new file mode 100644
@@ -0,0 +1,241 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/ufs/qcom,ufs.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Universal Flash Storage (UFS) Controller
+
+maintainers:
+ - Yaniv Gardi <ygardi@codeaurora.org>
+
+# Select only our matches, not all jedec,ufs-2.0
+select:
+ properties:
+ compatible:
+ contains:
+ const: qcom,ufshc
+ required:
+ - compatible
+
+properties:
+ compatible:
+ items:
+ - enum:
+ - qcom,msm8994-ufshc
+ - qcom,msm8996-ufshc
+ - qcom,msm8998-ufshc
+ - qcom,sdm845-ufshc
+ - qcom,sm8150-ufshc
+ - qcom,sm8250-ufshc
+ - qcom,sm8350-ufshc
+ - qcom,sm8450-ufshc
+ - const: qcom,ufshc
+ - const: jedec,ufs-2.0
+
+ clocks:
+ minItems: 8
+ maxItems: 11
+
+ clock-names:
+ minItems: 8
+ maxItems: 11
+
+ interconnects:
+ minItems: 2
+ maxItems: 2
+
+ interconnect-names:
+ items:
+ - const: ufs-ddr
+ - const: cpu-ufs
+
+ iommus:
+ minItems: 1
+ maxItems: 2
+
+ phys:
+ maxItems: 1
+
+ phy-names:
+ items:
+ - const: ufsphy
+
+ power-domains:
+ maxItems: 1
+
+ reg:
+ minItems: 1
+ maxItems: 2
+
+ resets:
+ maxItems: 1
+
+ '#reset-cells':
+ const: 1
+
+ reset-names:
+ items:
+ - const: rst
+
+ reset-gpios:
+ maxItems: 1
+ description:
+ GPIO connected to the RESET pin of the UFS memory device.
+
+required:
+ - compatible
+ - reg
+
+allOf:
+ - $ref: ufs-common.yaml
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - qcom,msm8998-ufshc
+ - qcom,sm8250-ufshc
+ - qcom,sm8350-ufshc
+ - qcom,sm8450-ufshc
+ then:
+ properties:
+ clocks:
+ minItems: 8
+ maxItems: 8
+ clock-names:
+ items:
+ - const: core_clk
+ - const: bus_aggr_clk
+ - const: iface_clk
+ - const: core_clk_unipro
+ - const: ref_clk
+ - const: tx_lane0_sync_clk
+ - const: rx_lane0_sync_clk
+ - const: rx_lane1_sync_clk
+ reg:
+ minItems: 1
+ maxItems: 1
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - qcom,sdm845-ufshc
+ - qcom,sm8150-ufshc
+ then:
+ properties:
+ clocks:
+ minItems: 9
+ maxItems: 9
+ clock-names:
+ items:
+ - const: core_clk
+ - const: bus_aggr_clk
+ - const: iface_clk
+ - const: core_clk_unipro
+ - const: ref_clk
+ - const: tx_lane0_sync_clk
+ - const: rx_lane0_sync_clk
+ - const: rx_lane1_sync_clk
+ - const: ice_core_clk
+ reg:
+ minItems: 2
+ maxItems: 2
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - qcom,msm8996-ufshc
+ then:
+ properties:
+ clocks:
+ minItems: 11
+ maxItems: 11
+ clock-names:
+ items:
+ - const: core_clk_src
+ - const: core_clk
+ - const: bus_clk
+ - const: bus_aggr_clk
+ - const: iface_clk
+ - const: core_clk_unipro_src
+ - const: core_clk_unipro
+ - const: core_clk_ice
+ - const: ref_clk
+ - const: tx_lane0_sync_clk
+ - const: rx_lane0_sync_clk
+ reg:
+ minItems: 1
+ maxItems: 1
+
+ # TODO: define clock bindings for qcom,msm8994-ufshc
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/qcom,gcc-sm8450.h>
+ #include <dt-bindings/clock/qcom,rpmh.h>
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interconnect/qcom,sm8450.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ ufs@1d84000 {
+ compatible = "qcom,sm8450-ufshc", "qcom,ufshc",
+ "jedec,ufs-2.0";
+ reg = <0 0x01d84000 0 0x3000>;
+ interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&ufs_mem_phy_lanes>;
+ phy-names = "ufsphy";
+ lanes-per-direction = <2>;
+ #reset-cells = <1>;
+ resets = <&gcc GCC_UFS_PHY_BCR>;
+ reset-names = "rst";
+ reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
+
+ vcc-supply = <&vreg_l7b_2p5>;
+ vcc-max-microamp = <1100000>;
+ vccq-supply = <&vreg_l9b_1p2>;
+ vccq-max-microamp = <1200000>;
+
+ power-domains = <&gcc UFS_PHY_GDSC>;
+ iommus = <&apps_smmu 0xe0 0x0>;
+ interconnects = <&aggre1_noc MASTER_UFS_MEM &mc_virt SLAVE_EBI1>,
+ <&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_UFS_MEM_CFG>;
+ interconnect-names = "ufs-ddr", "cpu-ufs";
+
+ clock-names = "core_clk",
+ "bus_aggr_clk",
+ "iface_clk",
+ "core_clk_unipro",
+ "ref_clk",
+ "tx_lane0_sync_clk",
+ "rx_lane0_sync_clk",
+ "rx_lane1_sync_clk";
+ clocks = <&gcc GCC_UFS_PHY_AXI_CLK>,
+ <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
+ <&gcc GCC_UFS_PHY_AHB_CLK>,
+ <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>,
+ <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
+ <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
+ <&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
+ freq-table = <75000000 300000000>,
+ <0 0>,
+ <0 0>,
+ <75000000 300000000>,
+ <75000000 300000000>,
+ <0 0>,
+ <0 0>,
+ <0 0>;
+ };
+ };
deleted file mode 100644
@@ -1,90 +0,0 @@
-* Universal Flash Storage (UFS) Host Controller
-
-UFSHC nodes are defined to describe on-chip UFS host controllers.
