayPort controller and will be created by the mtk-dp driver. This > > driver expects a struct regmap to be able to work on the same registers > > as the DisplayPort controller. It sets the device data to be the struct > > phy so that the DisplayPort controller can easily work with it. > > > > The driver does not have any devicetree bindings because the datasheet > > does not list the controller and the phy as distinct units. > > > > The interaction with the controller can be covered by the configure > > callback of the phy framework and its displayport parameters. > > > > Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> > > Signed-off-by: Guillaume Ranquet <granquet@baylibre.com> > > --- > > MAINTAINERS | 1 + > > drivers/phy/mediatek/Kconfig | 8 ++ > > drivers/phy/mediatek/Makefile | 1 + > > drivers/phy/mediatek/phy-mtk-dp.c | 219 ++++++++++++++++++++++++++++++ > > 4 files changed, 229 insertions(+) > > create mode 100644 drivers/phy/mediatek/phy-mtk-dp.c > > > > diff --git a/MAINTAINERS b/MAINTAINERS > > index 8b7a98daf8e05..c44829d8a74df 100644 > > --- a/MAINTAINERS > > +++ b/MAINTAINERS > > @@ -6394,6 +6394,7 @@ L: linux-mediatek@lists.infradead.org (moderated for non-subscribers) > > S: Supported > > F: Documentation/devicetree/bindings/display/mediatek/ > > F: drivers/gpu/drm/mediatek/ > > +F: drivers/phy/mediatek/phy-mtk-dp.c > > F: drivers/phy/mediatek/phy-mtk-hdmi* > > F: drivers/phy/mediatek/phy-mtk-mipi* > > > > diff --git a/drivers/phy/mediatek/Kconfig b/drivers/phy/mediatek/Kconfig > > index 55f8e6c048ab3..f7ec860590492 100644 > > --- a/drivers/phy/mediatek/Kconfig > > +++ b/drivers/phy/mediatek/Kconfig > > @@ -55,3 +55,11 @@ config PHY_MTK_MIPI_DSI > > select GENERIC_PHY > > help > > Support MIPI DSI for Mediatek SoCs. > > + > > +config PHY_MTK_DP > > + tristate "MediaTek DP-PHY Driver" > > + depends on ARCH_MEDIATEK || COMPILE_TEST > > + depends on OF > > + select GENERIC_PHY > > + help > > + Support DisplayPort PHY for Mediatek SoCs. > > diff --git a/drivers/phy/mediatek/Makefile b/drivers/phy/mediatek/Makefile > > index ace660fbed3a1..4ba1e06504346 100644 > > --- a/drivers/phy/mediatek/Makefile > > +++ b/drivers/phy/mediatek/Makefile > > @@ -3,6 +3,7 @@ > > # Makefile for the phy drivers. > > # > > > > +obj-$(CONFIG_PHY_MTK_DP) += phy-mtk-dp.o > > obj-$(CONFIG_PHY_MTK_TPHY) += phy-mtk-tphy.o > > obj-$(CONFIG_PHY_MTK_UFS) += phy-mtk-ufs.o > > obj-$(CONFIG_PHY_MTK_XSPHY) += phy-mtk-xsphy.o > > diff --git a/drivers/phy/mediatek/phy-mtk-dp.c b/drivers/phy/mediatek/phy-mtk-dp.c > > new file mode 100644 > > index 0000000000000..e0de2a367e788 > > --- /dev/null > > +++ b/drivers/phy/mediatek/phy-mtk-dp.c > > @@ -0,0 +1,219 @@ > > +// SPDX-License-Identifier: GPL-2.0 > > +/* > > + * Copyright (c) 2021 BayLibre > > + * Author: Markus Schneider-Pargmann <msp@baylibre.com> > > + */ > > + > > +#include <linux/delay.h> > > +#include <linux/io.h> > > +#include <linux/of.h> > > +#include <linux/phy/phy.h> > > +#include <linux/platform_device.h> > > +#include <linux/regmap.h> > > + > > +#define PHY_OFFSET 0x1000 > > + > > +#define MTK_DP_PHY_DIG_PLL_CTL_1 (PHY_OFFSET + 0x014) > > +# define TPLL_SSC_EN BIT(3) > > + > > +#define MTK_DP_PHY_DIG_BIT_RATE (PHY_OFFSET + 0x03C) > > +# define BIT_RATE_RBR 0 > > +# define BIT_RATE_HBR 1 > > +# define BIT_RATE_HBR2 2 > > +# define BIT_RATE_HBR3 3 > > + > > +#define MTK_DP_PHY_DIG_SW_RST (PHY_OFFSET + 0x038) > > +# define DP_GLB_SW_RST_PHYD BIT(0) > > + > > +#define MTK_DP_LANE0_DRIVING_PARAM_3 (PHY_OFFSET + 0x138) > > +#define MTK_DP_LANE1_DRIVING_PARAM_3 (PHY_OFFSET + 0x238) > > +#define MTK_DP_LANE2_DRIVING_PARAM_3 (PHY_OFFSET + 0x338) > > +#define MTK_DP_LANE3_DRIVING_PARAM_3 (PHY_OFFSET + 0x438) > > +# define XTP_LN_TX_LCTXC0_SW0_PRE0_DEFAULT 0x10 > > +# define XTP_LN_TX_LCTXC0_SW0_PRE1_DEFAULT (0x14 << 8) > > +# define XTP_LN_TX_LCTXC0_SW0_PRE2_DEFAULT (0x18 << 16) > > +# define XTP_LN_TX_LCTXC0_SW0_PRE3_DEFAULT (0x20 << 24) > > how about defining constants and using FEILD_PREP() to set the value. > Here and few other places! > Noted for next revision, Thanks. > > +static int mtk_dp_phy_configure(struct phy *phy, union phy_configure_opts *opts) > > +{ > > + struct mtk_dp_phy *dp_phy = phy_get_drvdata(phy); > > + u32 val; > > + > > + if (opts->dp.set_rate) { > > + switch (opts->dp.link_rate) { > > + default: > > + dev_err(&phy->dev, > > + "Implementation error, unknown linkrate %x\n", > > + opts->dp.link_rate); > > + return -EINVAL; > > + case 1620: > > + val = BIT_RATE_RBR; > > + break; > > + case 2700: > > + val = BIT_RATE_HBR; > > + break; > > + case 5400: > > + val = BIT_RATE_HBR2; > > + break; > > + case 8100: > > + val = BIT_RATE_HBR3; > > + break; > > + } > > + regmap_write(dp_phy->regs, MTK_DP_PHY_DIG_BIT_RATE, val); > > interesting use of default :) which is correct! > > But why keep the regmap_write inside switch, you are anyway returning in > default, so this write could be outside as well Not my code here (as we are upstreaming code from the vendor tree). My understanding is that the regmap_write() shouldn't be called if dp.set_rate is false as val won't be set. This doesn't actually happen because the only client for this phy is the DP driver and we make sure to call it with dp.set_rate to true. > -- > ~Vinod Thx, Guillaume.
Hi, Guillaume: On Fri, 2021-12-17 at 16:08 +0100, Guillaume Ranquet wrote: > From: Markus Schneider-Pargmann <msp@baylibre.com> > > This is a new driver that supports the integrated DisplayPort phy for > mediatek SoCs, especially the mt8195. The phy is integrated into the > DisplayPort controller and will be created by the mtk-dp driver. This > driver expects a struct regmap to be able to work on the same > registers > as the DisplayPort controller. It sets the device data to be the > struct > phy so that the DisplayPort controller can easily work with it. > > The driver does not have any devicetree bindings because the > datasheet > does not list the controller and the phy as distinct units. > > The interaction with the controller can be covered by the configure > callback of the phy framework and its displayport parameters. > > Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> > Signed-off-by: Guillaume Ranquet <granquet@baylibre.com> > --- > MAINTAINERS | 1 + > drivers/phy/mediatek/Kconfig | 8 ++ > drivers/phy/mediatek/Makefile | 1 + > drivers/phy/mediatek/phy-mtk-dp.c | 219 > ++++++++++++++++++++++++++++++ > 4 files changed, 229 insertions(+) > create mode 100644 drivers/phy/mediatek/phy-mtk-dp.c > > diff --git a/MAINTAINERS b/MAINTAINERS > index 8b7a98daf8e05..c44829d8a74df 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -6394,6 +6394,7 @@ L: linux-mediatek@lists.infradead.org > (moderated for non-subscribers) > S: Supported > F: Documentation/devicetree/bindings/display/mediatek/ > F: drivers/gpu/drm/mediatek/ > +F: drivers/phy/mediatek/phy-mtk-dp.c > F: drivers/phy/mediatek/phy-mtk-hdmi* > F: drivers/phy/mediatek/phy-mtk-mipi* > > diff --git a/drivers/phy/mediatek/Kconfig > b/drivers/phy/mediatek/Kconfig > index 55f8e6c048ab3..f7ec860590492 100644 > --- a/drivers/phy/mediatek/Kconfig > +++ b/drivers/phy/mediatek/Kconfig > @@ -55,3 +55,11 @@ config PHY_MTK_MIPI_DSI > select GENERIC_PHY > help > Support MIPI DSI for Mediatek SoCs. > + > +config PHY_MTK_DP > + tristate "MediaTek DP-PHY Driver" > + depends on ARCH_MEDIATEK || COMPILE_TEST > + depends on OF > + select GENERIC_PHY > + help > + Support DisplayPort PHY for Mediatek SoCs. > diff --git a/drivers/phy/mediatek/Makefile > b/drivers/phy/mediatek/Makefile > index ace660fbed3a1..4ba1e06504346 100644 > --- a/drivers/phy/mediatek/Makefile > +++ b/drivers/phy/mediatek/Makefile > @@ -3,6 +3,7 @@ > # Makefile for the phy drivers. > # > > +obj-$(CONFIG_PHY_MTK_DP) += phy-mtk-dp.o > obj-$(CONFIG_PHY_MTK_TPHY) += phy-mtk-tphy.o > obj-$(CONFIG_PHY_MTK_UFS) += phy-mtk-ufs.o > obj-$(CONFIG_PHY_MTK_XSPHY) += phy-mtk-xsphy.o > diff --git a/drivers/phy/mediatek/phy-mtk-dp.c > b/drivers/phy/mediatek/phy-mtk-dp.c > new file mode 100644 > index 0000000000000..e0de2a367e788 > --- /dev/null > +++ b/drivers/phy/mediatek/phy-mtk-dp.c > @@ -0,0 +1,219 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Copyright (c) 2021 BayLibre > + * Author: Markus Schneider-Pargmann <msp@baylibre.com> > + */ > + > +#include <linux/delay.h> > +#include <linux/io.h> > +#include <linux/of.h> > +#include <linux/phy/phy.h> > +#include <linux/platform_device.h> > +#include <linux/regmap.h> > + > +#define PHY_OFFSET 0x1000 > + > +#define MTK_DP_PHY_DIG_PLL_CTL_1 (PHY_OFFSET + 0x014) > +# define TPLL_SSC_EN BIT(3) > + > +#define MTK_DP_PHY_DIG_BIT_RATE (PHY_OFFSET + > 0x03C) > +# define BIT_RATE_RBR 0 > +# define BIT_RATE_HBR 1 > +# define BIT_RATE_HBR2 2 > +# define BIT_RATE_HBR3 3 > + I would like to align the indent style to Mediatek mipi dsi phy driver and Mediatek hdmi phy driver. That means the bitwise definition value has one more indent. > +#define MTK_DP_PHY_DIG_SW_RST (PHY_OFFSET + > 0x038) > +# define DP_GLB_SW_RST_PHYD BIT(0) > + > +#define MTK_DP_LANE0_DRIVING_PARAM_3 (PHY_OFFSET + 0x138) > +#define MTK_DP_LANE1_DRIVING_PARAM_3 (PHY_OFFSET + 0x238) > +#define MTK_DP_LANE2_DRIVING_PARAM_3 (PHY_OFFSET + 0x338) > +#define MTK_DP_LANE3_DRIVING_PARAM_3 (PHY_OFFSET + 0x438) > +# define XTP_LN_TX_LCTXC0_SW0_PRE0_DEFAULT 0x10 > +# define XTP_LN_TX_LCTXC0_SW0_PRE1_DEFAULT (0x14 << 8) > +# define XTP_LN_TX_LCTXC0_SW0_PRE2_DEFAULT (0x18 << 16) > +# define XTP_LN_TX_LCTXC0_SW0_PRE3_DEFAULT (0x20 << 24) > +# define DRIVING_PARAM_3_DEFAULT (XTP_LN_TX_LCTXC0_SW0_P > RE0_DEFAULT | \ > + XTP_LN_TX_LCTXC0_SW0_P > RE1_DEFAULT | \ > + XTP_LN_TX_LCTXC0_SW0_P > RE2_DEFAULT | \ > + XTP_LN_TX_LCTXC0_SW0_P > RE3_DEFAULT) > + > +#define MTK_DP_LANE0_DRIVING_PARAM_4 (PHY_OFFSET + 0x13C) > +#define MTK_DP_LANE1_DRIVING_PARAM_4 (PHY_OFFSET + 0x23C) > +#define MTK_DP_LANE2_DRIVING_PARAM_4 (PHY_OFFSET + 0x33C) > +#define MTK_DP_LANE3_DRIVING_PARAM_4 (PHY_OFFSET + 0x43C) Useless, so remove. > +# define XTP_LN_TX_LCTXC0_SW1_PRE0_DEFAULT 0x18 > +# define XTP_LN_TX_LCTXC0_SW1_PRE1_DEFAULT (0x1e << 8) > +# define XTP_LN_TX_LCTXC0_SW1_PRE2_DEFAULT (0x24 << 16) > +# define XTP_LN_TX_LCTXC0_SW2_PRE0_DEFAULT (0x20 << 24) > +# define DRIVING_PARAM_4_DEFAULT (XTP_LN_TX_LCTXC0_SW1_P > RE0_DEFAULT | \ > + XTP_LN_TX_LCTXC0_SW1_P > RE1_DEFAULT | \ > + XTP_LN_TX_LCTXC0_SW1_P > RE2_DEFAULT | \ > + XTP_LN_TX_LCTXC0_SW2_P > RE0_DEFAULT) > + > +#define MTK_DP_LANE0_DRIVING_PARAM_5 (PHY_OFFSET + 0x140) > +#define MTK_DP_LANE1_DRIVING_PARAM_5 (PHY_OFFSET + 0x240) > +#define MTK_DP_LANE2_DRIVING_PARAM_5 (PHY_OFFSET + 0x340) > +#define MTK_DP_LANE3_DRIVING_PARAM_5 (PHY_OFFSET + 0x440) Ditto. > +# define XTP_LN_TX_LCTXC0_SW2_PRE1_DEFAULT 0x28 > +# define XTP_LN_TX_LCTXC0_SW3_PRE0_DEFAULT (0x30 << 8) > +# define DRIVING_PARAM_5_DEFAULT (XTP_LN_TX_LCTXC0_SW2_P > RE1_DEFAULT | \ > + XTP_LN_TX_LCTXC0_SW3_P > RE0_DEFAULT) > + > +#define MTK_DP_LANE0_DRIVING_PARAM_6 (PHY_OFFSET + 0x144) > +#define MTK_DP_LANE1_DRIVING_PARAM_6 (PHY_OFFSET + 0x244) > +#define MTK_DP_LANE2_DRIVING_PARAM_6 (PHY_OFFSET + 0x344) > +#define MTK_DP_LANE3_DRIVING_PARAM_6 (PHY_OFFSET + 0x444) Ditto. > +# define XTP_LN_TX_LCTXCP1_SW0_PRE0_DEFAULT 0x00 > +# define XTP_LN_TX_LCTXCP1_SW0_PRE1_DEFAULT (0x04 << 8) > +# define XTP_LN_TX_LCTXCP1_SW0_PRE2_DEFAULT (0x08 << 16) > +# define XTP_LN_TX_LCTXCP1_SW0_PRE3_DEFAULT (0x10 << 24) > +# define DRIVING_PARAM_6_DEFAULT (XTP_LN_TX_LCTXCP1_SW0_ > PRE0_DEFAULT | \ > + XTP_LN_TX_LCTXCP1_SW0_ > PRE1_DEFAULT | \ > + XTP_LN_TX_LCTXCP1_SW0_ > PRE2_DEFAULT | \ > + XTP_LN_TX_LCTXCP1_SW0_ > PRE3_DEFAULT) > + > +#define MTK_DP_LANE0_DRIVING_PARAM_7 (PHY_OFFSET + 0x148) > +#define MTK_DP_LANE1_DRIVING_PARAM_7 (PHY_OFFSET + 0x248) > +#define MTK_DP_LANE2_DRIVING_PARAM_7 (PHY_OFFSET + 0x348) > +#define MTK_DP_LANE3_DRIVING_PARAM_7 (PHY_OFFSET + 0x448) Ditto. > +# define XTP_LN_TX_LCTXCP1_SW1_PRE0_DEFAULT 0x00 > +# define XTP_LN_TX_LCTXCP1_SW1_PRE1_DEFAULT (0x06 << 8) > +# define XTP_LN_TX_LCTXCP1_SW1_PRE2_DEFAULT (0x0c << 16) > +# define XTP_LN_TX_LCTXCP1_SW2_PRE0_DEFAULT (0x00 << 24) > +# define DRIVING_PARAM_7_DEFAULT (XTP_LN_TX_LCTXCP1_SW1_ > PRE0_DEFAULT | \ > + XTP_LN_TX_LCTXCP1_SW1_ > PRE1_DEFAULT | \ > + XTP_LN_TX_LCTXCP1_SW1_ > PRE2_DEFAULT | \ > + XTP_LN_TX_LCTXCP1_SW2_ > PRE0_DEFAULT) > + > +#define MTK_DP_LANE0_DRIVING_PARAM_8 (PHY_OFFSET + 0x14C) > +#define MTK_DP_LANE1_DRIVING_PARAM_8 (PHY_OFFSET + 0x24C) > +#define MTK_DP_LANE2_DRIVING_PARAM_8 (PHY_OFFSET + 0x34C) > +#define MTK_DP_LANE3_DRIVING_PARAM_8 (PHY_OFFSET + 0x44C) Ditto. > +# define XTP_LN_TX_LCTXCP1_SW2_PRE1_DEFAULT 0x08 > +# define XTP_LN_TX_LCTXCP1_SW3_PRE0_DEFAULT (0x00 << 8) > +# define DRIVING_PARAM_8_DEFAULT (XTP_LN_TX_LCTXCP1_SW2_ > PRE1_DEFAULT | \ > + XTP_LN_TX_LCTXCP1_SW3_ > PRE0_DEFAULT) > + > +struct mtk_dp_phy { > + struct regmap *regs; > +}; > + > +static int mtk_dp_phy_init(struct phy *phy) > +{ > + struct mtk_dp_phy *dp_phy = phy_get_drvdata(phy); > + u32 driving_params[] = { > + DRIVING_PARAM_3_DEFAULT, > + DRIVING_PARAM_4_DEFAULT, > + DRIVING_PARAM_5_DEFAULT, > + DRIVING_PARAM_6_DEFAULT, > + DRIVING_PARAM_7_DEFAULT, > + DRIVING_PARAM_8_DEFAULT > + }; > + > + regmap_bulk_write(dp_phy->regs, MTK_DP_LANE0_DRIVING_PARAM_3, > + driving_params, ARRAY_SIZE(driving_params)); > + regmap_bulk_write(dp_phy->regs, MTK_DP_LANE1_DRIVING_PARAM_3, > + driving_params, ARRAY_SIZE(driving_params)); > + regmap_bulk_write(dp_phy->regs, MTK_DP_LANE2_DRIVING_PARAM_3, > + driving_params, ARRAY_SIZE(driving_params)); > + regmap_bulk_write(dp_phy->regs, MTK_DP_LANE3_DRIVING_PARAM_3, > + driving_params, ARRAY_SIZE(driving_params)); > + > + return 0; > +} > + > +static int mtk_dp_phy_configure(struct phy *phy, union > phy_configure_opts *opts) > +{ > + struct mtk_dp_phy *dp_phy = phy_get_drvdata(phy); > + u32 val; > + > + if (opts->dp.set_rate) { > + switch (opts->dp.link_rate) { > + default: > + dev_err(&phy->dev, > + "Implementation error, unknown linkrate > %x\n", > + opts->dp.link_rate); > + return -EINVAL; > + case 1620: > + val = BIT_RATE_RBR; > + break; > + case 2700: > + val = BIT_RATE_HBR; > + break; > + case 5400: > + val = BIT_RATE_HBR2; > + break; > + case 8100: > + val = BIT_RATE_HBR3; > + break; > + } > + regmap_write(dp_phy->regs, MTK_DP_PHY_DIG_BIT_RATE, > val); > + } > + > + regmap_update_bits(dp_phy->regs, MTK_DP_PHY_DIG_PLL_CTL_1, > + TPLL_SSC_EN, opts->dp.ssc ? TPLL_SSC_EN : > 0); > + > + return 0; > +} > + > +static int mtk_dp_phy_reset(struct phy *phy) > +{ > + struct mtk_dp_phy *dp_phy = phy_get_drvdata(phy); > + > + regmap_update_bits(dp_phy->regs, MTK_DP_PHY_DIG_SW_RST, > + DP_GLB_SW_RST_PHYD, 0); > + usleep_range(50, 200); > + regmap_update_bits(dp_phy->regs, MTK_DP_PHY_DIG_SW_RST, > + DP_GLB_SW_RST_PHYD, 1); > + > + return 0; > +} > + > +static const struct phy_ops mtk_dp_phy_dev_ops = { > + .init = mtk_dp_phy_init, > + .configure = mtk_dp_phy_configure, > + .reset = mtk_dp_phy_reset, > In Mediatek mipi dsi phy driver and Mediatek hdmi phy driver, implement power_on and power_off. I would like to align the behavior. If init is necessary for configure, would exit should be implement? > + .owner = THIS_MODULE, > +}; > + > +static int mtk_dp_phy_probe(struct platform_device *pdev) > +{ > + struct device *dev = &pdev->dev; > + struct mtk_dp_phy *dp_phy; > + struct phy *phy; > + > + dp_phy = devm_kzalloc(dev, sizeof(*dp_phy), GFP_KERNEL); > + if (!dp_phy) > + return -ENOMEM; > + > + dp_phy->regs = *(struct regmap **)dev->platform_data; Why not mtk_dp->phy_dev = platform_device_register_data(dev, "mediatek- dp-phy", PLATFORM_DEVID_ AUTO, mtk_dp->regs, sizeof(struct regmap *)); And dp_phy->regs = (struct regmap *)dev->platform_data; Regards, CK > + if (!dp_phy->regs) { > + dev_err(dev, "No data passed, requires struct > regmap**\n"); > + return -EINVAL; > + } > + > + phy = devm_phy_create(dev, NULL, &mtk_dp_phy_dev_ops); > + if (IS_ERR(phy)) { > + dev_err(dev, "Failed to create DP PHY: %ld\n", > PTR_ERR(phy)); > + return PTR_ERR(phy); > + } > + phy_set_drvdata(phy, dp_phy); > + > + if (!dev->of_node) > + phy_create_lookup(phy, "dp", dev_name(dev)); > + > + return 0; > +} > + > +struct platform_driver mtk_dp_phy_driver = { > + .probe = mtk_dp_phy_probe, > + .driver = { > + .name = "mediatek-dp-phy", > + }, > +}; > +module_platform_driver(mtk_dp_phy_driver); > + > +MODULE_AUTHOR("Markus Schneider-Pargmann <msp@baylibre.com>"); > +MODULE_DESCRIPTION("MediaTek DP PHY Driver"); > +MODULE_LICENSE("GPL v2");
diff --git a/MAINTAINERS b/MAINTAINERS index 8b7a98daf8e05..c44829d8a74df 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -6394,6 +6394,7 @@ L: linux-mediatek@lists.infradead.org (moderated for non-subscribers) S: Supported F: Documentation/devicetree/bindings/display/mediatek/ F: drivers/gpu/drm/mediatek/ +F: drivers/phy/mediatek/phy-mtk-dp.c F: drivers/phy/mediatek/phy-mtk-hdmi* F: drivers/phy/mediatek/phy-mtk-mipi* diff --git a/drivers/phy/mediatek/Kconfig b/drivers/phy/mediatek/Kconfig index 55f8e6c048ab3..f7ec860590492 100644 --- a/drivers/phy/mediatek/Kconfig +++ b/drivers/phy/mediatek/Kconfig @@ -55,3 +55,11 @@ config PHY_MTK_MIPI_DSI select GENERIC_PHY help Support MIPI DSI for Mediatek SoCs. + +config PHY_MTK_DP + tristate "MediaTek DP-PHY Driver" + depends on ARCH_MEDIATEK || COMPILE_TEST + depends on OF + select GENERIC_PHY + help + Support DisplayPort PHY for Mediatek SoCs. diff --git a/drivers/phy/mediatek/Makefile b/drivers/phy/mediatek/Makefile index ace660fbed3a1..4ba1e06504346 100644 --- a/drivers/phy/mediatek/Makefile +++ b/drivers/phy/mediatek/Makefile @@ -3,6 +3,7 @@ # Makefile for the phy drivers. # +obj-$(CONFIG_PHY_MTK_DP) += phy-mtk-dp.o obj-$(CONFIG_PHY_MTK_TPHY) += phy-mtk-tphy.o obj-$(CONFIG_PHY_MTK_UFS) += phy-mtk-ufs.o obj-$(CONFIG_PHY_MTK_XSPHY) += phy-mtk-xsphy.o diff --git a/drivers/phy/mediatek/phy-mtk-dp.c b/drivers/phy/mediatek/phy-mtk-dp.c new file mode 100644 index 0000000000000..e0de2a367e788 --- /dev/null +++ b/drivers/phy/mediatek/phy-mtk-dp.c @@ -0,0 +1,219 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2021 BayLibre + * Author: Markus Schneider-Pargmann <msp@baylibre.com> + */ + +#include <linux/delay.h> +#include <linux/io.h> +#include <linux/of.h> +#include <linux/phy/phy.h> +#include <linux/platform_device.h> +#include <linux/regmap.h> + +#define PHY_OFFSET 0x1000 + +#define MTK_DP_PHY_DIG_PLL_CTL_1 (PHY_OFFSET + 0x014) +# define TPLL_SSC_EN BIT(3) + +#define MTK_DP_PHY_DIG_BIT_RATE (PHY_OFFSET + 0x03C) +# define BIT_RATE_RBR 0 +# define BIT_RATE_HBR 1 +# define BIT_RATE_HBR2 2 +# define BIT_RATE_HBR3 3 + +#define MTK_DP_PHY_DIG_SW_RST (PHY_OFFSET + 0x038) +# define DP_GLB_SW_RST_PHYD BIT(0) + +#define MTK_DP_LANE0_DRIVING_PARAM_3 (PHY_OFFSET + 0x138) +#define MTK_DP_LANE1_DRIVING_PARAM_3 (PHY_OFFSET + 0x238) +#define MTK_DP_LANE2_DRIVING_PARAM_3 (PHY_OFFSET + 0x338) +#define MTK_DP_LANE3_DRIVING_PARAM_3 (PHY_OFFSET + 0x438) +# define XTP_LN_TX_LCTXC0_SW0_PRE0_DEFAULT 0x10 +# define XTP_LN_TX_LCTXC0_SW0_PRE1_DEFAULT (0x14 << 8) +# define XTP_LN_TX_LCTXC0_SW0_PRE2_DEFAULT (0x18 << 16) +# define XTP_LN_TX_LCTXC0_SW0_PRE3_DEFAULT (0x20 << 24) +# define DRIVING_PARAM_3_DEFAULT (XTP_LN_TX_LCTXC0_SW0_PRE0_DEFAULT | \ + XTP_LN_TX_LCTXC0_SW0_PRE1_DEFAULT | \ + XTP_LN_TX_LCTXC0_SW0_PRE2_DEFAULT | \ + XTP_LN_TX_LCTXC0_SW0_PRE3_DEFAULT) + +#define MTK_DP_LANE0_DRIVING_PARAM_4 (PHY_OFFSET + 0x13C) +#define MTK_DP_LANE1_DRIVING_PARAM_4 (PHY_OFFSET + 0x23C) +#define MTK_DP_LANE2_DRIVING_PARAM_4 (PHY_OFFSET + 0x33C) +#define MTK_DP_LANE3_DRIVING_PARAM_4 (PHY_OFFSET + 0x43C) +# define XTP_LN_TX_LCTXC0_SW1_PRE0_DEFAULT 0x18 +# define XTP_LN_TX_LCTXC0_SW1_PRE1_DEFAULT (0x1e << 8) +# define XTP_LN_TX_LCTXC0_SW1_PRE2_DEFAULT (0x24 << 16) +# define XTP_LN_TX_LCTXC0_SW2_PRE0_DEFAULT (0x20 << 24) +# define DRIVING_PARAM_4_DEFAULT (XTP_LN_TX_LCTXC0_SW1_PRE0_DEFAULT | \ + XTP_LN_TX_LCTXC0_SW1_PRE1_DEFAULT | \ + XTP_LN_TX_LCTXC0_SW1_PRE2_DEFAULT | \ + XTP_LN_TX_LCTXC0_SW2_PRE0_DEFAULT) + +#define MTK_DP_LANE0_DRIVING_PARAM_5 (PHY_OFFSET + 0x140) +#define MTK_DP_LANE1_DRIVING_PARAM_5 (PHY_OFFSET + 0x240) +#define MTK_DP_LANE2_DRIVING_PARAM_5 (PHY_OFFSET + 0x340) +#define MTK_DP_LANE3_DRIVING_PARAM_5 (PHY_OFFSET + 0x440) +# define XTP_LN_TX_LCTXC0_SW2_PRE1_DEFAULT 0x28 +# define XTP_LN_TX_LCTXC0_SW3_PRE0_DEFAULT (0x30 << 8) +# define DRIVING_PARAM_5_DEFAULT (XTP_LN_TX_LCTXC0_SW2_PRE1_DEFAULT | \ + XTP_LN_TX_LCTXC0_SW3_PRE0_DEFAULT) + +#define MTK_DP_LANE0_DRIVING_PARAM_6 (PHY_OFFSET + 0x144) +#define MTK_DP_LANE1_DRIVING_PARAM_6 (PHY_OFFSET + 0x244) +#define MTK_DP_LANE2_DRIVING_PARAM_6 (PHY_OFFSET + 0x344) +#define MTK_DP_LANE3_DRIVING_PARAM_6 (PHY_OFFSET + 0x444) +# define XTP_LN_TX_LCTXCP1_SW0_PRE0_DEFAULT 0x00 +# define XTP_LN_TX_LCTXCP1_SW0_PRE1_DEFAULT (0x04 << 8) +# define XTP_LN_TX_LCTXCP1_SW0_PRE2_DEFAULT (0x08 << 16) +# define XTP_LN_TX_LCTXCP1_SW0_PRE3_DEFAULT (0x10 << 24) +# define DRIVING_PARAM_6_DEFAULT (XTP_LN_TX_LCTXCP1_SW0_PRE0_DEFAULT | \ + XTP_LN_TX_LCTXCP1_SW0_PRE1_DEFAULT | \ + XTP_LN_TX_LCTXCP1_SW0_PRE2_DEFAULT | \ + XTP_LN_TX_LCTXCP1_SW0_PRE3_DEFAULT) + +#define MTK_DP_LANE0_DRIVING_PARAM_7 (PHY_OFFSET + 0x148) +#define MTK_DP_LANE1_DRIVING_PARAM_7 (PHY_OFFSET + 0x248) +#define MTK_DP_LANE2_DRIVING_PARAM_7 (PHY_OFFSET + 0x348) +#define MTK_DP_LANE3_DRIVING_PARAM_7 (PHY_OFFSET + 0x448) +# define XTP_LN_TX_LCTXCP1_SW1_PRE0_DEFAULT 0x00 +# define XTP_LN_TX_LCTXCP1_SW1_PRE1_DEFAULT (0x06 << 8) +# define XTP_LN_TX_LCTXCP1_SW1_PRE2_DEFAULT (0x0c << 16) +# define XTP_LN_TX_LCTXCP1_SW2_PRE0_DEFAULT (0x00 << 24) +# define DRIVING_PARAM_7_DEFAULT (XTP_LN_TX_LCTXCP1_SW1_PRE0_DEFAULT | \ + XTP_LN_TX_LCTXCP1_SW1_PRE1_DEFAULT | \ + XTP_LN_TX_LCTXCP1_SW1_PRE2_DEFAULT | \ + XTP_LN_TX_LCTXCP1_SW2_PRE0_DEFAULT) + +#define MTK_DP_LANE0_DRIVING_PARAM_8 (PHY_OFFSET + 0x14C) +#define MTK_DP_LANE1_DRIVING_PARAM_8 (PHY_OFFSET + 0x24C) +#define MTK_DP_LANE2_DRIVING_PARAM_8 (PHY_OFFSET + 0x34C) +#define MTK_DP_LANE3_DRIVING_PARAM_8 (PHY_OFFSET + 0x44C) +# define XTP_LN_TX_LCTXCP1_SW2_PRE1_DEFAULT 0x08 +# define XTP_LN_TX_LCTXCP1_SW3_PRE0_DEFAULT (0x00 << 8) +# define DRIVING_PARAM_8_DEFAULT (XTP_LN_TX_LCTXCP1_SW2_PRE1_DEFAULT | \ + XTP_LN_TX_LCTXCP1_SW3_PRE0_DEFAULT) + +struct mtk_dp_phy { + struct regmap *regs; +}; + +static int mtk_dp_phy_init(struct phy *phy) +{ + struct mtk_dp_phy *dp_phy = phy_get_drvdata(phy); + u32 driving_params[] = { + DRIVING_PARAM_3_DEFAULT, + DRIVING_PARAM_4_DEFAULT, + DRIVING_PARAM_5_DEFAULT, + DRIVING_PARAM_6_DEFAULT, + DRIVING_PARAM_7_DEFAULT, + DRIVING_PARAM_8_DEFAULT + }; + + regmap_bulk_write(dp_phy->regs, MTK_DP_LANE0_DRIVING_PARAM_3, + driving_params, ARRAY_SIZE(driving_params)); + regmap_bulk_write(dp_phy->regs, MTK_DP_LANE1_DRIVING_PARAM_3, + driving_params, ARRAY_SIZE(driving_params)); + regmap_bulk_write(dp_phy->regs, MTK_DP_LANE2_DRIVING_PARAM_3, + driving_params, ARRAY_SIZE(driving_params)); + regmap_bulk_write(dp_phy->regs, MTK_DP_LANE3_DRIVING_PARAM_3, + driving_params, ARRAY_SIZE(driving_params)); + + return 0; +} + +static int mtk_dp_phy_configure(struct phy *phy, union phy_configure_opts *opts) +{ + struct mtk_dp_phy *dp_phy = phy_get_drvdata(phy); + u32 val; + + if (opts->dp.set_rate) { + switch (opts->dp.link_rate) { + default: + dev_err(&phy->dev, + "Implementation error, unknown linkrate %x\n", + opts->dp.link_rate); + return -EINVAL; + case 1620: + val = BIT_RATE_RBR; + break; + case 2700: + val = BIT_RATE_HBR; + break; + case 5400: + val = BIT_RATE_HBR2; + break; + case 8100: + val = BIT_RATE_HBR3; + break; + } + regmap_write(dp_phy->regs, MTK_DP_PHY_DIG_BIT_RATE, val); + } + + regmap_update_bits(dp_phy->regs, MTK_DP_PHY_DIG_PLL_CTL_1, + TPLL_SSC_EN, opts->dp.ssc ? TPLL_SSC_EN : 0); + + return 0; +} + +static int mtk_dp_phy_reset(struct phy *phy) +{ + struct mtk_dp_phy *dp_phy = phy_get_drvdata(phy); + + regmap_update_bits(dp_phy->regs, MTK_DP_PHY_DIG_SW_RST, + DP_GLB_SW_RST_PHYD, 0); + usleep_range(50, 200); + regmap_update_bits(dp_phy->regs, MTK_DP_PHY_DIG_SW_RST, + DP_GLB_SW_RST_PHYD, 1); + + return 0; +} + +static const struct phy_ops mtk_dp_phy_dev_ops = { + .init = mtk_dp_phy_init, + .configure = mtk_dp_phy_configure, + .reset = mtk_dp_phy_reset, + .owner = THIS_MODULE, +}; + +static int mtk_dp_phy_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct mtk_dp_phy *dp_phy; + struct phy *phy; + + dp_phy = devm_kzalloc(dev, sizeof(*dp_phy), GFP_KERNEL); + if (!dp_phy) + return -ENOMEM; + + dp_phy->regs = *(struct regmap **)dev->platform_data; + if (!dp_phy->regs) { + dev_err(dev, "No data passed, requires struct regmap**\n"); + return -EINVAL; + } + + phy = devm_phy_create(dev, NULL, &mtk_dp_phy_dev_ops); + if (IS_ERR(phy)) { + dev_err(dev, "Failed to create DP PHY: %ld\n", PTR_ERR(phy)); + return PTR_ERR(phy); + } + phy_set_drvdata(phy, dp_phy); + + if (!dev->of_node) + phy_create_lookup(phy, "dp", dev_name(dev)); + + return 0; +} + +struct platform_driver mtk_dp_phy_driver = { + .probe = mtk_dp_phy_probe, + .driver = { + .name = "mediatek-dp-phy", + }, +}; +module_platform_driver(mtk_dp_phy_driver); + +MODULE_AUTHOR("Markus Schneider-Pargmann <msp@baylibre.com>"); +MODULE_DESCRIPTION("MediaTek DP PHY Driver"); +MODULE_LICENSE("GPL v2");