-Each UFS controller instance should have its own node.
-
-Required properties:
-- compatible : must contain "jedec,ufs-1.1" or "jedec,ufs-2.0"
-
- For Qualcomm SoCs must contain, as below, an
- SoC-specific compatible along with "qcom,ufshc" and
- the appropriate jedec string:
- "qcom,msm8994-ufshc", "qcom,ufshc", "jedec,ufs-2.0"
- "qcom,msm8996-ufshc", "qcom,ufshc", "jedec,ufs-2.0"
- "qcom,msm8998-ufshc", "qcom,ufshc", "jedec,ufs-2.0"
- "qcom,sdm845-ufshc", "qcom,ufshc", "jedec,ufs-2.0"
- "qcom,sm8150-ufshc", "qcom,ufshc", "jedec,ufs-2.0"
- "qcom,sm8250-ufshc", "qcom,ufshc", "jedec,ufs-2.0"
- "qcom,sm8350-ufshc", "qcom,ufshc", "jedec,ufs-2.0"
- "qcom,sm8450-ufshc", "qcom,ufshc", "jedec,ufs-2.0"
-- interrupts : <interrupt mapping for UFS host controller IRQ>
-- reg : <registers mapping>
-
-Optional properties:
-- phys : phandle to UFS PHY node
-- phy-names : the string "ufsphy" when is found in a node, along
- with "phys" attribute, provides phandle to UFS PHY node
-- vdd-hba-supply : phandle to UFS host controller supply regulator node
-- vcc-supply : phandle to VCC supply regulator node
-- vccq-supply : phandle to VCCQ supply regulator node
-- vccq2-supply : phandle to VCCQ2 supply regulator node
-- vcc-supply-1p8 : For embedded UFS devices, valid VCC range is 1.7-1.95V
- or 2.7-3.6V. This boolean property when set, specifies
- to use low voltage range of 1.7-1.95V. Note for external
- UFS cards this property is invalid and valid VCC range is
- always 2.7-3.6V.
-- vcc-max-microamp : specifies max. load that can be drawn from vcc supply
-- vccq-max-microamp : specifies max. load that can be drawn from vccq supply
-- vccq2-max-microamp : specifies max. load that can be drawn from vccq2 supply
-
-- clocks : List of phandle and clock specifier pairs
-- clock-names : List of clock input name strings sorted in the same
- order as the clocks property.
- "ref_clk" indicates reference clock frequency.
- UFS host supplies reference clock to UFS device and UFS device
- specification allows host to provide one of the 4 frequencies (19.2 MHz,
- 26 MHz, 38.4 MHz, 52MHz) for reference clock. This "ref_clk" entry is
- parsed and used to update the reference clock setting in device.
- Defaults to 26 MHz(as per specification) if not specified by host.
-- freq-table-hz : Array of <min max> operating frequencies stored in the same
- order as the clocks property. If this property is not
- defined or a value in the array is "0" then it is assumed
- that the frequency is set by the parent clock or a
- fixed rate clock source.
--lanes-per-direction : number of lanes available per direction - either 1 or 2.
- Note that it is assume same number of lanes is used both
- directions at once. If not specified, default is 2 lanes per direction.
-- #reset-cells : Must be <1> for Qualcomm UFS controllers that expose
- PHY reset from the UFS controller.
-- resets : reset node register
-- reset-names : describe reset node register, the "rst" corresponds to reset the whole UFS IP.
-- reset-gpios : A phandle and gpio specifier denoting the GPIO connected
- to the RESET pin of the UFS memory device.
-
-Note: If above properties are not defined it can be assumed that the supply
-regulators or clocks are always on.
-
-Example:
- ufshc@fc598000 {
- compatible = "jedec,ufs-1.1";
- reg = <0xfc598000 0x800>;
- interrupts = <0 28 0>;
-
- vdd-hba-supply = <&xxx_reg0>;
- vcc-supply = <&xxx_reg1>;
- vcc-supply-1p8;
- vccq-supply = <&xxx_reg2>;
- vccq2-supply = <&xxx_reg3>;
- vcc-max-microamp = 500000;
- vccq-max-microamp = 200000;
- vccq2-max-microamp = 200000;
-
- clocks = <&core 0>, <&ref 0>, <&phy 0>, <&iface 0>;
- clock-names = "core_clk", "ref_clk", "phy_clk", "iface_clk";
- freq-table-hz = <100000000 200000000>, <0 0>, <0 0>, <0 0>;
- resets = <&reset 0 1>;
- reset-names = "rst";
- phys = <&ufsphy1>;
- phy-names = "ufsphy";
- #reset-cells = <1>;
- };
Convert the Qualcomm Universal Flash Storage (UFS) Controller to DT schema format. Except the conversion, add also properties already present in DTS: iommus, interconnects and power-domains. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> --- .../devicetree/bindings/ufs/qcom,ufs.yaml | 241 ++++++++++++++++++ .../devicetree/bindings/ufs/ufshcd-pltfrm.txt | 90 ------- 2 files changed, 241 insertions(+), 90 deletions(-) create mode 100644 Documentation/devicetree/bindings/ufs/qcom,ufs.yaml delete mode 100644 Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt